Re: kernel messages from INFTL

Andre
2005-06-30T17:49:17Z

Hi Greg,

Greg Ungerer wrote:
> Hi Andre,
>
> Andre wrote:
>> First of all, thank you Thomas for your help on trying to get my
>> diskonchip2000 to be recognized by linuxmtd.
>>
>> After enabling the right config flags in the kernel, I can now mount
>> my diskonchip2000.
>>
>> There were some messages during the initial loading of the inftl
>> module that frightened me a bit. Here is the entire output from
>> dmesg: ==================
>> DiskOnChip found at 0xd0000
>> Detected 3 chips per floor.
>> NAND device: Manufacturer ID: 0xec, Chip ID: 0x79 (Samsung NAND
>> 128MiB 3,3V 8-bit)
>> 3 NAND chips detected
>> Bad block table not found for chip 0
>> Bad block table not found for chip 0
>> Found DiskOnChip BNAND Media Header at 0x4000
>> bootRecordID = BNAND
>> NoOfBootImageBlocks = 0
>> NoOfBinaryPartitions = 1
>> NoOfBDTLPartitions = 1
>> BlockMultiplerBits = 0
>> FormatFlgs = 1
>> OsakVersion = 5.1.4.0
>> PercentUsed = 98
>> PARTITION[0] ->
>> virtualUnits = 4
>> firstUnit = 2
>> lastUnit = 5
>> flags = 0x20000000
>> spareUnits = 0
>> PARTITION[1] ->
>> virtualUnits = 24072
>> firstUnit = 11
>> lastUnit = 24575
>> flags = 0xc0000000
>> spareUnits = 2
>> Creating 2 MTD partitions on "DiskOnChip 2000 (INFTL Model)":
>> 0x00008000-0x00018000 : " DiskOnChip BDK partition"
>> 0x0002c000-0x18000000 : " DiskOnChip BDTL partition"
>>
>> <Andre> looks ok up until here
>>
>> INFTL: inftlcore.c $Revision: 1.18 $, inftlmount.c $Revision: 1.16 $
>> INFTL: corrupt block 10588 in chain 10588, chain length 0, erase
>> mark 0x0? INFTL: formatting chain at block 10588
>> INFTL: formatting block 10588
>> INFTL: error while formatting block 10588
>> INFTL: corrupt block 15274 in chain 15274, chain length 0, erase
>> mark 0x0? INFTL: formatting chain at block 15274
>> INFTL: formatting block 15274
>> INFTL: error while formatting block 15274
>> INFTL: corrupt block 21286 in chain 21286, chain length 0, erase
>> mark 0x0? INFTL: formatting chain at block 21286
>> INFTL: formatting block 21286
>> INFTL: error while formatting block 21286
>> INFTL: corrupt block 24574 in chain 24574, chain length 0, erase mark
>> 0xffff?
>> INFTL: formatting chain at block 24574
>> INFTL: formatting block 24574
>> INFTL: corrupt block 24575 in chain 24575, chain length 0, erase mark
>> 0xffff?
>> INFTL: formatting chain at block 24575
>> INFTL: formatting block 24575
>> inftla: inftla1
>> ==================
>> The INFTL messages do not appear on subsequent loads of the inftl
>> module. Can somebody please explain what happened, i.e. should I be
>> concerned?
>
> The INFTL code is telling you that it didn't think the chains
> where logically correct. So it went ahead and tried to fix them up.
> Once fixed you should not see any messages on the next boot (as
> you didn't). Certainly not normal (or good).

The device really started to act up on subsequent boot and I couldn't even
format it anymore with m-sys tools. The dformat utility complained about not
being able to find the bad block table.

> I take it you are running this on a device that was formatted
> using the M-systems tools?

correct

> What kernel version are you using here?

stock 2.6.11 with mtd 20050612 snapshot.

Thanks for your reply,
Andre