From: Tony Lindgren <tony@atomide.com>
To: linux-omap@vger.kernel.org
Cc: Tony Lindgren <tony@atomide.com>
Subject: [PATCH 3/14] USB: Change omap USB code to use omap_read/write instead of __REG for multi-omap
Date: Tue, 27 May 2008 21:20:07 -0700 [thread overview]
Message-ID: <1211948418-16455-4-git-send-email-tony@atomide.com> (raw)
In-Reply-To: <1211948418-16455-3-git-send-email-tony@atomide.com>
Change omap USB code to use omap_read/write instead of __REG for multi-omap
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap1/board-osk.c | 7 +-
arch/arm/plat-omap/usb.c | 132 ++++++++----
drivers/cbus/tahvo-usb.c | 91 +++++---
drivers/i2c/chips/isp1301_omap.c | 163 ++++++++-----
drivers/i2c/chips/twl4030-usb.c | 39 ++--
drivers/usb/gadget/omap_udc.c | 472 +++++++++++++++++++++-----------------
drivers/usb/gadget/omap_udc.h | 61 +++---
drivers/usb/host/ohci-omap.c | 5 +-
include/asm-arm/arch-omap/usb.h | 23 +-
9 files changed, 586 insertions(+), 407 deletions(-)
diff --git a/arch/arm/mach-omap1/board-osk.c b/arch/arm/mach-omap1/board-osk.c
index a66505f..f2c47b9 100644
--- a/arch/arm/mach-omap1/board-osk.c
+++ b/arch/arm/mach-omap1/board-osk.c
@@ -526,6 +526,8 @@ static void __init osk_mistral_init(void) { }
static void __init osk_init(void)
{
+ u32 l;
+
/* Workaround for wrong CS3 (NOR flash) timing
* There are some U-Boot versions out there which configure
* wrong CS3 memory timings. This mainly leads to CRC
@@ -539,7 +541,10 @@ static void __init osk_init(void)
platform_add_devices(osk5912_devices, ARRAY_SIZE(osk5912_devices));
omap_board_config = osk_config;
omap_board_config_size = ARRAY_SIZE(osk_config);
- USB_TRANSCEIVER_CTRL_REG |= (3 << 1);
+
+ l = omap_readl(USB_TRANSCEIVER_CTRL);
+ l |= (3 << 1);
+ omap_writel(l, USB_TRANSCEIVER_CTRL);
/* irq for tps65010 chip */
/* bootloader effectively does: omap_cfg_reg(U19_1610_MPUIO1); */
diff --git a/arch/arm/plat-omap/usb.c b/arch/arm/plat-omap/usb.c
index a619475..0c4d860 100644
--- a/arch/arm/plat-omap/usb.c
+++ b/arch/arm/plat-omap/usb.c
@@ -156,8 +156,12 @@ static u32 __init omap_usb0_init(unsigned nwires, unsigned is_device)
if (nwires == 0) {
if (cpu_class_is_omap1() && !cpu_is_omap15xx()) {
+ u32 l;
+
/* pulldown D+/D- */
- USB_TRANSCEIVER_CTRL_REG &= ~(3 << 1);
+ l = omap_readl(USB_TRANSCEIVER_CTRL);
+ l &= ~(3 << 1);
+ omap_writel(l, USB_TRANSCEIVER_CTRL);
}
return 0;
}
@@ -171,6 +175,8 @@ static u32 __init omap_usb0_init(unsigned nwires, unsigned is_device)
/* internal transceiver (unavailable on 17xx, 24xx) */
if (!cpu_class_is_omap2() && nwires == 2) {
+ u32 l;
+
// omap_cfg_reg(P9_USB_DP);
// omap_cfg_reg(R8_USB_DM);
@@ -185,9 +191,12 @@ static u32 __init omap_usb0_init(unsigned nwires, unsigned is_device)
* - OTG support on this port not yet written
*/
- USB_TRANSCEIVER_CTRL_REG &= ~(7 << 4);
- if (!is_device)
- USB_TRANSCEIVER_CTRL_REG |= (3 << 1);
+ l = omap_readl(USB_TRANSCEIVER_CTRL);
+ l &= ~(7 << 4);
+ if (!is_device) {
+ l |= (3 << 1);
+ }
+ omap_writel(l, USB_TRANSCEIVER_CTRL);
return 3 << 16;
}
@@ -217,8 +226,13 @@ static u32 __init omap_usb0_init(unsigned nwires, unsigned is_device)
* with VBUS switching and overcurrent detection.
*/
- if (cpu_class_is_omap1() && nwires != 6)
- USB_TRANSCEIVER_CTRL_REG &= ~CONF_USB2_UNI_R;
+ if (cpu_class_is_omap1() && nwires != 6) {
+ u32 l;
+
+ l = omap_readl(USB_TRANSCEIVER_CTRL);
+ l &= ~CONF_USB2_UNI_R;
+ omap_writel(l, USB_TRANSCEIVER_CTRL);
+ }
switch (nwires) {
case 3:
@@ -238,9 +252,13 @@ static u32 __init omap_usb0_init(unsigned nwires, unsigned is_device)
omap_cfg_reg(K20_24XX_USB0_VM);
omap2_usb_devconf_set(0, USB_UNIDIR);
} else {
+ u32 l;
+
omap_cfg_reg(AA9_USB0_VP);
omap_cfg_reg(R9_USB0_VM);
- USB_TRANSCEIVER_CTRL_REG |= CONF_USB2_UNI_R;
+ l = omap_readl(USB_TRANSCEIVER_CTRL);
+ l |= CONF_USB2_UNI_R;
+ omap_writel(l, USB_TRANSCEIVER_CTRL);
}
break;
default:
@@ -254,8 +272,13 @@ static u32 __init omap_usb1_init(unsigned nwires)
{
u32 syscon1 = 0;
- if (cpu_class_is_omap1() && !cpu_is_omap15xx() && nwires != 6)
- USB_TRANSCEIVER_CTRL_REG &= ~CONF_USB1_UNI_R;
+ if (cpu_class_is_omap1() && !cpu_is_omap15xx() && nwires != 6) {
+ u32 l;
+
+ l = omap_readl(USB_TRANSCEIVER_CTRL);
+ l &= ~CONF_USB1_UNI_R;
+ omap_writel(l, USB_TRANSCEIVER_CTRL);
+ }
if (cpu_is_omap24xx())
omap2_usb_devconf_clear(1, USB_BIDIR_TLL);
@@ -316,8 +339,13 @@ static u32 __init omap_usb1_init(unsigned nwires)
syscon1 = 3;
omap_cfg_reg(USB1_VP);
omap_cfg_reg(USB1_VM);
- if (!cpu_is_omap15xx())
- USB_TRANSCEIVER_CTRL_REG |= CONF_USB1_UNI_R;
+ if (!cpu_is_omap15xx()) {
+ u32 l;
+
+ l = omap_readl(USB_TRANSCEIVER_CTRL);
+ l |= CONF_USB1_UNI_R;
+ omap_writel(l, USB_TRANSCEIVER_CTRL);
+ }
break;
default:
bad:
@@ -340,8 +368,13 @@ static u32 __init omap_usb2_init(unsigned nwires, unsigned alt_pingroup)
if (alt_pingroup || nwires == 0)
return 0;
- if (cpu_class_is_omap1() && !cpu_is_omap15xx() && nwires != 6)
- USB_TRANSCEIVER_CTRL_REG &= ~CONF_USB2_UNI_R;
+ if (cpu_class_is_omap1() && !cpu_is_omap15xx() && nwires != 6) {
+ u32 l;
+
+ l = omap_readl(USB_TRANSCEIVER_CTRL);
+ l &= ~CONF_USB2_UNI_R;
+ omap_writel(l, USB_TRANSCEIVER_CTRL);
+ }
/* external transceiver */
if (cpu_is_omap15xx()) {
@@ -410,9 +443,13 @@ static u32 __init omap_usb2_init(unsigned nwires, unsigned alt_pingroup)
omap_cfg_reg(USB2_VP);
omap_cfg_reg(USB2_VM);
} else {
+ u32 l;
+
omap_cfg_reg(AA9_USB2_VP);
omap_cfg_reg(R9_USB2_VM);
- USB_TRANSCEIVER_CTRL_REG |= CONF_USB2_UNI_R;
+ l = omap_readl(USB_TRANSCEIVER_CTRL);
+ l |= CONF_USB2_UNI_R;
+ omap_writel(l, USB_TRANSCEIVER_CTRL);
}
break;
default:
@@ -531,10 +568,6 @@ static struct platform_device otg_device = {
/*-------------------------------------------------------------------------*/
-#define ULPD_CLOCK_CTRL_REG __REG16(ULPD_CLOCK_CTRL)
-#define ULPD_SOFT_REQ_REG __REG16(ULPD_SOFT_REQ)
-
-
// FIXME correct answer depends on hmc_mode,
// as does (on omap1) any nonzero value for config->otg port number
#ifdef CONFIG_USB_GADGET_OMAP
@@ -550,17 +583,17 @@ static struct platform_device otg_device = {
void __init
omap_otg_init(struct omap_usb_config *config)
{
- u32 syscon = OTG_SYSCON_1_REG & 0xffff;
+ u32 syscon;
int status;
int alt_pingroup = 0;
/* NOTE: no bus or clock setup (yet?) */
- syscon = OTG_SYSCON_1_REG & 0xffff;
+ syscon = omap_readl(OTG_SYSCON_1) & 0xffff;
if (!(syscon & OTG_RESET_DONE))
pr_debug("USB resets not complete?\n");
- // OTG_IRQ_EN_REG = 0;
+ //omap_writew(0, OTG_IRQ_EN);
/* pin muxing and transceiver pinouts */
if (config->pins[0] > 2) /* alt pingroup 2 */
@@ -568,8 +601,8 @@ omap_otg_init(struct omap_usb_config *config)
syscon |= omap_usb0_init(config->pins[0], is_usb0_device(config));
syscon |= omap_usb1_init(config->pins[1]);
syscon |= omap_usb2_init(config->pins[2], alt_pingroup);
- pr_debug("OTG_SYSCON_1_REG = %08x\n", syscon);
- OTG_SYSCON_1_REG = syscon;
+ pr_debug("OTG_SYSCON_1 = %08x\n", omap_readl(OTG_SYSCON_1));
+ omap_writel(syscon, OTG_SYSCON_1);
syscon = config->hmc_mode;
syscon |= USBX_SYNCHRO | (4 << 16) /* B_ASE0_BRST */;
@@ -578,9 +611,10 @@ omap_otg_init(struct omap_usb_config *config)
syscon |= OTG_EN;
#endif
if (cpu_class_is_omap1())
- pr_debug("USB_TRANSCEIVER_CTRL_REG = %03x\n", USB_TRANSCEIVER_CTRL_REG);
- pr_debug("OTG_SYSCON_2_REG = %08x\n", syscon);
- OTG_SYSCON_2_REG = syscon;
+ pr_debug("USB_TRANSCEIVER_CTRL = %03x\n",
+ omap_readl(USB_TRANSCEIVER_CTRL));
+ pr_debug("OTG_SYSCON_2 = %08x\n", omap_readl(OTG_SYSCON_2));
+ omap_writel(syscon, OTG_SYSCON_2);
printk("USB: hmc %d", config->hmc_mode);
if (!alt_pingroup)
@@ -597,12 +631,19 @@ omap_otg_init(struct omap_usb_config *config)
printk("\n");
if (cpu_class_is_omap1()) {
+ u16 w;
+
/* leave USB clocks/controllers off until needed */
- ULPD_SOFT_REQ_REG &= ~SOFT_USB_CLK_REQ;
- ULPD_CLOCK_CTRL_REG &= ~USB_MCLK_EN;
- ULPD_CLOCK_CTRL_REG |= DIS_USB_PVCI_CLK;
+ w = omap_readw(ULPD_SOFT_REQ);
+ w &= ~SOFT_USB_CLK_REQ;
+ omap_writew(w, ULPD_SOFT_REQ);
+
+ w = omap_readw(ULPD_CLOCK_CTRL);
+ w &= ~USB_MCLK_EN;
+ w |= DIS_USB_PVCI_CLK;
+ omap_writew(w, ULPD_CLOCK_CTRL);
}
- syscon = OTG_SYSCON_1_REG;
+ syscon = omap_readl(OTG_SYSCON_1);
syscon |= HST_IDLE_EN|DEV_IDLE_EN|OTG_IDLE_EN;
#ifdef CONFIG_USB_GADGET_OMAP
@@ -639,8 +680,8 @@ omap_otg_init(struct omap_usb_config *config)
pr_debug("can't register OTG device, %d\n", status);
}
#endif
- pr_debug("OTG_SYSCON_1_REG = %08x\n", syscon);
- OTG_SYSCON_1_REG = syscon;
+ pr_debug("OTG_SYSCON_1 = %08x\n", omap_readl(OTG_SYSCON_1));
+ omap_writel(syscon, OTG_SYSCON_1);
status = 0;
}
@@ -653,18 +694,19 @@ static inline void omap_otg_init(struct omap_usb_config *config) {}
#ifdef CONFIG_ARCH_OMAP15XX
-#define ULPD_DPLL_CTRL_REG __REG16(ULPD_DPLL_CTRL)
+/* ULPD_DPLL_CTRL */
#define DPLL_IOB (1 << 13)
#define DPLL_PLL_ENABLE (1 << 4)
#define DPLL_LOCK (1 << 0)
-#define ULPD_APLL_CTRL_REG __REG16(ULPD_APLL_CTRL)
+/* ULPD_APLL_CTRL */
#define APLL_NDPLL_SWITCH (1 << 0)
static void __init omap_1510_usb_init(struct omap_usb_config *config)
{
unsigned int val;
+ u16 w;
omap_usb0_init(config->pins[0], is_usb0_device(config));
omap_usb1_init(config->pins[1]);
@@ -685,12 +727,22 @@ static void __init omap_1510_usb_init(struct omap_usb_config *config)
printk("\n");
/* use DPLL for 48 MHz function clock */
- pr_debug("APLL %04x DPLL %04x REQ %04x\n", ULPD_APLL_CTRL_REG,
- ULPD_DPLL_CTRL_REG, ULPD_SOFT_REQ_REG);
- ULPD_APLL_CTRL_REG &= ~APLL_NDPLL_SWITCH;
- ULPD_DPLL_CTRL_REG |= DPLL_IOB | DPLL_PLL_ENABLE;
- ULPD_SOFT_REQ_REG |= SOFT_UDC_REQ | SOFT_DPLL_REQ;
- while (!(ULPD_DPLL_CTRL_REG & DPLL_LOCK))
+ pr_debug("APLL %04x DPLL %04x REQ %04x\n", omap_readw(ULPD_APLL_CTRL),
+ omap_readw(ULPD_DPLL_CTRL), omap_readw(ULPD_SOFT_REQ));
+
+ w = omap_readw(ULPD_APLL_CTRL);
+ w &= ~APLL_NDPLL_SWITCH;
+ omap_writew(w, ULPD_APLL_CTRL);
+
+ w = omap_readw(ULPD_DPLL_CTRL);
+ w |= DPLL_IOB | DPLL_PLL_ENABLE;
+ omap_writew(w, ULPD_DPLL_CTRL);
+
+ w = omap_readw(ULPD_SOFT_REQ);
+ w |= SOFT_UDC_REQ | SOFT_DPLL_REQ;
+ omap_writew(w, ULPD_SOFT_REQ);
+
+ while (!(omap_readw(ULPD_DPLL_CTRL) & DPLL_LOCK))
cpu_relax();
#ifdef CONFIG_USB_GADGET_OMAP
diff --git a/drivers/cbus/tahvo-usb.c b/drivers/cbus/tahvo-usb.c
index 230cf8e..65ea14f 100644
--- a/drivers/cbus/tahvo-usb.c
+++ b/drivers/cbus/tahvo-usb.c
@@ -62,7 +62,7 @@
#define USBR_NSUSPEND (1 << 1)
#define USBR_SEMODE (1 << 0)
-/* bits in OTG_CTRL_REG */
+/* bits in OTG_CTRL */
/* Bits that are controlled by OMAP OTG and are read-only */
#define OTG_CTRL_OMAP_MASK (OTG_PULLDOWN|OTG_PULLUP|OTG_DRV_VBUS|\
@@ -118,27 +118,27 @@ static irqreturn_t omap_otg_irq(int irq, void *arg)
struct tahvo_usb *tu = (struct tahvo_usb *) otg_dev->dev.driver_data;
u16 otg_irq;
- otg_irq = OTG_IRQ_SRC_REG;
+ otg_irq = omap_readw(OTG_IRQ_SRC);
if (otg_irq & OPRT_CHG) {
- OTG_IRQ_SRC_REG = OPRT_CHG;
+ omap_writew(OPRT_CHG, OTG_IRQ_SRC);
} else if (otg_irq & B_SRP_TMROUT) {
- OTG_IRQ_SRC_REG = B_SRP_TMROUT;
+ omap_writew(B_SRP_TMROUT, OTG_IRQ_SRC);
} else if (otg_irq & B_HNP_FAIL) {
- OTG_IRQ_SRC_REG = B_HNP_FAIL;
+ omap_writew(B_HNP_FAIL, OTG_IRQ_SRC);
} else if (otg_irq & A_SRP_DETECT) {
- OTG_IRQ_SRC_REG = A_SRP_DETECT;
+ omap_writew(A_SRP_DETECT, OTG_IRQ_SRC);
} else if (otg_irq & A_REQ_TMROUT) {
- OTG_IRQ_SRC_REG = A_REQ_TMROUT;
+ omap_writew(A_REQ_TMROUT, OTG_IRQ_SRC);
} else if (otg_irq & A_VBUS_ERR) {
- OTG_IRQ_SRC_REG = A_VBUS_ERR;
+ omap_writew(A_VBUS_ERR, OTG_IRQ_SRC);
} else if (otg_irq & DRIVER_SWITCH) {
- if ((!(OTG_CTRL_REG & OTG_DRIVER_SEL)) &&
+ if ((!(omap_readl(OTG_CTRL) & OTG_DRIVER_SEL)) &&
tu->otg.host && tu->otg.state == OTG_STATE_A_HOST) {
/* role is host */
usb_bus_start_enum(tu->otg.host,
tu->otg.host->otg_port);
}
- OTG_IRQ_SRC_REG = DRIVER_SWITCH;
+ omap_writew(DRIVER_SWITCH, OTG_IRQ_SRC);
} else
return IRQ_NONE;
@@ -148,6 +148,7 @@ static irqreturn_t omap_otg_irq(int irq, void *arg)
static int omap_otg_init(void)
{
+ u32 l;
#ifdef CONFIG_USB_OTG
if (!tahvo_otg_dev) {
@@ -155,11 +156,15 @@ static int omap_otg_init(void)
return -ENODEV;
}
#endif
- OTG_SYSCON_1_REG &= ~OTG_IDLE_EN;
+
+ l = omap_readl(OTG_SYSCON_1);
+ l &= ~OTG_IDLE_EN;
+ omap_writel(l, OTG_SYSCON_1);
udelay(100);
/* some of these values are board-specific... */
- OTG_SYSCON_2_REG |= OTG_EN
+ l = omap_readl(OTG_SYSCON_2);
+ l |= OTG_EN
/* for B-device: */
| SRP_GPDATA /* 9msec Bdev D+ pulse */
| SRP_GPDVBUS /* discharge after VBUS pulse */
@@ -168,11 +173,15 @@ static int omap_otg_init(void)
| (0 << 20) /* 200ms nominal A_WAIT_VRISE timer */
| SRP_DPW /* detect 167+ns SRP pulses */
| SRP_DATA | SRP_VBUS; /* accept both kinds of SRP pulse */
+ omap_writel(l, OTG_SYSCON_2);
- OTG_IRQ_EN_REG = DRIVER_SWITCH | OPRT_CHG
+ omap_writew(DRIVER_SWITCH | OPRT_CHG
| B_SRP_TMROUT | B_HNP_FAIL
- | A_VBUS_ERR | A_SRP_DETECT | A_REQ_TMROUT;
- OTG_SYSCON_2_REG |= OTG_EN;
+ | A_VBUS_ERR | A_SRP_DETECT | A_REQ_TMROUT,
+ OTG_IRQ_EN);
+ l = omap_readl(OTG_SYSCON_2);
+ l |= OTG_EN;
+ omap_writel(l, OTG_SYSCON_2);
return 0;
}
@@ -272,6 +281,8 @@ static void check_vbus_state(struct tahvo_usb *tu)
reg = tahvo_read_reg(TAHVO_REG_IDSR);
if (reg & 0x01) {
+ u32 l;
+
vbus_active = 1;
switch (tu->otg.state) {
case OTG_STATE_B_IDLE:
@@ -280,7 +291,10 @@ static void check_vbus_state(struct tahvo_usb *tu)
usb_gadget_vbus_connect(tu->otg.gadget);
/* Set B-session valid and not B-sessio ended to indicate
* Vbus to be ok. */
- OTG_CTRL_REG = (OTG_CTRL_REG & ~OTG_BSESSEND) | OTG_BSESSVLD;
+ l = omap_readl(OTG_CTRL);
+ l &= ~OTG_BSESSEND;
+ l |= OTG_BSESSVLD;
+ omap_writel(l, OTG_CTRL);
tu->otg.state = OTG_STATE_B_PERIPHERAL;
break;
@@ -324,10 +338,10 @@ static void tahvo_usb_become_host(struct tahvo_usb *tu)
* also mark the A-session is always valid */
omap_otg_init();
- l = OTG_CTRL_REG;
- l &= ~(OTG_CTRL_XCVR_MASK|OTG_CTRL_SYS_MASK);
+ l = omap_readl(OTG_CTRL);
+ l &= ~(OTG_CTRL_XCVR_MASK | OTG_CTRL_SYS_MASK);
l |= OTG_ASESSVLD;
- OTG_CTRL_REG = l;
+ omap_writel(l, OTG_CTRL);
/* Power up the transceiver in USB host mode */
tahvo_write_reg(TAHVO_REG_USBR, USBR_REGOUT | USBR_NSUSPEND |
@@ -345,12 +359,16 @@ static void tahvo_usb_stop_host(struct tahvo_usb *tu)
static void tahvo_usb_become_peripheral(struct tahvo_usb *tu)
{
+ u32 l;
+
/* Clear system and transceiver controlled bits
* and enable ID to mark peripheral mode and
* BSESSEND to mark no Vbus */
omap_otg_init();
- OTG_CTRL_REG = (OTG_CTRL_REG & ~(OTG_CTRL_XCVR_MASK|OTG_CTRL_SYS_MASK|OTG_BSESSVLD))
- | OTG_ID | OTG_BSESSEND;
+ l = omap_readl(OTG_CTRL);
+ l &= ~(OTG_CTRL_XCVR_MASK | OTG_CTRL_SYS_MASK | OTG_BSESSVLD);
+ l |= OTG_ID | OTG_BSESSEND;
+ omap_writel(l, OTG_CTRL);
/* Power up transceiver and set it in USB perhiperal mode */
tahvo_write_reg(TAHVO_REG_USBR, USBR_SLAVE_CONTROL | USBR_REGOUT | USBR_NSUSPEND | USBR_SLAVE_SW);
@@ -361,7 +379,13 @@ static void tahvo_usb_become_peripheral(struct tahvo_usb *tu)
static void tahvo_usb_stop_peripheral(struct tahvo_usb *tu)
{
- OTG_CTRL_REG = (OTG_CTRL_REG & ~OTG_BSESSVLD) | OTG_BSESSEND;
+ u32 l;
+
+ l = omap_readl(OTG_CTRL);
+ l &= ~OTG_BSESSVLD;
+ l |= OTG_BSESSEND;
+ omap_writel(l, OTG_CTRL);
+
if (tu->otg.gadget)
usb_gadget_vbus_disconnect(tu->otg.gadget);
tu->otg.state = OTG_STATE_B_IDLE;
@@ -384,15 +408,19 @@ static void tahvo_usb_power_off(struct tahvo_usb *tu)
id = OTG_ID;
else
id = 0;
- l = OTG_CTRL_REG;
+ l = omap_readl(OTG_CTRL);
l &= ~(OTG_CTRL_XCVR_MASK | OTG_CTRL_SYS_MASK | OTG_BSESSVLD);
l |= id | OTG_BSESSEND;
- OTG_CTRL_REG = l;
- OTG_IRQ_EN_REG = 0;
+ omap_writel(l, OTG_CTRL);
+ omap_writew(0, OTG_IRQ_EN);
- OTG_SYSCON_2_REG &= ~OTG_EN;
+ l = omap_readl(OTG_SYSCON_2);
+ l &= ~OTG_EN;
+ omap_writel(l, OTG_SYSCON_2);
- OTG_SYSCON_1_REG |= OTG_IDLE_EN;
+ l = omap_readl(OTG_SYSCON_1);
+ l |= OTG_IDLE_EN;
+ omap_writel(l, OTG_SYSCON_1);
/* Power off transceiver */
tahvo_write_reg(TAHVO_REG_USBR, 0);
@@ -439,13 +467,13 @@ static int tahvo_usb_start_srp(struct otg_transceiver *dev)
if (!dev || tu->otg.state != OTG_STATE_B_IDLE)
return -ENODEV;
- otg_ctrl = OTG_CTRL_REG;
+ otg_ctrl = omap_readl(OTG_CTRL);
if (!(otg_ctrl & OTG_BSESSEND))
return -EINVAL;
otg_ctrl |= OTG_B_BUSREQ;
otg_ctrl &= ~OTG_A_BUSREQ & OTG_CTRL_SYS_MASK;
- OTG_CTRL_REG = otg_ctrl;
+ omap_writel(otg_ctrl, OTG_CTRL);
tu->otg.state = OTG_STATE_B_SRP_INIT;
return 0;
@@ -465,6 +493,7 @@ static int tahvo_usb_start_hnp(struct otg_transceiver *otg)
static int tahvo_usb_set_host(struct otg_transceiver *otg, struct usb_bus *host)
{
struct tahvo_usb *tu = container_of(otg, struct tahvo_usb, otg);
+ u32 l;
dev_dbg(&tu->pt_dev->dev, "set_host %p\n", host);
@@ -483,7 +512,9 @@ static int tahvo_usb_set_host(struct otg_transceiver *otg, struct usb_bus *host)
return 0;
}
- OTG_SYSCON_1_REG &= ~(OTG_IDLE_EN | HST_IDLE_EN | DEV_IDLE_EN);
+ l = omap_readl(OTG_SYSCON_1);
+ l &= ~(OTG_IDLE_EN | HST_IDLE_EN | DEV_IDLE_EN);
+ omap_writel(l, OTG_SYSCON_1);
if (TAHVO_MODE(tu) == TAHVO_MODE_HOST) {
tu->otg.host = NULL;
diff --git a/drivers/i2c/chips/isp1301_omap.c b/drivers/i2c/chips/isp1301_omap.c
index 135ffb8..7a5dcfb 100644
--- a/drivers/i2c/chips/isp1301_omap.c
+++ b/drivers/i2c/chips/isp1301_omap.c
@@ -70,7 +70,7 @@ struct isp1301 {
};
-/* bits in OTG_CTRL_REG */
+/* bits in OTG_CTRL */
#define OTG_XCEIV_OUTPUTS \
(OTG_ASESSVLD|OTG_BSESSEND|OTG_BSESSVLD|OTG_VBUSVLD|OTG_ID)
@@ -187,8 +187,8 @@ isp1301_clear_bits(struct isp1301 *isp, u8 reg, u8 bits)
/* operational registers */
#define ISP1301_MODE_CONTROL_1 0x04 /* u8 read, set, +1 clear */
-# define MC1_SPEED_REG (1 << 0)
-# define MC1_SUSPEND_REG (1 << 1)
+# define MC1_SPEED (1 << 0)
+# define MC1_SUSPEND (1 << 1)
# define MC1_DAT_SE0 (1 << 2)
# define MC1_TRANSPARENT (1 << 3)
# define MC1_BDIS_ACON_EN (1 << 4)
@@ -275,7 +275,7 @@ static void power_down(struct isp1301 *isp)
isp->otg.state = OTG_STATE_UNDEFINED;
// isp1301_set_bits(isp, ISP1301_MODE_CONTROL_2, MC2_GLOBAL_PWR_DN);
- isp1301_set_bits(isp, ISP1301_MODE_CONTROL_1, MC1_SUSPEND_REG);
+ isp1301_set_bits(isp, ISP1301_MODE_CONTROL_1, MC1_SUSPEND);
isp1301_clear_bits(isp, ISP1301_OTG_CONTROL_1, OTG1_ID_PULLDOWN);
isp1301_clear_bits(isp, ISP1301_MODE_CONTROL_1, MC1_DAT_SE0);
@@ -284,7 +284,7 @@ static void power_down(struct isp1301 *isp)
static void power_up(struct isp1301 *isp)
{
// isp1301_clear_bits(isp, ISP1301_MODE_CONTROL_2, MC2_GLOBAL_PWR_DN);
- isp1301_clear_bits(isp, ISP1301_MODE_CONTROL_1, MC1_SUSPEND_REG);
+ isp1301_clear_bits(isp, ISP1301_MODE_CONTROL_1, MC1_SUSPEND);
/* do this only when cpu is driving transceiver,
* so host won't see a low speed device...
@@ -361,6 +361,8 @@ isp1301_defer_work(struct isp1301 *isp, int work)
/* called from irq handlers */
static void a_idle(struct isp1301 *isp, const char *tag)
{
+ u32 l;
+
if (isp->otg.state == OTG_STATE_A_IDLE)
return;
@@ -374,13 +376,17 @@ static void a_idle(struct isp1301 *isp, const char *tag)
gadget_suspend(isp);
}
isp->otg.state = OTG_STATE_A_IDLE;
- isp->last_otg_ctrl = OTG_CTRL_REG = OTG_CTRL_REG & OTG_XCEIV_OUTPUTS;
+ l = omap_readl(OTG_CTRL) & OTG_XCEIV_OUTPUTS;
+ omap_writel(l, OTG_CTRL);
+ isp->last_otg_ctrl = l;
pr_debug(" --> %s/%s\n", state_name(isp), tag);
}
/* called from irq handlers */
static void b_idle(struct isp1301 *isp, const char *tag)
{
+ u32 l;
+
if (isp->otg.state == OTG_STATE_B_IDLE)
return;
@@ -394,7 +400,9 @@ static void b_idle(struct isp1301 *isp, const char *tag)
gadget_suspend(isp);
}
isp->otg.state = OTG_STATE_B_IDLE;
- isp->last_otg_ctrl = OTG_CTRL_REG = OTG_CTRL_REG & OTG_XCEIV_OUTPUTS;
+ l = omap_readl(OTG_CTRL) & OTG_XCEIV_OUTPUTS;
+ omap_writel(l, OTG_CTRL);
+ isp->last_otg_ctrl = l;
pr_debug(" --> %s/%s\n", state_name(isp), tag);
}
@@ -407,7 +415,7 @@ dump_regs(struct isp1301 *isp, const char *label)
u8 src = isp1301_get_u8(isp, ISP1301_INTERRUPT_SOURCE);
pr_debug("otg: %06x, %s %s, otg/%02x stat/%02x.%02x\n",
- OTG_CTRL_REG, label, state_name(isp),
+ omap_readl(OTG_CTRL), label, state_name(isp),
ctrl, status, src);
/* mode control and irq enables don't change much */
#endif
@@ -430,7 +438,7 @@ dump_regs(struct isp1301 *isp, const char *label)
static void check_state(struct isp1301 *isp, const char *tag)
{
enum usb_otg_state state = OTG_STATE_UNDEFINED;
- u8 fsm = OTG_TEST_REG & 0x0ff;
+ u8 fsm = omap_readw(OTG_TEST) & 0x0ff;
unsigned extra = 0;
switch (fsm) {
@@ -495,7 +503,8 @@ static void check_state(struct isp1301 *isp, const char *tag)
if (isp->otg.state == state && !extra)
return;
pr_debug("otg: %s FSM %s/%02x, %s, %06x\n", tag,
- state_string(state), fsm, state_name(isp), OTG_CTRL_REG);
+ state_string(state), fsm, state_name(isp),
+ omap_readl(OTG_CTRL));
}
#else
@@ -510,10 +519,11 @@ static void update_otg1(struct isp1301 *isp, u8 int_src)
u32 otg_ctrl;
u8 int_id;
- otg_ctrl = OTG_CTRL_REG
- & OTG_CTRL_MASK
- & ~OTG_XCEIV_INPUTS
- & ~(OTG_ID|OTG_ASESSVLD|OTG_VBUSVLD);
+ otg_ctrl = omap_readl(OTG_CTRL) & OTG_CTRL_MASK;
+ otg_ctrl &= ~OTG_XCEIV_INPUTS;
+ otg_ctrl &= ~(OTG_ID|OTG_ASESSVLD|OTG_VBUSVLD);
+
+
if (int_src & INTR_SESS_VLD)
otg_ctrl |= OTG_ASESSVLD;
else if (isp->otg.state == OTG_STATE_A_WAIT_VFALL) {
@@ -539,7 +549,7 @@ static void update_otg1(struct isp1301 *isp, u8 int_src)
return;
}
}
- OTG_CTRL_REG = otg_ctrl;
+ omap_writel(otg_ctrl, OTG_CTRL);
}
/* outputs from ISP1301_OTG_STATUS */
@@ -547,15 +557,14 @@ static void update_otg2(struct isp1301 *isp, u8 otg_status)
{
u32 otg_ctrl;
- otg_ctrl = OTG_CTRL_REG
- & OTG_CTRL_MASK
- & ~OTG_XCEIV_INPUTS
- & ~(OTG_BSESSVLD|OTG_BSESSEND);
+ otg_ctrl = omap_readl(OTG_CTRL) & OTG_CTRL_MASK;
+ otg_ctrl &= ~OTG_XCEIV_INPUTS;
+ otg_ctrl &= ~(OTG_BSESSVLD | OTG_BSESSEND);
if (otg_status & OTG_B_SESS_VLD)
otg_ctrl |= OTG_BSESSVLD;
else if (otg_status & OTG_B_SESS_END)
otg_ctrl |= OTG_BSESSEND;
- OTG_CTRL_REG = otg_ctrl;
+ omap_writel(otg_ctrl, OTG_CTRL);
}
/* inputs going to ISP1301 */
@@ -564,7 +573,7 @@ static void otg_update_isp(struct isp1301 *isp)
u32 otg_ctrl, otg_change;
u8 set = OTG1_DM_PULLDOWN, clr = OTG1_DM_PULLUP;
- otg_ctrl = OTG_CTRL_REG;
+ otg_ctrl = omap_readl(OTG_CTRL);
otg_change = otg_ctrl ^ isp->last_otg_ctrl;
isp->last_otg_ctrl = otg_ctrl;
otg_ctrl = otg_ctrl & OTG_XCEIV_INPUTS;
@@ -644,6 +653,8 @@ pulldown:
/* HNP switch to host or peripheral; and SRP */
if (otg_change & OTG_PULLUP) {
+ u32 l;
+
switch (isp->otg.state) {
case OTG_STATE_B_IDLE:
if (clr & OTG1_DP_PULLUP)
@@ -660,7 +671,9 @@ pulldown:
default:
break;
}
- OTG_CTRL_REG |= OTG_PULLUP;
+ l = omap_readl(OTG_CTRL);
+ l |= OTG_PULLUP;
+ omap_writel(l, OTG_CTRL);
}
check_state(isp, __func__);
@@ -669,20 +682,20 @@ pulldown:
static irqreturn_t omap_otg_irq(int irq, void *_isp)
{
- u16 otg_irq = OTG_IRQ_SRC_REG;
+ u16 otg_irq = omap_readw(OTG_IRQ_SRC);
u32 otg_ctrl;
int ret = IRQ_NONE;
struct isp1301 *isp = _isp;
/* update ISP1301 transciever from OTG controller */
if (otg_irq & OPRT_CHG) {
- OTG_IRQ_SRC_REG = OPRT_CHG;
+ omap_writew(OPRT_CHG, OTG_IRQ_SRC);
isp1301_defer_work(isp, WORK_UPDATE_ISP);
ret = IRQ_HANDLED;
/* SRP to become b_peripheral failed */
} else if (otg_irq & B_SRP_TMROUT) {
- pr_debug("otg: B_SRP_TIMEOUT, %06x\n", OTG_CTRL_REG);
+ pr_debug("otg: B_SRP_TIMEOUT, %06x\n", omap_readl(OTG_CTRL));
notresponding(isp);
/* gadget drivers that care should monitor all kinds of
@@ -692,31 +705,31 @@ static irqreturn_t omap_otg_irq(int irq, void *_isp)
if (isp->otg.state == OTG_STATE_B_SRP_INIT)
b_idle(isp, "srp_timeout");
- OTG_IRQ_SRC_REG = B_SRP_TMROUT;
+ omap_writew(B_SRP_TMROUT, OTG_IRQ_SRC);
ret = IRQ_HANDLED;
/* HNP to become b_host failed */
} else if (otg_irq & B_HNP_FAIL) {
pr_debug("otg: %s B_HNP_FAIL, %06x\n",
- state_name(isp), OTG_CTRL_REG);
+ state_name(isp), omap_readl(OTG_CTRL));
notresponding(isp);
- otg_ctrl = OTG_CTRL_REG;
+ otg_ctrl = omap_readl(OTG_CTRL);
otg_ctrl |= OTG_BUSDROP;
otg_ctrl &= OTG_CTRL_MASK & ~OTG_XCEIV_INPUTS;
- OTG_CTRL_REG = otg_ctrl;
+ omap_writel(otg_ctrl, OTG_CTRL);
/* subset of b_peripheral()... */
isp->otg.state = OTG_STATE_B_PERIPHERAL;
pr_debug(" --> b_peripheral\n");
- OTG_IRQ_SRC_REG = B_HNP_FAIL;
+ omap_writew(B_HNP_FAIL, OTG_IRQ_SRC);
ret = IRQ_HANDLED;
/* detect SRP from B-device ... */
} else if (otg_irq & A_SRP_DETECT) {
pr_debug("otg: %s SRP_DETECT, %06x\n",
- state_name(isp), OTG_CTRL_REG);
+ state_name(isp), omap_readl(OTG_CTRL));
isp1301_defer_work(isp, WORK_UPDATE_OTG);
switch (isp->otg.state) {
@@ -724,49 +737,49 @@ static irqreturn_t omap_otg_irq(int irq, void *_isp)
if (!isp->otg.host)
break;
isp1301_defer_work(isp, WORK_HOST_RESUME);
- otg_ctrl = OTG_CTRL_REG;
+ otg_ctrl = omap_readl(OTG_CTRL);
otg_ctrl |= OTG_A_BUSREQ;
otg_ctrl &= ~(OTG_BUSDROP|OTG_B_BUSREQ)
& ~OTG_XCEIV_INPUTS
& OTG_CTRL_MASK;
- OTG_CTRL_REG = otg_ctrl;
+ omap_writel(otg_ctrl, OTG_CTRL);
break;
default:
break;
}
- OTG_IRQ_SRC_REG = A_SRP_DETECT;
+ omap_writew(A_SRP_DETECT, OTG_IRQ_SRC);
ret = IRQ_HANDLED;
/* timer expired: T(a_wait_bcon) and maybe T(a_wait_vrise)
* we don't track them separately
*/
} else if (otg_irq & A_REQ_TMROUT) {
- otg_ctrl = OTG_CTRL_REG;
+ otg_ctrl = omap_readl(OTG_CTRL);
pr_info("otg: BCON_TMOUT from %s, %06x\n",
state_name(isp), otg_ctrl);
notresponding(isp);
otg_ctrl |= OTG_BUSDROP;
otg_ctrl &= ~OTG_A_BUSREQ & OTG_CTRL_MASK & ~OTG_XCEIV_INPUTS;
- OTG_CTRL_REG = otg_ctrl;
+ omap_writel(otg_ctrl, OTG_CTRL);
isp->otg.state = OTG_STATE_A_WAIT_VFALL;
- OTG_IRQ_SRC_REG = A_REQ_TMROUT;
+ omap_writew(A_REQ_TMROUT, OTG_IRQ_SRC);
ret = IRQ_HANDLED;
/* A-supplied voltage fell too low; overcurrent */
} else if (otg_irq & A_VBUS_ERR) {
- otg_ctrl = OTG_CTRL_REG;
+ otg_ctrl = omap_readl(OTG_CTRL);
printk(KERN_ERR "otg: %s, VBUS_ERR %04x ctrl %06x\n",
state_name(isp), otg_irq, otg_ctrl);
otg_ctrl |= OTG_BUSDROP;
otg_ctrl &= ~OTG_A_BUSREQ & OTG_CTRL_MASK & ~OTG_XCEIV_INPUTS;
- OTG_CTRL_REG = otg_ctrl;
+ omap_writel(otg_ctrl, OTG_CTRL);
isp->otg.state = OTG_STATE_A_VBUS_ERR;
- OTG_IRQ_SRC_REG = A_VBUS_ERR;
+ omap_writew(A_VBUS_ERR, OTG_IRQ_SRC);
ret = IRQ_HANDLED;
/* switch driver; the transciever code activates it,
@@ -775,7 +788,7 @@ static irqreturn_t omap_otg_irq(int irq, void *_isp)
} else if (otg_irq & DRIVER_SWITCH) {
int kick = 0;
- otg_ctrl = OTG_CTRL_REG;
+ otg_ctrl = omap_readl(OTG_CTRL);
printk(KERN_NOTICE "otg: %s, SWITCH to %s, ctrl %06x\n",
state_name(isp),
(otg_ctrl & OTG_DRIVER_SEL)
@@ -798,7 +811,7 @@ static irqreturn_t omap_otg_irq(int irq, void *_isp)
} else {
if (!(otg_ctrl & OTG_ID)) {
otg_ctrl &= OTG_CTRL_MASK & ~OTG_XCEIV_INPUTS;
- OTG_CTRL_REG = otg_ctrl | OTG_A_BUSREQ;
+ omap_writel(otg_ctrl | OTG_A_BUSREQ, OTG_CTRL);
}
if (isp->otg.host) {
@@ -823,7 +836,7 @@ static irqreturn_t omap_otg_irq(int irq, void *_isp)
}
}
- OTG_IRQ_SRC_REG = DRIVER_SWITCH;
+ omap_writew(DRIVER_SWITCH, OTG_IRQ_SRC);
ret = IRQ_HANDLED;
if (kick)
@@ -839,12 +852,15 @@ static struct platform_device *otg_dev;
static int otg_init(struct isp1301 *isp)
{
+ u32 l;
+
if (!otg_dev)
return -ENODEV;
dump_regs(isp, __func__);
/* some of these values are board-specific... */
- OTG_SYSCON_2_REG |= OTG_EN
+ l = omap_readl(OTG_SYSCON_2);
+ l |= OTG_EN
/* for B-device: */
| SRP_GPDATA /* 9msec Bdev D+ pulse */
| SRP_GPDVBUS /* discharge after VBUS pulse */
@@ -854,18 +870,22 @@ static int otg_init(struct isp1301 *isp)
| SRP_DPW /* detect 167+ns SRP pulses */
| SRP_DATA | SRP_VBUS /* accept both kinds of SRP pulse */
;
+ omap_writel(l, OTG_SYSCON_2);
update_otg1(isp, isp1301_get_u8(isp, ISP1301_INTERRUPT_SOURCE));
update_otg2(isp, isp1301_get_u8(isp, ISP1301_OTG_STATUS));
check_state(isp, __func__);
pr_debug("otg: %s, %s %06x\n",
- state_name(isp), __func__, OTG_CTRL_REG);
+ state_name(isp), __func__, omap_readl(OTG_CTRL));
- OTG_IRQ_EN_REG = DRIVER_SWITCH | OPRT_CHG
+ omap_writew(DRIVER_SWITCH | OPRT_CHG
| B_SRP_TMROUT | B_HNP_FAIL
- | A_VBUS_ERR | A_SRP_DETECT | A_REQ_TMROUT;
- OTG_SYSCON_2_REG |= OTG_EN;
+ | A_VBUS_ERR | A_SRP_DETECT | A_REQ_TMROUT, OTG_IRQ_EN);
+
+ l = omap_readl(OTG_SYSCON_2);
+ l |= OTG_EN;
+ omap_writel(l, OTG_SYSCON_2);
return 0;
}
@@ -932,7 +952,11 @@ static void otg_unbind(struct isp1301 *isp)
static void b_peripheral(struct isp1301 *isp)
{
- OTG_CTRL_REG = OTG_CTRL_REG & OTG_XCEIV_OUTPUTS;
+ u32 l;
+
+ l = omap_readl(OTG_CTRL) & OTG_XCEIV_OUTPUTS;
+ omap_writel(l, OTG_CTRL);
+
usb_gadget_vbus_connect(isp->otg.gadget);
#ifdef CONFIG_USB_OTG
@@ -1004,6 +1028,8 @@ static void isp_update_otg(struct isp1301 *isp, u8 stat)
isp_bstat = 0;
}
} else {
+ u32 l;
+
/* if user unplugged mini-A end of cable,
* don't bypass A_WAIT_VFALL.
*/
@@ -1024,8 +1050,9 @@ static void isp_update_otg(struct isp1301 *isp, u8 stat)
isp1301_clear_bits(isp, ISP1301_MODE_CONTROL_1,
MC1_BDIS_ACON_EN);
isp->otg.state = OTG_STATE_B_IDLE;
- OTG_CTRL_REG &= OTG_CTRL_REG & OTG_CTRL_MASK
- & ~OTG_CTRL_BITS;
+ l = omap_readl(OTG_CTRL) & OTG_CTRL_MASK;
+ l &= ~OTG_CTRL_BITS;
+ omap_writel(l, OTG_CTRL);
break;
case OTG_STATE_B_IDLE:
break;
@@ -1051,7 +1078,8 @@ static void isp_update_otg(struct isp1301 *isp, u8 stat)
/* FALLTHROUGH */
case OTG_STATE_B_SRP_INIT:
b_idle(isp, __func__);
- OTG_CTRL_REG &= OTG_CTRL_REG & OTG_XCEIV_OUTPUTS;
+ l = omap_readl(OTG_CTRL) & OTG_XCEIV_OUTPUTS;
+ omap_writel(l, OTG_CTRL);
/* FALLTHROUGH */
case OTG_STATE_B_IDLE:
if (isp->otg.gadget && (isp_bstat & OTG_B_SESS_VLD)) {
@@ -1135,11 +1163,11 @@ isp1301_work(struct work_struct *work)
case OTG_STATE_A_WAIT_VRISE:
isp->otg.state = OTG_STATE_A_HOST;
pr_debug(" --> a_host\n");
- otg_ctrl = OTG_CTRL_REG;
+ otg_ctrl = omap_readl(OTG_CTRL);
otg_ctrl |= OTG_A_BUSREQ;
otg_ctrl &= ~(OTG_BUSDROP|OTG_B_BUSREQ)
& OTG_CTRL_MASK;
- OTG_CTRL_REG = otg_ctrl;
+ omap_writel(otg_ctrl, OTG_CTRL);
break;
case OTG_STATE_B_WAIT_ACON:
isp->otg.state = OTG_STATE_B_HOST;
@@ -1278,7 +1306,7 @@ isp1301_set_host(struct otg_transceiver *otg, struct usb_bus *host)
return -ENODEV;
if (!host) {
- OTG_IRQ_EN_REG = 0;
+ omap_writew(0, OTG_IRQ_EN);
power_down(isp);
isp->otg.host = 0;
return 0;
@@ -1326,12 +1354,13 @@ static int
isp1301_set_peripheral(struct otg_transceiver *otg, struct usb_gadget *gadget)
{
struct isp1301 *isp = container_of(otg, struct isp1301, otg);
+ u32 l;
if (!otg || isp != the_transceiver)
return -ENODEV;
if (!gadget) {
- OTG_IRQ_EN_REG = 0;
+ omap_writew(0, OTG_IRQ_EN);
if (!isp->otg.default_a)
enable_vbus_draw(isp, 0);
usb_gadget_vbus_disconnect(isp->otg.gadget);
@@ -1352,9 +1381,11 @@ isp1301_set_peripheral(struct otg_transceiver *otg, struct usb_gadget *gadget)
isp->otg.gadget = gadget;
// FIXME update its refcount
- OTG_CTRL_REG = (OTG_CTRL_REG & OTG_CTRL_MASK
- & ~(OTG_XCEIV_OUTPUTS|OTG_CTRL_BITS))
- | OTG_ID;
+ l = omap_readl(OTG_CTRL) & OTG_CTRL_MASK;
+ l &= ~(OTG_XCEIV_OUTPUTS|OTG_CTRL_BITS);
+ l |= OTG_ID;
+ omap_writel(l, OTG_CTRL);
+
power_up(isp);
isp->otg.state = OTG_STATE_B_IDLE;
@@ -1407,16 +1438,17 @@ isp1301_start_srp(struct otg_transceiver *dev)
|| isp->otg.state != OTG_STATE_B_IDLE)
return -ENODEV;
- otg_ctrl = OTG_CTRL_REG;
+ otg_ctrl = omap_readl(OTG_CTRL);
if (!(otg_ctrl & OTG_BSESSEND))
return -EINVAL;
otg_ctrl |= OTG_B_BUSREQ;
otg_ctrl &= ~OTG_A_BUSREQ & OTG_CTRL_MASK;
- OTG_CTRL_REG = otg_ctrl;
+ omap_writel(otg_ctrl, OTG_CTRL);
isp->otg.state = OTG_STATE_B_SRP_INIT;
- pr_debug("otg: SRP, %s ... %06x\n", state_name(isp), OTG_CTRL_REG);
+ pr_debug("otg: SRP, %s ... %06x\n", state_name(isp),
+ omap_readl(OTG_CTRL));
#ifdef CONFIG_USB_OTG
check_state(isp, __func__);
#endif
@@ -1428,6 +1460,7 @@ isp1301_start_hnp(struct otg_transceiver *dev)
{
#ifdef CONFIG_USB_OTG
struct isp1301 *isp = container_of(dev, struct isp1301, otg);
+ u32 l;
if (!dev || isp != the_transceiver)
return -ENODEV;
@@ -1458,7 +1491,9 @@ isp1301_start_hnp(struct otg_transceiver *dev)
#endif
/* caller must suspend then clear A_BUSREQ */
usb_gadget_vbus_connect(isp->otg.gadget);
- OTG_CTRL_REG |= OTG_A_SETB_HNPEN;
+ l = omap_readl(OTG_CTRL);
+ l |= OTG_A_SETB_HNPEN;
+ omap_writel(l, OTG_CTRL);
break;
case OTG_STATE_A_PERIPHERAL:
@@ -1468,7 +1503,7 @@ isp1301_start_hnp(struct otg_transceiver *dev)
return -EILSEQ;
}
pr_debug("otg: HNP %s, %06x ...\n",
- state_name(isp), OTG_CTRL_REG);
+ state_name(isp), omap_readl(OTG_CTRL));
check_state(isp, __func__);
return 0;
#else
diff --git a/drivers/i2c/chips/twl4030-usb.c b/drivers/i2c/chips/twl4030-usb.c
index 041ae60..7f93b4f 100644
--- a/drivers/i2c/chips/twl4030-usb.c
+++ b/drivers/i2c/chips/twl4030-usb.c
@@ -67,15 +67,15 @@
#define IFC_CTRL_CARKITMODE (1 << 2)
#define IFC_CTRL_FSLSSERIALMODE_3PIN (1 << 1)
-#define OTG_CTRL 0x0A
-#define OTG_CTRL_SET 0x0B
-#define OTG_CTRL_CLR 0x0C
-#define OTG_CTRL_DRVVBUS (1 << 5)
-#define OTG_CTRL_CHRGVBUS (1 << 4)
-#define OTG_CTRL_DISCHRGVBUS (1 << 3)
-#define OTG_CTRL_DMPULLDOWN (1 << 2)
-#define OTG_CTRL_DPPULLDOWN (1 << 1)
-#define OTG_CTRL_IDPULLUP (1 << 0)
+#define TWL4030_OTG_CTRL 0x0A
+#define TWL4030_OTG_CTRL_SET 0x0B
+#define TWL4030_OTG_CTRL_CLR 0x0C
+#define TWL4030_OTG_CTRL_DRVVBUS (1 << 5)
+#define TWL4030_OTG_CTRL_CHRGVBUS (1 << 4)
+#define TWL4030_OTG_CTRL_DISCHRGVBUS (1 << 3)
+#define TWL4030_OTG_CTRL_DMPULLDOWN (1 << 2)
+#define TWL4030_OTG_CTRL_DPPULLDOWN (1 << 1)
+#define TWL4030_OTG_CTRL_IDPULLUP (1 << 0)
#define USB_INT_EN_RISE 0x0D
#define USB_INT_EN_RISE_SET 0x0E
@@ -253,7 +253,7 @@
/* internal define on top of container_of */
#define xceiv_to_twl(x) container_of((x), struct twl4030_usb, otg);
-/* bits in OTG_CTRL_REG */
+/* bits in OTG_CTRL */
#define OTG_XCEIV_OUTPUTS \
(OTG_ASESSVLD|OTG_BSESSEND|OTG_BSESSVLD|OTG_VBUSVLD|OTG_ID)
@@ -626,12 +626,13 @@ static int twl4030_set_peripheral(struct otg_transceiver *xceiv,
struct usb_gadget *gadget)
{
struct twl4030_usb *twl = xceiv_to_twl(xceiv);
+ u32 l;
if (!xceiv)
return -ENODEV;
if (!gadget) {
- OTG_IRQ_EN_REG = 0;
+ omap_writew(0, OTG_IRQ_EN);
twl4030_phy_suspend(1);
twl->otg.gadget = NULL;
@@ -641,9 +642,10 @@ static int twl4030_set_peripheral(struct otg_transceiver *xceiv,
twl->otg.gadget = gadget;
twl4030_phy_resume();
- OTG_CTRL_REG = (OTG_CTRL_REG & OTG_CTRL_MASK
- & ~(OTG_XCEIV_OUTPUTS|OTG_CTRL_BITS))
- | OTG_ID;
+ l = omap_readl(OTG_CTRL) & OTG_CTRL_MASK;
+ l &= ~(OTG_XCEIV_OUTPUTS|OTG_CTRL_BITS);
+ l |= OTG_ID;
+ omap_writel(l, OTG_CTRL);
twl->otg.state = OTG_STATE_B_IDLE;
@@ -663,7 +665,7 @@ static int twl4030_set_host(struct otg_transceiver *xceiv, struct usb_bus *host)
return -ENODEV;
if (!host) {
- OTG_IRQ_EN_REG = 0;
+ omap_writew(0, OTG_IRQ_EN);
twl4030_phy_suspend(1);
twl->otg.host = NULL;
@@ -673,12 +675,13 @@ static int twl4030_set_host(struct otg_transceiver *xceiv, struct usb_bus *host)
twl->otg.host = host;
twl4030_phy_resume();
- twl4030_usb_set_bits(twl, OTG_CTRL,
- OTG_CTRL_DMPULLDOWN | OTG_CTRL_DPPULLDOWN);
+ twl4030_usb_set_bits(twl, TWL4030_OTG_CTRL,
+ TWL4030_OTG_CTRL_DMPULLDOWN
+ | TWL4030_OTG_CTRL_DPPULLDOWN);
twl4030_usb_set_bits(twl, USB_INT_EN_RISE, USB_INT_IDGND);
twl4030_usb_set_bits(twl, USB_INT_EN_FALL, USB_INT_IDGND);
twl4030_usb_set_bits(twl, FUNC_CTRL, FUNC_CTRL_SUSPENDM);
- twl4030_usb_set_bits(twl, OTG_CTRL, OTG_CTRL_DRVVBUS);
+ twl4030_usb_set_bits(twl, TWL4030_OTG_CTRL, TWL4030_OTG_CTRL_DRVVBUS);
return 0;
}
diff --git a/drivers/usb/gadget/omap_udc.c b/drivers/usb/gadget/omap_udc.c
index 22aabd4..3528f49 100644
--- a/drivers/usb/gadget/omap_udc.c
+++ b/drivers/usb/gadget/omap_udc.c
@@ -136,13 +136,17 @@ static void use_ep(struct omap_ep *ep, u16 select)
if (ep->bEndpointAddress & USB_DIR_IN)
num |= UDC_EP_DIR;
- UDC_EP_NUM_REG = num | select;
+ omap_writew(num | select, UDC_EP_NUM);
/* when select, MUST deselect later !! */
}
static inline void deselect_ep(void)
{
- UDC_EP_NUM_REG &= ~UDC_EP_SEL;
+ u16 w;
+
+ w = omap_readw(UDC_EP_NUM);
+ w &= ~UDC_EP_SEL;
+ omap_writew(w, UDC_EP_NUM);
/* 6 wait states before TX will happen */
}
@@ -217,7 +221,7 @@ static int omap_ep_enable(struct usb_ep *_ep,
ep->has_dma = 0;
ep->lch = -1;
use_ep(ep, UDC_EP_SEL);
- UDC_CTRL_REG = udc->clr_halt;
+ omap_writew(udc->clr_halt, UDC_CTRL);
ep->ackwait = 0;
deselect_ep();
@@ -233,7 +237,7 @@ static int omap_ep_enable(struct usb_ep *_ep,
if (desc->bmAttributes != USB_ENDPOINT_XFER_ISOC
&& !ep->has_dma
&& !(ep->bEndpointAddress & USB_DIR_IN)) {
- UDC_CTRL_REG = UDC_SET_FIFO_EN;
+ omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
ep->ackwait = 1 + ep->double_buf;
}
@@ -260,7 +264,7 @@ static int omap_ep_disable(struct usb_ep *_ep)
nuke (ep, -ESHUTDOWN);
ep->ep.maxpacket = ep->maxpacket;
ep->has_dma = 0;
- UDC_CTRL_REG = UDC_SET_HALT;
+ omap_writew(UDC_SET_HALT, UDC_CTRL);
list_del_init(&ep->iso);
del_timer(&ep->timer);
@@ -361,13 +365,13 @@ write_packet(u8 *buf, struct omap_req *req, unsigned max)
if (likely((((int)buf) & 1) == 0)) {
wp = (u16 *)buf;
while (max >= 2) {
- UDC_DATA_REG = *wp++;
+ omap_writew(*wp++, UDC_DATA);
max -= 2;
}
buf = (u8 *)wp;
}
while (max--)
- *(volatile u8 *)&UDC_DATA_REG = *buf++;
+ omap_writeb(*buf++, UDC_DATA);
return len;
}
@@ -386,13 +390,13 @@ static int write_fifo(struct omap_ep *ep, struct omap_req *req)
prefetch(buf);
/* PIO-IN isn't double buffered except for iso */
- ep_stat = UDC_STAT_FLG_REG;
+ ep_stat = omap_readw(UDC_STAT_FLG);
if (ep_stat & UDC_FIFO_UNWRITABLE)
return 0;
count = ep->ep.maxpacket;
count = write_packet(buf, req, count);
- UDC_CTRL_REG = UDC_SET_FIFO_EN;
+ omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
ep->ackwait = 1;
/* last packet is often short (sometimes a zlp) */
@@ -426,13 +430,13 @@ read_packet(u8 *buf, struct omap_req *req, unsigned avail)
if (likely((((int)buf) & 1) == 0)) {
wp = (u16 *)buf;
while (avail >= 2) {
- *wp++ = UDC_DATA_REG;
+ *wp++ = omap_readw(UDC_DATA);
avail -= 2;
}
buf = (u8 *)wp;
}
while (avail--)
- *buf++ = *(volatile u8 *)&UDC_DATA_REG;
+ *buf++ = omap_readb(UDC_DATA);
return len;
}
@@ -447,7 +451,7 @@ static int read_fifo(struct omap_ep *ep, struct omap_req *req)
prefetchw(buf);
for (;;) {
- u16 ep_stat = UDC_STAT_FLG_REG;
+ u16 ep_stat = omap_readw(UDC_STAT_FLG);
is_last = 0;
if (ep_stat & FIFO_EMPTY) {
@@ -461,7 +465,7 @@ static int read_fifo(struct omap_ep *ep, struct omap_req *req)
if (ep_stat & UDC_FIFO_FULL)
avail = ep->ep.maxpacket;
else {
- avail = UDC_RXFSTAT_REG;
+ avail = omap_readw(UDC_RXFSTAT);
ep->fnf = ep->double_buf;
}
count = read_packet(buf, req, avail);
@@ -474,7 +478,7 @@ static int read_fifo(struct omap_ep *ep, struct omap_req *req)
req->req.status = -EOVERFLOW;
avail -= count;
while (avail--)
- (void) *(volatile u8 *)&UDC_DATA_REG;
+ omap_readw(UDC_DATA);
}
} else if (req->req.length == req->req.actual)
is_last = 1;
@@ -536,7 +540,7 @@ static u16 dma_dest_len(struct omap_ep *ep, dma_addr_t start)
static void next_in_dma(struct omap_ep *ep, struct omap_req *req)
{
- u16 txdma_ctrl;
+ u16 txdma_ctrl, w;
unsigned length = req->req.length - req->req.actual;
const int sync_mode = cpu_is_omap15xx()
? OMAP_DMA_SYNC_FRAME
@@ -568,13 +572,17 @@ static void next_in_dma(struct omap_ep *ep, struct omap_req *req)
omap_start_dma(ep->lch);
ep->dma_counter = omap_get_dma_src_pos(ep->lch);
- UDC_DMA_IRQ_EN_REG |= UDC_TX_DONE_IE(ep->dma_channel);
- UDC_TXDMA_REG(ep->dma_channel) = UDC_TXN_START | txdma_ctrl;
+ w = omap_readw(UDC_DMA_IRQ_EN);
+ w |= UDC_TX_DONE_IE(ep->dma_channel);
+ omap_writew(w, UDC_DMA_IRQ_EN);
+ omap_writew(UDC_TXN_START | txdma_ctrl, UDC_TXDMA(ep->dma_channel));
req->dma_bytes = length;
}
static void finish_in_dma(struct omap_ep *ep, struct omap_req *req, int status)
{
+ u16 w;
+
if (status == 0) {
req->req.actual += req->dma_bytes;
@@ -591,7 +599,9 @@ static void finish_in_dma(struct omap_ep *ep, struct omap_req *req, int status)
/* tx completion */
omap_stop_dma(ep->lch);
- UDC_DMA_IRQ_EN_REG &= ~UDC_TX_DONE_IE(ep->dma_channel);
+ w = omap_readw(UDC_DMA_IRQ_EN);
+ w &= ~UDC_TX_DONE_IE(ep->dma_channel);
+ omap_writew(w, UDC_DMA_IRQ_EN);
done(ep, req, status);
}
@@ -599,6 +609,7 @@ static void next_out_dma(struct omap_ep *ep, struct omap_req *req)
{
unsigned packets = req->req.length - req->req.actual;
int dma_trigger = 0;
+ u16 w;
if (cpu_is_omap24xx())
dma_trigger = OMAP24XX_DMA(USB_W2FC_RX0, ep->dma_channel);
@@ -627,10 +638,12 @@ static void next_out_dma(struct omap_ep *ep, struct omap_req *req)
0, 0);
ep->dma_counter = omap_get_dma_dst_pos(ep->lch);
- UDC_RXDMA_REG(ep->dma_channel) = UDC_RXN_STOP | (packets - 1);
- UDC_DMA_IRQ_EN_REG |= UDC_RX_EOT_IE(ep->dma_channel);
- UDC_EP_NUM_REG = (ep->bEndpointAddress & 0xf);
- UDC_CTRL_REG = UDC_SET_FIFO_EN;
+ omap_writew(UDC_RXN_STOP | (packets - 1), UDC_RXDMA(ep->dma_channel));
+ w = omap_readw(UDC_DMA_IRQ_EN);
+ w |= UDC_RX_EOT_IE(ep->dma_channel);
+ omap_writew(w, UDC_DMA_IRQ_EN);
+ omap_writew(ep->bEndpointAddress & 0xf, UDC_EP_NUM);
+ omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
omap_start_dma(ep->lch);
}
@@ -638,7 +651,7 @@ static void next_out_dma(struct omap_ep *ep, struct omap_req *req)
static void
finish_out_dma(struct omap_ep *ep, struct omap_req *req, int status, int one)
{
- u16 count;
+ u16 count, w;
if (status == 0)
ep->dma_counter = (u16) (req->req.dma + req->req.actual);
@@ -657,13 +670,15 @@ finish_out_dma(struct omap_ep *ep, struct omap_req *req, int status, int one)
return;
/* rx completion */
- UDC_DMA_IRQ_EN_REG &= ~UDC_RX_EOT_IE(ep->dma_channel);
+ w = omap_readw(UDC_DMA_IRQ_EN);
+ w &= ~UDC_RX_EOT_IE(ep->dma_channel);
+ omap_writew(w, UDC_DMA_IRQ_EN);
done(ep, req, status);
}
static void dma_irq(struct omap_udc *udc, u16 irq_src)
{
- u16 dman_stat = UDC_DMAN_STAT_REG;
+ u16 dman_stat = omap_readw(UDC_DMAN_STAT);
struct omap_ep *ep;
struct omap_req *req;
@@ -677,7 +692,7 @@ static void dma_irq(struct omap_udc *udc, u16 irq_src)
struct omap_req, queue);
finish_in_dma(ep, req, 0);
}
- UDC_IRQ_SRC_REG = UDC_TXN_DONE;
+ omap_writew(UDC_TXN_DONE, UDC_IRQ_SRC);
if (!list_empty (&ep->queue)) {
req = container_of(ep->queue.next,
@@ -696,7 +711,7 @@ static void dma_irq(struct omap_udc *udc, u16 irq_src)
struct omap_req, queue);
finish_out_dma(ep, req, 0, dman_stat & UDC_DMA_RX_SB);
}
- UDC_IRQ_SRC_REG = UDC_RXN_EOT;
+ omap_writew(UDC_RXN_EOT, UDC_IRQ_SRC);
if (!list_empty (&ep->queue)) {
req = container_of(ep->queue.next,
@@ -710,7 +725,7 @@ static void dma_irq(struct omap_udc *udc, u16 irq_src)
ep->irqs++;
/* omap15xx does this unasked... */
VDBG("%s, RX_CNT irq?\n", ep->ep.name);
- UDC_IRQ_SRC_REG = UDC_RXN_CNT;
+ omap_writew(UDC_RXN_CNT, UDC_IRQ_SRC);
}
}
@@ -733,9 +748,9 @@ static void dma_channel_claim(struct omap_ep *ep, unsigned channel)
is_in = ep->bEndpointAddress & USB_DIR_IN;
if (is_in)
- reg = UDC_TXDMA_CFG_REG;
+ reg = omap_readw(UDC_TXDMA_CFG);
else
- reg = UDC_RXDMA_CFG_REG;
+ reg = omap_readw(UDC_RXDMA_CFG);
reg |= UDC_DMA_REQ; /* "pulse" activated */
ep->dma_channel = 0;
@@ -763,7 +778,7 @@ static void dma_channel_claim(struct omap_ep *ep, unsigned channel)
status = omap_request_dma(dma_channel,
ep->ep.name, dma_error, ep, &ep->lch);
if (status == 0) {
- UDC_TXDMA_CFG_REG = reg;
+ omap_writew(reg, UDC_TXDMA_CFG);
/* EMIFF or SDRC */
omap_set_dma_src_burst_mode(ep->lch,
OMAP_DMA_DATA_BURST_4);
@@ -772,7 +787,7 @@ static void dma_channel_claim(struct omap_ep *ep, unsigned channel)
omap_set_dma_dest_params(ep->lch,
OMAP_DMA_PORT_TIPB,
OMAP_DMA_AMODE_CONSTANT,
- (unsigned long) io_v2p((u32)&UDC_DATA_DMA_REG),
+ (unsigned long) io_v2p(UDC_DATA_DMA),
0, 0);
}
} else {
@@ -784,12 +799,12 @@ static void dma_channel_claim(struct omap_ep *ep, unsigned channel)
status = omap_request_dma(dma_channel,
ep->ep.name, dma_error, ep, &ep->lch);
if (status == 0) {
- UDC_RXDMA_CFG_REG = reg;
+ omap_writew(reg, UDC_RXDMA_CFG);
/* TIPB */
omap_set_dma_src_params(ep->lch,
OMAP_DMA_PORT_TIPB,
OMAP_DMA_AMODE_CONSTANT,
- (unsigned long) io_v2p((u32)&UDC_DATA_DMA_REG),
+ (unsigned long) io_v2p(UDC_DATA_DMA),
0, 0);
/* EMIFF or SDRC */
omap_set_dma_dest_burst_mode(ep->lch,
@@ -831,7 +846,7 @@ just_restart:
(is_in ? write_fifo : read_fifo)(ep, req);
deselect_ep();
if (!is_in) {
- UDC_CTRL_REG = UDC_SET_FIFO_EN;
+ omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
ep->ackwait = 1 + ep->double_buf;
}
/* IN: 6 wait states before it'll tx */
@@ -865,23 +880,25 @@ static void dma_channel_release(struct omap_ep *ep)
/* wait till current packet DMA finishes, and fifo empties */
if (ep->bEndpointAddress & USB_DIR_IN) {
- UDC_TXDMA_CFG_REG = (UDC_TXDMA_CFG_REG & ~mask) | UDC_DMA_REQ;
+ omap_writew((omap_readw(UDC_TXDMA_CFG) & ~mask) | UDC_DMA_REQ,
+ UDC_TXDMA_CFG);
if (req) {
finish_in_dma(ep, req, -ECONNRESET);
/* clear FIFO; hosts probably won't empty it */
use_ep(ep, UDC_EP_SEL);
- UDC_CTRL_REG = UDC_CLR_EP;
+ omap_writew(UDC_CLR_EP, UDC_CTRL);
deselect_ep();
}
- while (UDC_TXDMA_CFG_REG & mask)
+ while (omap_readw(UDC_TXDMA_CFG) & mask)
udelay(10);
} else {
- UDC_RXDMA_CFG_REG = (UDC_RXDMA_CFG_REG & ~mask) | UDC_DMA_REQ;
+ omap_writew((omap_readw(UDC_RXDMA_CFG) & ~mask) | UDC_DMA_REQ,
+ UDC_RXDMA_CFG);
/* dma empties the fifo */
- while (UDC_RXDMA_CFG_REG & mask)
+ while (omap_readw(UDC_RXDMA_CFG) & mask)
udelay(10);
if (req)
finish_out_dma(ep, req, -ECONNRESET, 0);
@@ -968,9 +985,13 @@ omap_ep_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags)
req->req.actual = 0;
/* maybe kickstart non-iso i/o queues */
- if (is_iso)
- UDC_IRQ_EN_REG |= UDC_SOF_IE;
- else if (list_empty(&ep->queue) && !ep->stopped && !ep->ackwait) {
+ if (is_iso) {
+ u16 w;
+
+ w = omap_readw(UDC_IRQ_EN);
+ w |= UDC_SOF_IE;
+ omap_writew(w, UDC_IRQ_EN);
+ } else if (list_empty(&ep->queue) && !ep->stopped && !ep->ackwait) {
int is_in;
if (ep->bEndpointAddress == 0) {
@@ -988,23 +1009,23 @@ omap_ep_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags)
* requests to non-control endpoints
*/
if (udc->ep0_set_config) {
- u16 irq_en = UDC_IRQ_EN_REG;
+ u16 irq_en = omap_readw(UDC_IRQ_EN);
irq_en |= UDC_DS_CHG_IE | UDC_EP0_IE;
if (!udc->ep0_reset_config)
irq_en |= UDC_EPN_RX_IE
| UDC_EPN_TX_IE;
- UDC_IRQ_EN_REG = irq_en;
+ omap_writew(irq_en, UDC_IRQ_EN);
}
/* STATUS for zero length DATA stages is
* always an IN ... even for IN transfers,
* a weird case which seem to stall OMAP.
*/
- UDC_EP_NUM_REG = (UDC_EP_SEL|UDC_EP_DIR);
- UDC_CTRL_REG = UDC_CLR_EP;
- UDC_CTRL_REG = UDC_SET_FIFO_EN;
- UDC_EP_NUM_REG = UDC_EP_DIR;
+ omap_writew(UDC_EP_SEL | UDC_EP_DIR, UDC_EP_NUM);
+ omap_writew(UDC_CLR_EP, UDC_CTRL);
+ omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
+ omap_writew(UDC_EP_DIR, UDC_EP_NUM);
/* cleanup */
udc->ep0_pending = 0;
@@ -1013,11 +1034,11 @@ omap_ep_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags)
/* non-empty DATA stage */
} else if (is_in) {
- UDC_EP_NUM_REG = UDC_EP_SEL|UDC_EP_DIR;
+ omap_writew(UDC_EP_SEL | UDC_EP_DIR, UDC_EP_NUM);
} else {
if (udc->ep0_setup)
goto irq_wait;
- UDC_EP_NUM_REG = UDC_EP_SEL;
+ omap_writew(UDC_EP_SEL, UDC_EP_NUM);
}
} else {
is_in = ep->bEndpointAddress & USB_DIR_IN;
@@ -1033,7 +1054,7 @@ omap_ep_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags)
req = NULL;
deselect_ep();
if (!is_in) {
- UDC_CTRL_REG = UDC_SET_FIFO_EN;
+ omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
ep->ackwait = 1 + ep->double_buf;
}
/* IN: 6 wait states before it'll tx */
@@ -1101,9 +1122,9 @@ static int omap_ep_set_halt(struct usb_ep *_ep, int value)
else if (value) {
if (ep->udc->ep0_set_config) {
WARN("error changing config?\n");
- UDC_SYSCON2_REG = UDC_CLR_CFG;
+ omap_writew(UDC_CLR_CFG, UDC_SYSCON2);
}
- UDC_SYSCON2_REG = UDC_STALL_CMD;
+ omap_writew(UDC_STALL_CMD, UDC_SYSCON2);
ep->udc->ep0_pending = 0;
status = 0;
} else /* NOP */
@@ -1130,8 +1151,8 @@ static int omap_ep_set_halt(struct usb_ep *_ep, int value)
channel = 0;
use_ep(ep, UDC_EP_SEL);
- if (UDC_STAT_FLG_REG & UDC_NON_ISO_FIFO_EMPTY) {
- UDC_CTRL_REG = UDC_SET_HALT;
+ if (omap_readw(UDC_STAT_FLG) & UDC_NON_ISO_FIFO_EMPTY) {
+ omap_writew(UDC_SET_HALT, UDC_CTRL);
status = 0;
} else
status = -EAGAIN;
@@ -1141,10 +1162,10 @@ static int omap_ep_set_halt(struct usb_ep *_ep, int value)
dma_channel_claim(ep, channel);
} else {
use_ep(ep, 0);
- UDC_CTRL_REG = ep->udc->clr_halt;
+ omap_writew(ep->udc->clr_halt, UDC_CTRL);
ep->ackwait = 0;
if (!(ep->bEndpointAddress & USB_DIR_IN)) {
- UDC_CTRL_REG = UDC_SET_FIFO_EN;
+ omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
ep->ackwait = 1 + ep->double_buf;
}
}
@@ -1176,7 +1197,7 @@ static struct usb_ep_ops omap_ep_ops = {
static int omap_get_frame(struct usb_gadget *gadget)
{
- u16 sof = UDC_SOF_REG;
+ u16 sof = omap_readw(UDC_SOF);
return (sof & UDC_TS_OK) ? (sof & UDC_TS) : -EL2NSYNC;
}
@@ -1195,7 +1216,7 @@ static int omap_wakeup(struct usb_gadget *gadget)
*/
if (udc->devstat & (UDC_B_HNP_ENABLE|UDC_R_WK_OK)) {
DBG("remote wakeup...\n");
- UDC_SYSCON2_REG = UDC_RMT_WKP;
+ omap_writew(UDC_RMT_WKP, UDC_SYSCON2);
retval = 0;
}
@@ -1218,12 +1239,12 @@ omap_set_selfpowered(struct usb_gadget *gadget, int is_selfpowered)
udc = container_of(gadget, struct omap_udc, gadget);
spin_lock_irqsave(&udc->lock, flags);
- syscon1 = UDC_SYSCON1_REG;
+ syscon1 = omap_readw(UDC_SYSCON1);
if (is_selfpowered)
syscon1 |= UDC_SELF_PWR;
else
syscon1 &= ~UDC_SELF_PWR;
- UDC_SYSCON1_REG = syscon1;
+ omap_writew(syscon1, UDC_SYSCON1);
spin_unlock_irqrestore(&udc->lock, flags);
return 0;
@@ -1236,18 +1257,36 @@ static int can_pullup(struct omap_udc *udc)
static void pullup_enable(struct omap_udc *udc)
{
- UDC_SYSCON1_REG |= UDC_PULLUP_EN;
- if (!gadget_is_otg(&udc->gadget) && !cpu_is_omap15xx())
- OTG_CTRL_REG |= OTG_BSESSVLD;
- UDC_IRQ_EN_REG = UDC_DS_CHG_IE;
+ u16 w;
+
+ w = omap_readw(UDC_SYSCON1);
+ w |= UDC_PULLUP_EN;
+ omap_writew(w, UDC_SYSCON1);
+ if (!gadget_is_otg(&udc->gadget) && !cpu_is_omap15xx()) {
+ u32 l;
+
+ l = omap_readl(OTG_CTRL);
+ l |= OTG_BSESSVLD;
+ omap_writel(l, OTG_CTRL);
+ }
+ omap_writew(UDC_DS_CHG_IE, UDC_IRQ_EN);
}
static void pullup_disable(struct omap_udc *udc)
{
- if (!gadget_is_otg(&udc->gadget) && !cpu_is_omap15xx())
- OTG_CTRL_REG &= ~OTG_BSESSVLD;
- UDC_IRQ_EN_REG = UDC_DS_CHG_IE;
- UDC_SYSCON1_REG &= ~UDC_PULLUP_EN;
+ u16 w;
+
+ if (!gadget_is_otg(&udc->gadget) && !cpu_is_omap15xx()) {
+ u32 l;
+
+ l = omap_readl(OTG_CTRL);
+ l &= ~OTG_BSESSVLD;
+ omap_writel(l, OTG_CTRL);
+ }
+ omap_writew(UDC_DS_CHG_IE, UDC_IRQ_EN);
+ w = omap_readw(UDC_SYSCON1);
+ w &= ~UDC_PULLUP_EN;
+ omap_writew(w, UDC_SYSCON1);
}
static struct omap_udc *udc;
@@ -1275,6 +1314,7 @@ static int omap_vbus_session(struct usb_gadget *gadget, int is_active)
{
struct omap_udc *udc;
unsigned long flags;
+ u32 l;
udc = container_of(gadget, struct omap_udc, gadget);
spin_lock_irqsave(&udc->lock, flags);
@@ -1282,10 +1322,12 @@ static int omap_vbus_session(struct usb_gadget *gadget, int is_active)
udc->vbus_active = (is_active != 0);
if (cpu_is_omap15xx()) {
/* "software" detect, ignored if !VBUS_MODE_1510 */
+ l = omap_readl(FUNC_MUX_CTRL_0);
if (is_active)
- FUNC_MUX_CTRL_0_REG |= VBUS_CTRL_1510;
+ l |= VBUS_CTRL_1510;
else
- FUNC_MUX_CTRL_0_REG &= ~VBUS_CTRL_1510;
+ l &= ~VBUS_CTRL_1510;
+ omap_writel(l, FUNC_MUX_CTRL_0);
}
if (udc->dc_clk != NULL && is_active) {
if (!udc->clk_requested) {
@@ -1355,9 +1397,9 @@ static void nuke(struct omap_ep *ep, int status)
dma_channel_release(ep);
use_ep(ep, 0);
- UDC_CTRL_REG = UDC_CLR_EP;
+ omap_writew(UDC_CLR_EP, UDC_CTRL);
if (ep->bEndpointAddress && ep->bmAttributes != USB_ENDPOINT_XFER_ISOC)
- UDC_CTRL_REG = UDC_SET_HALT;
+ omap_writew(UDC_SET_HALT, UDC_CTRL);
while (!list_empty(&ep->queue)) {
req = list_entry(ep->queue.next, struct omap_req, queue);
@@ -1385,8 +1427,8 @@ static void update_otg(struct omap_udc *udc)
if (!gadget_is_otg(&udc->gadget))
return;
- if (OTG_CTRL_REG & OTG_ID)
- devstat = UDC_DEVSTAT_REG;
+ if (omap_readl(OTG_CTRL) & OTG_ID)
+ devstat = omap_readw(UDC_DEVSTAT);
else
devstat = 0;
@@ -1397,9 +1439,14 @@ static void update_otg(struct omap_udc *udc)
/* Enable HNP early, avoiding races on suspend irq path.
* ASSUMES OTG state machine B_BUS_REQ input is true.
*/
- if (udc->gadget.b_hnp_enable)
- OTG_CTRL_REG = (OTG_CTRL_REG | OTG_B_HNPEN | OTG_B_BUSREQ)
- & ~OTG_PULLUP;
+ if (udc->gadget.b_hnp_enable) {
+ u32 l;
+
+ l = omap_readl(OTG_CTRL);
+ l |= OTG_B_HNPEN | OTG_B_BUSREQ;
+ l &= ~OTG_PULLUP;
+ omap_writel(l, OTG_CTRL);
+ }
}
static void ep0_irq(struct omap_udc *udc, u16 irq_src)
@@ -1417,7 +1464,7 @@ static void ep0_irq(struct omap_udc *udc, u16 irq_src)
nuke(ep0, 0);
if (ack) {
- UDC_IRQ_SRC_REG = ack;
+ omap_writew(ack, UDC_IRQ_SRC);
irq_src = UDC_SETUP;
}
}
@@ -1437,9 +1484,9 @@ static void ep0_irq(struct omap_udc *udc, u16 irq_src)
if (irq_src & UDC_EP0_TX) {
int stat;
- UDC_IRQ_SRC_REG = UDC_EP0_TX;
- UDC_EP_NUM_REG = UDC_EP_SEL|UDC_EP_DIR;
- stat = UDC_STAT_FLG_REG;
+ omap_writew(UDC_EP0_TX, UDC_IRQ_SRC);
+ omap_writew(UDC_EP_SEL|UDC_EP_DIR, UDC_EP_NUM);
+ stat = omap_readw(UDC_STAT_FLG);
if (stat & UDC_ACK) {
if (udc->ep0_in) {
/* write next IN packet from response,
@@ -1447,26 +1494,26 @@ static void ep0_irq(struct omap_udc *udc, u16 irq_src)
*/
if (req)
stat = write_fifo(ep0, req);
- UDC_EP_NUM_REG = UDC_EP_DIR;
+ omap_writew(UDC_EP_DIR, UDC_EP_NUM);
if (!req && udc->ep0_pending) {
- UDC_EP_NUM_REG = UDC_EP_SEL;
- UDC_CTRL_REG = UDC_CLR_EP;
- UDC_CTRL_REG = UDC_SET_FIFO_EN;
- UDC_EP_NUM_REG = 0;
+ omap_writew(UDC_EP_SEL, UDC_EP_NUM);
+ omap_writew(UDC_CLR_EP, UDC_CTRL);
+ omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
+ omap_writew(0, UDC_EP_NUM);
udc->ep0_pending = 0;
} /* else: 6 wait states before it'll tx */
} else {
/* ack status stage of OUT transfer */
- UDC_EP_NUM_REG = UDC_EP_DIR;
+ omap_writew(UDC_EP_DIR, UDC_EP_NUM);
if (req)
done(ep0, req, 0);
}
req = NULL;
} else if (stat & UDC_STALL) {
- UDC_CTRL_REG = UDC_CLR_HALT;
- UDC_EP_NUM_REG = UDC_EP_DIR;
+ omap_writew(UDC_CLR_HALT, UDC_CTRL);
+ omap_writew(UDC_EP_DIR, UDC_EP_NUM);
} else {
- UDC_EP_NUM_REG = UDC_EP_DIR;
+ omap_writew(UDC_EP_DIR, UDC_EP_NUM);
}
}
@@ -1474,9 +1521,9 @@ static void ep0_irq(struct omap_udc *udc, u16 irq_src)
if (irq_src & UDC_EP0_RX) {
int stat;
- UDC_IRQ_SRC_REG = UDC_EP0_RX;
- UDC_EP_NUM_REG = UDC_EP_SEL;
- stat = UDC_STAT_FLG_REG;
+ omap_writew(UDC_EP0_RX, UDC_IRQ_SRC);
+ omap_writew(UDC_EP_SEL, UDC_EP_NUM);
+ stat = omap_readw(UDC_STAT_FLG);
if (stat & UDC_ACK) {
if (!udc->ep0_in) {
stat = 0;
@@ -1484,34 +1531,35 @@ static void ep0_irq(struct omap_udc *udc, u16 irq_src)
* reactiviting the fifo; stall on errors.
*/
if (!req || (stat = read_fifo(ep0, req)) < 0) {
- UDC_SYSCON2_REG = UDC_STALL_CMD;
+ omap_writew(UDC_STALL_CMD, UDC_SYSCON2);
udc->ep0_pending = 0;
stat = 0;
} else if (stat == 0)
- UDC_CTRL_REG = UDC_SET_FIFO_EN;
- UDC_EP_NUM_REG = 0;
+ omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
+ omap_writew(0, UDC_EP_NUM);
/* activate status stage */
if (stat == 1) {
done(ep0, req, 0);
/* that may have STALLed ep0... */
- UDC_EP_NUM_REG = UDC_EP_SEL|UDC_EP_DIR;
- UDC_CTRL_REG = UDC_CLR_EP;
- UDC_CTRL_REG = UDC_SET_FIFO_EN;
- UDC_EP_NUM_REG = UDC_EP_DIR;
+ omap_writew(UDC_EP_SEL | UDC_EP_DIR,
+ UDC_EP_NUM);
+ omap_writew(UDC_CLR_EP, UDC_CTRL);
+ omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
+ omap_writew(UDC_EP_DIR, UDC_EP_NUM);
udc->ep0_pending = 0;
}
} else {
/* ack status stage of IN transfer */
- UDC_EP_NUM_REG = 0;
+ omap_writew(0, UDC_EP_NUM);
if (req)
done(ep0, req, 0);
}
} else if (stat & UDC_STALL) {
- UDC_CTRL_REG = UDC_CLR_HALT;
- UDC_EP_NUM_REG = 0;
+ omap_writew(UDC_CLR_HALT, UDC_CTRL);
+ omap_writew(0, UDC_EP_NUM);
} else {
- UDC_EP_NUM_REG = 0;
+ omap_writew(0, UDC_EP_NUM);
}
}
@@ -1526,14 +1574,14 @@ static void ep0_irq(struct omap_udc *udc, u16 irq_src)
/* read the (latest) SETUP message */
do {
- UDC_EP_NUM_REG = UDC_SETUP_SEL;
+ omap_writew(UDC_SETUP_SEL, UDC_EP_NUM);
/* two bytes at a time */
- u.word[0] = UDC_DATA_REG;
- u.word[1] = UDC_DATA_REG;
- u.word[2] = UDC_DATA_REG;
- u.word[3] = UDC_DATA_REG;
- UDC_EP_NUM_REG = 0;
- } while (UDC_IRQ_SRC_REG & UDC_SETUP);
+ u.word[0] = omap_readw(UDC_DATA);
+ u.word[1] = omap_readw(UDC_DATA);
+ u.word[2] = omap_readw(UDC_DATA);
+ u.word[3] = omap_readw(UDC_DATA);
+ omap_writew(0, UDC_EP_NUM);
+ } while (omap_readw(UDC_IRQ_SRC) & UDC_SETUP);
#define w_value le16_to_cpu(u.r.wValue)
#define w_index le16_to_cpu(u.r.wIndex)
@@ -1564,9 +1612,9 @@ static void ep0_irq(struct omap_udc *udc, u16 irq_src)
* later if it fails the request.
*/
if (udc->ep0_reset_config)
- UDC_SYSCON2_REG = UDC_CLR_CFG;
+ omap_writew(UDC_CLR_CFG, UDC_SYSCON2);
else
- UDC_SYSCON2_REG = UDC_DEV_CFG;
+ omap_writew(UDC_DEV_CFG, UDC_SYSCON2);
update_otg(udc);
goto delegate;
case USB_REQ_CLEAR_FEATURE:
@@ -1584,10 +1632,10 @@ static void ep0_irq(struct omap_udc *udc, u16 irq_src)
|| !ep->desc)
goto do_stall;
use_ep(ep, 0);
- UDC_CTRL_REG = udc->clr_halt;
+ omap_writew(udc->clr_halt, UDC_CTRL);
ep->ackwait = 0;
if (!(ep->bEndpointAddress & USB_DIR_IN)) {
- UDC_CTRL_REG = UDC_SET_FIFO_EN;
+ omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
ep->ackwait = 1 + ep->double_buf;
}
/* NOTE: assumes the host behaves sanely,
@@ -1620,15 +1668,15 @@ static void ep0_irq(struct omap_udc *udc, u16 irq_src)
}
use_ep(ep, 0);
/* can't halt if fifo isn't empty... */
- UDC_CTRL_REG = UDC_CLR_EP;
- UDC_CTRL_REG = UDC_SET_HALT;
+ omap_writew(UDC_CLR_EP, UDC_CTRL);
+ omap_writew(UDC_SET_HALT, UDC_CTRL);
VDBG("%s halted by host\n", ep->name);
ep0out_status_stage:
status = 0;
- UDC_EP_NUM_REG = UDC_EP_SEL|UDC_EP_DIR;
- UDC_CTRL_REG = UDC_CLR_EP;
- UDC_CTRL_REG = UDC_SET_FIFO_EN;
- UDC_EP_NUM_REG = UDC_EP_DIR;
+ omap_writew(UDC_EP_SEL|UDC_EP_DIR, UDC_EP_NUM);
+ omap_writew(UDC_CLR_EP, UDC_CTRL);
+ omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
+ omap_writew(UDC_EP_DIR, UDC_EP_NUM);
udc->ep0_pending = 0;
break;
case USB_REQ_GET_STATUS:
@@ -1665,10 +1713,10 @@ intf_status:
zero_status:
/* return two zero bytes */
- UDC_EP_NUM_REG = UDC_EP_SEL|UDC_EP_DIR;
- UDC_DATA_REG = 0;
- UDC_CTRL_REG = UDC_SET_FIFO_EN;
- UDC_EP_NUM_REG = UDC_EP_DIR;
+ omap_writew(UDC_EP_SEL|UDC_EP_DIR, UDC_EP_NUM);
+ omap_writew(0, UDC_DATA);
+ omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
+ omap_writew(UDC_EP_DIR, UDC_EP_NUM);
status = 0;
VDBG("GET_STATUS, interface %d\n", w_index);
/* next, status stage */
@@ -1677,8 +1725,8 @@ zero_status:
delegate:
/* activate the ep0out fifo right away */
if (!udc->ep0_in && w_length) {
- UDC_EP_NUM_REG = 0;
- UDC_CTRL_REG = UDC_SET_FIFO_EN;
+ omap_writew(0, UDC_EP_NUM);
+ omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
}
/* gadget drivers see class/vendor specific requests,
@@ -1719,9 +1767,9 @@ do_stall:
if (udc->ep0_reset_config)
WARN("error resetting config?\n");
else
- UDC_SYSCON2_REG = UDC_CLR_CFG;
+ omap_writew(UDC_CLR_CFG, UDC_SYSCON2);
}
- UDC_SYSCON2_REG = UDC_STALL_CMD;
+ omap_writew(UDC_STALL_CMD, UDC_SYSCON2);
udc->ep0_pending = 0;
}
}
@@ -1735,7 +1783,7 @@ static void devstate_irq(struct omap_udc *udc, u16 irq_src)
{
u16 devstat, change;
- devstat = UDC_DEVSTAT_REG;
+ devstat = omap_readw(UDC_DEVSTAT);
change = devstat ^ udc->devstat;
udc->devstat = devstat;
@@ -1775,7 +1823,8 @@ static void devstate_irq(struct omap_udc *udc, u16 irq_src)
INFO("USB reset done, gadget %s\n",
udc->driver->driver.name);
/* ep0 traffic is legal from now on */
- UDC_IRQ_EN_REG = UDC_DS_CHG_IE | UDC_EP0_IE;
+ omap_writew(UDC_DS_CHG_IE | UDC_EP0_IE,
+ UDC_IRQ_EN);
}
change &= ~UDC_USB_RESET;
}
@@ -1819,7 +1868,7 @@ static void devstate_irq(struct omap_udc *udc, u16 irq_src)
VDBG("devstat %03x, ignore change %03x\n",
devstat, change);
- UDC_IRQ_SRC_REG = UDC_DS_CHG;
+ omap_writew(UDC_DS_CHG, UDC_IRQ_SRC);
}
static irqreturn_t omap_udc_irq(int irq, void *_udc)
@@ -1830,7 +1879,7 @@ static irqreturn_t omap_udc_irq(int irq, void *_udc)
unsigned long flags;
spin_lock_irqsave(&udc->lock, flags);
- irq_src = UDC_IRQ_SRC_REG;
+ irq_src = omap_readw(UDC_IRQ_SRC);
/* Device state change (usb ch9 stuff) */
if (irq_src & UDC_DS_CHG) {
@@ -1853,7 +1902,7 @@ static irqreturn_t omap_udc_irq(int irq, void *_udc)
irq_src &= ~(UDC_TXN_DONE|UDC_RXN_CNT|UDC_RXN_EOT);
}
- irq_src &= ~(UDC_SOF|UDC_EPN_TX|UDC_EPN_RX);
+ irq_src &= ~(UDC_IRQ_SOF | UDC_EPN_TX|UDC_EPN_RX);
if (irq_src)
DBG("udc_irq, unhandled %03x\n", irq_src);
spin_unlock_irqrestore(&udc->lock, flags);
@@ -1874,7 +1923,7 @@ static void pio_out_timer(unsigned long _ep)
spin_lock_irqsave(&ep->udc->lock, flags);
if (!list_empty(&ep->queue) && ep->ackwait) {
use_ep(ep, UDC_EP_SEL);
- stat_flg = UDC_STAT_FLG_REG;
+ stat_flg = omap_readw(UDC_STAT_FLG);
if ((stat_flg & UDC_ACK) && (!(stat_flg & UDC_FIFO_EN)
|| (ep->double_buf && HALF_FULL(stat_flg)))) {
@@ -1884,8 +1933,8 @@ static void pio_out_timer(unsigned long _ep)
req = container_of(ep->queue.next,
struct omap_req, queue);
(void) read_fifo(ep, req);
- UDC_EP_NUM_REG = ep->bEndpointAddress;
- UDC_CTRL_REG = UDC_SET_FIFO_EN;
+ omap_writew(ep->bEndpointAddress, UDC_EP_NUM);
+ omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
ep->ackwait = 1 + ep->double_buf;
} else
deselect_ep();
@@ -1905,20 +1954,20 @@ static irqreturn_t omap_udc_pio_irq(int irq, void *_dev)
unsigned long flags;
spin_lock_irqsave(&udc->lock, flags);
- epn_stat = UDC_EPN_STAT_REG;
- irq_src = UDC_IRQ_SRC_REG;
+ epn_stat = omap_readw(UDC_EPN_STAT);
+ irq_src = omap_readw(UDC_IRQ_SRC);
/* handle OUT first, to avoid some wasteful NAKs */
if (irq_src & UDC_EPN_RX) {
epnum = (epn_stat >> 8) & 0x0f;
- UDC_IRQ_SRC_REG = UDC_EPN_RX;
+ omap_writew(UDC_EPN_RX, UDC_IRQ_SRC);
status = IRQ_HANDLED;
ep = &udc->ep[epnum];
ep->irqs++;
- UDC_EP_NUM_REG = epnum | UDC_EP_SEL;
+ omap_writew(epnum | UDC_EP_SEL, UDC_EP_NUM);
ep->fnf = 0;
- if ((UDC_STAT_FLG_REG & UDC_ACK)) {
+ if (omap_readw(UDC_STAT_FLG) & UDC_ACK) {
ep->ackwait--;
if (!list_empty(&ep->queue)) {
int stat;
@@ -1930,15 +1979,15 @@ static irqreturn_t omap_udc_pio_irq(int irq, void *_dev)
}
}
/* min 6 clock delay before clearing EP_SEL ... */
- epn_stat = UDC_EPN_STAT_REG;
- epn_stat = UDC_EPN_STAT_REG;
- UDC_EP_NUM_REG = epnum;
+ epn_stat = omap_readw(UDC_EPN_STAT);
+ epn_stat = omap_readw(UDC_EPN_STAT);
+ omap_writew(epnum, UDC_EP_NUM);
/* enabling fifo _after_ clearing ACK, contrary to docs,
* reduces lossage; timer still needed though (sigh).
*/
if (ep->fnf) {
- UDC_CTRL_REG = UDC_SET_FIFO_EN;
+ omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
ep->ackwait = 1 + ep->double_buf;
}
mod_timer(&ep->timer, PIO_OUT_TIMEOUT);
@@ -1947,13 +1996,13 @@ static irqreturn_t omap_udc_pio_irq(int irq, void *_dev)
/* then IN transfers */
else if (irq_src & UDC_EPN_TX) {
epnum = epn_stat & 0x0f;
- UDC_IRQ_SRC_REG = UDC_EPN_TX;
+ omap_writew(UDC_EPN_TX, UDC_IRQ_SRC);
status = IRQ_HANDLED;
ep = &udc->ep[16 + epnum];
ep->irqs++;
- UDC_EP_NUM_REG = epnum | UDC_EP_DIR | UDC_EP_SEL;
- if ((UDC_STAT_FLG_REG & UDC_ACK)) {
+ omap_writew(epnum | UDC_EP_DIR | UDC_EP_SEL, UDC_EP_NUM);
+ if (omap_readw(UDC_STAT_FLG) & UDC_ACK) {
ep->ackwait = 0;
if (!list_empty(&ep->queue)) {
req = container_of(ep->queue.next,
@@ -1962,9 +2011,9 @@ static irqreturn_t omap_udc_pio_irq(int irq, void *_dev)
}
}
/* min 6 clock delay before clearing EP_SEL ... */
- epn_stat = UDC_EPN_STAT_REG;
- epn_stat = UDC_EPN_STAT_REG;
- UDC_EP_NUM_REG = epnum | UDC_EP_DIR;
+ epn_stat = omap_readw(UDC_EPN_STAT);
+ epn_stat = omap_readw(UDC_EPN_STAT);
+ omap_writew(epnum | UDC_EP_DIR, UDC_EP_NUM);
/* then 6 clocks before it'd tx */
}
@@ -1992,7 +2041,7 @@ static irqreturn_t omap_udc_iso_irq(int irq, void *_dev)
req = list_entry(ep->queue.next, struct omap_req, queue);
use_ep(ep, UDC_EP_SEL);
- stat = UDC_STAT_FLG_REG;
+ stat = omap_readw(UDC_STAT_FLG);
/* NOTE: like the other controller drivers, this isn't
* currently reporting lost or damaged frames.
@@ -2024,9 +2073,14 @@ static irqreturn_t omap_udc_iso_irq(int irq, void *_dev)
if (!list_empty(&ep->queue))
pending = 1;
}
- if (!pending)
- UDC_IRQ_EN_REG &= ~UDC_SOF_IE;
- UDC_IRQ_SRC_REG = UDC_SOF;
+ if (!pending) {
+ u16 w;
+
+ w = omap_readw(UDC_IRQ_EN);
+ w &= ~UDC_SOF_IE;
+ omap_writew(w, UDC_IRQ_EN);
+ }
+ omap_writew(UDC_IRQ_SOF, UDC_IRQ_SRC);
spin_unlock_irqrestore(&udc->lock, flags);
return IRQ_HANDLED;
@@ -2075,7 +2129,7 @@ int usb_gadget_register_driver (struct usb_gadget_driver *driver)
if (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC)
continue;
use_ep(ep, 0);
- UDC_CTRL_REG = UDC_SET_HALT;
+ omap_writew(UDC_SET_HALT, UDC_CTRL);
}
udc->ep0_pending = 0;
udc->ep[0].irqs = 0;
@@ -2099,7 +2153,7 @@ int usb_gadget_register_driver (struct usb_gadget_driver *driver)
}
DBG("bound to driver %s\n", driver->driver.name);
- UDC_IRQ_SRC_REG = UDC_IRQ_SRC_MASK;
+ omap_writew(UDC_IRQ_SRC_MASK, UDC_IRQ_SRC);
/* connect to bus through transceiver */
if (udc->transceiver) {
@@ -2196,7 +2250,7 @@ static void proc_ep_show(struct seq_file *s, struct omap_ep *ep)
else
buf[0] = 0;
- stat_flg = UDC_STAT_FLG_REG;
+ stat_flg = omap_readw(UDC_STAT_FLG);
seq_printf(s,
"\n%s %s%s%sirqs %ld stat %04x " EIGHTBITS FOURBITS "%s\n",
ep->name, buf,
@@ -2257,12 +2311,12 @@ static int proc_otg_show(struct seq_file *s)
u32 trans;
char *ctrl_name;
- tmp = OTG_REV_REG;
+ tmp = omap_readw(OTG_REV);
if (cpu_is_omap24xx()) {
/*
* REVISIT: Not clear how this works on OMAP2. trans
* is ANDed to produce bits 7 and 8, which might make
- * sense for USB_TRANSCEIVER_CTRL_REG on OMAP1,
+ * sense for USB_TRANSCEIVER_CTRL on OMAP1,
* but with CONTROL_DEVCONF, these bits have something to
* do with the frame adjustment counter and McBSP2.
*/
@@ -2270,11 +2324,11 @@ static int proc_otg_show(struct seq_file *s)
trans = omap_ctrl_readb(OMAP2_CONTROL_DEVCONF0);
} else {
ctrl_name = "tranceiver_ctrl";
- trans = USB_TRANSCEIVER_CTRL_REG;
+ trans = omap_readw(USB_TRANSCEIVER_CTRL);
}
seq_printf(s, "\nOTG rev %d.%d, %s %05x\n",
tmp >> 4, tmp & 0xf, ctrl_name, trans);
- tmp = OTG_SYSCON_1_REG;
+ tmp = omap_readw(OTG_SYSCON_1);
seq_printf(s, "otg_syscon1 %08x usb2 %s, usb1 %s, usb0 %s,"
FOURBITS "\n", tmp,
trx_mode(USB2_TRX_MODE(tmp), trans & CONF_USB2_UNI_R),
@@ -2286,7 +2340,7 @@ static int proc_otg_show(struct seq_file *s)
(tmp & HST_IDLE_EN) ? " !host" : "",
(tmp & DEV_IDLE_EN) ? " !dev" : "",
(tmp & OTG_RESET_DONE) ? " reset_done" : " reset_active");
- tmp = OTG_SYSCON_2_REG;
+ tmp = omap_readl(OTG_SYSCON_2);
seq_printf(s, "otg_syscon2 %08x%s" EIGHTBITS
" b_ase_brst=%d hmc=%d\n", tmp,
(tmp & OTG_EN) ? " otg_en" : "",
@@ -2301,7 +2355,7 @@ static int proc_otg_show(struct seq_file *s)
(tmp & HMC_TLLATTACH) ? " tllattach" : "",
B_ASE_BRST(tmp),
OTG_HMC(tmp));
- tmp = OTG_CTRL_REG;
+ tmp = omap_readl(OTG_CTRL);
seq_printf(s, "otg_ctrl %06x" EIGHTBITS EIGHTBITS "%s\n", tmp,
(tmp & OTG_ASESSVLD) ? " asess" : "",
(tmp & OTG_BSESSEND) ? " bsess_end" : "",
@@ -2321,13 +2375,13 @@ static int proc_otg_show(struct seq_file *s)
(tmp & OTG_PU_VBUS) ? " pu_vb" : "",
(tmp & OTG_PU_ID) ? " pu_id" : ""
);
- tmp = OTG_IRQ_EN_REG;
+ tmp = omap_readw(OTG_IRQ_EN);
seq_printf(s, "otg_irq_en %04x" "\n", tmp);
- tmp = OTG_IRQ_SRC_REG;
+ tmp = omap_readw(OTG_IRQ_SRC);
seq_printf(s, "otg_irq_src %04x" "\n", tmp);
- tmp = OTG_OUTCTRL_REG;
+ tmp = omap_readw(OTG_OUTCTRL);
seq_printf(s, "otg_outctrl %04x" "\n", tmp);
- tmp = OTG_TEST_REG;
+ tmp = omap_readw(OTG_TEST);
seq_printf(s, "otg_test %04x" "\n", tmp);
return 0;
}
@@ -2348,7 +2402,7 @@ static int proc_udc_show(struct seq_file *s, void *_)
driver_desc,
use_dma ? " (dma)" : "");
- tmp = UDC_REV_REG & 0xff;
+ tmp = omap_readw(UDC_REV) & 0xff;
seq_printf(s,
"UDC rev %d.%d, fifo mode %d, gadget %s\n"
"hmc %d, transceiver %s\n",
@@ -2362,16 +2416,16 @@ static int proc_udc_show(struct seq_file *s, void *_)
? "external" : "(none)"));
if (cpu_class_is_omap1()) {
seq_printf(s, "ULPD control %04x req %04x status %04x\n",
- __REG16(ULPD_CLOCK_CTRL),
- __REG16(ULPD_SOFT_REQ),
- __REG16(ULPD_STATUS_REQ));
+ omap_readw(ULPD_CLOCK_CTRL),
+ omap_readw(ULPD_SOFT_REQ),
+ omap_readw(ULPD_STATUS_REQ));
}
/* OTG controller registers */
if (!cpu_is_omap15xx())
proc_otg_show(s);
- tmp = UDC_SYSCON1_REG;
+ tmp = omap_readw(UDC_SYSCON1);
seq_printf(s, "\nsyscon1 %04x" EIGHTBITS "\n", tmp,
(tmp & UDC_CFG_LOCK) ? " cfg_lock" : "",
(tmp & UDC_DATA_ENDIAN) ? " data_endian" : "",
@@ -2390,7 +2444,7 @@ static int proc_udc_show(struct seq_file *s, void *_)
return 0;
}
- tmp = UDC_DEVSTAT_REG;
+ tmp = omap_readw(UDC_DEVSTAT);
seq_printf(s, "devstat %04x" EIGHTBITS "%s%s\n", tmp,
(tmp & UDC_B_HNP_ENABLE) ? " b_hnp" : "",
(tmp & UDC_A_HNP_SUPPORT) ? " a_hnp" : "",
@@ -2402,20 +2456,20 @@ static int proc_udc_show(struct seq_file *s, void *_)
(tmp & UDC_ADD) ? " ADD" : "",
(tmp & UDC_DEF) ? " DEF" : "",
(tmp & UDC_ATT) ? " ATT" : "");
- seq_printf(s, "sof %04x\n", UDC_SOF_REG);
- tmp = UDC_IRQ_EN_REG;
+ seq_printf(s, "sof %04x\n", omap_readw(UDC_SOF));
+ tmp = omap_readw(UDC_IRQ_EN);
seq_printf(s, "irq_en %04x" FOURBITS "%s\n", tmp,
(tmp & UDC_SOF_IE) ? " sof" : "",
(tmp & UDC_EPN_RX_IE) ? " epn_rx" : "",
(tmp & UDC_EPN_TX_IE) ? " epn_tx" : "",
(tmp & UDC_DS_CHG_IE) ? " ds_chg" : "",
(tmp & UDC_EP0_IE) ? " ep0" : "");
- tmp = UDC_IRQ_SRC_REG;
+ tmp = omap_readw(UDC_IRQ_SRC);
seq_printf(s, "irq_src %04x" EIGHTBITS "%s%s\n", tmp,
(tmp & UDC_TXN_DONE) ? " txn_done" : "",
(tmp & UDC_RXN_CNT) ? " rxn_cnt" : "",
(tmp & UDC_RXN_EOT) ? " rxn_eot" : "",
- (tmp & UDC_SOF) ? " sof" : "",
+ (tmp & UDC_IRQ_SOF) ? " sof" : "",
(tmp & UDC_EPN_RX) ? " epn_rx" : "",
(tmp & UDC_EPN_TX) ? " epn_tx" : "",
(tmp & UDC_DS_CHG) ? " ds_chg" : "",
@@ -2425,7 +2479,7 @@ static int proc_udc_show(struct seq_file *s, void *_)
if (use_dma) {
unsigned i;
- tmp = UDC_DMA_IRQ_EN_REG;
+ tmp = omap_readw(UDC_DMA_IRQ_EN);
seq_printf(s, "dma_irq_en %04x%s" EIGHTBITS "\n", tmp,
(tmp & UDC_TX_DONE_IE(3)) ? " tx2_done" : "",
(tmp & UDC_RX_CNT_IE(3)) ? " rx2_cnt" : "",
@@ -2439,29 +2493,29 @@ static int proc_udc_show(struct seq_file *s, void *_)
(tmp & UDC_RX_CNT_IE(1)) ? " rx0_cnt" : "",
(tmp & UDC_RX_EOT_IE(1)) ? " rx0_eot" : "");
- tmp = UDC_RXDMA_CFG_REG;
+ tmp = omap_readw(UDC_RXDMA_CFG);
seq_printf(s, "rxdma_cfg %04x\n", tmp);
if (tmp) {
for (i = 0; i < 3; i++) {
if ((tmp & (0x0f << (i * 4))) == 0)
continue;
seq_printf(s, "rxdma[%d] %04x\n", i,
- UDC_RXDMA_REG(i + 1));
+ omap_readw(UDC_RXDMA(i + 1)));
}
}
- tmp = UDC_TXDMA_CFG_REG;
+ tmp = omap_readw(UDC_TXDMA_CFG);
seq_printf(s, "txdma_cfg %04x\n", tmp);
if (tmp) {
for (i = 0; i < 3; i++) {
if (!(tmp & (0x0f << (i * 4))))
continue;
seq_printf(s, "txdma[%d] %04x\n", i,
- UDC_TXDMA_REG(i + 1));
+ omap_readw(UDC_TXDMA(i + 1)));
}
}
}
- tmp = UDC_DEVSTAT_REG;
+ tmp = omap_readw(UDC_DEVSTAT);
if (tmp & UDC_ATT) {
proc_ep_show(s, &udc->ep[0]);
if (tmp & UDC_ADD) {
@@ -2513,7 +2567,7 @@ static inline void remove_proc_file(void) {}
* buffer space among the endpoints we'll be operating.
*
* NOTE: as of OMAP 1710 ES2.0, writing a new endpoint config when
- * UDC_SYSCON_1_REG.CFG_LOCK is set can now work. We won't use that
+ * UDC_SYSCON_1.CFG_LOCK is set can now work. We won't use that
* capability yet though.
*/
static unsigned __init
@@ -2577,9 +2631,9 @@ omap_ep_setup(char *name, u8 addr, u8 type,
name, addr, epn_rxtx, maxp, dbuf ? "x2" : "", buf);
if (addr & USB_DIR_IN)
- UDC_EP_TX_REG(addr & 0xf) = epn_rxtx;
+ omap_writew(epn_rxtx, UDC_EP_TX(addr & 0xf));
else
- UDC_EP_RX_REG(addr) = epn_rxtx;
+ omap_writew(epn_rxtx, UDC_EP_RX(addr));
/* next endpoint's buffer starts after this one's */
buf += maxp;
@@ -2618,15 +2672,15 @@ omap_udc_setup(struct platform_device *odev, struct otg_transceiver *xceiv)
unsigned tmp, buf;
/* abolish any previous hardware state */
- UDC_SYSCON1_REG = 0;
- UDC_IRQ_EN_REG = 0;
- UDC_IRQ_SRC_REG = UDC_IRQ_SRC_MASK;
- UDC_DMA_IRQ_EN_REG = 0;
- UDC_RXDMA_CFG_REG = 0;
- UDC_TXDMA_CFG_REG = 0;
+ omap_writew(0, UDC_SYSCON1);
+ omap_writew(0, UDC_IRQ_EN);
+ omap_writew(UDC_IRQ_SRC_MASK, UDC_IRQ_SRC);
+ omap_writew(0, UDC_DMA_IRQ_EN);
+ omap_writew(0, UDC_RXDMA_CFG);
+ omap_writew(0, UDC_TXDMA_CFG);
/* UDC_PULLUP_EN gates the chip clock */
- // OTG_SYSCON_1_REG |= DEV_IDLE_EN;
+ // OTG_SYSCON_1 |= DEV_IDLE_EN;
udc = kzalloc(sizeof(*udc), GFP_KERNEL);
if (!udc)
@@ -2657,8 +2711,8 @@ omap_udc_setup(struct platform_device *odev, struct otg_transceiver *xceiv)
/* initially disable all non-ep0 endpoints */
for (tmp = 1; tmp < 15; tmp++) {
- UDC_EP_RX_REG(tmp) = 0;
- UDC_EP_TX_REG(tmp) = 0;
+ omap_writew(0, UDC_EP_RX(tmp));
+ omap_writew(0, UDC_EP_TX(tmp));
}
#define OMAP_BULK_EP(name,addr) \
@@ -2743,7 +2797,7 @@ omap_udc_setup(struct platform_device *odev, struct otg_transceiver *xceiv)
ERR("unsupported fifo_mode #%d\n", fifo_mode);
return -ENODEV;
}
- UDC_SYSCON1_REG = UDC_CFG_LOCK|UDC_SELF_PWR;
+ omap_writew(UDC_CFG_LOCK|UDC_SELF_PWR, UDC_SYSCON1);
INFO("fifo mode %d, %d bytes not used\n", fifo_mode, 2048 - buf);
return 0;
}
@@ -2787,7 +2841,7 @@ static int __init omap_udc_probe(struct platform_device *pdev)
}
INFO("OMAP UDC rev %d.%d%s\n",
- UDC_REV_REG >> 4, UDC_REV_REG & 0xf,
+ omap_readw(UDC_REV) >> 4, omap_readw(UDC_REV) & 0xf,
config->otg ? ", Mini-AB" : "");
/* use the mode given to us by board init code */
@@ -2802,12 +2856,12 @@ static int __init omap_udc_probe(struct platform_device *pdev)
* know when to turn PULLUP_EN on/off; and that
* means we always "need" the 48MHz clock.
*/
- u32 tmp = FUNC_MUX_CTRL_0_REG;
-
- FUNC_MUX_CTRL_0_REG &= ~VBUS_CTRL_1510;
+ u32 tmp = omap_readl(FUNC_MUX_CTRL_0);
+ tmp &= ~VBUS_CTRL_1510;
+ omap_writel(tmp, FUNC_MUX_CTRL_0);
tmp |= VBUS_MODE_1510;
tmp &= ~VBUS_CTRL_1510;
- FUNC_MUX_CTRL_0_REG = tmp;
+ omap_writel(tmp, FUNC_MUX_CTRL_0);
}
} else {
/* The transceiver may package some GPIO logic or handle
@@ -2887,7 +2941,7 @@ known:
#endif
/* starting with omap1710 es2.0, clear toggle is a separate bit */
- if (UDC_REV_REG >= 0x61)
+ if (omap_readw(UDC_REV) >= 0x61)
udc->clr_halt = UDC_RESET_EP | UDC_CLRDATA_TOGGLE;
else
udc->clr_halt = UDC_RESET_EP;
@@ -2985,7 +3039,7 @@ static int __exit omap_udc_remove(struct platform_device *pdev)
put_device(udc->transceiver->dev);
udc->transceiver = NULL;
}
- UDC_SYSCON1_REG = 0;
+ omap_writew(0, UDC_SYSCON1);
remove_proc_file();
@@ -3016,7 +3070,7 @@ static int __exit omap_udc_remove(struct platform_device *pdev)
*
* REVISIT we should probably reject suspend requests when there's a host
* session active, rather than disconnecting, at least on boards that can
- * report VBUS irqs (UDC_DEVSTAT_REG.UDC_ATT). And in any case, we need to
+ * report VBUS irqs (UDC_DEVSTAT.UDC_ATT). And in any case, we need to
* make host resumes and VBUS detection trigger OMAP wakeup events; that
* may involve talking to an external transceiver (e.g. isp1301).
*/
@@ -3025,7 +3079,7 @@ static int omap_udc_suspend(struct platform_device *dev, pm_message_t message)
{
u32 devstat;
- devstat = UDC_DEVSTAT_REG;
+ devstat = omap_readw(UDC_DEVSTAT);
/* we're requesting 48 MHz clock if the pullup is enabled
* (== we're attached to the host) and we're not suspended,
diff --git a/drivers/usb/gadget/omap_udc.h b/drivers/usb/gadget/omap_udc.h
index c6b9cbc..8522bbb 100644
--- a/drivers/usb/gadget/omap_udc.h
+++ b/drivers/usb/gadget/omap_udc.h
@@ -8,23 +8,22 @@
/*
* USB device/endpoint management registers
*/
-#define UDC_REG(offset) __REG16(UDC_BASE + (offset))
-#define UDC_REV_REG UDC_REG(0x0) /* Revision */
-#define UDC_EP_NUM_REG UDC_REG(0x4) /* Which endpoint */
+#define UDC_REV (UDC_BASE + 0x0) /* Revision */
+#define UDC_EP_NUM (UDC_BASE + 0x4) /* Which endpoint */
# define UDC_SETUP_SEL (1 << 6)
# define UDC_EP_SEL (1 << 5)
# define UDC_EP_DIR (1 << 4)
/* low 4 bits for endpoint number */
-#define UDC_DATA_REG UDC_REG(0x08) /* Endpoint FIFO */
-#define UDC_CTRL_REG UDC_REG(0x0C) /* Endpoint control */
+#define UDC_DATA (UDC_BASE + 0x08) /* Endpoint FIFO */
+#define UDC_CTRL (UDC_BASE + 0x0C) /* Endpoint control */
# define UDC_CLR_HALT (1 << 7)
# define UDC_SET_HALT (1 << 6)
# define UDC_CLRDATA_TOGGLE (1 << 3)
# define UDC_SET_FIFO_EN (1 << 2)
# define UDC_CLR_EP (1 << 1)
# define UDC_RESET_EP (1 << 0)
-#define UDC_STAT_FLG_REG UDC_REG(0x10) /* Endpoint status */
+#define UDC_STAT_FLG (UDC_BASE + 0x10) /* Endpoint status */
# define UDC_NO_RXPACKET (1 << 15)
# define UDC_MISS_IN (1 << 14)
# define UDC_DATA_FLUSH (1 << 13)
@@ -38,8 +37,8 @@
# define UDC_FIFO_EN (1 << 2)
# define UDC_NON_ISO_FIFO_EMPTY (1 << 1)
# define UDC_NON_ISO_FIFO_FULL (1 << 0)
-#define UDC_RXFSTAT_REG UDC_REG(0x14) /* OUT bytecount */
-#define UDC_SYSCON1_REG UDC_REG(0x18) /* System config 1 */
+#define UDC_RXFSTAT (UDC_BASE + 0x14) /* OUT bytecount */
+#define UDC_SYSCON1 (UDC_BASE + 0x18) /* System config 1 */
# define UDC_CFG_LOCK (1 << 8)
# define UDC_DATA_ENDIAN (1 << 7)
# define UDC_DMA_ENDIAN (1 << 6)
@@ -48,12 +47,12 @@
# define UDC_SELF_PWR (1 << 2)
# define UDC_SOFF_DIS (1 << 1)
# define UDC_PULLUP_EN (1 << 0)
-#define UDC_SYSCON2_REG UDC_REG(0x1C) /* System config 2 */
+#define UDC_SYSCON2 (UDC_BASE + 0x1C) /* System config 2 */
# define UDC_RMT_WKP (1 << 6)
# define UDC_STALL_CMD (1 << 5)
# define UDC_DEV_CFG (1 << 3)
# define UDC_CLR_CFG (1 << 2)
-#define UDC_DEVSTAT_REG UDC_REG(0x20) /* Device status */
+#define UDC_DEVSTAT (UDC_BASE + 0x20) /* Device status */
# define UDC_B_HNP_ENABLE (1 << 9)
# define UDC_A_HNP_SUPPORT (1 << 8)
# define UDC_A_ALT_HNP_SUPPORT (1 << 7)
@@ -64,26 +63,26 @@
# define UDC_ADD (1 << 2)
# define UDC_DEF (1 << 1)
# define UDC_ATT (1 << 0)
-#define UDC_SOF_REG UDC_REG(0x24) /* Start of frame */
+#define UDC_SOF (UDC_BASE + 0x24) /* Start of frame */
# define UDC_FT_LOCK (1 << 12)
# define UDC_TS_OK (1 << 11)
# define UDC_TS 0x03ff
-#define UDC_IRQ_EN_REG UDC_REG(0x28) /* Interrupt enable */
+#define UDC_IRQ_EN (UDC_BASE + 0x28) /* Interrupt enable */
# define UDC_SOF_IE (1 << 7)
# define UDC_EPN_RX_IE (1 << 5)
# define UDC_EPN_TX_IE (1 << 4)
# define UDC_DS_CHG_IE (1 << 3)
# define UDC_EP0_IE (1 << 0)
-#define UDC_DMA_IRQ_EN_REG UDC_REG(0x2C) /* DMA irq enable */
+#define UDC_DMA_IRQ_EN (UDC_BASE + 0x2C) /* DMA irq enable */
/* rx/tx dma channels numbered 1-3 not 0-2 */
# define UDC_TX_DONE_IE(n) (1 << (4 * (n) - 2))
# define UDC_RX_CNT_IE(n) (1 << (4 * (n) - 3))
# define UDC_RX_EOT_IE(n) (1 << (4 * (n) - 4))
-#define UDC_IRQ_SRC_REG UDC_REG(0x30) /* Interrupt source */
+#define UDC_IRQ_SRC (UDC_BASE + 0x30) /* Interrupt source */
# define UDC_TXN_DONE (1 << 10)
# define UDC_RXN_CNT (1 << 9)
# define UDC_RXN_EOT (1 << 8)
-# define UDC_SOF (1 << 7)
+# define UDC_IRQ_SOF (1 << 7)
# define UDC_EPN_RX (1 << 5)
# define UDC_EPN_TX (1 << 4)
# define UDC_DS_CHG (1 << 3)
@@ -91,41 +90,41 @@
# define UDC_EP0_RX (1 << 1)
# define UDC_EP0_TX (1 << 0)
# define UDC_IRQ_SRC_MASK 0x7bf
-#define UDC_EPN_STAT_REG UDC_REG(0x34) /* EP irq status */
-#define UDC_DMAN_STAT_REG UDC_REG(0x38) /* DMA irq status */
+#define UDC_EPN_STAT (UDC_BASE + 0x34) /* EP irq status */
+#define UDC_DMAN_STAT (UDC_BASE + 0x38) /* DMA irq status */
# define UDC_DMA_RX_SB (1 << 12)
# define UDC_DMA_RX_SRC(x) (((x)>>8) & 0xf)
# define UDC_DMA_TX_SRC(x) (((x)>>0) & 0xf)
/* DMA configuration registers: up to three channels in each direction. */
-#define UDC_RXDMA_CFG_REG UDC_REG(0x40) /* 3 eps for RX DMA */
+#define UDC_RXDMA_CFG (UDC_BASE + 0x40) /* 3 eps for RX DMA */
# define UDC_DMA_REQ (1 << 12)
-#define UDC_TXDMA_CFG_REG UDC_REG(0x44) /* 3 eps for TX DMA */
-#define UDC_DATA_DMA_REG UDC_REG(0x48) /* rx/tx fifo addr */
+#define UDC_TXDMA_CFG (UDC_BASE + 0x44) /* 3 eps for TX DMA */
+#define UDC_DATA_DMA (UDC_BASE + 0x48) /* rx/tx fifo addr */
/* rx/tx dma control, numbering channels 1-3 not 0-2 */
-#define UDC_TXDMA_REG(chan) UDC_REG(0x50 - 4 + 4 * (chan))
+#define UDC_TXDMA(chan) (UDC_BASE + 0x50 - 4 + 4 * (chan))
# define UDC_TXN_EOT (1 << 15) /* bytes vs packets */
# define UDC_TXN_START (1 << 14) /* start transfer */
# define UDC_TXN_TSC 0x03ff /* units in xfer */
-#define UDC_RXDMA_REG(chan) UDC_REG(0x60 - 4 + 4 * (chan))
+#define UDC_RXDMA(chan) (UDC_BASE + 0x60 - 4 + 4 * (chan))
# define UDC_RXN_STOP (1 << 15) /* enable EOT irq */
# define UDC_RXN_TC 0x00ff /* packets in xfer */
/*
* Endpoint configuration registers (used before CFG_LOCK is set)
- * UDC_EP_TX_REG(0) is unused
+ * UDC_EP_TX(0) is unused
*/
-#define UDC_EP_RX_REG(endpoint) UDC_REG(0x80 + (endpoint)*4)
+#define UDC_EP_RX(endpoint) (UDC_BASE + 0x80 + (endpoint)*4)
# define UDC_EPN_RX_VALID (1 << 15)
# define UDC_EPN_RX_DB (1 << 14)
/* buffer size in bits 13, 12 */
# define UDC_EPN_RX_ISO (1 << 11)
/* buffer pointer in low 11 bits */
-#define UDC_EP_TX_REG(endpoint) UDC_REG(0xc0 + (endpoint)*4)
- /* same bitfields as in RX_REG */
+#define UDC_EP_TX(endpoint) (UDC_BASE + 0xc0 + (endpoint)*4)
+ /* same bitfields as in RX */
/*-------------------------------------------------------------------------*/
@@ -195,14 +194,14 @@ struct omap_udc {
/*-------------------------------------------------------------------------*/
-#define MOD_CONF_CTRL_0_REG __REG32(MOD_CONF_CTRL_0)
-#define VBUS_W2FC_1510 (1 << 17) /* 0 gpio0, 1 dvdd2 pin */
+/* MOD_CONF_CTRL_0 */
+#define VBUS_W2FC_1510 (1 << 17) /* 0 gpio0, 1 dvdd2 pin */
-#define FUNC_MUX_CTRL_0_REG __REG32(FUNC_MUX_CTRL_0)
+/* FUNC_MUX_CTRL_0 */
#define VBUS_CTRL_1510 (1 << 19) /* 1 connected (software) */
#define VBUS_MODE_1510 (1 << 18) /* 0 hardware, 1 software */
-#define HMC_1510 ((MOD_CONF_CTRL_0_REG >> 1) & 0x3f)
-#define HMC_1610 (OTG_SYSCON_2_REG & 0x3f)
+#define HMC_1510 ((omap_readl(MOD_CONF_CTRL_0) >> 1) & 0x3f)
+#define HMC_1610 (omap_readl(OTG_SYSCON_2) & 0x3f)
#define HMC (cpu_is_omap15xx() ? HMC_1510 : HMC_1610)
diff --git a/drivers/usb/host/ohci-omap.c b/drivers/usb/host/ohci-omap.c
index f14be49..c23caf6 100644
--- a/drivers/usb/host/ohci-omap.c
+++ b/drivers/usb/host/ohci-omap.c
@@ -169,13 +169,16 @@ static void start_hnp(struct ohci_hcd *ohci)
{
const unsigned port = ohci_to_hcd(ohci)->self.otg_port - 1;
unsigned long flags;
+ u32 l;
otg_start_hnp(ohci->transceiver);
local_irq_save(flags);
ohci->transceiver->state = OTG_STATE_A_SUSPEND;
writel (RH_PS_PSS, &ohci->regs->roothub.portstatus [port]);
- OTG_CTRL_REG &= ~OTG_A_BUSREQ;
+ l = omap_readl(OTG_CTRL);
+ l &= ~OTG_A_BUSREQ;
+ omap_writel(l, OTG_CTRL);
local_irq_restore(flags);
}
diff --git a/include/asm-arm/arch-omap/usb.h b/include/asm-arm/arch-omap/usb.h
index 580a718..7a0967b 100644
--- a/include/asm-arm/arch-omap/usb.h
+++ b/include/asm-arm/arch-omap/usb.h
@@ -37,11 +37,8 @@ void __init usb_ehci_init(void);
/*
* OTG and transceiver registers, for OMAPs starting with ARM926
*/
-#define OTG_REG32(offset) __REG32(OTG_BASE + (offset))
-#define OTG_REG16(offset) __REG16(OTG_BASE + (offset))
-
-#define OTG_REV_REG OTG_REG32(0x00)
-#define OTG_SYSCON_1_REG OTG_REG32(0x04)
+#define OTG_REV (OTG_BASE + 0x00)
+#define OTG_SYSCON_1 (OTG_BASE + 0x04)
# define USB2_TRX_MODE(w) (((w)>>24)&0x07)
# define USB1_TRX_MODE(w) (((w)>>20)&0x07)
# define USB0_TRX_MODE(w) (((w)>>16)&0x07)
@@ -50,7 +47,7 @@ void __init usb_ehci_init(void);
# define DEV_IDLE_EN (1 << 13)
# define OTG_RESET_DONE (1 << 2)
# define OTG_SOFT_RESET (1 << 1)
-#define OTG_SYSCON_2_REG OTG_REG32(0x08)
+#define OTG_SYSCON_2 (OTG_BASE + 0x08)
# define OTG_EN (1 << 31)
# define USBX_SYNCHRO (1 << 30)
# define OTG_MST16 (1 << 29)
@@ -68,7 +65,7 @@ void __init usb_ehci_init(void);
# define HMC_TLLSPEED (1 << 7)
# define HMC_TLLATTACH (1 << 6)
# define OTG_HMC(w) (((w)>>0)&0x3f)
-#define OTG_CTRL_REG OTG_REG32(0x0c)
+#define OTG_CTRL (OTG_BASE + 0x0c)
# define OTG_USB2_EN (1 << 29)
# define OTG_USB2_DP (1 << 28)
# define OTG_USB2_DM (1 << 27)
@@ -95,7 +92,7 @@ void __init usb_ehci_init(void);
# define OTG_PD_VBUS (1 << 2)
# define OTG_PU_VBUS (1 << 1)
# define OTG_PU_ID (1 << 0)
-#define OTG_IRQ_EN_REG OTG_REG16(0x10)
+#define OTG_IRQ_EN (OTG_BASE + 0x10) /* 16-bit */
# define DRIVER_SWITCH (1 << 15)
# define A_VBUS_ERR (1 << 13)
# define A_REQ_TMROUT (1 << 12)
@@ -105,9 +102,9 @@ void __init usb_ehci_init(void);
# define B_SRP_DONE (1 << 8)
# define B_SRP_STARTED (1 << 7)
# define OPRT_CHG (1 << 0)
-#define OTG_IRQ_SRC_REG OTG_REG16(0x14)
+#define OTG_IRQ_SRC (OTG_BASE + 0x14) /* 16-bit */
// same bits as in IRQ_EN
-#define OTG_OUTCTRL_REG OTG_REG16(0x18)
+#define OTG_OUTCTRL (OTG_BASE + 0x18) /* 16-bit */
# define OTGVPD (1 << 14)
# define OTGVPU (1 << 13)
# define OTGPUID (1 << 12)
@@ -120,13 +117,13 @@ void __init usb_ehci_init(void);
# define USB0VDR (1 << 2)
# define USB0PDEN (1 << 1)
# define USB0PUEN (1 << 0)
-#define OTG_TEST_REG OTG_REG16(0x20)
-#define OTG_VENDOR_CODE_REG OTG_REG32(0xfc)
+#define OTG_TEST (OTG_BASE + 0x20) /* 16-bit */
+#define OTG_VENDOR_CODE (OTG_BASE + 0xfc) /* 16-bit */
/*-------------------------------------------------------------------------*/
/* OMAP1 */
-#define USB_TRANSCEIVER_CTRL_REG __REG32(0xfffe1000 + 0x0064)
+#define USB_TRANSCEIVER_CTRL (0xfffe1000 + 0x0064)
# define CONF_USB2_UNI_R (1 << 8)
# define CONF_USB1_UNI_R (1 << 7)
# define CONF_USB_PORT0_R(x) (((x)>>4)&0x7)
--
1.5.3.6
next prev parent reply other threads:[~2008-05-28 4:20 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-05-28 4:20 [PATCH 0/14] Big clean-up for multi-omap Tony Lindgren
2008-05-28 4:20 ` [PATCH 1/14] ARM: OMAP: Fix debug-macro for multi_omap Tony Lindgren
2008-05-28 4:20 ` [PATCH 2/14] CF: Change omap_cf.c to use omap_readw/writew instead of __REG for multi-omap Tony Lindgren
2008-05-28 4:20 ` Tony Lindgren [this message]
2008-05-28 4:20 ` [PATCH 4/14] ARM: OMAP: Change __REG access to omap/read write for traffic controller Tony Lindgren
2008-05-28 4:20 ` [PATCH 5/14] musb_hdrc: Change __REG access to omap_read/write for multi-boot Tony Lindgren
2008-05-28 4:20 ` [PATCH 6/14] ARM: OMAP: Remove __REG access for multi-omap Tony Lindgren
2008-05-28 4:20 ` [PATCH 7/14] ARM: OMAP: Split sleep24xx.S into sleep242x.S and sleep243x.S Tony Lindgren
2008-05-28 4:20 ` [PATCH 8/14] ARM: OMAP: Split sram24xx.S into sram242x.S and sram243x.S Tony Lindgren
2008-05-28 4:20 ` [PATCH 9/14] ARM: OMAP: Remove omap_sram_patch_va Tony Lindgren
2008-05-28 4:20 ` [PATCH 10/14] ARM: OMAP: Introduce omap_globals and prcm access functions for multi-omap Tony Lindgren
2008-05-28 4:20 ` [PATCH 11/14] ARM: OMAP: Remove OMAP_PRM_REGADDR Tony Lindgren
2008-05-28 4:20 ` [PATCH 12/14] ARM: OMAP: Remove OMAP_CM_REGADDR for multi-boot Tony Lindgren
2008-05-28 4:20 ` [PATCH 13/14] ARM: OMAP: Change to use CM offsets for clocks for multi-omap Tony Lindgren
2008-05-28 4:20 ` [PATCH 14/14] ARM: OMAP: Use omap_globals for CPU detection " Tony Lindgren
2008-05-30 21:41 ` [PATCH 0/14] Big clean-up " Tony Lindgren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1211948418-16455-4-git-send-email-tony@atomide.com \
--to=tony@atomide.com \
--cc=linux-omap@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox