From: Brian Norris <computersforpeace@gmail.com>
To: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-mtd@lists.infradead.org, linux-kernel@vger.kernel.org,
Boris Brezillon <boris.brezillon@free-electrons.com>,
Richard Weinberger <richard@nod.at>,
David Woodhouse <dwmw2@infradead.org>
Subject: [GIT PULL] MTD updates for 4.9-rc1
Date: Sat, 8 Oct 2016 21:47:30 -0700 [thread overview]
Message-ID: <20161009044730.GB10199@brian-ubuntu> (raw)
Hi Linus,
I've not been very active this cycle, so these are mostly from Boris,
for the NAND flash subsystem.
The following changes since commit 29b4817d4018df78086157ea3a55c1d9424a7cfc:
Linux 4.8-rc1 (2016-08-07 18:18:00 -0700)
are available in the git repository at:
git://git.infradead.org/linux-mtd.git tags/for-linus-20161008
for you to fetch changes up to 69db4aa44fdd8befc2eccd1313d841c5128c385c:
Merge tag '4.9/mtd-pairing-scheme' of github.com:linux-nand/linux (2016-10-08 20:56:54 -0700)
----------------------------------------------------------------
MTD updates for 4.9-rc1
NAND:
* Add the infrastructure to automate NAND timings configuration
* Provide a generic DT property to maximize ECC strength
* Some refactoring in the core bad block table handling, to help with
improving some of the logic in error cases.
* Minor cleanups and fixes
MTD:
* Add APIs for handling page pairing; this is necessary for reliably
supporting MLC and TLC NAND flash, where paired-page disturbance affects
reliability. Upper layers (e.g., UBI) should make use of these in the near
future.
----------------------------------------------------------------
Andrey Smirnov (4):
Kconfig: nand: Make MTD_NAND_FSL_ELBC depend on FSL_SOC
Kconfig: nand: Remove redundant dependency on MTD_NAND
mtd: nand: Error out if cmd_ctrl() is missing
mtd: nand: Get rid of needless 'goto'
Boris Brezillon (11):
mtd: introduce the mtd_pairing_scheme concept
mtd: nand: timings: Fix tADL_min for ONFI 4.0 chips
mtd: nand: timings: Reorder tRR_min def in mode 0
mtd: nand_bbt: Move BBT block selection logic out of write_bbt()
mtd: nand: automate NAND timings selection
mtd: nand: Add an option to maximize the ECC strength
mtd: nand: Support maximizing ECC when using software BCH
mtd: nand: sunxi: Support ECC maximization
mtd: nand: Fix nand_command_lp() for 8bits opcodes
mtd: nand: mxc: Test CONFIG_OF instead of CONFIG_OF_MTD
mtd: Kill the OF_MTD Kconfig option
Brian Norris (4):
mtd: nand: sh_flctl: handle dma_submit() errors
Merge tag 'for-4.9' of github.com:linux-nand/linux
mtd: nand: fix trivial spelling error
Merge tag '4.9/mtd-pairing-scheme' of github.com:linux-nand/linux
Han Xu (1):
mtd: nand: gpmi: get correct free oob space
Harvey Hunt (1):
MAINTAINERS: Add maintainer entry for Ingenic JZ4780 NAND driver
Karl Beldan (1):
mtd: nand: davinci: Reinitialize the HW ECC engine in 4bit hwctl
Krzysztof Kozlowski (1):
mtd: nand: s3c2410: Register cpufreq notifier only on S3C24xx
Kyle Roeschley (1):
mtd: nand_bbt: scan for next free bbt block if writing bbt fails
Marc Gonzalez (1):
mtd: nand: import nand_hw_control_init()
Ray Jui (1):
mtd: brcmnand: iProc big endian and ONFI support
Richard Weinberger (2):
mtd: nand: Provide nand_cleanup() function to free NAND related resources
mtdpart: Propagate _get/put_device()
Roger Quadros (2):
mtd: nand: omap2: Don't call dma_release_channel() if dma_request_chan() failed
mtd: nand: Allow MTD_NAND_OMAP2 to be usable on Keystone devices
Sascha Hauer (9):
mtd: nand: remove unnecessary 'extern' from function declarations
mtd: nand: Create a NAND reset function
mtd: nand: Introduce nand_data_interface
mtd: nand: convert ONFI mode into data interface
mtd: nand: Add function to convert ONFI mode to data_interface
mtd: nand: Expose data interface for ONFI mode 0
mtd: nand: sunxi: switch from manual to automated timing config
mtd: nand: mxc: implement onfi get/set features
mtd: nand: mxc: Add timing setup for v2 controllers
Documentation/devicetree/bindings/mtd/nand.txt | 9 +
MAINTAINERS | 6 +
drivers/mtd/mtdcore.c | 104 ++++++
drivers/mtd/mtdpart.c | 19 +
drivers/mtd/nand/Kconfig | 12 +-
drivers/mtd/nand/bf5xx_nand.c | 3 +-
drivers/mtd/nand/brcmnand/brcmnand.c | 15 +-
drivers/mtd/nand/brcmnand/brcmnand.h | 13 +-
drivers/mtd/nand/brcmnand/iproc_nand.c | 18 +-
drivers/mtd/nand/davinci_nand.c | 3 +
drivers/mtd/nand/docg4.c | 3 +-
drivers/mtd/nand/fsl_elbc_nand.c | 3 +-
drivers/mtd/nand/fsl_ifc_nand.c | 3 +-
drivers/mtd/nand/gpmi-nand/gpmi-nand.c | 3 +-
drivers/mtd/nand/jz4780_nand.c | 3 +-
drivers/mtd/nand/mxc_nand.c | 137 ++++++-
drivers/mtd/nand/nand_base.c | 260 ++++++++++++--
drivers/mtd/nand/nand_bbt.c | 161 ++++++---
drivers/mtd/nand/nand_timings.c | 470 ++++++++++++++-----------
drivers/mtd/nand/ndfc.c | 3 +-
drivers/mtd/nand/omap2.c | 2 +-
drivers/mtd/nand/pxa3xx_nand.c | 3 +-
drivers/mtd/nand/qcom_nandc.c | 3 +-
drivers/mtd/nand/s3c2410.c | 7 +-
drivers/mtd/nand/sh_flctl.c | 8 +-
drivers/mtd/nand/sunxi_nand.c | 108 +++---
drivers/mtd/nand/txx9ndfmc.c | 3 +-
drivers/of/Kconfig | 4 -
include/linux/mtd/mtd.h | 107 ++++++
include/linux/mtd/nand.h | 234 ++++++++----
30 files changed, 1267 insertions(+), 460 deletions(-)
reply other threads:[~2016-10-09 4:47 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20161009044730.GB10199@brian-ubuntu \
--to=computersforpeace@gmail.com \
--cc=boris.brezillon@free-electrons.com \
--cc=dwmw2@infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mtd@lists.infradead.org \
--cc=richard@nod.at \
--cc=torvalds@linux-foundation.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).