From mboxrd@z Thu Jan 1 00:00:00 1970 Received: from mail.free-electrons.com ([62.4.15.54]) by bombadil.infradead.org with esmtp (Exim 4.87 #1 (Red Hat Linux)) id 1cqyTm-0005wH-Ck for linux-mtd@lists.infradead.org; Thu, 23 Mar 2017 08:52:24 +0000 Date: Thu, 23 Mar 2017 09:52:00 +0100 From: Boris Brezillon To: Masahiro Yamada Cc: linux-mtd@lists.infradead.org, David Woodhouse , Marek Vasut , Brian Norris , thorsten.christiansson@idquantique.com, laurent.monat@idquantique.com, Dinh Nguyen , Artem Bityutskiy , Graham Moore , Enrico Jorns , Chuanxiao Dong , Masami Hiramatsu , Jassi Brar , Rob Herring Subject: Re: [RESEND PATCH v2 42/53] mtd: nand: denali: switch over to cmd_ctrl instead of cmdfunc Message-ID: <20170323095200.282c50e5@bbrezillon> In-Reply-To: <1490228282-10805-16-git-send-email-yamada.masahiro@socionext.com> References: <1490228282-10805-1-git-send-email-yamada.masahiro@socionext.com> <1490228282-10805-16-git-send-email-yamada.masahiro@socionext.com> MIME-Version: 1.0 Content-Type: text/plain; charset=US-ASCII Content-Transfer-Encoding: 7bit List-Id: Linux MTD discussion mailing list List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , On Thu, 23 Mar 2017 09:17:51 +0900 Masahiro Yamada wrote: > The NAND_CMD_SET_FEATURES support is missing from denali_cmdfunc(). > This is needed for nand_onfi_set_features(). It would be possible > to add it in the current implementation, but having ->cmd_ctrl() > seems a better approach from the discussion with Boris [1]. > > Rely on the default implementation for ->cmdfunc() and implement > the driver's own ->cmd_ctrl(). > > Also add ->write_byte(), which is needed to write parameters for > NAND_CMD_SET_FEATURES. I'll review more carefully, but it goes in the right direction. Thanks a lot for doing that! > > [1] https://lkml.org/lkml/2017/3/15/97 > > Signed-off-by: Masahiro Yamada > --- > > Changes in v2: > - Newly added > > drivers/mtd/nand/denali.c | 104 +++++++++++++++++++++++----------------------- > 1 file changed, 52 insertions(+), 52 deletions(-) > > diff --git a/drivers/mtd/nand/denali.c b/drivers/mtd/nand/denali.c > index c0b8179..2d25b2f 100644 > --- a/drivers/mtd/nand/denali.c > +++ b/drivers/mtd/nand/denali.c > @@ -230,20 +230,16 @@ static uint32_t denali_wait_for_irq(struct denali_nand_info *denali, > return denali->irq_status; > } > > -/* resets a specific device connected to the core */ > -static void reset_bank(struct denali_nand_info *denali) > +static uint32_t denali_check_irq(struct denali_nand_info *denali) > { > + unsigned long flags; > uint32_t irq_status; > > - denali_reset_irq(denali); > - > - iowrite32(1 << denali->flash_bank, denali->flash_reg + DEVICE_RESET); > - > - irq_status = denali_wait_for_irq(denali, > - INTR__RST_COMP | INTR__TIME_OUT); > + spin_lock_irqsave(&denali->irq_lock, flags); > + irq_status = denali->irq_status; > + spin_unlock_irqrestore(&denali->irq_lock, flags); > > - if (!(irq_status & INTR__RST_COMP)) > - dev_err(denali->dev, "reset bank failed.\n"); > + return irq_status; > } > > /* > @@ -273,6 +269,42 @@ static uint8_t denali_read_byte(struct mtd_info *mtd) > return ioread32(denali->flash_mem + 0x10); > } > > +static void denali_write_byte(struct mtd_info *mtd, uint8_t byte) > +{ > + struct denali_nand_info *denali = mtd_to_denali(mtd); > + > + index_addr(denali, MODE_11 | BANK(denali->flash_bank) | 2, byte); > +} > + > +static void denali_cmd_ctrl(struct mtd_info *mtd, int dat, unsigned int ctrl) > +{ > + struct denali_nand_info *denali = mtd_to_denali(mtd); > + uint32_t type; > + > + if (ctrl & NAND_CLE) > + type = 0; > + else if (ctrl & NAND_ALE) > + type = 1; > + else > + return; > + > + /* > + * Some commands are followed by chip->dev_ready or chip->waitfunc. > + * irq_status must be cleared here to catch the R/B# interrupt later. > + */ > + if (ctrl & NAND_CTRL_CHANGE) > + denali_reset_irq(denali); > + > + index_addr(denali, MODE_11 | BANK(denali->flash_bank) | type, dat); > +} > + > +static int denali_dev_ready(struct mtd_info *mtd) > +{ > + struct denali_nand_info *denali = mtd_to_denali(mtd); > + > + return !!(denali_check_irq(denali) & INTR__INT_ACT); > +} > + > /* > * sends a pipeline command operation to the controller. See the Denali NAND > * controller's user guide for more information (section 4.2.3.6). > @@ -788,7 +820,13 @@ static void denali_select_chip(struct mtd_info *mtd, int chip) > > static int denali_waitfunc(struct mtd_info *mtd, struct nand_chip *chip) > { > - return 0; > + struct denali_nand_info *denali = mtd_to_denali(mtd); > + uint32_t irq_status; > + > + /* R/B# pin transitioned from low to high? */ > + irq_status = denali_wait_for_irq(denali, INTR__INT_ACT); > + > + return irq_status & INTR__INT_ACT ? 0 : NAND_STATUS_FAIL; > } > > static int denali_erase(struct mtd_info *mtd, int page) > @@ -809,46 +847,6 @@ static int denali_erase(struct mtd_info *mtd, int page) > return irq_status & INTR__ERASE_COMP ? 0 : NAND_STATUS_FAIL; > } > > -static void denali_cmdfunc(struct mtd_info *mtd, unsigned int cmd, int col, > - int page) > -{ > - struct denali_nand_info *denali = mtd_to_denali(mtd); > - uint32_t addr, irq_status; > - int wait_ready = 0; > - > - switch (cmd) { > - case NAND_CMD_PARAM: > - wait_ready = 1; > - break; > - case NAND_CMD_STATUS: > - case NAND_CMD_READID: > - break; > - case NAND_CMD_RESET: > - reset_bank(denali); > - break; > - case NAND_CMD_READOOB: > - /* TODO: Read OOB data */ > - return; > - default: > - pr_err(": unsupported command received 0x%x\n", cmd); > - return; > - } > - > - denali_reset_irq(denali); > - > - addr = MODE_11 | BANK(denali->flash_bank); > - index_addr(denali, addr | 0, cmd); > - if (col != -1) > - index_addr(denali, addr | 1, col); > - > - if (!wait_ready) > - return; > - > - irq_status = denali_wait_for_irq(denali, INTR__INT_ACT); > - if (!(irq_status & INTR__INT_ACT)) > - dev_err(denali->dev, "failed to issue command 0x%x\n", cmd); > -} > - > #define DIV_ROUND_DOWN_ULL(ll, d) \ > ({ unsigned long long _tmp = (ll); do_div(_tmp, d); _tmp; }) > > @@ -1187,8 +1185,10 @@ int denali_init(struct denali_nand_info *denali) > > /* register the driver with the NAND core subsystem */ > chip->select_chip = denali_select_chip; > - chip->cmdfunc = denali_cmdfunc; > chip->read_byte = denali_read_byte; > + chip->write_byte = denali_write_byte; > + chip->cmd_ctrl = denali_cmd_ctrl; > + chip->dev_ready = denali_dev_ready; > chip->waitfunc = denali_waitfunc; > /* clk rate info is needed for setup_data_interface */ > if (denali->clk_x_rate)