[PATCH 004/104] mtd: drop physmap_configure

Dmitry Eremin-Solenikov
2011-06-02T14:51:36Z

physmap_configure() and physmap_set_partitions() have no users in kernel.
Out of kernel users should have been converted to regular platform device
long ago. Drop support for this obsolete API.

Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
---
drivers/mtd/maps/Kconfig | 6 ------
drivers/mtd/maps/physmap.c | 15 ---------------
include/linux/mtd/physmap.h | 17 -----------------
3 files changed, 0 insertions(+), 38 deletions(-)

diff --git a/drivers/mtd/maps/Kconfig b/drivers/mtd/maps/Kconfig
index 11cc230..46eca3b 100644
--- a/drivers/mtd/maps/Kconfig
+++ b/drivers/mtd/maps/Kconfig
@@ -41,8 +41,6 @@ config MTD_PHYSMAP_START
are mapped on your particular target board. Refer to the
memory map which should hopefully be in the documentation for
your board.
- Ignore this option if you use run-time physmap configuration
- (i.e., run-time calling physmap_configure()).

config MTD_PHYSMAP_LEN
hex "Physical length of flash mapping"
@@ -55,8 +53,6 @@ config MTD_PHYSMAP_LEN
than the total amount of flash present. Refer to the memory
map which should hopefully be in the documentation for your
board.
- Ignore this option if you use run-time physmap configuration
- (i.e., run-time calling physmap_configure()).

config MTD_PHYSMAP_BANKWIDTH
int "Bank width in octets"
@@ -67,8 +63,6 @@ config MTD_PHYSMAP_BANKWIDTH
in octets. For example, if you have a data bus width of 32
bits, you would set the bus width octet value to 4. This is
used internally by the CFI drivers.
- Ignore this option if you use run-time physmap configuration
- (i.e., run-time calling physmap_configure()).

config MTD_PHYSMAP_OF
tristate "Flash device in physical memory map based on OF description"
diff --git a/drivers/mtd/maps/physmap.c b/drivers/mtd/maps/physmap.c
index f64cee4..2174d10 100644
--- a/drivers/mtd/maps/physmap.c
+++ b/drivers/mtd/maps/physmap.c
@@ -245,21 +245,6 @@ static struct platform_device physmap_flash = {
.num_resources = 1,
.resource = &physmap_flash_resource,
};
-
-void physmap_configure(unsigned long addr, unsigned long size,
- int bankwidth, void (*set_vpp)(struct map_info *, int))
-{
- physmap_flash_resource.start = addr;
- physmap_flash_resource.end = addr + size - 1;
- physmap_flash_data.width = bankwidth;
- physmap_flash_data.set_vpp = set_vpp;
-}
-
-void physmap_set_partitions(struct mtd_partition *parts, int num_parts)
-{
- physmap_flash_data.nr_parts = num_parts;
- physmap_flash_data.parts = parts;
-}
#endif

static int __init physmap_init(void)
diff --git a/include/linux/mtd/physmap.h b/include/linux/mtd/physmap.h
index d40bfa1..be4ed0d 100644
--- a/include/linux/mtd/physmap.h
+++ b/include/linux/mtd/physmap.h
@@ -31,21 +31,4 @@ struct physmap_flash_data {
struct mtd_partition *parts;
};

-/*
- * Board needs to specify the exact mapping during their setup time.
- */
-void physmap_configure(unsigned long addr, unsigned long size,
- int bankwidth, void (*set_vpp)(struct map_info *, int) );
-
-/*
- * Machines that wish to do flash partition may want to call this function in
- * their setup routine.
- *
- * physmap_set_partitions(mypartitions, num_parts);
- *
- * Note that one can always override this hard-coded partition with
- * command line partition (you need to enable CONFIG_MTD_CMDLINE_PARTS).
- */
-void physmap_set_partitions(struct mtd_partition *parts, int num_parts);
-
#endif /* __LINUX_MTD_PHYSMAP__ */
--
1.7.4.4