Linux-mtd Archive on lore.kernel.org
 help / color / mirror / Atom feed
From: Miquel Raynal <miquel.raynal@bootlin.com>
To: Richard Weinberger <richard@nod.at>
Cc: Frieder Schrempf <frieder.schrempf@exceet.de>,
	linux-mtd@lists.infradead.org,
	Vignesh Raghavendra <vigneshr@ti.com>,
	Tudor Ambarus <Tudor.Ambarus@microchip.com>
Subject: [GIT PULL] mtd: nand: Changes for 5.3
Date: Fri, 5 Jul 2019 23:56:49 +0200	[thread overview]
Message-ID: <20190705235649.72b513b1@xps13> (raw)

Hello,

This is the NAND PR for 5.3.

Thanks,
Miquèl


The following changes since commit f2c7c76c5d0a443053e94adb9f0918fa2fb85c3a:

  Linux 5.2-rc3 (2019-06-02 13:55:33 -0700)

are available in the Git repository at:

  git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git tags/nand/for-5.3

for you to fetch changes up to bce9437a0a48dd5e19490f56e1cdc39a9be5563c:

  mtd: rawnand: stm32_fmc2: increase DMA completion timeouts (2019-06-28 12:01:53 +0200)

----------------------------------------------------------------
NAND core changes:
- use longest matching pattern in ->exec_op() default parser
- export NAND operation tracer
- add flag to indicate panic_write in MTD
- use kzalloc() instead of kmalloc() and memset()

Raw NAND controller drivers changes:
- brcmnand:
  * fix BCH ECC layout for large page NAND parts
  * fallback to detected ecc-strength, ecc-step-size
  * when oops in progress use pio and interrupt polling
  * code refactor code to introduce helper functions
  * add support for v7.3 controller
- FSMC:
  * use nand_op_trace for operation tracing
- GPMI:
  * move all driver code into single file
  * various cleanups (including dmaengine changes)
  * use runtime PM to manage clocks
  * implement exec_op
- MTK:
  * correct low level time calculation of r/w cycle
  * improve data sampling timing for read cycle
  * add validity check for CE# pin setting
  * fix wrongly assigned OOB buffer pointer issue
  * re-license MTK NAND driver as Dual MIT/GPL
- STM32:
  * manage the get_irq error case
  * increase DMA completion timeouts

Raw NAND chips drivers changes:
- Macronix: add read-retry support

Onenand driver changes:
- add support for 8Gb datasize chips
- avoid fall-through warnings

SPI-NAND changes:
- define macros for page-read ops with three-byte addresses
- add support for two-byte device IDs and then for GigaDevice
  GD5F1GQ4UFxxG
- add initial support for Paragon PN26G0xA
- handle the case where the last page read has bitflips

----------------------------------------------------------------
Amelie Delaunay (1):
      mtd: rawnand: stm32_fmc2: increase DMA completion timeouts

Colin Ian King (1):
      mtd: rawnand: gpmi: remove double assignment to block_size

Fabien Dessenne (1):
      mtd: rawnand: stm32_fmc2: manage the get_irq error case

Fuqian Huang (1):
      mtd: rawnand: Use kzalloc() instead of kmalloc() and memset()

Gustavo A. R. Silva (1):
      mtd: onenand: Avoid fall-through warnings

Jeff Kletsky (4):
      mtd: spinand: Define macros for page-read ops with three-byte addresses
      mtd: spinand: Add support for two-byte device IDs
      mtd: spinand: Add support for GigaDevice GD5F1GQ4UFxxG
      mtd: spinand: Add initial support for Paragon PN26G0xA

Jonathan Bakker (1):
      mtd: onenand: Add support for 8Gb datasize onenand

Kamal Dasu (8):
      mtd: rawnand: brcmnand: Fix BCH ECC layout for large page NAND parts
      dt-bindings: mtd: brcmnand: Make nand-ecc-strength and nand-ecc-step-size optional
      mtd: rawnand: brcmnand: fallback to detected ecc-strength, ecc-step-size
      mtd: Add flag to indicate panic_write
      mtd: rawnand: brcmnand: When oops in progress use pio and interrupt polling
      mtd: rawnand: brcmnand: Refactored code to introduce helper functions
      mtd: rawnand: brcmnand: Add support for v7.3 controller
      dt-bindings: mtd: brcmnand: Add brcmnand, brcmnand-v7.3 support

Mason Yang (1):
      mtd: rawnand: Add Macronix NAND read retry support

Sascha Hauer (14):
      mtd: rawnand: export NAND operation tracer
      mtd: rawnand: fsmc: Use nand_op_trace for operation tracing
      mtd: rawnand: gpmi: move all driver code into single file
      mtd: rawnand: gpmi: remove unused variable
      mtd: rawnand: gpmi: Remove unnecessary variables
      mtd: rawnand: gpmi: read buf in nand_read_page_op
      mtd: rawnand: gpmi: remove unused parameters
      mtd: rawnand: gpmi: Drop unnecessary restoring of previous chipselection
      mtd: rawnand: gpmi: use runtime PM to manage clocks
      dmaengine: mxs: Drop unnecessary flag
      mtd: rawnand: gpmi: drop unnecessary flag
      dmaengine: mxs: Add header file to be shared with gpmi nand driver
      dmaengine: mxs: rename custom flag
      mtd: rawnand: gpmi: Implement exec_op

Stefan Agner (1):
      mtd: rawnand: use longest matching pattern

Xiaolei Li (5):
      mtd: rawnand: mtk: Correct low level time calculation of r/w cycle
      mtd: rawnand: mtk: Improve data sampling timing for read cycle
      mtd: rawnand: mtk: Add validity check for CE# pin setting
      mtd: rawnand: mtk: Fix wrongly assigned OOB buffer pointer issue
      mtd: rawnand: mtk: Re-license MTK NAND driver as Dual MIT/GPL

liaoweixiong (1):
      mtd: spinand: read returns badly if the last page has bitflips

 Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt |    5 +-
 drivers/dma/mxs-dma.c                                   |   25 +-
 drivers/mtd/mtdcore.c                                   |    3 +
 drivers/mtd/nand/onenand/onenand_base.c                 |    5 +
 drivers/mtd/nand/raw/brcmnand/brcmnand.c                |  263 +++-
 drivers/mtd/nand/raw/fsmc_nand.c                        |   19 +-
 drivers/mtd/nand/raw/gpmi-nand/Makefile                 |    1 -
 drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c               |  934 ------------
 drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c              | 1731 +++++++++++++++-------
 drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.h              |   64 +-
 drivers/mtd/nand/raw/mtk_ecc.c                          |    4 +-
 drivers/mtd/nand/raw/mtk_ecc.h                          |    4 +-
 drivers/mtd/nand/raw/mtk_nand.c                         |   88 +-
 drivers/mtd/nand/raw/nand_base.c                        |   80 +-
 drivers/mtd/nand/raw/nand_bch.c                         |    3 +-
 drivers/mtd/nand/raw/nand_macronix.c                    |   45 +
 drivers/mtd/nand/raw/stm32_fmc2_nand.c                  |   21 +-
 drivers/mtd/nand/spi/Makefile                           |    2 +-
 drivers/mtd/nand/spi/core.c                             |    5 +-
 drivers/mtd/nand/spi/gigadevice.c                       |   81 +-
 drivers/mtd/nand/spi/paragon.c                          |  147 ++
 include/linux/dma/mxs-dma.h                             |   24 +
 include/linux/mtd/mtd.h                                 |    6 +
 include/linux/mtd/onenand_regs.h                        |    1 +
 include/linux/mtd/rawnand.h                             |   36 +
 include/linux/mtd/spinand.h                             |   35 +-
 26 files changed, 1935 insertions(+), 1697 deletions(-)
 delete mode 100644 drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c
 create mode 100644 drivers/mtd/nand/spi/paragon.c
 create mode 100644 include/linux/dma/mxs-dma.h

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

             reply	other threads:[~2019-07-05 21:58 UTC|newest]

Thread overview: 2+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-07-05 21:56 Miquel Raynal [this message]
2019-07-06 20:53 ` [GIT PULL] mtd: nand: Changes for 5.3 Richard Weinberger

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190705235649.72b513b1@xps13 \
    --to=miquel.raynal@bootlin.com \
    --cc=Tudor.Ambarus@microchip.com \
    --cc=frieder.schrempf@exceet.de \
    --cc=linux-mtd@lists.infradead.org \
    --cc=richard@nod.at \
    --cc=vigneshr@ti.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox