From: Thomas Weber <weber@corscience.de>
To: linux-omap@vger.kernel.org
Cc: tony@atomide.com, Thomas Weber <weber@corscience.de>
Subject: [PATCH 06/14] OMAP2: Devkit8000: Remove nonexisting vsim
Date: Tue, 18 May 2010 14:05:27 +0200 [thread overview]
Message-ID: <1274184335-29322-7-git-send-email-weber@corscience.de> (raw)
In-Reply-To: <1274184335-29322-1-git-send-email-weber@corscience.de>
The Devkit8000 uses the cost reduced variant tps65930 of the twl4030.
The TPS65930 only has vdd1, vdd2, vpll1, vio, vmmc1, vdac and vaux2.
vaux2 is not used.
Signed-off-by: Thomas Weber <weber@corscience.de>
---
arch/arm/mach-omap2/board-devkit8000.c | 22 ----------------------
1 files changed, 0 insertions(+), 22 deletions(-)
diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 4611274..7d68016 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -168,15 +168,10 @@ static void devkit8000_panel_disable_tv(struct omap_dss_device *dssdev)
{
}
-
static struct regulator_consumer_supply devkit8000_vmmc1_supply = {
.supply = "vmmc",
};
-static struct regulator_consumer_supply devkit8000_vsim_supply = {
- .supply = "vmmc_aux",
-};
-
/* ads7846 on SPI */
static struct regulator_consumer_supply devkit8000_vio_supplies[] = {
REGULATOR_SUPPLY("vcc", "spi2.0")
@@ -281,7 +276,6 @@ static int devkit8000_twl_gpio_setup(struct device *dev,
/* link regulators to MMC adapters */
devkit8000_vmmc1_supply.dev = mmc[0].dev;
- devkit8000_vsim_supply.dev = mmc[0].dev;
/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
@@ -334,21 +328,6 @@ static struct regulator_init_data devkit8000_vmmc1 = {
.consumer_supplies = &devkit8000_vmmc1_supply,
};
-/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
-static struct regulator_init_data devkit8000_vsim = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 3000000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = 1,
- .consumer_supplies = &devkit8000_vsim_supply,
-};
-
/* VDAC for DSS driving S-Video (8 mA unloaded, max 65 mA) */
static struct regulator_init_data devkit8000_vdac = {
.constraints = {
@@ -414,7 +393,6 @@ static struct twl4030_platform_data devkit8000_twldata = {
.gpio = &devkit8000_gpio_data,
.codec = &devkit8000_codec_data,
.vmmc1 = &devkit8000_vmmc1,
- .vsim = &devkit8000_vsim,
.vdac = &devkit8000_vdac,
.vpll1 = &devkit8000_vpll1,
.vio = &devkit8000_vio,
--
1.6.4.4
next prev parent reply other threads:[~2010-05-18 12:06 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-05-18 12:05 [PATCH 00/14] Multiple fixes for Devkit8000 Thomas Weber
2010-05-18 12:05 ` [PATCH 01/14] OMAP2: Devkit8000: Cleanup for supplies Thomas Weber
2010-05-18 12:05 ` [PATCH 02/14] OMAP2: Devkit8000: change lcd panel to generic Thomas Weber
2010-05-18 12:05 ` [PATCH 03/14] OMAP2: Devkit8000: Enable DVI-D output Thomas Weber
2010-05-18 12:05 ` [PATCH 04/14] OMAP2: Devkit8000: Setup LCD reset Thomas Weber
2010-05-18 12:05 ` [PATCH 05/14] OMAP2: Devkit8000: Remove unneeded VDVI Thomas Weber
2010-05-18 12:05 ` Thomas Weber [this message]
2010-05-18 12:05 ` [PATCH 07/14] OMAP2: Devkit8000: Remove en-/disable for tv panel Thomas Weber
2010-05-18 12:05 ` [PATCH 08/14] OMAP2: Devkit8000: Use the REGULATOR_SUPPLY macro Thomas Weber
2010-05-18 12:05 ` [PATCH 09/14] OMAP2: Devkit8000: Fixing comment about pins used Thomas Weber
2010-05-18 12:05 ` [PATCH 10/14] OMAP2: Devkit8000: Fix whitespace with tab Thomas Weber
2010-05-18 12:05 ` [PATCH 11/14] OMAP2: Devkit8000: Fix comment Thomas Weber
2010-05-18 12:05 ` [PATCH 12/14] OMAP2: Devkit8000: Using gpio_is_valid Thomas Weber
2010-05-18 12:05 ` [PATCH 13/14] OMAP2: Devkit8000: Remove unused omap_board_config Thomas Weber
2010-05-18 12:05 ` [PATCH 14/14] OMAP2: Devkit8000: Correct regulator Thomas Weber
2010-05-19 4:02 ` [PATCH 00/14] Multiple fixes for Devkit8000 Kan-Ru Chen
2010-06-01 5:36 ` Thomas Weber
2010-06-01 8:32 ` Tony Lindgren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1274184335-29322-7-git-send-email-weber@corscience.de \
--to=weber@corscience.de \
--cc=linux-omap@vger.kernel.org \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).