Problem with NAND on MIPS32 board (mtd 20050122)

[Dawid Prus - praca <dawid.prus@o2.pl>]

Hello.

I'm trying to use a MIPS32-24KE (from Vitesse 7429) with NAND flash SAMSUNG K9F1G08U0B / Micron 29F2G08AAD,
and I have problem with reading it. Software I'm using is KAMIKAZE 8.09.2 (mtd 20050122)

Problem is when i try to read also the ID or any data from chip.
When I read ID for SAMSUNG I getting:
NAND device: Manufacturer ID: 0xFF, Chip ID: 0xEC (next readed byte is 0xF1) - 0xFF in mfc field makes
that my NAND is not recognized
Same situation with Micron (first byte 0xFF)

I changed nand_base.c and put one extra read command before reading first ID byte:

chip->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1);
read_byte(mtd);  // added command
*maf_id = chip->read_byte(mtd);

NAND is now recognized and I have log (dmesg) like this:
.....
RedBoot partition parsing not available
Using physmap partition information                                             
Creating 4 MTD partitions on "physmap-flash.0":                                 
0x00000000-0x00040000 : "redboot"                                               
0x00040000-0x00080000 : "config"                                                
0x007c0000-0x008c0000 : "linux"                                                 
0x008c0000-0x00bc0000 : "rootfs"                                                
mtd: partition "rootfs" set to be root filesystem                               
block2mtd: version $Revision: 1.30 $                                            
NAND device: ec,f1,80,15,40 // this is my exta function                                      
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-b)
Scanning device for bad blocks                                                  
Creating 1 MTD partitions on "gen_nand":                                        
0x00000000-0x08000000 : "rootfs_data"                                           
TCP cubic registered                                                            
NET: Registered protocol family 17                                              
VFS: Mounted root (squashfs filesystem) readonly.                               
Freeing unused kernel memory: 108k freed
......


After this, when NAND is recognized I have still problem with reading
(first byte is FF and other are shifted to right)
You can see it when I do nandtest (from mtd-utils)

root@OpenWrt:/# nandtest /dev/mtd4                                              
ECC corrections: 0                                                              
ECC failures   : 0                                                              
Bad blocks     : 0                                                              
BBT blocks     : 0                                                              
00000000: reading...
ECC failed at 00000000                                                          
00000000: checking...                                                           
compare failed. seed 1797617246                                                 
Byte 0x0 is ff should be 0a                                                     
Byte 0x1 is 0a should be 6e                                                     
Byte 0x2 is 6e should be 7e                                                     
Byte 0x3 is 7e should be 8e                                                     
Byte 0x4 is 8e should be aa                                                     
Byte 0x5 is aa should be 23                                                     
Byte 0x6 is 23 should be 91 

From myself I can add that NAND i permanently selected - CS pin goes to GND (through 10k)

Please help me to find some solution to fix this issue.
Sorry about my english

Best Regards
Dawid