From: Ralf Baechle <ralf@linux-mips.org>
To: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org, linux-mtd@lists.infradead.org,
linux-watchdog@vger.kernel.org, devicetree@vger.kernel.org,
martin.blumenstingl@googlemail.com, john@phrozen.org,
linux-spi@vger.kernel.org, hauke.mehrtens@intel.com,
robh@kernel.org, andy.shevchenko@gmail.com,
p.zabel@pengutronix.de, kishon@ti.com, mark.rutland@arm.com,
Mark Brown <broonie@kernel.org>
Subject: Re: [PATCH v10 03/16] spi: spi-falcon: drop check of boot select
Date: Mon, 28 Aug 2017 13:23:27 +0200 [thread overview]
Message-ID: <20170828112327.GA15640@linux-mips.org> (raw)
In-Reply-To: <20170819221823.13850-4-hauke@hauke-m.de>
On Sun, Aug 20, 2017 at 12:18:10AM +0200, Hauke Mehrtens wrote:
> Do not check which flash type the SoC was booted from before
> using this driver. Assume that the device tree is correct and use this
> driver when it was added to device tree. This also removes a build
> dependency to the SoC code.
>
> All device trees I am aware of only have one correct flash device entry
> in it. The device tree is anyway bundled with the kernel in all systems
> using device tree I know of.
>
> The boot mode can be specified with some pin straps and will select the
> flash type the rom code will boot from. One SPI, NOR or NAND flash chip
> can be connect to the EBU and used to load the first stage boot loader
> from.
I think other than this patch we finally have all the acks necessary so
I merged the series except this patch which shouldn't be strictly necessary.
Ralf
next prev parent reply other threads:[~2017-08-28 11:24 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-08-19 22:18 [PATCH v10 00/16] MIPS: lantiq: handle RCU register by separate drivers Hauke Mehrtens
2017-08-19 22:18 ` [PATCH v10 01/16] MIPS: lantiq: Use of_platform_default_populate instead of __dt_register_buses Hauke Mehrtens
2017-08-19 22:18 ` [PATCH v10 02/16] mtd: lantiq-flash: drop check of boot select Hauke Mehrtens
2017-08-19 22:18 ` [PATCH v10 03/16] spi: spi-falcon: " Hauke Mehrtens
2017-08-28 11:23 ` Ralf Baechle [this message]
2017-08-28 11:29 ` Hauke Mehrtens
2017-08-29 18:33 ` Mark Brown
2017-08-19 22:18 ` [PATCH v10 04/16] watchdog: lantiq: access boot cause register through regmap Hauke Mehrtens
2017-08-19 22:18 ` [PATCH v10 05/16] watchdog: lantiq: add device tree binding documentation Hauke Mehrtens
2017-08-19 22:18 ` [PATCH v10 06/16] MIPS: lantiq: Enable MFD_SYSCON to be able to use it for the RCU MFD Hauke Mehrtens
2017-09-04 17:36 ` Martin Blumenstingl
2017-08-19 22:18 ` [PATCH v10 07/16] Documentation: DT: MIPS: lantiq: Add docs for the RCU bindings Hauke Mehrtens
2017-09-04 17:40 ` Martin Blumenstingl
2017-08-19 22:18 ` [PATCH v10 08/16] MIPS: lantiq: Convert the fpi bus driver to a platform_driver Hauke Mehrtens
2017-08-19 22:18 ` [PATCH v10 09/16] MIPS: lantiq: remove ltq_reset_cause() and ltq_boot_select() Hauke Mehrtens
2017-08-19 22:18 ` [PATCH v10 10/16] reset: Add a reset controller driver for the Lantiq XWAY based SoCs Hauke Mehrtens
2017-09-04 17:37 ` Martin Blumenstingl
2017-08-19 22:18 ` [PATCH v10 11/16] MIPS: lantiq: remove old reset controller implementation Hauke Mehrtens
2017-08-19 22:18 ` [PATCH v10 12/16] MIPS: lantiq: Add a GPHY driver which uses the RCU syscon-mfd Hauke Mehrtens
2017-09-04 17:39 ` Martin Blumenstingl
2017-08-19 22:18 ` [PATCH v10 13/16] MIPS: lantiq: remove old GPHY loader code Hauke Mehrtens
2017-08-19 22:18 ` [PATCH v10 14/16] phy: Add an USB PHY driver for the Lantiq SoCs using the RCU module Hauke Mehrtens
2017-08-19 22:18 ` [PATCH v10 15/16] MIPS: lantiq: remove old USB PHY initialisation Hauke Mehrtens
2017-08-19 22:18 ` [PATCH v10 16/16] MIPS: lantiq: Remove the arch/mips/lantiq/xway/reset.c implementation Hauke Mehrtens
2017-09-04 17:40 ` Martin Blumenstingl
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20170828112327.GA15640@linux-mips.org \
--to=ralf@linux-mips.org \
--cc=andy.shevchenko@gmail.com \
--cc=broonie@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=hauke.mehrtens@intel.com \
--cc=hauke@hauke-m.de \
--cc=john@phrozen.org \
--cc=kishon@ti.com \
--cc=linux-mips@linux-mips.org \
--cc=linux-mtd@lists.infradead.org \
--cc=linux-spi@vger.kernel.org \
--cc=linux-watchdog@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=martin.blumenstingl@googlemail.com \
--cc=p.zabel@pengutronix.de \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox