Re: [PATCH v1 3/4] mtd: spinand: Add support continuous read operation

[Miquel Raynal <miquel.raynal@bootlin.com>]

Hi JaimeLiao,

jaimeliao.tw@gmail.com wrote on Thu, 11 Aug 2022 17:45:35 +0800:

> The continuous read operation includes three phases:
> Firstly, starting with the page read command and the 1st
> page data will be read into the cache after the read latency tRD.
> Secondly, Issuing the Read From Cache commands
> (03h/0Bh/3Bh/6Bh/BBh/EBh) to read out the data from cache continuously.
> After all the data is read out, the host should pull CS# high
> to terminate this continuous read operation and wait tRST for the NAND
> device resets read operation.
> 
> Continuous reads have a positive impact when reading more than
> one page and the column address is don't care in this operation,
> a full page data will be read out for each page.
> 
> The performance of continuous read mode is as follows. Set the
> flash to QUAD mode and run 25MZ direct mapping mode on the SPI

			       MHz

> bus and use the MTD test module to show the performance of
> continuous reads.

Please show before and after changes and just give us the lines
regarding the read speeds rather than all the output of the tool.

> 
> =================================================
> mtd_speedtest: MTD device: 0    count: 100
> mtd_speedtest: MTD device size 268435456, eraseblock size 131072,
>                page size 2048, count of eraseblocks 2048, pages per
>                eraseblock 64, OOB size 64
> mtd_test: scanning for bad eraseblocks
> mtd_test: scanned 100 eraseblocks, 0 are bad
> mtd_speedtest: testing eraseblock write speed
> mtd_speedtest: eraseblock write speed is 1298 KiB/s
> mtd_speedtest: testing eraseblock read speed
> mtd_speedtest: eraseblock read speed is 11053 KiB/s
> mtd_speedtest: testing page write speed
> mtd_speedtest: page write speed is 1291 KiB/s
> mtd_speedtest: testing page read speed
> mtd_speedtest: page read speed is 3240 KiB/s
> mtd_speedtest: testing 2 page write speed
> mtd_speedtest: 2 page write speed is 1289 KiB/s
> mtd_speedtest: testing 2 page read speed
> mtd_speedtest: 2 page read speed is 2909 KiB/s
> mtd_speedtest: Testing erase speed
> mtd_speedtest: erase speed is 45229 KiB/s
> mtd_speedtest: Testing 2x multi-block erase speed
> mtd_speedtest: 2x multi-block erase speed is 62135 KiB/s
> mtd_speedtest: Testing 4x multi-block erase speed
> mtd_speedtest: 4x multi-block erase speed is 60093 KiB/s
> mtd_speedtest: Testing 8x multi-block erase speed
> mtd_speedtest: 8x multi-block erase speed is 61244 KiB/s
> mtd_speedtest: Testing 16x multi-block erase speed
> mtd_speedtest: 16x multi-block erase speed is 61538 KiB/s
> mtd_speedtest: Testing 32x multi-block erase speed
> mtd_speedtest: 32x multi-block erase speed is 61835 KiB/s
> mtd_speedtest: Testing 64x multi-block erase speed
> mtd_speedtest: 64x multi-block erase speed is 60663 KiB/s
> mtd_speedtest: finished
> =================================================
> 
> Signed-off-by: JaimeLiao <jaimeliao.tw@gmail.com>
> ---
>  drivers/mtd/nand/spi/core.c | 99 +++++++++++++++++++++++++++++++++++++
>  include/linux/mtd/spinand.h |  1 +
>  2 files changed, 100 insertions(+)
> 
> diff --git a/drivers/mtd/nand/spi/core.c b/drivers/mtd/nand/spi/core.c
> index 380411feab6c..ef09bedda8d4 100644
> --- a/drivers/mtd/nand/spi/core.c
> +++ b/drivers/mtd/nand/spi/core.c
> @@ -386,6 +386,10 @@ static int spinand_read_from_cache_op(struct spinand_device *spinand,
>  	if (req->datalen) {
>  		buf = spinand->databuf;
>  		nbytes = nanddev_page_size(nand);
> +		if (spinand->use_continuous_read) {
> +			buf = req->databuf.in;
> +			nbytes = req->datalen;
> +		}

Does not look right. A cache read is still one page, and I believe the
caller should have taken care of that?

>  		column = 0;
>  	}
>  
> @@ -412,6 +416,9 @@ static int spinand_read_from_cache_op(struct spinand_device *spinand,
>  		buf += ret;
>  	}
>  
> +	if (spinand->use_continuous_read)
> +		return 0;

For me this is not the right place.

> +
>  	if (req->datalen)
>  		memcpy(req->databuf.in, spinand->databuf + req->dataoffs,
>  		       req->datalen);
> @@ -640,6 +647,80 @@ static int spinand_write_page(struct spinand_device *spinand,
>  	return nand_ecc_finish_io_req(nand, (struct nand_page_io_req *)req);
>  }
>  
> +static int spinand_mtd_continuous_read(struct mtd_info *mtd, loff_t from,
> +				       struct mtd_oob_ops *ops,
> +				       struct nand_io_iter *iter)
> +{
> +	struct spinand_device *spinand = mtd_to_spinand(mtd);
> +	struct nand_device *nand = mtd_to_nanddev(mtd);
> +	int ret = 0;
> +
> +	/*
> +	 * Continuous read mode could reduce some operation in On-die ECC free
> +	 * flash when read page sequentially.
> +	 */
> +	iter->req.type = NAND_PAGE_READ;
> +	iter->req.mode = MTD_OPS_RAW;

I don't get what you do here.

Continuous read shall either work with ECC engines or just not be
implemented at all. You cannot blindly disable ECC support.

> +	iter->req.dataoffs = nanddev_offs_to_pos(nand, from, &iter->req.pos);
> +	iter->req.databuf.in = ops->datbuf;
> +	iter->req.datalen = ops->len;
> +
> +	if (from & (nanddev_page_size(nand) - 1)) {
> +		pr_debug("%s: unaligned address\n", __func__);
> +		return -EINVAL;
> +	}
> +
> +	ret = spinand_continuous_read_enable(spinand);
> +	if (ret)
> +		return ret;
> +
> +	spinand->use_continuous_read = true;
> +
> +	ret = spinand_select_target(spinand, iter->req.pos.target);
> +	if (ret)
> +		return ret;
> +
> +	/*
> +	 * The continuous read operation including: firstly, starting with the
> +	 * page read command and the 1 st page data will be read into the cache
> +	 * after the read latency tRD. Secondly, Issuing the Read From Cache
> +	 * commands (03h/0Bh/3Bh/6Bh/BBh/EBh) to read out the data from cache
> +	 * continuously.
> +	 *
> +	 * The cache is divided into two halves, while one half of the cache is
> +	 * outputting the data, the other half will be loaded for the new data;
> +	 * therefore, the host can read out the data continuously from page to
> +	 * page. Multiple of Read From Cache commands can be issued in one
> +	 * continuous read operation, each Read From Cache command is required
> +	 * to read multiple 4-byte data exactly; otherwise, the data output will
> +	 * be out of sequence from one Read From Cache command to another Read
> +	 * From Cache command.
> +	 *
> +	 * After all the data is read out, the host should pull CS# high to
> +	 * terminate this continuous read operation and wait a 6us of tRST for
> +	 * the NAND device resets read operation. The data output for each page
> +	 * will always start from byte 0 and a full page data should be read out
> +	 * for each page.
> +	 */
> +	ret = spinand_read_page(spinand, &iter->req);
> +	if (ret)
> +		return ret;
> +
> +	ret = spinand_reset_op(spinand);
> +	if (ret)
> +		return ret;
> +
> +	ret = spinand_continuous_read_disable(spinand);
> +	if (ret)
> +		return ret;
> +
> +	spinand->use_continuous_read = false;

Any error in this function should lead to resetting use_continuous_read
to false and disabling continuous read on the flash side.

> +
> +	ops->retlen = iter->req.datalen;
> +
> +	return ret;
> +}
> +
>  static int spinand_mtd_read(struct mtd_info *mtd, loff_t from,
>  			    struct mtd_oob_ops *ops)
>  {
> @@ -656,6 +737,24 @@ static int spinand_mtd_read(struct mtd_info *mtd, loff_t from,
>  
>  	mutex_lock(&spinand->lock);
>  
> +	/*
> +	 * If the device support continuous read mode and read length larger
> +	 * than one page size will enter the continuous read mode. This mode
> +	 * helps avoid issuing a page read command and read from cache command
> +	 * again, and improves read performance for continuous addresses.
> +	 */
> +	if ((spinand->flags & SPINAND_HAS_CONT_READ_BIT) &&
> +	    (ops->len > nanddev_page_size(nand))) {
> +		ret = spinand_mtd_continuous_read(mtd, from, ops, &iter);
> +
> +		mutex_unlock(&spinand->lock);
> +
> +		if (ecc_failed && !ret)
> +			ret = -EBADMSG;
> +
> +		return ret ? ret : max_bitflips;
> +	}
> +
>  	nanddev_io_for_each_page(nand, NAND_PAGE_READ, from, ops, &iter) {
>  		if (disable_ecc)
>  			iter.req.mode = MTD_OPS_RAW;
> diff --git a/include/linux/mtd/spinand.h b/include/linux/mtd/spinand.h
> index d70a6f49cc6f..c296d4d0dda5 100644
> --- a/include/linux/mtd/spinand.h
> +++ b/include/linux/mtd/spinand.h
> @@ -308,6 +308,7 @@ struct spinand_ecc_info {
>  
>  #define SPINAND_HAS_QE_BIT		BIT(0)
>  #define SPINAND_HAS_CR_FEAT_BIT		BIT(1)
> +#define SPINAND_HAS_CONT_READ_BIT	BIT(2)

Is this bit standard?

>  
>  /**
>   * struct spinand_ondie_ecc_conf - private SPI-NAND on-die ECC engine structure


Thanks,
Miquèl

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/