Hello Boris, Am Mittwoch, 26. Juli 2017, 20:33:26 schrieb Boris Brezillon: > Okay, first thing to test: revert f9ce2eddf176 ("mtd: nand: atmel: Add > ->setup_data_interface() hooks"). You may have to revert other > commits to compile the driver. > > If it works, I'd like you to drop SMC timings in both situations (with > and without this commit). > > I'd also like to to dump NAND timings (those passed to > ->setup_data_interface()). So based on those three atmel-ebi patches from earlier this week I used the attached patch to dump the nand timings and smc settings before the get applied. clk mck runs at 132096000 Hz (slow_xtal 32768, main_xtal 18432000). Previously clock settings for NAND were set in (very old) U- Boot to this (double checked, Linux didn't touch it): U-Boot> md.l 0xffffef1c 1 ffffef1c: 0001000a .... U-Boot> md.l 0xffffec30 4 ffffec30: 00010001 03030303 00050005 00020003 ................ So setup, pulse, cycle, tdf all to quite low number of clock cycles, but as far as I can tell this worked with all flash chips we had connected over the years. Now with the old Hynix flash chip, I get the following: atmel-nand-controller 10000000.ebi:nand-controller: atmel_smc_nand_setup_data_interface(csline: 0, type: 0) atmel-nand-controller 10000000.ebi:nand-controller: tBERS_max: 0, tCCS_min: 500000, tPROG_max: 0, tR_max: 200000000 atmel-nand-controller 10000000.ebi:nand-controller: tALH_min: 20000, tADL_min: 400000, tALS_min: 50000, tAR_min: 25000 atmel-nand-controller 10000000.ebi:nand-controller: tCEA_max: 100000, tCEH_min: 20000, tCH_min: 20000, tCHZ_max: 100000 atmel-nand-controller 10000000.ebi:nand-controller: tCLH_min: 20000, tCLR_min: 20000, tCLS_min: 50000, tCOH_min: 0 atmel-nand-controller 10000000.ebi:nand-controller: tCS_min: 70000, tDH_min: 20000, tDS_min: 40000, tFEAT_max: 1000000 atmel-nand-controller 10000000.ebi:nand-controller: tIR_min: 10000, tITC_max: 1000000, tRC_min: 100000, tREA_max: 40000 atmel-nand-controller 10000000.ebi:nand-controller: tREH_min: 30000, tRHOH_min: 0, tRHW_min: 200000, tRHZ_max: 200000 atmel-nand-controller 10000000.ebi:nand-controller: tRLOH_min: 0, tRP_min: 50000, tRR_min: 40000, tRST_max: 250000000000 atmel-nand-controller 10000000.ebi:nand-controller: tWB_max: 200000, tWC_min: 100000, tWH_min: 30000, tWHR_min: 120000 atmel-nand-controller 10000000.ebi:nand-controller: tWP_min: 50000, tWW_min: 100000 atmel-nand-controller 10000000.ebi:nand-controller: smcconf: setup: 0x00000002, pulse: 0x0f080f08, cycle: 0x000f000f, timings: 0x88060483, mode: 0x001f0003 nand: Could not find valid ONFI parameter page; aborting nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda nand: Hynix NAND 256MiB 3,3V 8-bit nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 $ devmem 0xffffef1c 0x0001000A $ devmem 0xffffec30 0x00000002 $ devmem 0xffffec34 0x0F080F08 $ devmem 0xffffec38 0x000F000F $ devmem 0xffffec3c 0x001F0003 To me those values look like some kind of defaults every nand chip should run with? The failing Spansion chip here: atmel-nand-controller 10000000.ebi:nand-controller: atmel_smc_nand_setup_data_interface(csline: 0, type: 0) atmel-nand-controller 10000000.ebi:nand-controller: tBERS_max: 0, tCCS_min: 500000, tPROG_max: 0, tR_max: 200000000 atmel-nand-controller 10000000.ebi:nand-controller: tALH_min: 20000, tADL_min: 400000, tALS_min: 50000, tAR_min: 25000 atmel-nand-controller 10000000.ebi:nand-controller: tCEA_max: 100000, tCEH_min: 20000, tCH_min: 20000, tCHZ_max: 100000 atmel-nand-controller 10000000.ebi:nand-controller: tCLH_min: 20000, tCLR_min: 20000, tCLS_min: 50000, tCOH_min: 0 atmel-nand-controller 10000000.ebi:nand-controller: tCS_min: 70000, tDH_min: 20000, tDS_min: 40000, tFEAT_max: 1000000 atmel-nand-controller 10000000.ebi:nand-controller: tIR_min: 10000, tITC_max: 1000000, tRC_min: 100000, tREA_max: 40000 atmel-nand-controller 10000000.ebi:nand-controller: tREH_min: 30000, tRHOH_min: 0, tRHW_min: 200000, tRHZ_max: 200000 atmel-nand-controller 10000000.ebi:nand-controller: tRLOH_min: 0, tRP_min: 50000, tRR_min: 40000, tRST_max: 250000000000 atmel-nand-controller 10000000.ebi:nand-controller: tWB_max: 200000, tWC_min: 100000, tWH_min: 30000, tWHR_min: 120000 atmel-nand-controller 10000000.ebi:nand-controller: tWP_min: 50000, tWW_min: 100000 atmel-nand-controller 10000000.ebi:nand-controller: smcconf: setup: 0x00000002, pulse: 0x0f080f08, cycle: 0x000f000f, timings: 0x88060483, mode: 0x001f0003 nand: device found, Manufacturer ID: 0x01, Chip ID: 0xda nand: AMD/Spansion S34ML02G1 nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 atmel-nand-controller 10000000.ebi:nand-controller: atmel_smc_nand_setup_data_interface(csline: -1, type: 0) atmel-nand-controller 10000000.ebi:nand-controller: tBERS_max: 1410065408, tCCS_min: 100000, tPROG_max: 700000000, tR_max: 25000000 atmel-nand-controller 10000000.ebi:nand-controller: tALH_min: 5000, tADL_min: 400000, tALS_min: 10000, tAR_min: 10000 atmel-nand-controller 10000000.ebi:nand-controller: tCEA_max: 25000, tCEH_min: 20000, tCH_min: 5000, tCHZ_max: 30000 atmel-nand-controller 10000000.ebi:nand-controller: tCLH_min: 5000, tCLR_min: 10000, tCLS_min: 10000, tCOH_min: 15000 atmel-nand-controller 10000000.ebi:nand-controller: tCS_min: 20000, tDH_min: 5000, tDS_min: 10000, tFEAT_max: 1000000 atmel-nand-controller 10000000.ebi:nand-controller: tIR_min: 0, tITC_max: 1000000, tRC_min: 25000, tREA_max: 20000 atmel-nand-controller 10000000.ebi:nand-controller: tREH_min: 10000, tRHOH_min: 15000, tRHW_min: 100000, tRHZ_max: 100000 atmel-nand-controller 10000000.ebi:nand-controller: tRLOH_min: 5000, tRP_min: 12000, tRR_min: 20000, tRST_max: 500000000 atmel-nand-controller 10000000.ebi:nand-controller: tWB_max: 100000, tWC_min: 25000, tWH_min: 10000, tWHR_min: 80000 atmel-nand-controller 10000000.ebi:nand-controller: tWP_min: 12000, tWW_min: 100000 atmel-nand-controller 10000000.ebi:nand-controller: smcconf: setup: 0x00000001, pulse: 0x05020502, cycle: 0x00050005, timings: 0x88030282, mode: 0x001b0003 atmel-nand-controller 10000000.ebi:nand-controller: atmel_smc_nand_setup_data_interface(csline: 0, type: 0) atmel-nand-controller 10000000.ebi:nand-controller: tBERS_max: 1410065408, tCCS_min: 100000, tPROG_max: 700000000, tR_max: 25000000 atmel-nand-controller 10000000.ebi:nand-controller: tALH_min: 5000, tADL_min: 400000, tALS_min: 10000, tAR_min: 10000 atmel-nand-controller 10000000.ebi:nand-controller: tCEA_max: 25000, tCEH_min: 20000, tCH_min: 5000, tCHZ_max: 30000 atmel-nand-controller 10000000.ebi:nand-controller: tCLH_min: 5000, tCLR_min: 10000, tCLS_min: 10000, tCOH_min: 15000 atmel-nand-controller 10000000.ebi:nand-controller: tCS_min: 20000, tDH_min: 5000, tDS_min: 10000, tFEAT_max: 1000000 atmel-nand-controller 10000000.ebi:nand-controller: tIR_min: 0, tITC_max: 1000000, tRC_min: 25000, tREA_max: 20000 atmel-nand-controller 10000000.ebi:nand-controller: tREH_min: 10000, tRHOH_min: 15000, tRHW_min: 100000, tRHZ_max: 100000 atmel-nand-controller 10000000.ebi:nand-controller: tRLOH_min: 5000, tRP_min: 12000, tRR_min: 20000, tRST_max: 500000000 atmel-nand-controller 10000000.ebi:nand-controller: tWB_max: 100000, tWC_min: 25000, tWH_min: 10000, tWHR_min: 80000 atmel-nand-controller 10000000.ebi:nand-controller: tWP_min: 12000, tWW_min: 100000 atmel-nand-controller 10000000.ebi:nand-controller: smcconf: setup: 0x00000001, pulse: 0x05020502, cycle: 0x00050005, timings: 0x88030282, mode: 0x001b0003 I could not double check here with devmem, because I got no login prompt anymore, all those errors from the first mail follow. I didn't double check with the S34ML02G1 datasheet here, but those smc timings he wants to set don't look completely bad. Greets Alex