From: Miquel Raynal <miquel.raynal@bootlin.com>
To: Tudor Ambarus <tudor.ambarus@linaro.org>
Cc: Mark Brown <broonie@kernel.org>,
Richard Weinberger <richard@nod.at>,
Vignesh Raghavendra <vigneshr@ti.com>,
Pratyush Yadav <pratyush@kernel.org>,
Thomas Petazzoni <thomas.petazzoni@bootlin.com>,
Steam Lin <STLin2@winbond.com>, Santhosh Kumar K <s-k6@ti.com>,
linux-spi@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-mtd@lists.infradead.org
Subject: Re: [PATCH 11/28] mtd: spinand: Convert vendor drivers to SPINAND_OP()
Date: Wed, 19 Nov 2025 18:24:47 +0100 [thread overview]
Message-ID: <87ecpuaqao.fsf@bootlin.com> (raw)
In-Reply-To: <d77310d9-f865-45cf-90ae-ff542cd1140f@linaro.org> (Tudor Ambarus's message of "Wed, 5 Nov 2025 17:30:20 +0100")
On 05/11/2025 at 17:30:20 +01, Tudor Ambarus <tudor.ambarus@linaro.org> wrote:
> On 10/31/25 6:26 PM, Miquel Raynal wrote:
>> This macro allows to silently switch bus interfaces, use it outside of
>> the core in all places that can be trivially converted.
>>
>> At this stage there is no functional change expected, until octal DTR
>> support gets added.
>>
>
> Shouldn't this be squashed to the previous patch?
That's right, there is no strong reason to do it in two patches. I think
this comes from the order in which I progressively converted the
drivers, I'll squash.
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
next prev parent reply other threads:[~2025-11-19 17:24 UTC|newest]
Thread overview: 51+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-10-31 17:26 [PATCH 00/28] mtd: spinand: Octal DTR support Miquel Raynal
2025-10-31 17:26 ` [PATCH 01/28] spi: spi-mem: Make the DTR command operation macro more suitable Miquel Raynal
2025-11-05 15:35 ` Tudor Ambarus
2025-10-31 17:26 ` [PATCH 02/28] spi: spi-mem: Create a repeated address operation Miquel Raynal
2025-11-05 15:43 ` Tudor Ambarus
2025-11-19 17:10 ` Miquel Raynal
2025-11-20 8:49 ` Tudor Ambarus
2025-10-31 17:26 ` [PATCH 03/28] spi: spi-mem: Limit octal DTR constraints to octal DTR situations Miquel Raynal
2025-11-05 15:53 ` Tudor Ambarus
2025-10-31 17:26 ` [PATCH 04/28] mtd: spinand: Fix kernel doc Miquel Raynal
2025-11-05 15:57 ` Tudor Ambarus
2025-11-19 17:18 ` Miquel Raynal
2025-11-20 8:05 ` Tudor Ambarus
2025-10-31 17:26 ` [PATCH 05/28] mtd: spinand: Add missing check Miquel Raynal
2025-11-05 16:04 ` Tudor Ambarus
2025-10-31 17:26 ` [PATCH 06/28] mtd: spinand: Remove stale definitions Miquel Raynal
2025-11-05 16:05 ` Tudor Ambarus
2025-10-31 17:26 ` [PATCH 07/28] mtd: spinand: Use standard return values Miquel Raynal
2025-11-05 16:06 ` Tudor Ambarus
2025-11-19 17:20 ` Miquel Raynal
2025-10-31 17:26 ` [PATCH 08/28] mtd: spinand: Decouple write enable and write disable operations Miquel Raynal
2025-11-05 16:08 ` Tudor Ambarus
2025-10-31 17:26 ` [PATCH 09/28] mtd: spinand: Create an array of operation templates Miquel Raynal
2025-11-05 16:17 ` Tudor Ambarus
2025-10-31 17:26 ` [PATCH 10/28] mtd: spinand: Make use of the operation templates through SPINAND_OP() Miquel Raynal
2025-11-05 16:28 ` Tudor Ambarus
2025-11-19 17:23 ` Miquel Raynal
2025-11-20 8:35 ` Tudor Ambarus
2025-10-31 17:26 ` [PATCH 11/28] mtd: spinand: Convert vendor drivers to SPINAND_OP() Miquel Raynal
2025-11-05 16:30 ` Tudor Ambarus
2025-11-19 17:24 ` Miquel Raynal [this message]
2025-10-31 17:26 ` [PATCH 12/28] mtd: spinand: macronix: Convert vendor specific operation " Miquel Raynal
2025-11-05 16:40 ` Tudor Ambarus
2025-10-31 17:26 ` [PATCH 13/28] mtd: spinand: winbond: Convert W25N " Miquel Raynal
2025-11-05 16:40 ` Tudor Ambarus
2025-10-31 17:26 ` [PATCH 14/28] mtd: spinand: winbond: Convert W35N " Miquel Raynal
2025-11-05 16:41 ` Tudor Ambarus
2025-10-31 17:26 ` [PATCH 15/28] mtd: spinand: List vendor specific operations and make sure they are supported Miquel Raynal
2025-10-31 17:27 ` [PATCH 16/28] mtd: spinand: macronix: Register vendor specific operation Miquel Raynal
2025-10-31 17:27 ` [PATCH 17/28] mtd: spinand: winbond: Register W25N " Miquel Raynal
2025-10-31 17:27 ` [PATCH 18/28] mtd: spinand: winbond: Register W35N " Miquel Raynal
2025-10-31 17:27 ` [PATCH 19/28] mtd: spinand: winbond: Fix style Miquel Raynal
2025-10-31 17:27 ` [PATCH 20/28] mtd: spinand: winbond: Rename IO_MODE register macro Miquel Raynal
2025-10-31 17:27 ` [PATCH 21/28] mtd: spinand: winbond: Configure the IO mode after the dummy cycles Miquel Raynal
2025-10-31 17:27 ` [PATCH 22/28] mtd: spinand: Gather all the bus interface steps in one single function Miquel Raynal
2025-10-31 17:27 ` [PATCH 23/28] mtd: spinand: Add support for setting a bus interface Miquel Raynal
2025-10-31 17:27 ` [PATCH 24/28] mtd: spinand: Propagate the bus interface across core helpers Miquel Raynal
2025-10-31 17:27 ` [PATCH 25/28] mtd: spinand: Give the bus interface to the configuration helper Miquel Raynal
2025-10-31 17:27 ` [PATCH 26/28] mtd: spinand: Warn if using SSDR-only vendor commands in a non SSDR mode Miquel Raynal
2025-10-31 17:27 ` [PATCH 27/28] mtd: spinand: Add octal DTR support Miquel Raynal
2025-10-31 17:27 ` [PATCH 28/28] mtd: spinand: winbond: W35N " Miquel Raynal
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=87ecpuaqao.fsf@bootlin.com \
--to=miquel.raynal@bootlin.com \
--cc=STLin2@winbond.com \
--cc=broonie@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mtd@lists.infradead.org \
--cc=linux-spi@vger.kernel.org \
--cc=pratyush@kernel.org \
--cc=richard@nod.at \
--cc=s-k6@ti.com \
--cc=thomas.petazzoni@bootlin.com \
--cc=tudor.ambarus@linaro.org \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox