From mboxrd@z Thu Jan 1 00:00:00 1970 From: Thomas Weber Subject: [PATCH 04/14] OMAP2: Devkit8000: Setup LCD reset Date: Tue, 18 May 2010 14:05:25 +0200 Message-ID: <1274184335-29322-5-git-send-email-weber@corscience.de> References: <1274184335-29322-1-git-send-email-weber@corscience.de> Return-path: Received: from moutng.kundenserver.de ([212.227.17.10]:56252 "EHLO moutng.kundenserver.de" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1757420Ab0ERMGI (ORCPT ); Tue, 18 May 2010 08:06:08 -0400 In-Reply-To: <1274184335-29322-1-git-send-email-weber@corscience.de> Sender: linux-omap-owner@vger.kernel.org List-Id: linux-omap@vger.kernel.org To: linux-omap@vger.kernel.org Cc: tony@atomide.com, Kan-Ru Chen , Thomas Weber From: Kan-Ru Chen This patch corrects the LCD reset pin config. Original code from early devkit8000 patch sets the TWL4030 GPIO_1 to EHCI_nOC and TWL4030_GPIO_MAX+1 to ledA. Indeed these two pins are both LCD_PWREN. Setup the lcd reset_gpio properly so it can be disabled when other display is turned on. Signed-off-by: Kan-Ru Chen Signed-off-by: Thomas Weber --- arch/arm/mach-omap2/board-devkit8000.c | 11 +++++++++++ 1 files changed, 11 insertions(+), 0 deletions(-) diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c index c6b9ed4..37b047e 100644 --- a/arch/arm/mach-omap2/board-devkit8000.c +++ b/arch/arm/mach-omap2/board-devkit8000.c @@ -134,11 +134,15 @@ static int devkit8000_panel_enable_lcd(struct omap_dss_device *dssdev) twl_i2c_write_u8(TWL4030_MODULE_GPIO, 0x80, REG_GPIODATADIR1); twl_i2c_write_u8(TWL4030_MODULE_LED, 0x0, 0x0); + if (dssdev->reset_gpio != -EINVAL) + gpio_set_value(dssdev->reset_gpio, 1); return 0; } static void devkit8000_panel_disable_lcd(struct omap_dss_device *dssdev) { + if (dssdev->reset_gpio != -EINVAL) + gpio_set_value(dssdev->reset_gpio, 0); } static int devkit8000_panel_enable_dvi(struct omap_dss_device *dssdev) @@ -183,6 +187,7 @@ static struct omap_dss_device devkit8000_lcd_device = { .driver_name = "generic_panel", .type = OMAP_DISPLAY_TYPE_DPI, .phy.dpi.data_lines = 24, + .reset_gpio = -EINVAL, /* will be replaced */ .platform_enable = devkit8000_panel_enable_lcd, .platform_disable = devkit8000_panel_disable_lcd, }; @@ -281,6 +286,12 @@ static int devkit8000_twl_gpio_setup(struct device *dev, /* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */ gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1; + /* gpio + 1 is "LCD_PWREN" (out, active high) */ + devkit8000_lcd_device.reset_gpio = gpio + 1; + gpio_request(devkit8000_lcd_device.reset_gpio, "LCD_PWREN"); + /* Disable until needed */ + gpio_direction_output(devkit8000_lcd_device.reset_gpio, 0); + /* gpio + 7 is "DVI_PD" (out, active low) */ devkit8000_dvi_device.reset_gpio = gpio + 7; gpio_request(devkit8000_dvi_device.reset_gpio, "DVI PowerDown"); -- 1.6.4.4