From: Kostas Nakos <knakos@inaccessnetworks.com>
Cc: linux-mtd@lists.infradead.org
Subject: Re: [PATCH] ndfc driver
Date: Wed, 07 Jan 2009 11:51:18 +0200 [thread overview]
Message-ID: <49647B16.50006@inaccessnetworks.com> (raw)
In-Reply-To: <20090105202340.7fd0f8c1@lappy.seanm.ca>
[-- Attachment #1: Type: text/plain, Size: 388 bytes --]
Sean MacLennan wrote:
> That is where the NAND is on the warp. Could you post the complete dts?
Of course; attached. This is the one I use to boot the 2.6.28 kernel
(with the hackish ndfc patches). The only changes required while
migrating the entire dts from 2.6.26 to .28 concern just the ndfc block
and particularly the parameter names according to the new scheme.
Thanks,
Kostas
[-- Attachment #2: device.dts --]
[-- Type: text/plain, Size: 15928 bytes --]
/ {
#address-cells = <2>;
#size-cells = <1>;
model = "amcc";
compatible = "amcc";
dcr-parent = <&/cpus/cpu@0>;
aliases {
ethernet0 = &EMAC0;
ethernet1 = &EMAC1;
serial0 = &UART0;
serial1 = &UART1;
};
cpus {
#address-cells = <1>;
#size-cells = <0>;
cpu@0 {
device_type = "cpu";
model = "PowerPC,440EPx";
reg = <0>;
clock-frequency = <0>; /* Filled in by zImage */
timebase-frequency = <0>; /* Filled in by zImage */
i-cache-line-size = <20>;
d-cache-line-size = <20>;
i-cache-size = <8000>;
d-cache-size = <8000>;
dcr-controller;
dcr-access-method = "native";
};
};
memory {
device_type = "memory";
reg = <0 0 0>; /* Filled in by zImage */
};
UIC0: interrupt-controller0 {
compatible = "ibm,uic-440epx","ibm,uic";
interrupt-controller;
cell-index = <0>;
dcr-reg = <0c0 009>;
#address-cells = <0>;
#size-cells = <0>;
#interrupt-cells = <2>;
};
UIC1: interrupt-controller1 {
compatible = "ibm,uic-440epx","ibm,uic";
interrupt-controller;
cell-index = <1>;
dcr-reg = <0d0 009>;
#address-cells = <0>;
#size-cells = <0>;
#interrupt-cells = <2>;
interrupts = <1e 4 1f 4>; /* cascade */
interrupt-parent = <&UIC0>;
};
UIC2: interrupt-controller2 {
compatible = "ibm,uic-440epx","ibm,uic";
interrupt-controller;
cell-index = <2>;
dcr-reg = <0e0 009>;
#address-cells = <0>;
#size-cells = <0>;
#interrupt-cells = <2>;
interrupts = <1c 4 1d 4>; /* cascade */
interrupt-parent = <&UIC0>;
};
SDR0: sdr {
compatible = "ibm,sdr-440epx", "ibm,sdr-440ep";
dcr-reg = <00e 002>;
};
CPR0: cpr {
compatible = "ibm,cpr-440epx", "ibm,cpr-440ep";
dcr-reg = <00c 002>;
};
plb {
compatible = "ibm,plb-440epx", "ibm,plb4";
#address-cells = <2>;
#size-cells = <1>;
ranges;
clock-frequency = <0>; /* Filled in by zImage */
SDRAM0: sdram {
compatible = "ibm,sdram-440epx", "ibm,sdram-44x-ddr2denali";
dcr-reg = <010 2>;
};
DMA0: dma {
compatible = "ibm,dma-440epx", "ibm,dma-4xx";
dcr-reg = <100 027>;
};
MAL0: mcmal {
compatible = "ibm,mcmal-440epx", "ibm,mcmal2";
dcr-reg = <180 62>;
num-tx-chans = <2>;
num-rx-chans = <2>;
interrupt-parent = <&MAL0>;
interrupts = <0 1 2 3 4>;
#interrupt-cells = <1>;
#address-cells = <0>;
#size-cells = <0>;
interrupt-map = </*TXEOB*/ 0 &UIC0 a 4
/*RXEOB*/ 1 &UIC0 b 4
/*SERR*/ 2 &UIC1 0 4
/*TXDE*/ 3 &UIC1 1 4
/*RXDE*/ 4 &UIC1 2 4>;
interrupt-map-mask = <ffffffff>;
};
ndfc@0,d0000000 {
device_type = "nand";
compatible = "ibm,ndfc";
reg = <1 d0000000 2000>;
bank-settings = <80002222>;
ccr = <00001000>;
#address-cells = <1>;
#size-cells = <1>;
nand {
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0 60000>;
};
partition@1 {
label = "uboot-env-1";
reg = <60000 4000>;
};
partition@2 {
label = "uboot-env-2";
reg = <64000 4000>;
};
partition@3 {
label = "device-tree";
reg = <68000 4000>;
};
partition@4 {
label = "bootfs";
reg = <6c000 340000>;
};
partition@5 {
label = "rootfs";
reg = <3ac000 0>;
};
};
};
USB0: ehci@e0000300 {
compatible = "ibm,usb-ehci-440epx", "usb-ehci";
interrupt-parent = <&UIC0>;
interrupts = <1a 4>;
reg = <0 e0000300 90 0 e0000390 70>;
big-endian;
};
POB0: opb {
compatible = "ibm,opb-440epx", "ibm,opb";
#address-cells = <1>;
#size-cells = <1>;
ranges = <00000000 1 00000000 80000000
80000000 1 80000000 80000000>;
interrupt-parent = <&UIC1>;
interrupts = <7 4>;
clock-frequency = <0>; /* Filled in by zImage */
EBC0: ebc {
compatible = "ibm,ebc-440epx", "ibm,ebc";
dcr-reg = <012 2>;
#address-cells = <2>;
#size-cells = <1>;
clock-frequency = <0>; /* Filled in by zImage */
interrupts = <5 1>;
interrupt-parent = <&UIC1>;
};
UART0: serial@ef600300 {
device_type = "serial";
compatible = "ns16550";
reg = <ef600300 8>;
virtual-reg = <ef600300>;
clock-frequency = <0>; /* Filled in by zImage */
current-speed = <1c200>;
interrupt-parent = <&UIC0>;
interrupts = <0 4>;
};
UART1: serial@ef600400 {
device_type = "serial";
compatible = "ns16550";
reg = <ef600400 8>;
virtual-reg = <ef600400>;
clock-frequency = <0>;
current-speed = <0>;
interrupt-parent = <&UIC0>;
interrupts = <1 4>;
};
IIC0: i2c@ef600700 {
compatible = "ibm,iic-440gpx", "ibm,iic";
reg = <ef600700 14>;
index = <0>;
interrupt-parent = <&UIC0>;
interrupts = <2 4>;
};
IIC1: i2c@ef600800 {
compatible = "ibm,iic-440gpx", "ibm,iic";
reg = <ef600800 14>;
index = <1>;
interrupt-parent = <&UIC0>;
interrupts = <7 4>;
};
GPIO0: gpio@ef600b00 {
compatible = "ibm,gpio-440ep";
reg = <ef600b00 48>;
#gpio-cells = <2>;
gpio-controller;
};
GPIO1: gpio@ef600c00 {
compatible = "ibm,gpio-440ep";
reg = <ef600c00 48>;
#gpio-cells = <2>;
gpio-controller;
};
ZMII0: emac-zmii@ef600d00 {
compatible = "ibm,zmii-440epx", "ibm,zmii";
reg = <ef600d00 c>;
};
RGMII0: emac-rgmii@ef601000 {
compatible = "ibm,rgmii-440epx", "ibm,rgmii";
reg = <ef601000 8>;
has-mdio;
};
EMAC0: ethernet@ef600e00 {
device_type = "network";
compatible = "ibm,emac-440epx", "ibm,emac4";
interrupt-parent = <&EMAC0>;
interrupts = <0 1>;
#interrupt-cells = <1>;
#address-cells = <0>;
#size-cells = <0>;
interrupt-map = </*Status*/ 0 &UIC0 18 4
/*Wake*/ 1 &UIC1 1d 4>;
reg = <ef600e00 70>;
local-mac-address = [000000000000];
mal-device = <&MAL0>;
mal-tx-channel = <0>;
mal-rx-channel = <0>;
cell-index = <0>;
max-frame-size = <2328>;
rx-fifo-size = <1000>;
tx-fifo-size = <800>;
phy-mode = "rgmii";
phy-map = <00000000>;
zmii-device = <&ZMII0>;
zmii-channel = <0>;
rgmii-device = <&RGMII0>;
rgmii-channel = <0>;
has-inverted-stacr-oc;
has-new-stacr-staopc;
};
EMAC1: ethernet@ef600f00 {
device_type = "network";
compatible = "ibm,emac-440epx", "ibm,emac4";
interrupt-parent = <&EMAC1>;
interrupts = <0 1>;
#interrupt-cells = <1>;
#address-cells = <0>;
#size-cells = <0>;
interrupt-map = </*Status*/ 0 &UIC0 19 4
/*Wake*/ 1 &UIC1 1f 4>;
reg = <ef600f00 70>;
local-mac-address = [000000000000];
mal-device = <&MAL0>;
mal-tx-channel = <1>;
mal-rx-channel = <1>;
cell-index = <1>;
max-frame-size = <2328>;
rx-fifo-size = <1000>;
tx-fifo-size = <800>;
phy-mode = "rgmii";
phy-map = <00000000>;
zmii-device = <&ZMII0>;
zmii-channel = <1>;
rgmii-device = <&RGMII0>;
rgmii-channel = <1>;
has-inverted-stacr-oc;
has-new-stacr-staopc;
};
LEDS0: led0 {
compatible = "gpio-led";
label="led0";
gpios = <&GPIO1 1 0>;
};
LEDS1: led1 {
compatible = "gpio-led";
label="led1";
gpios = <&GPIO1 0 0>;
};
LEDS2: led2 {
compatible = "gpio-led";
label="led2";
gpios = <&GPIO0 1f 0>;
};
LEDS3: led3 {
compatible = "gpio-led";
label="led3";
gpios = <&GPIO0 1e 0>;
};
LEDS4: led4 {
compatible = "gpio-led";
label="led4";
gpios = <&GPIO0 1d 0>;
};
BUTTON0: button {
gpios = <&GPIO1 c 0
>;
compatible = "gpio-button";
interrupt-parent = <&UIC0>;
interrupts = <1b 2>;
};
};
PCI0: pci@1ec000000 {
device_type = "pci";
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
compatible = "ibm,plb440epx-pci", "ibm,plb-pci";
primary;
reg = <1 eec00000 8 /* Config space access */
1 eed00000 4 /* IACK */
1 eed00000 4 /* Special cycle */
1 ef400000 40>; /* Internal registers */
ranges = <02000000 0 80000000 1 80000000 0 40000000
01000000 0 00000000 1 e8000000 0 00010000
01000000 0 00000000 1 e8800000 0 03800000>;
dma-ranges = <42000000 0 0 0 0 0 80000000>;
interrupt-map-mask = <2800 0 0 0>;
interrupt-map = <
2000 0 0 0 &UIC2 3 8
2800 0 0 0 &UIC2 4 8
>;
};
};
chosen {
linux,stdout-path = "/plb/opb/serial@ef600300";
bootargs = "console=ttyS0,115200 root=1f05 rootfstype=jffs2 getty_cons=ttyS0";
};
};
next prev parent reply other threads:[~2009-01-07 10:09 UTC|newest]
Thread overview: 28+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-12-23 12:26 [PATCH] ndfc driver Kostas Nakos
2008-12-23 22:00 ` Sean MacLennan
2008-12-24 6:58 ` knakos
2008-12-27 1:56 ` Sean MacLennan
2008-12-29 10:58 ` Kostas Nakos
2009-01-06 1:23 ` Sean MacLennan
2009-01-07 9:51 ` Kostas Nakos [this message]
2009-01-07 17:21 ` Sean MacLennan
2009-01-08 15:37 ` Kostas Nakos
-- strict thread matches above, loose matches on Subject: below --
2008-12-04 3:28 Sean MacLennan
2008-12-04 14:01 ` Josh Boyer
2008-12-04 17:17 ` Sean MacLennan
2008-12-09 0:34 ` Sean MacLennan
2008-12-09 2:11 ` Anton Vorontsov
2008-12-09 2:45 ` Sean MacLennan
2008-12-09 3:32 ` Josh Boyer
2008-12-09 4:54 ` Sean MacLennan
2008-12-09 7:57 ` Mitch Bradley
2008-12-10 4:01 ` Sean MacLennan
2008-12-10 8:28 ` Mitch Bradley
2008-12-09 6:10 ` Stefan Roese
2008-12-09 11:24 ` Josh Boyer
2008-12-10 23:16 ` Sean MacLennan
2008-12-17 4:14 ` Sean MacLennan
2008-12-17 11:34 ` Josh Boyer
2008-12-17 13:26 ` Josh Boyer
2008-12-09 0:51 ` Sean MacLennan
2008-10-30 6:08 Sean MacLennan
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=49647B16.50006@inaccessnetworks.com \
--to=knakos@inaccessnetworks.com \
--cc=linux-mtd@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox