From: Boris Brezillon <boris.brezillon@collabora.com>
To: Greg Ungerer <gerg@kernel.org>
Cc: s.hauer@pengutronix.de, Boris Brezillon <bbrezillon@kernel.org>,
linux-mtd@lists.infradead.org,
Michael Nazzareno Trimarchi <michael@amarulasolutions.com>,
Miquel Raynal <miquel.raynal@bootlin.com>
Subject: Re: GPMI iMX6ull timeout on DMA
Date: Wed, 31 Jul 2019 08:28:23 +0200 [thread overview]
Message-ID: <20190731082823.6284f5a9@collabora.com> (raw)
In-Reply-To: <0a6afd79-d5ca-24da-a62c-11146a3522f6@kernel.org>
On Wed, 31 Jul 2019 12:05:44 +1000
Greg Ungerer <gerg@kernel.org> wrote:
> Hi Miquel, Boris,
>
> On 30/7/19 6:38 pm, Miquel Raynal wrote:
> > Greg Ungerer <gerg@kernel.org> wrote on Tue, 30 Jul 2019 16:06:55 +1000:
> >> On 30/7/19 10:41 am, Greg Ungerer wrote:
> >>> On 30/7/19 10:28 am, Greg Ungerer wrote:
> >>>> On 29/7/19 10:47 pm, Miquel Raynal wrote:
> >>>>> Greg Ungerer <gerg@kernel.org> wrote on Mon, 29 Jul 2019 22:33:56 +1000:
> >>>>>> On 29/7/19 6:36 pm, Miquel Raynal wrote:
> >>>>>>> Greg Ungerer <gerg@kernel.org> wrote on Mon, 29 Jul 2019 16:41:51 +1000:
> >>> [snip]
> >> Not sure if this is a useful data point... But I modified that
> >> nand_init_data_interface() loop to start checking from data mode 4.
> >> So now on every boot it defaults to mode 4. That has been running
> >> most of the day, up to 900 boot cycles now, no failures.
> >
> > Ok so after having chatted quite a bit with Boris, it is very likely
> > that, for these chips, the timings in mode 5 are too tight. It could
> > fail the GET_FEATURES once in mode 5. Can you please dump every single
> > intermediate value in gpmi_nfc_compute_timings() (period, *_cycles,
> > use of half pêriods, tRP, sample delay, etc) as well as the content
> > of /sys/kernel/debug/clk/clk_summary (you'll need debugfs support
> > enabled and mounted).
> >
> > Also, can you be sure that the NAND chip is powered with 3.3V?
>
> Yes, 3.3V NAND chip.
>
> Using the attached patch I get the following trace:
>
> ...
> drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c(426): gpmi_nfc_compute_timings()
> sdr->tBERS_max=65535000000
> sdr->tCCS_min=500000000
> sdr->tPROG_max=65535000000
> sdr->tR_max=200000000000000
> sdr->tALH_min=20000
> sdr->tADL_min=400000
> sdr->tALS_min=50000
> sdr->tAR_min=25000
> sdr->tCEA_max=100000
> sdr->tCEH_min=20000
> sdr->tCH_min=20000
> sdr->tCHZ_max=100000
> sdr->tCLH_min=20000
> sdr->tCLR_min=20000
> sdr->tCLS_min=50000
> sdr->tCOH_min=0
> sdr->tCS_min=70000
> sdr->tDH_min=20000
> sdr->tDS_min=40000
> sdr->tFEAT_max=1000000
> sdr->tIR_min=10000
> sdr->tITC_max=1000000
> sdr->tRC_min=100000
> sdr->tREA_max=40000
> sdr->tREH_min=30000
> sdr->tRHOH_min=0
> sdr->tRHW_min=200000
> sdr->tRHZ_max=200000
> sdr->tRLOH_min=0
> sdr->tRP_min=50000
> sdr->tRR_min=40000
> sdr->tRST_max=250000000000
> sdr->tWB_max=200000
> sdr->tWC_min=100000
> sdr->tWH_min=30000
> sdr->tWHR_min=120000
> sdr->tWP_min=50000
> sdr->tWW_min=100000
> hw->clk_rate=22000000
> wrn_dly_sel=0
> period_ps=45454
> addr_setup_cycles=2
> data_setup_cycles=1
> data_hold_cycles=1
> busy_timeout_cycles=31302
> hw->timing0=0x00020101
> hw->timing1=0x60000000
> dll_threshold_ps=12000
> use_half_period=1
> reference_period_ps=22727
> tRP_ps=45454
> sample_delay_ps=4294955664
> sample_delay_factor=0
> hw->ctrl1n=0x00000000
> hw->ctrl1n=0x00000000
> drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c(547): gpmi_nfc_apply_timings()
> hw>clk_rate=22000000
> clk_set_rate(r->clock[0], hw->clk_rate)=0
> clk_get_rate(r->clock[0])=22000000
> random: fast init done
> nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
> nand: Micron MT29F2G08ABAEAWP
> nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
> drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c(426): gpmi_nfc_compute_timings()
> sdr->tBERS_max=3000000000
> sdr->tCCS_min=100000
> sdr->tPROG_max=600000000
> sdr->tR_max=25000000
> sdr->tALH_min=20000
> sdr->tADL_min=400000
> sdr->tALS_min=50000
> sdr->tAR_min=25000
> sdr->tCEA_max=100000
> sdr->tCEH_min=20000
> sdr->tCH_min=20000
> sdr->tCHZ_max=100000
> sdr->tCLH_min=20000
> sdr->tCLR_min=20000
> sdr->tCLS_min=50000
> sdr->tCOH_min=0
> sdr->tCS_min=70000
> sdr->tDH_min=20000
> sdr->tDS_min=40000
> sdr->tFEAT_max=1000000
> sdr->tIR_min=10000
> sdr->tITC_max=1000000
> sdr->tRC_min=100000
> sdr->tREA_max=40000
> sdr->tREH_min=30000
> sdr->tRHOH_min=0
> sdr->tRHW_min=200000
> sdr->tRHZ_max=200000
> sdr->tRLOH_min=0
> sdr->tRP_min=50000
> sdr->tRR_min=40000
> sdr->tRST_max=250000000000
> sdr->tWB_max=200000
> sdr->tWC_min=100000
> sdr->tWH_min=30000
> sdr->tWHR_min=120000
> sdr->tWP_min=50000
> sdr->tWW_min=100000
> hw->clk_rate=22000000
> wrn_dly_sel=0
> period_ps=45454
> addr_setup_cycles=2
> data_setup_cycles=1
> data_hold_cycles=1
> busy_timeout_cycles=555
> hw->timing0=0x00020101
> hw->timing1=0xb0000000
> dll_threshold_ps=12000
> use_half_period=1
> reference_period_ps=22727
> tRP_ps=45454
> sample_delay_ps=4294955664
> sample_delay_factor=0
> hw->ctrl1n=0x00000000
> hw->ctrl1n=0x00000000
> drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c(547): gpmi_nfc_apply_timings()
> hw>clk_rate=22000000
> clk_set_rate(r->clock[0], hw->clk_rate)=0
> clk_get_rate(r->clock[0])=22000000
> gpmi-nand 1806000.gpmi-nand: use legacy bch geometry
> drivers/mtd/nand/raw/nand_base.c(913): checking mode=5
> drivers/mtd/nand/raw/nand_base.c(927): BREAKING AT mode=5
> drivers/mtd/nand/raw/nand_base.c(932): chip->onfi_timing_mode_default=5
> drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c(426): gpmi_nfc_compute_timings()
> sdr->tBERS_max=3000000000
> sdr->tCCS_min=100000
> sdr->tPROG_max=600000000
> sdr->tR_max=25000000
> sdr->tALH_min=5000
> sdr->tADL_min=400000
> sdr->tALS_min=10000
> sdr->tAR_min=10000
> sdr->tCEA_max=25000
> sdr->tCEH_min=20000
> sdr->tCH_min=5000
> sdr->tCHZ_max=30000
> sdr->tCLH_min=5000
> sdr->tCLR_min=10000
> sdr->tCLS_min=10000
> sdr->tCOH_min=15000
> sdr->tCS_min=15000
> sdr->tDH_min=5000
> sdr->tDS_min=7000
> sdr->tFEAT_max=1000000
> sdr->tIR_min=0
> sdr->tITC_max=1000000
> sdr->tRC_min=20000
> sdr->tREA_max=16000
> sdr->tREH_min=7000
> sdr->tRHOH_min=15000
> sdr->tRHW_min=100000
> sdr->tRHZ_max=100000
> sdr->tRLOH_min=5000
> sdr->tRP_min=10000
> sdr->tRR_min=20000
> sdr->tRST_max=500000000
> sdr->tWB_max=100000
> sdr->tWC_min=20000
> sdr->tWH_min=7000
> sdr->tWHR_min=80000
> sdr->tWP_min=10000
> sdr->tWW_min=100000
> hw->clk_rate=100000000
> wrn_dly_sel=3
> period_ps=10000
> addr_setup_cycles=1
> data_setup_cycles=1
> data_hold_cycles=1
> busy_timeout_cycles=2510
> hw->timing0=0x00010101
> hw->timing1=0xe0000000
> dll_threshold_ps=12000
> use_half_period=0
> reference_period_ps=10000
> tRP_ps=10000
> sample_delay_ps=80000
> sample_delay_factor=8
> hw->ctrl1n=0x00c00000
> hw->ctrl1n=0x00c28000
> drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c(547): gpmi_nfc_apply_timings()
> hw>clk_rate=100000000
> clk_set_rate(r->clock[0], hw->clk_rate)=0
> clk_get_rate(r->clock[0])=99000000
> Scanning device for bad blocks
> 5 fixed-partitions partitions found on MTD device gpmi-nand
> Creating 5 MTD partitions on "gpmi-nand":
> 0x000000000000-0x000000500000 : "u-boot"
> 0x000000500000-0x000000600000 : "u-boot-env"
> 0x000000600000-0x000000800000 : "log"
> 0x000000800000-0x000010000000 : "flash"
> 0x000000000000-0x000010000000 : "all"
> gpmi-nand 1806000.gpmi-nand: driver registered.
> ...
>
>
> And "cat /sys/kernel/debug/clk/clk_summary" gives:
>
> enable prepare protect duty
> clock count count count rate accuracy phase cycle
> ---------------------------------------------------------------------------------------------
> dummy 2 2 0 0 0 0 50000
> cko2_sel 0 0 0 0 0 0 50000
> cko2_podf 0 0 0 0 0 0 50000
> cko2 0 0 0 0 0 0 50000
> cko1_sel 0 0 0 0 0 0 50000
> cko1_podf 0 0 0 0 0 0 50000
> cko1 0 0 0 0 0 0 50000
> cko 0 0 0 0 0 0 50000
> usbphy2_gate 1 1 0 0 0 0 50000
> usbphy1_gate 1 1 0 0 0 0 50000
> ipp_di1 0 0 0 0 0 0 50000
> ipp_di0 0 0 0 0 0 0 50000
> osc 6 6 0 24000000 0 0 50000
> perclk_sel 1 1 0 24000000 0 0 50000
> perclk 3 3 0 24000000 0 0 50000
> pwm7 0 0 0 24000000 0 0 50000
> pwm6 0 0 0 24000000 0 0 50000
> pwm5 0 0 0 24000000 0 0 50000
> i2c4 0 0 0 24000000 0 0 50000
> pwm8 0 0 0 24000000 0 0 50000
> pwm4 0 0 0 24000000 0 0 50000
> pwm3 0 0 0 24000000 0 0 50000
> pwm2 0 0 0 24000000 0 0 50000
> pwm1 0 0 0 24000000 0 0 50000
> i2c3 0 0 0 24000000 0 0 50000
> i2c2 1 1 0 24000000 0 0 50000
> i2c1 0 0 0 24000000 0 0 50000
> gpt1_serial 1 1 0 24000000 0 0 50000
> gpt1_bus 1 1 0 24000000 0 0 50000
> epit2 0 0 0 24000000 0 0 50000
> epit1 0 0 0 24000000 0 0 50000
> gpt2_serial 0 0 0 24000000 0 0 50000
> gpt2_bus 0 0 0 24000000 0 0 50000
> periph_clk2_sel 0 0 0 24000000 0 0 50000
> periph_clk2 0 0 0 24000000 0 0 50000
> gpt_3m 0 0 0 3000000 0 0 50000
> csi_sel 0 0 0 24000000 0 0 50000
> csi_podf 0 0 0 24000000 0 0 50000
> csi 0 0 0 24000000 0 0 50000
> pll7 1 1 0 480000000 0 0 50000
> pll7_bypass 1 1 0 480000000 0 0 50000
> pll7_usb_host 1 1 0 480000000 0 0 50000
> usbphy2 1 1 0 480000000 0 0 50000
> pll6 1 1 0 500000000 0 0 50000
> pll6_bypass 1 1 0 500000000 0 0 50000
> pll6_enet 2 2 0 500000000 0 0 50000
> enet_ptp_ref 1 1 0 25000000 0 0 50000
> enet_ptp 1 1 0 25000000 0 0 50000
> enet2_ref 0 0 0 50000000 0 0 50000
> enet_ref_125m 0 0 0 50000000 0 0 50000
> enet_ref 2 2 0 50000000 0 0 50000
> pll5 0 0 0 296600000 0 0 50000
> pll5_bypass 0 0 0 296600000 0 0 50000
> pll5_video 0 0 0 296600000 0 0 50000
> pll5_post_div 0 0 0 74150000 0 0 50000
> pll5_video_div 0 0 0 74150000 0 0 50000
> pll4 0 0 0 147456000 0 0 50000
> pll4_bypass 0 0 0 147456000 0 0 50000
> pll4_audio 0 0 0 147456000 0 0 50000
> pll4_post_div 0 0 0 36864000 0 0 50000
> pll4_audio_div 0 0 0 36864000 0 0 50000
> pll3 1 1 0 480000000 0 0 50000
> pll3_bypass 1 1 0 480000000 0 0 50000
> pll3_usb_otg 2 2 0 480000000 0 0 50000
> spdif_sel 0 0 0 480000000 0 0 50000
> spdif_pred 0 0 0 240000000 0 0 50000
> spdif_podf 0 0 0 30000000 0 0 50000
> spdif 0 0 0 30000000 0 0 50000
> esai_sel 0 0 0 480000000 0 0 50000
> esai_pred 0 0 0 240000000 0 0 50000
> esai_podf 0 0 0 30000000 0 0 50000
> esai_extal 0 0 0 30000000 0 0 50000
> qspi1_sel 0 0 0 480000000 0 0 50000
> qspi1_podf 0 0 0 240000000 0 0 50000
> qspi1 0 0 0 240000000 0 0 50000
> ldb_di1_div_7 0 0 0 68571428 0 0 50000
> ldb_di1 0 0 0 68571428 0 0 50000
> ldb_di1_div_3_5 0 0 0 137142857 0 0 50000
> periph2_clk2_sel 0 0 0 480000000 0 0 50000
> periph2_clk2 0 0 0 480000000 0 0 50000
> pll3_60m 0 0 0 60000000 0 0 50000
> can_sel 0 0 0 60000000 0 0 50000
> can_podf 0 0 0 30000000 0 0 50000
> can2_serial 0 0 0 30000000 0 0 50000
> can1_serial 0 0 0 30000000 0 0 50000
> ecspi_sel 0 0 0 60000000 0 0 50000
> ecspi_podf 0 0 0 60000000 0 0 50000
> ecspi4 0 0 0 60000000 0 0 50000
> ecspi3 0 0 0 60000000 0 0 50000
> ecspi2 0 0 0 60000000 0 0 50000
> ecspi1 0 0 0 60000000 0 0 50000
> pll3_80m 1 1 0 80000000 0 0 50000
> uart_sel 1 1 0 80000000 0 0 50000
> uart_podf 1 1 0 80000000 0 0 50000
> uart8_serial 0 0 0 80000000 0 0 50000
> uart7_serial 0 0 0 80000000 0 0 50000
> uart1_serial 1 2 0 80000000 0 0 50000
> uart6_serial 0 0 0 80000000 0 0 50000
> uart5_serial 0 0 0 80000000 0 0 50000
> uart4_serial 0 0 0 80000000 0 0 50000
> uart3_serial 0 0 0 80000000 0 0 50000
> uart2_serial 0 0 0 80000000 0 0 50000
> pll3_pfd3_454m 0 0 0 454736842 0 0 50000
> pll3_pfd2_508m 0 0 0 508235294 0 0 50000
> epdc_pre_sel 0 0 0 508235294 0 0 50000
> epdc_podf 0 0 0 254117647 0 0 50000
> epdc_pix 0 0 0 254117647 0 0 50000
> epdc_sel 0 0 0 254117647 0 0 50000
> sai1_sel 0 0 0 508235294 0 0 50000
> sai1_pred 0 0 0 127058824 0 0 50000
> sai1_podf 0 0 0 63529412 0 0 50000
> sai1 0 0 0 63529412 0 0 50000
> sai2_sel 0 0 0 508235294 0 0 50000
> sai2_pred 0 0 0 127058824 0 0 50000
> sai2_podf 0 0 0 63529412 0 0 50000
> sai2 0 0 0 63529412 0 0 50000
> sai3_sel 0 0 0 508235294 0 0 50000
> sai3_pred 0 0 0 127058824 0 0 50000
> sai3_podf 0 0 0 63529412 0 0 50000
> sai3 0 0 0 63529412 0 0 50000
> pll3_pfd1_540m 0 0 0 540000000 0 0 50000
> lcdif_pre_sel 0 0 0 540000000 0 0 50000
> lcdif_pred 0 0 0 270000000 0 0 50000
> lcdif_podf 0 0 0 135000000 0 0 50000
> lcdif_pix 0 0 0 135000000 0 0 50000
> iomuxc 0 0 0 135000000 0 0 50000
> lcdif_sel 0 0 0 135000000 0 0 50000
> pll3_pfd0_720m 0 0 0 720000000 0 0 50000
> usbphy1 1 1 0 480000000 0 0 50000
> pll2 1 1 0 528000000 0 0 50000
> pll2_bypass 1 1 0 528000000 0 0 50000
> pll2_bus 2 2 0 528000000 0 0 50000
> ca7_secondary_sel 0 0 0 528000000 0 0 50000
> step 0 0 0 528000000 0 0 50000
> periph_pre 1 1 0 528000000 0 0 50000
> periph 3 3 0 528000000 0 0 50000
> ahb 7 7 0 132000000 0 0 50000
> sdma 0 0 0 132000000 0 0 50000
> rom 1 1 0 132000000 0 0 50000
> esai_mem 0 0 0 132000000 0 0 50000
> esai_ipg 0 0 0 132000000 0 0 50000
> aips_tz3 1 1 0 132000000 0 0 50000
> enet_ahb 2 2 0 132000000 0 0 50000
> dcp 0 0 0 132000000 0 0 50000
> asrc_mem 0 0 0 132000000 0 0 50000
> asrc_ipg 0 0 0 132000000 0 0 50000
> aips_tz2 1 1 0 132000000 0 0 50000
> aips_tz1 1 1 0 132000000 0 0 50000
> ipg 10 10 0 66000000 0 0 50000
> wdog3 0 0 0 66000000 0 0 50000
> uart8_ipg 0 0 0 66000000 0 0 50000
> usboh3 2 2 0 66000000 0 0 50000
> sai2_ipg 0 0 0 66000000 0 0 50000
> sai1_ipg 0 0 0 66000000 0 0 50000
> uart7_ipg 0 0 0 66000000 0 0 50000
> uart1_ipg 1 2 0 66000000 0 0 50000
> sai3_ipg 0 0 0 66000000 0 0 50000
> spdif_gclk 0 0 0 66000000 0 0 50000
> spba 0 0 0 66000000 0 0 50000
> wdog2 0 0 0 66000000 0 0 50000
> kpp 0 0 0 66000000 0 0 50000
> mmdc_p1_ipg 0 0 0 66000000 0 0 50000
> mmdc_p0_ipg 2 2 0 66000000 0 0 50000
> wdog1 1 1 0 66000000 0 0 50000
> gpio4 1 1 0 66000000 0 0 50000
> uart6_ipg 0 0 0 66000000 0 0 50000
> uart5_ipg 0 0 0 66000000 0 0 50000
> gpio3 1 1 0 66000000 0 0 50000
> ocotp 0 0 0 66000000 0 0 50000
> gpio5 1 1 0 66000000 0 0 50000
> gpio1 1 1 0 66000000 0 0 50000
> uart4_ipg 0 0 0 66000000 0 0 50000
> adc1 0 0 0 66000000 0 0 50000
> uart3_ipg 0 0 0 66000000 0 0 50000
> adc2 0 0 0 66000000 0 0 50000
> gpio2 1 1 0 66000000 0 0 50000
> uart2_ipg 0 0 0 66000000 0 0 50000
> can2_ipg 0 0 0 66000000 0 0 50000
> can1_ipg 0 0 0 66000000 0 0 50000
> enet 2 2 0 66000000 0 0 50000
> axi_sel 1 1 0 528000000 0 0 50000
> axi_podf 2 2 0 264000000 0 0 50000
> axi 1 1 0 264000000 0 0 50000
> eim_slow_sel 0 0 0 264000000 0 0 50000
> eim_slow_podf 0 0 0 132000000 0 0 50000
> eim 0 0 0 132000000 0 0 50000
> lcdif_apb 0 0 0 264000000 0 0 50000
> pxp 0 0 0 264000000 0 0 50000
> epdc_aclk 0 0 0 264000000 0 0 50000
> pll2_pfd3_594m 0 0 0 594000000 0 0 50000
> ldb_di0_sel 0 0 0 594000000 0 0 50000
> ldb_di0_div_7 0 0 0 84857142 0 0 50000
> ldb_di0 0 0 0 84857142 0 0 50000
> ldb_di0_div_3_5 0 0 0 169714285 0 0 50000
> pll2_pfd2_396m 2 2 0 396000000 0 0 50000
> enfc_sel 0 0 0 396000000 0 0 50000
> enfc_pred 0 0 0 99000000 0 0 50000
> enfc_podf 0 0 0 99000000 0 0 50000
> gpmi_io 0 0 0 99000000 0 0 50000
> usdhc1_sel 0 0 0 396000000 0 0 50000
> usdhc1_podf 0 0 0 198000000 0 0 50000
> usdhc1 0 0 0 198000000 0 0 50000
> usdhc2_sel 0 0 0 396000000 0 0 50000
> usdhc2_podf 0 0 0 198000000 0 0 50000
> usdhc2 0 0 0 198000000 0 0 50000
> bch_sel 1 1 0 396000000 0 0 50000
> bch_podf 1 1 0 99000000 0 0 50000
> gpmi_apb 0 0 0 99000000 0 0 50000
> gpmi_bch_apb 0 0 0 99000000 0 0 50000
> per_bch 0 0 0 99000000 0 0 50000
> apbh_dma 1 1 0 99000000 0 0 50000
> gpmi_sel 0 0 0 396000000 0 0 50000
> gpmi_podf 0 0 0 99000000 0 0 50000
> gpmi_bch 0 0 0 99000000 0 0 50000
> periph2_pre 1 1 0 396000000 0 0 50000
> periph2 2 2 0 396000000 0 0 50000
> mmdc_podf 2 2 0 396000000 0 0 50000
> mmdc_p0_fast 1 1 0 396000000 0 0 50000
> axi_alt_sel 0 0 0 396000000 0 0 50000
> pll2_198m 0 0 0 198000000 0 0 50000
> pll2_pfd1_594m 0 0 0 594000000 0 0 50000
> pll2_pfd0_352m 0 0 0 352000000 0 0 50000
> pll1 1 1 0 900000000 0 0 50000
> pll1_bypass 1 1 0 900000000 0 0 50000
> pll1_sys 1 1 0 900000000 0 0 50000
> pll1_sw 1 1 0 900000000 0 0 50000
> arm 1 1 0 900000000 0 0 50000
> pll7_bypass_src 0 0 0 24000000 0 0 50000
> pll6_bypass_src 0 0 0 24000000 0 0 50000
> pll5_bypass_src 0 0 0 24000000 0 0 50000
> pll4_bypass_src 0 0 0 24000000 0 0 50000
> pll3_bypass_src 0 0 0 24000000 0 0 50000
> pll2_bypass_src 0 0 0 24000000 0 0 50000
> pll1_bypass_src 0 0 0 24000000 0 0 50000
> ckil 0 0 0 32768 0 0 50000
>
>
> Note that this was generated on a normal boot up (not failure).
The values looks good. Can you try with the below diff applied?
--->8---
diff --git a/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c b/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c
index 334fe3130285..9771f6a82abe 100644
--- a/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c
+++ b/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c
@@ -721,12 +721,10 @@ static void gpmi_nfc_apply_timings(struct gpmi_nand_data *this)
writel(hw->ctrl1n, gpmi_regs + HW_GPMI_CTRL1_SET);
/* Wait 64 clock cycles before using the GPMI after enabling the DLL */
- dll_wait_time_us = USEC_PER_SEC / hw->clk_rate * 64;
- if (!dll_wait_time_us)
- dll_wait_time_us = 1;
+ dll_wait_time_us = DIV_ROUND_UP(USEC_PER_SEC * 64, hw->clk_rate);
/* Wait for the DLL to settle. */
- udelay(dll_wait_time_us);
+ usleep_range(dll_wait_time_us, dll_wait_time_us * 10);
}
static int gpmi_setup_data_interface(struct nand_chip *chip, int chipnr,
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
next prev parent reply other threads:[~2019-07-31 6:28 UTC|newest]
Thread overview: 85+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-07-29 6:41 GPMI iMX6ull timeout on DMA Greg Ungerer
2019-07-29 8:36 ` Miquel Raynal
2019-07-29 8:42 ` Michael Nazzareno Trimarchi
2019-07-29 12:18 ` Greg Ungerer
2019-07-29 12:20 ` Michael Nazzareno Trimarchi
2019-07-29 12:33 ` Greg Ungerer
2019-07-29 12:47 ` Miquel Raynal
2019-07-29 12:49 ` Michael Nazzareno Trimarchi
2019-07-29 12:55 ` Miquel Raynal
2019-07-29 13:00 ` Michael Nazzareno Trimarchi
2019-07-29 13:22 ` Miquel Raynal
2019-07-29 20:00 ` Michael Nazzareno Trimarchi
2019-07-29 21:02 ` Miquel Raynal
2019-07-30 0:28 ` Greg Ungerer
2019-07-30 0:41 ` Greg Ungerer
2019-07-30 6:06 ` Greg Ungerer
2019-07-30 8:38 ` Miquel Raynal
2019-07-30 8:58 ` Boris Brezillon
2019-07-31 2:05 ` Greg Ungerer
2019-07-31 6:28 ` Boris Brezillon [this message]
2019-08-02 7:19 ` Greg Ungerer
2019-08-02 12:34 ` Greg Ungerer
2019-08-02 12:51 ` Boris Brezillon
2019-08-05 5:51 ` Greg Ungerer
2019-08-07 16:05 ` Miquel Raynal
2019-08-08 0:43 ` Greg Ungerer
2019-08-08 16:36 ` Boris Brezillon
2019-08-09 5:20 ` Greg Ungerer
2019-08-09 6:23 ` Boris Brezillon
2019-08-09 6:55 ` Greg Ungerer
2019-08-09 7:32 ` Boris Brezillon
2019-08-09 13:57 ` Greg Ungerer
2019-08-09 13:59 ` Boris Brezillon
2019-08-12 2:50 ` Greg Ungerer
2019-08-12 4:04 ` Greg Ungerer
2019-08-12 7:31 ` Boris Brezillon
2019-08-13 0:50 ` Greg Ungerer
2021-01-28 9:45 ` Michael Nazzareno Trimarchi
2021-01-28 10:26 ` Miquel Raynal
2021-01-28 10:35 ` Michael Nazzareno Trimarchi
2021-01-28 11:55 ` Michael Nazzareno Trimarchi
2021-01-29 12:43 ` Greg Ungerer
2021-01-30 9:41 ` Michael Nazzareno Trimarchi
2021-02-01 14:13 ` Miquel Raynal
2021-02-01 14:32 ` Michael Nazzareno Trimarchi
2021-02-01 15:08 ` Michael Nazzareno Trimarchi
2021-02-01 15:14 ` Miquel Raynal
2021-02-01 15:17 ` Michael Nazzareno Trimarchi
2021-10-15 20:05 ` Michael Trimarchi
2021-10-15 20:12 ` Michael Nazzareno Trimarchi
2021-10-18 7:19 ` Miquel Raynal
2021-10-18 7:33 ` Michael Nazzareno Trimarchi
2021-10-18 7:43 ` Miquel Raynal
2021-10-04 5:54 ` Christian Eggers
2021-10-04 6:27 ` Michael Nazzareno Trimarchi
2021-10-04 15:33 ` Miquel Raynal
2021-10-04 16:06 ` Han Xu
2021-10-05 6:02 ` Christian Eggers
2021-10-08 9:55 ` Christian Eggers
2021-10-08 12:08 ` Stefan Riedmüller
2021-10-08 12:27 ` Miquel Raynal
2021-10-08 13:11 ` Christian Eggers
2021-10-08 13:29 ` Miquel Raynal
2021-10-08 13:36 ` Miquel Raynal
2021-10-08 13:49 ` Christian Eggers
2021-10-08 16:07 ` Miquel Raynal
2021-10-09 5:53 ` Michael Nazzareno Trimarchi
2021-10-11 6:46 ` Miquel Raynal
2021-10-12 9:02 ` [RFC PATCH 1/2] mtd: rawnand: gpmi: Remove explicit default gpmi clock setting for i.MX6 Stefan Riedmueller
2021-10-12 9:02 ` [RFC PATCH 2/2] gpmi-nand: Add ERR007117 protection for nfc_apply_timings Stefan Riedmueller
2021-10-13 5:01 ` Han Xu
2021-10-22 8:45 ` Stefan Riedmüller
2021-10-22 14:35 ` han.xu
2021-10-25 9:39 ` Stefan Riedmüller
2021-10-28 9:28 ` Stefan Riedmüller
2021-11-01 4:01 ` han.xu
2021-10-13 6:10 ` Christian Eggers
2021-10-13 6:00 ` [RFC PATCH 1/2] mtd: rawnand: gpmi: Remove explicit default gpmi clock setting for i.MX6 Christian Eggers
2021-10-09 6:26 ` GPMI iMX6ull timeout on DMA Christian Eggers
2021-10-13 6:15 ` Christian Eggers
2021-10-08 13:13 ` Christian Eggers
2021-10-08 13:30 ` Miquel Raynal
2021-10-09 6:33 ` Christian Eggers
-- strict thread matches above, loose matches on Subject: below --
2018-10-02 13:22 GPMI IMX6ull timeout on dma Michael Nazzareno Trimarchi
2018-10-04 14:36 ` Michael Nazzareno Trimarchi
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190731082823.6284f5a9@collabora.com \
--to=boris.brezillon@collabora.com \
--cc=bbrezillon@kernel.org \
--cc=gerg@kernel.org \
--cc=linux-mtd@lists.infradead.org \
--cc=michael@amarulasolutions.com \
--cc=miquel.raynal@bootlin.com \
--cc=s.hauer@pengutronix.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).