From: Boris Brezillon <boris.brezillon@bootlin.com>
To: thor.thayer@linux.intel.com
Cc: cyrille.pitchen@wedev4u.fr, marek.vasut@gmail.com,
dwmw2@infradead.org, computersforpeace@gmail.com, richard@nod.at,
linux-mtd@lists.infradead.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCHv2] mtd: spi-nor: Fix Cadence QSPI page fault kernel panic
Date: Fri, 20 Apr 2018 22:48:53 +0200 [thread overview]
Message-ID: <20180420224853.427d188e@bbrezillon> (raw)
In-Reply-To: <1522073537-27386-1-git-send-email-thor.thayer@linux.intel.com>
On Mon, 26 Mar 2018 09:12:17 -0500
thor.thayer@linux.intel.com wrote:
> From: Thor Thayer <thor.thayer@linux.intel.com>
>
> The current Cadence QSPI driver caused a kernel panic when loading
> a Root Filesystem from QSPI. The problem was caused by reading more
> bytes than needed because the QSPI operated on 4 bytes at a time.
> <snip>
> [ 7.947754] spi_nor_read[1048]:from 0x037cad74, len 1 [bfe07fff]
> [ 7.956247] cqspi_read[910]:offset 0x58502516, buffer=bfe07fff
> [ 7.956247]
> [ 7.966046] Unable to handle kernel paging request at virtual
> address bfe08002
> [ 7.973239] pgd = eebfc000
> [ 7.975931] [bfe08002] *pgd=2fffb811, *pte=00000000, *ppte=00000000
> </snip>
> Notice above how only 1 byte needed to be read but by reading 4 bytes
> into the end of a mapped page, an unrecoverable page fault occurred.
>
> This patch uses a temporary buffer to hold the 4 bytes read and then
> copies only the bytes required into the buffer. A min() function is
> used to limit the length to prevent buffer overflows.
>
> Request testing of this patch on other platforms. This was tested
> on the Intel Arria10 SoCFPGA DevKit.
>
> Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Can you add a Fixes and Cc-stable tag?
> ---
> v2 Changes to only write dangling bytes at end of transfer since
> previous patch may have multiple dangling byte transfers.
> Remove write patch since no errors reported and write timeout
> needs more investigation.
> ---
> drivers/mtd/spi-nor/cadence-quadspi.c | 19 +++++++++++++++++--
> 1 file changed, 17 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/mtd/spi-nor/cadence-quadspi.c b/drivers/mtd/spi-nor/cadence-quadspi.c
> index 4b8e9183489a..5872f31eaa60 100644
> --- a/drivers/mtd/spi-nor/cadence-quadspi.c
> +++ b/drivers/mtd/spi-nor/cadence-quadspi.c
> @@ -501,7 +501,9 @@ static int cqspi_indirect_read_execute(struct spi_nor *nor, u8 *rxbuf,
> void __iomem *reg_base = cqspi->iobase;
> void __iomem *ahb_base = cqspi->ahb_base;
> unsigned int remaining = n_rx;
> + unsigned int mod_bytes = n_rx % 4;
> unsigned int bytes_to_read = 0;
> + u8 *rxbuf_end = rxbuf + n_rx;
> int ret = 0;
>
> writel(from_addr, reg_base + CQSPI_REG_INDIRECTRDSTARTADDR);
> @@ -530,11 +532,24 @@ static int cqspi_indirect_read_execute(struct spi_nor *nor, u8 *rxbuf,
> }
>
> while (bytes_to_read != 0) {
> + unsigned int word_remain = round_down(remaining, 4);
> +
> bytes_to_read *= cqspi->fifo_width;
> bytes_to_read = bytes_to_read > remaining ?
> remaining : bytes_to_read;
> - ioread32_rep(ahb_base, rxbuf,
> - DIV_ROUND_UP(bytes_to_read, 4));
> + bytes_to_read = round_down(bytes_to_read, 4);
> + /* Read 4 byte word chunks then single bytes */
> + if (bytes_to_read) {
> + ioread32_rep(ahb_base, rxbuf,
> + (bytes_to_read / 4));
> + } else if (!word_remain && mod_bytes) {
> + unsigned int temp = ioread32(ahb_base);
> +
> + bytes_to_read = mod_bytes;
> + memcpy(rxbuf, &temp, min((unsigned int)
> + (rxbuf_end - rxbuf),
> + bytes_to_read));
> + }
> rxbuf += bytes_to_read;
> remaining -= bytes_to_read;
> bytes_to_read = cqspi_get_rd_sram_level(cqspi);
next prev parent reply other threads:[~2018-04-20 20:49 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-03-26 14:12 [PATCHv2] mtd: spi-nor: Fix Cadence QSPI page fault kernel panic thor.thayer
2018-04-11 15:17 ` Thor Thayer
2018-04-11 15:23 ` Marek Vasut
2018-04-20 20:48 ` Boris Brezillon [this message]
-- strict thread matches above, loose matches on Subject: below --
2018-11-16 14:25 thor.thayer
2018-11-20 8:02 ` Boris Brezillon
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180420224853.427d188e@bbrezillon \
--to=boris.brezillon@bootlin.com \
--cc=computersforpeace@gmail.com \
--cc=cyrille.pitchen@wedev4u.fr \
--cc=dwmw2@infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mtd@lists.infradead.org \
--cc=marek.vasut@gmail.com \
--cc=richard@nod.at \
--cc=thor.thayer@linux.intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox