From: "Kári Davíðsson" <kari.davidsson@marel.com>
To: "dedekind1@gmail.com" <dedekind1@gmail.com>
Cc: Piotr Ziecik <kosmo@semihalf.com>, Detlev Zundel <dzu@denx.de>,
"linuxppc-dev@ozlabs.org" <linuxppc-dev@ozlabs.org>,
"linux-mtd@lists.infradead.org" <linux-mtd@lists.infradead.org>,
Anatolij Gustschin <agust@denx.de>,
David Woodhouse <dwmw2@infradead.org>
Subject: Re: [PATCH v4 04/11] mtd: Add MPC5121 NAND Flash Controller driver
Date: Tue, 23 Feb 2010 15:54:04 +0000 [thread overview]
Message-ID: <4B83FA1C.8000902@marel.com> (raw)
In-Reply-To: <1266307868.11659.177.camel@localhost>
Any special reason this in MPC5121 Revision 2 only?
I did not see anything that contradicted the rev 3 manual in the code.
But there is one harmless bug (since the NFC_CMD_FAIL symbol is never used), i.e.
git diff
diff --git a/drivers/mtd/nand/mpc5121_nfc.c b/drivers/mtd/nand/mpc5121_nfc.c
index 191bf99..38a99ef 100644
--- a/drivers/mtd/nand/mpc5121_nfc.c
+++ b/drivers/mtd/nand/mpc5121_nfc.c
@@ -100,7 +100,7 @@
#define NFC_OUTPUT (1 << 3)
#define NFC_ID (1 << 4)
#define NFC_STATUS (1 << 5)
-#define NFC_CMD_FAIL (1 << 15)
+#define NFC_CMD_FAIL (1 << 14)
#define NFC_INT (1 << 15)
/* Bit Definitions: NFC_WRPROT */
The NAND chip is is detected (given that I disable the Revison check),
but the /dev7mtd0 is not accessable as block device. Is that normal?
The UBIFS also gives up I am assuming because the /dev/mtd0 is not block device.
rg
kd
On 02/16/2010 08:11 AM, Artem Bityutskiy wrote:
> On Mon, 2010-02-15 at 18:35 +0100, Anatolij Gustschin wrote:
>> Adds NAND Flash Controller driver for MPC5121 Revision 2.
>> All device features, except hardware ECC and power management,
>> are supported.
>>
>> Signed-off-by: Piotr Ziecik<kosmo@semihalf.com>
>> Signed-off-by: Wolfgang Denk<wd@denx.de>
>> Signed-off-by: Anatolij Gustschin<agust@denx.de>
>> Acked-by: Grant Likely<grant.likely@secretlab.ca>
>> Cc:<linux-mtd@lists.infradead.org>
>> Cc: Grant Likely<grant.likely@secretlab.ca>
>> Cc: John Rigby<jcrigby@gmail.com>
>> ---
>> Changes since v3:
>> - include 'asm/mpc5121.h' header instead of 'asm/mpc5xxx.h'.
>> This change is needed because arch patch adding reset
>> module definition was reworked and doesn't add mpc5121
>> specific definitions to common header for mpc52xx/mpc5121.
>>
>> Changes since v2:
>> - move the arch bits into separate patch
>> (it is the next patch in this series now)
>> - use __devinit/__devexit/__devexit_p and __devinitdata
>>
>> Changes since v1:
>> - add logfile with changes since previous version
>>
>> Changes since the patch version submitted in May 2009:
>>
>> - move mpc5121_nfc.h to the driver .c as there is only one user
>> - remove DRV_VERSION macro
>> - replace printk() by dev_*()
>> - drop unnecessary .suspend and .resume initializations
>> - remove duplicate .name/.owner settings
>> - fix mpc5121_nfc_init() to "return of_register_platform_driver(&mpc5121_nfc_driver);"
>> - move module_init() to just below the init function
>> - remove MODULE_VERSION
>> - use "mtd: Add MPC5121 NAND Flash Controller driver" as the subject,
>> previously it was "mpc5121: Added NAND Flash Controller driver.
>>
>> drivers/mtd/nand/Kconfig | 7 +
>> drivers/mtd/nand/Makefile | 1 +
>> drivers/mtd/nand/mpc5121_nfc.c | 916 ++++++++++++++++++++++++++++++++++++++++
>> 3 files changed, 924 insertions(+), 0 deletions(-)
>> create mode 100644 drivers/mtd/nand/mpc5121_nfc.c
>
> Pushed to my l2-mtd-2.6.git / dunno.
>
next prev parent reply other threads:[~2010-02-23 15:54 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-02-05 13:42 [PATCH v3 00/11] Update support for MPC512x Anatolij Gustschin
2010-02-05 13:42 ` [PATCH v3 04/11] mtd: Add MPC5121 NAND Flash Controller driver Anatolij Gustschin
2010-02-10 2:42 ` Grant Likely
2010-03-30 13:15 ` Artem Bityutskiy
2010-02-15 17:35 ` [PATCH v4 " Anatolij Gustschin
2010-02-16 8:11 ` Artem Bityutskiy
2010-02-23 15:54 ` Kári Davíðsson [this message]
2010-02-09 8:48 ` [PATCH v3 00/11] Update support for MPC512x Anatolij Gustschin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4B83FA1C.8000902@marel.com \
--to=kari.davidsson@marel.com \
--cc=agust@denx.de \
--cc=dedekind1@gmail.com \
--cc=dwmw2@infradead.org \
--cc=dzu@denx.de \
--cc=kosmo@semihalf.com \
--cc=linux-mtd@lists.infradead.org \
--cc=linuxppc-dev@ozlabs.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).