From mboxrd@z Thu Jan 1 00:00:00 1970 Received: from mx07-00178001.pphosted.com ([62.209.51.94]) by bombadil.infradead.org with esmtps (Exim 4.90_1 #2 (Red Hat Linux)) id 1gVDlW-0007on-EE for linux-mtd@lists.infradead.org; Fri, 07 Dec 2018 10:53:55 +0000 Subject: Re: [ v3 2/3] mtd: rawnand: stm32_fmc2: add STM32 FMC2 NAND flash controller driver To: Miquel Raynal CC: , , , , , , , , , , References: <1543509663-26128-1-git-send-email-christophe.kerello@st.com> <1543509663-26128-3-git-send-email-christophe.kerello@st.com> <20181207111808.144fc3f0@xps13> From: Christophe Kerello Message-ID: Date: Fri, 7 Dec 2018 11:53:10 +0100 MIME-Version: 1.0 In-Reply-To: <20181207111808.144fc3f0@xps13> Content-Type: text/plain; charset="utf-8"; format=flowed Content-Language: en-US Content-Transfer-Encoding: 8bit List-Id: Linux MTD discussion mailing list List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , Hi Miquèl, This patchset already takes into account new framework modifications done by Boris (3rd batch of cleanups). The select_chip hook is not used any more in this patchset and exec_op/setup_data_interface hooks have been moved to nand_controller_ops structure. static const struct nand_controller_ops stm32_fmc2_nand_controller_ops = { .attach_chip = stm32_fmc2_attach_chip, .exec_op = stm32_fmc2_exec_op, .setup_data_interface = stm32_fmc2_setup_interface, }; Regards, Christophe Kerello. On 12/7/18 11:18 AM, Miquel Raynal wrote: > Hi Christophe, > > Christophe Kerello wrote on Thu, 29 Nov > 2018 17:41:02 +0100: > >> The driver adds the support for the STMicroelectronics FMC2 NAND >> Controller found on STM32MP SOCs. >> >> This patch is based on FMC2 command sequencer. >> The purpose of the command sequencer is to facilitate the programming >> and the reading of NAND flash pages with the ECC and to free the CPU >> of sequencing tasks. >> It requires one DMA channel for write and two DMA channels for read >> operations. >> >> Only NAND_ECC_HW mode is actually supported. >> The driver supports a maximum 8k page size. >> The following ECC strength and step size are currently supported: >> - nand-ecc-strength = <8>, nand-ecc-step-size = <512> (BCH8) >> - nand-ecc-strength = <4>, nand-ecc-step-size = <512> (BCH4) >> - nand-ecc-strength = <1>, nand-ecc-step-size = <512> (Extended ECC >> based on Hamming) >> >> This patch has been tested on Micron MT29F8G08ABACAH4 and >> MT29F8G16ABACAH4 >> >> Signed-off-by: Christophe Kerello >> --- > > The driver look's good to me. However, Boris contributed new > cleanups that I would like you to take into account before doing > another 'deep' review. Please rebase on top of nand/next and have > a look at the followingcommits. For the ->select_chip() hook, it > should not be exposed anymore and switches should be handled > locally by the driver (you have examples). > > 7a08dbaedd36 mtd: rawnand: Move ->setup_data_interface() to nand_controller_ops > f2abfeb2078b mtd: rawnand: Move the ->exec_op() method to nand_controller_ops > 7d6c37e90cf9 mtd: rawnand: Deprecate the ->select_chip() hook > 1770022ffa85 mtd: rawnand: ams-delta: Stop implementing ->select_chip() > 653c57c7da08 mtd: rawnand: vf610: Stop implementing ->select_chip() > 2ace451cae22 mtd: rawnand: tegra: Stop implementing ->select_chip() > b25251414f6e mtd: rawnand: marvell: Stop implementing ->select_chip() > 550b9fc4e3af mtd: rawnand: fsmc: Stop implementing ->select_chip() > 02b4a52604a4 mtd: rawnand: Make ->select_chip() optional when ->exec_op() is implemented > ae2294b10b0f mtd: rawnand: Pass the CS line to be selected in struct nand_operation > 1d0178593d14 mtd: rawnand: Add nand_[de]select_target() helpers > > While at it, could you also address Linus W. comments. > > Thanks, > Miquèl >