* Initial B&N Nook Color support, take two
@ 2011-04-28 15:57 green
2011-04-28 15:57 ` [PATCH 1/2] Initial B&N Nook Color (encore) support green
` (2 more replies)
0 siblings, 3 replies; 9+ messages in thread
From: green @ 2011-04-28 15:57 UTC (permalink / raw)
To: linux-omap
Hello!
Ok, this is a second attempt at B&N Nook Color board file submission.
USB peripheral mode is fully operational as is serial console and
MMC/SDCard.
I threw away all the android stuff as suggested, also cleaned up
voltage regulators and removed the ones our twl chip actually
does not have (contrary to my previous beliefs).
Bye,
Oleg
^ permalink raw reply [flat|nested] 9+ messages in thread* [PATCH 1/2] Initial B&N Nook Color (encore) support. 2011-04-28 15:57 Initial B&N Nook Color support, take two green @ 2011-04-28 15:57 ` green 2011-04-28 23:34 ` Abimanyu Gottumukkala 2011-05-03 9:22 ` Tony Lindgren 2011-04-28 15:57 ` [PATCH 2/2] Add tps65921 chip green 2011-04-28 17:05 ` Initial B&N Nook Color support, take two Paul Walmsley 2 siblings, 2 replies; 9+ messages in thread From: green @ 2011-04-28 15:57 UTC (permalink / raw) To: linux-omap; +Cc: Oleg Drokin From: Oleg Drokin <green@linuxhacker.ru> Bare-bones board file, comes with serial console, gpio keys, MMC/SDCard and USB support. --- arch/arm/mach-omap2/Kconfig | 5 + arch/arm/mach-omap2/Makefile | 2 + arch/arm/mach-omap2/board-omap3encore.c | 380 ++++++++++++++++++++++++++ arch/arm/plat-omap/include/plat/uncompress.h | 1 + arch/arm/tools/mach-types | 2 +- 5 files changed, 389 insertions(+), 1 deletions(-) create mode 100644 arch/arm/mach-omap2/board-omap3encore.c diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig index b997a35..5370561 100644 --- a/arch/arm/mach-omap2/Kconfig +++ b/arch/arm/mach-omap2/Kconfig @@ -173,6 +173,11 @@ config MACH_OMAP3_TORPEDO for full description please see the products webpage at http://www.logicpd.com/products/development-kits/zoom-omap35x-torpedo-development-kit +config MACH_ENCORE + bool "Barnes & Noble Encore (Nook Color)" + depends on ARCH_OMAP3 + select OMAP_PACKAGE_CBP + config MACH_OVERO bool "Gumstix Overo board" depends on ARCH_OMAP3 diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index 512b152..b894777 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -189,6 +189,8 @@ obj-$(CONFIG_MACH_OMAP3530_LV_SOM) += board-omap3logic.o \ hsmmc.o obj-$(CONFIG_MACH_OMAP3_TORPEDO) += board-omap3logic.o \ hsmmc.o +obj-$(CONFIG_MACH_ENCORE) += board-omap3encore.o \ + hsmmc.o obj-$(CONFIG_MACH_OVERO) += board-overo.o \ hsmmc.o obj-$(CONFIG_MACH_OMAP3EVM) += board-omap3evm.o \ diff --git a/arch/arm/mach-omap2/board-omap3encore.c b/arch/arm/mach-omap2/board-omap3encore.c new file mode 100644 index 0000000..c7bf8de --- /dev/null +++ b/arch/arm/mach-omap2/board-omap3encore.c @@ -0,0 +1,380 @@ +/* + * + * Copyright (C) 2008 Texas Instruments Inc. + * Vikram Pandita <vikram.pandita@ti.com> + * + * Modified from mach-omap2/board-ldp.c + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * April 2011 Oleg Drokin <green@linuxhacker.ru> - Port to 2.6.39 + * + */ + +#include <linux/kernel.h> +#include <linux/platform_device.h> +#include <linux/gpio_keys.h> +#include <linux/err.h> + +#include <linux/spi/spi.h> +#include <linux/i2c/twl.h> +#include <linux/regulator/machine.h> +#include <linux/regulator/fixed.h> +#include <mach/hardware.h> +#include <asm/mach-types.h> +#include <asm/mach/arch.h> + +#include <mach/gpio.h> +#include <plat/board.h> +#include <plat/common.h> +#include <plat/usb.h> +#include <plat/mux.h> +#include <plat/sram.h> +#include <plat/mmc.h> +#include <plat/omap-serial.h> +#include <plat/system.h> + +#include "mux.h" +#include "hsmmc.h" +#include "sdram-hynix-h8mbx00u0mer-0em.h" + +/* Encore-specific device-info and i2c addresses. */ +/* Battery, bus 1 */ +#define MAX17042_I2C_SLAVE_ADDRESS 0x36 +#define MAX17042_GPIO_FOR_IRQ 100 + +/*addition of MAXIM8903/TI GPIO mapping WRT schematics */ +#define MAX8903_UOK_GPIO_FOR_IRQ 115 +#define MAX8903_DOK_GPIO_FOR_IRQ 114 +#define MAX8903_GPIO_CHG_EN 110 +#define MAX8903_GPIO_CHG_STATUS 111 +#define MAX8903_GPIO_CHG_FLT 101 +#define MAX8903_GPIO_CHG_IUSB 102 +#define MAX8903_GPIO_CHG_USUS 104 +#define MAX8903_GPIO_CHG_ILM 61 + +/* TI WLAN */ +#define ENCORE_WIFI_PMENA_GPIO 22 +#define ENCORE_WIFI_IRQ_GPIO 15 +#define ENCORE_WIFI_EN_POW 16 + +/* Accelerometer i2c bus 1*/ +#define KXTF9_I2C_SLAVE_ADDRESS 0x0F +#define KXTF9_GPIO_FOR_PWR 34 +#define KXTF9_GPIO_FOR_IRQ 113 + +/* Touch screen i2c bus 2*/ +#define CYTTSP_I2C_SLAVEADDRESS 34 +#define ENCORE_CYTTSP_GPIO 99 +#define ENCORE_CYTTSP_RESET_GPIO 46 + +/* Audio codec, i2c bus 2 */ +#define AUDIO_CODEC_POWER_ENABLE_GPIO 103 +#define AUDIO_CODEC_RESET_GPIO 37 +#define AUDIO_CODEC_IRQ_GPIO 59 +#define AIC3100_I2CSLAVEADDRESS 0x18 + + +/* Different HW revisions */ +#define BOARD_ENCORE_REV_EVT1A 0x1 +#define BOARD_ENCORE_REV_EVT1B 0x2 +#define BOARD_ENCORE_REV_EVT2 0x3 +#define BOARD_ENCORE_REV_DVT 0x4 +#define BOARD_ENCORE_REV_PVT 0x5 +#define BOARD_ENCORE_REV_UNKNOWN 0x6 + +static inline int is_encore_board_evt2(void) +{ + return (system_rev >= BOARD_ENCORE_REV_EVT2); +} + +static inline int is_encore_board_evt1b(void) +{ + return (system_rev == BOARD_ENCORE_REV_EVT1B); +} + +static int encore_twl4030_keymap[] = { + KEY(0, 0, KEY_HOME), + KEY(0, 1, KEY_VOLUMEUP), + KEY(0, 2, KEY_VOLUMEDOWN), + 0 +}; + +static struct matrix_keymap_data encore_twl4030_keymap_data = { + .keymap = encore_twl4030_keymap, + .keymap_size = ARRAY_SIZE(encore_twl4030_keymap), +}; + +static struct twl4030_keypad_data encore_kp_twl4030_data = { + .rows = 8, + .cols = 8, + .keymap_data = &encore_twl4030_keymap_data, + .rep = 1, +}; + +/* HOME key code for HW > EVT2A */ +static struct gpio_keys_button encore_gpio_buttons[] = { + { + .code = KEY_POWER, + .gpio = 14, + .desc = "POWER", + .active_low = 0, + .wakeup = 1, + }, + { + .code = KEY_HOME, + .gpio = 48, + .desc = "HOME", + .active_low = 1, + .wakeup = 1, + }, +}; + +static struct gpio_keys_platform_data encore_gpio_key_info = { + .buttons = encore_gpio_buttons, + .nbuttons = ARRAY_SIZE(encore_gpio_buttons), +}; + +static struct platform_device encore_keys_gpio = { + .name = "gpio-keys", + .id = -1, + .dev = { + .platform_data = &encore_gpio_key_info, + }, +}; + +static struct platform_device *encore_devices[] __initdata = { + &encore_keys_gpio, +}; + +static void __init omap_encore_init_early(void) +{ + omap2_init_common_infrastructure(); + omap2_init_common_devices(h8mbx00u0mer0em_sdrc_params, + h8mbx00u0mer0em_sdrc_params); +} + +static struct twl4030_usb_data encore_usb_data = { + .usb_mode = T2_USB_MODE_ULPI, +}; + +static struct regulator_consumer_supply encore_vmmc1_supply = { + .supply = "vmmc", +}; + +static struct regulator_consumer_supply encore_vdda_dac_supply = + REGULATOR_SUPPLY("vdda_dac", "omapdss_venc"); + +/* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */ +static struct regulator_init_data encore_vmmc1 = { + .constraints = { + .min_uV = 1850000, + .max_uV = 3150000, + .valid_modes_mask = REGULATOR_MODE_NORMAL + | REGULATOR_MODE_STANDBY, + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE + | REGULATOR_CHANGE_MODE + | REGULATOR_CHANGE_STATUS, + }, + .num_consumer_supplies = 1, + .consumer_supplies = &encore_vmmc1_supply, +}; + +static struct regulator_init_data encore_vdac = { + .constraints = { + .min_uV = 1800000, + .max_uV = 1800000, + .valid_modes_mask = REGULATOR_MODE_NORMAL + | REGULATOR_MODE_STANDBY, + .valid_ops_mask = REGULATOR_CHANGE_MODE + | REGULATOR_CHANGE_STATUS, + }, + .num_consumer_supplies = 1, + .consumer_supplies = &encore_vdda_dac_supply, +}; + +/* The order is reverted in this table so that internal eMMC is presented + * as first mmc card for compatibility with existing installations and + * for common sense reasons */ +static struct omap2_hsmmc_info mmc[] __initdata = { + { + .name = "internal", + .mmc = 2, + .caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA, + .gpio_cd = -EINVAL, + .gpio_wp = -EINVAL, + .nonremovable = true, + .power_saving = true, + .ocr_mask = MMC_VDD_165_195, /* 1.85V */ + }, + { + .name = "external", + .mmc = 1, + .caps = MMC_CAP_4_BIT_DATA, + .gpio_cd = -EINVAL, + .gpio_wp = -EINVAL, + .power_saving = true, + }, + { + .name = "internal", + .mmc = 3, + .caps = MMC_CAP_4_BIT_DATA, + .gpio_cd = -EINVAL, + .gpio_wp = -EINVAL, + .nonremovable = true, + .power_saving = true, + }, + {} /* Terminator */ +}; + +static int encore_hsmmc_card_detect(struct device *dev, int slot) +{ + struct omap_mmc_platform_data *mmc = dev->platform_data; + + /* Encore board EVT2 and later has pin high when card is present) */ + return gpio_get_value_cansleep(mmc->slots[0].switch_pin); +} + +static int encore_twl4030_hsmmc_late_init(struct device *dev) +{ + int ret = 0; + struct platform_device *pdev = container_of(dev, + struct platform_device, dev); + struct omap_mmc_platform_data *pdata = dev->platform_data; + + if(is_encore_board_evt2()) { + /* Setting MMC1 (external) Card detect */ + if (pdev->id == 0) { + pdata->slots[0].card_detect = encore_hsmmc_card_detect; + } + } + return ret; +} + +static __init void encore_hsmmc_set_late_init(struct device *dev) +{ + struct omap_mmc_platform_data *pdata; + + /* dev can be null if CONFIG_MMC_OMAP_HS is not set */ + if (!dev) + return; + + pdata = dev->platform_data; + pdata->init = encore_twl4030_hsmmc_late_init; +} + +static int __ref encore_twl_gpio_setup(struct device *dev, + unsigned gpio, unsigned ngpio) +{ + struct omap2_hsmmc_info *c; + /* + * gpio + 0 is "mmc0_cd" (input/IRQ), + * gpio + 1 is "mmc1_cd" (input/IRQ) + */ + mmc[1].gpio_cd = gpio + 0; + mmc[0].gpio_cd = gpio + 1; + omap2_hsmmc_init(mmc); + for (c = mmc; c->mmc; c++) + encore_hsmmc_set_late_init(c->dev); + + /* + * link regulators to MMC adapters ... we "know" the + * regulators will be set up only *after* we return. + */ + encore_vmmc1_supply.dev = mmc[1].dev; + + return 0; +} + +static struct twl4030_gpio_platform_data encore_gpio_data = { + .gpio_base = OMAP_MAX_GPIO_LINES, + .irq_base = TWL4030_GPIO_IRQ_BASE, + .irq_end = TWL4030_GPIO_IRQ_END, + .setup = encore_twl_gpio_setup, +}; + +static struct twl4030_madc_platform_data encore_madc_data = { + .irq_line = 1, +}; + +static struct twl4030_platform_data __refdata encore_twldata = { + .irq_base = TWL4030_IRQ_BASE, + .irq_end = TWL4030_IRQ_END, + + .madc = &encore_madc_data, + .usb = &encore_usb_data, + .gpio = &encore_gpio_data, + .keypad = &encore_kp_twl4030_data, + .vmmc1 = &encore_vmmc1, + .vdac = &encore_vdac, +}; + +static struct i2c_board_info __initdata encore_i2c_bus1_info[] = { + { + I2C_BOARD_INFO("tps65921", 0x48), + .flags = I2C_CLIENT_WAKE, + .irq = INT_34XX_SYS_NIRQ, + .platform_data = &encore_twldata, + }, +}; + +static struct i2c_board_info __initdata encore_i2c_bus2_info[] = { +}; + + +static struct omap_musb_board_data musb_board_data = { + .interface_type = MUSB_INTERFACE_ULPI, +#ifdef CONFIG_USB_MUSB_OTG + .mode = MUSB_OTG, +#elif defined(CONFIG_USB_MUSB_HDRC_HCD) + .mode = MUSB_HOST, +#elif defined(CONFIG_USB_GADGET_MUSB_HDRC) + .mode = MUSB_PERIPHERAL, +#endif + .power = 100, +}; + +#ifdef CONFIG_OMAP_MUX +static struct omap_board_mux board_mux[] __initdata = { + { .reg_offset = OMAP_MUX_TERMINATOR }, +}; +#else +#define board_mux NULL +#endif + +static struct omap_board_config_kernel encore_config[] __initdata = { +}; + +static int __init omap_i2c_init(void) +{ + omap_register_i2c_bus(1, 100, encore_i2c_bus1_info, + ARRAY_SIZE(encore_i2c_bus1_info)); + omap_register_i2c_bus(2, 400, encore_i2c_bus2_info, + ARRAY_SIZE(encore_i2c_bus2_info)); + return 0; +} + +static void __init omap_encore_init(void) +{ + omap3_mux_init(board_mux, OMAP_PACKAGE_CBB); + omap_i2c_init(); + omap_serial_init(); + usb_musb_init(&musb_board_data); + + omap_board_config = encore_config; + omap_board_config_size = ARRAY_SIZE(encore_config); + + platform_add_devices(encore_devices, ARRAY_SIZE(encore_devices)); +} + +MACHINE_START(ENCORE, "encore") + .boot_params = 0x80000100, + .reserve = omap_reserve, + .map_io = omap3_map_io, + .init_early = omap_encore_init_early, + .init_irq = omap_init_irq, + .init_machine = omap_encore_init, + .timer = &omap_timer, +MACHINE_END diff --git a/arch/arm/plat-omap/include/plat/uncompress.h b/arch/arm/plat-omap/include/plat/uncompress.h index 30b891c..f2de4ff 100644 --- a/arch/arm/plat-omap/include/plat/uncompress.h +++ b/arch/arm/plat-omap/include/plat/uncompress.h @@ -161,6 +161,7 @@ static inline void __arch_decomp_setup(unsigned long arch_id) DEBUG_LL_OMAP3(3, omap_ldp); DEBUG_LL_OMAP3(3, overo); DEBUG_LL_OMAP3(3, touchbook); + DEBUG_LL_OMAP3(3, encore); /* omap4 based boards using UART3 */ DEBUG_LL_OMAP4(3, omap_4430sdp); diff --git a/arch/arm/tools/mach-types b/arch/arm/tools/mach-types index 7ca41f0..2f0db3e 100644 --- a/arch/arm/tools/mach-types +++ b/arch/arm/tools/mach-types @@ -962,7 +962,7 @@ omapl138_case_a3 MACH_OMAPL138_CASE_A3 OMAPL138_CASE_A3 3280 uemd MACH_UEMD UEMD 3281 ccwmx51mut MACH_CCWMX51MUT CCWMX51MUT 3282 rockhopper MACH_ROCKHOPPER ROCKHOPPER 3283 -nookcolor MACH_NOOKCOLOR NOOKCOLOR 3284 +encore MACH_ENCORE ENCORE 3284 hkdkc100 MACH_HKDKC100 HKDKC100 3285 ts42xx MACH_TS42XX TS42XX 3286 aebl MACH_AEBL AEBL 3287 -- 1.7.4.4 ^ permalink raw reply related [flat|nested] 9+ messages in thread
* Re: [PATCH 1/2] Initial B&N Nook Color (encore) support. 2011-04-28 15:57 ` [PATCH 1/2] Initial B&N Nook Color (encore) support green @ 2011-04-28 23:34 ` Abimanyu Gottumukkala 2011-04-29 0:49 ` Oleg Drokin 2011-05-03 9:22 ` Tony Lindgren 1 sibling, 1 reply; 9+ messages in thread From: Abimanyu Gottumukkala @ 2011-04-28 23:34 UTC (permalink / raw) To: green; +Cc: linux-omap Hi, Nook color has Ti OMAP 3621. 3621 CPU Support is not available in current kernel, adding CPU support will be nice before board. BN is set to release new source code in few days, taking new code as porting base is also recommended. Regards, Abimanyu G On Thu, Apr 28, 2011 at 9:27 PM, <green@linuxhacker.ru> wrote: > From: Oleg Drokin <green@linuxhacker.ru> > > Bare-bones board file, comes with serial console, gpio keys, > MMC/SDCard and USB support. > --- > arch/arm/mach-omap2/Kconfig | 5 + > arch/arm/mach-omap2/Makefile | 2 + > arch/arm/mach-omap2/board-omap3encore.c | 380 ++++++++++++++++++++++++++ > arch/arm/plat-omap/include/plat/uncompress.h | 1 + > arch/arm/tools/mach-types | 2 +- > 5 files changed, 389 insertions(+), 1 deletions(-) > create mode 100644 arch/arm/mach-omap2/board-omap3encore.c > > diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig > index b997a35..5370561 100644 > --- a/arch/arm/mach-omap2/Kconfig > +++ b/arch/arm/mach-omap2/Kconfig > @@ -173,6 +173,11 @@ config MACH_OMAP3_TORPEDO > for full description please see the products webpage at > http://www.logicpd.com/products/development-kits/zoom-omap35x-torpedo-development-kit > > +config MACH_ENCORE > + bool "Barnes & Noble Encore (Nook Color)" > + depends on ARCH_OMAP3 > + select OMAP_PACKAGE_CBP > + > config MACH_OVERO > bool "Gumstix Overo board" > depends on ARCH_OMAP3 > diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile > index 512b152..b894777 100644 > --- a/arch/arm/mach-omap2/Makefile > +++ b/arch/arm/mach-omap2/Makefile > @@ -189,6 +189,8 @@ obj-$(CONFIG_MACH_OMAP3530_LV_SOM) += board-omap3logic.o \ > hsmmc.o > obj-$(CONFIG_MACH_OMAP3_TORPEDO) += board-omap3logic.o \ > hsmmc.o > +obj-$(CONFIG_MACH_ENCORE) += board-omap3encore.o \ > + hsmmc.o > obj-$(CONFIG_MACH_OVERO) += board-overo.o \ > hsmmc.o > obj-$(CONFIG_MACH_OMAP3EVM) += board-omap3evm.o \ > diff --git a/arch/arm/mach-omap2/board-omap3encore.c b/arch/arm/mach-omap2/board-omap3encore.c > new file mode 100644 > index 0000000..c7bf8de > --- /dev/null > +++ b/arch/arm/mach-omap2/board-omap3encore.c > @@ -0,0 +1,380 @@ > +/* > + * > + * Copyright (C) 2008 Texas Instruments Inc. > + * Vikram Pandita <vikram.pandita@ti.com> > + * > + * Modified from mach-omap2/board-ldp.c > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + * > + * April 2011 Oleg Drokin <green@linuxhacker.ru> - Port to 2.6.39 > + * > + */ > + > +#include <linux/kernel.h> > +#include <linux/platform_device.h> > +#include <linux/gpio_keys.h> > +#include <linux/err.h> > + > +#include <linux/spi/spi.h> > +#include <linux/i2c/twl.h> > +#include <linux/regulator/machine.h> > +#include <linux/regulator/fixed.h> > +#include <mach/hardware.h> > +#include <asm/mach-types.h> > +#include <asm/mach/arch.h> > + > +#include <mach/gpio.h> > +#include <plat/board.h> > +#include <plat/common.h> > +#include <plat/usb.h> > +#include <plat/mux.h> > +#include <plat/sram.h> > +#include <plat/mmc.h> > +#include <plat/omap-serial.h> > +#include <plat/system.h> > + > +#include "mux.h" > +#include "hsmmc.h" > +#include "sdram-hynix-h8mbx00u0mer-0em.h" > + > +/* Encore-specific device-info and i2c addresses. */ > +/* Battery, bus 1 */ > +#define MAX17042_I2C_SLAVE_ADDRESS 0x36 > +#define MAX17042_GPIO_FOR_IRQ 100 > + > +/*addition of MAXIM8903/TI GPIO mapping WRT schematics */ > +#define MAX8903_UOK_GPIO_FOR_IRQ 115 > +#define MAX8903_DOK_GPIO_FOR_IRQ 114 > +#define MAX8903_GPIO_CHG_EN 110 > +#define MAX8903_GPIO_CHG_STATUS 111 > +#define MAX8903_GPIO_CHG_FLT 101 > +#define MAX8903_GPIO_CHG_IUSB 102 > +#define MAX8903_GPIO_CHG_USUS 104 > +#define MAX8903_GPIO_CHG_ILM 61 > + > +/* TI WLAN */ > +#define ENCORE_WIFI_PMENA_GPIO 22 > +#define ENCORE_WIFI_IRQ_GPIO 15 > +#define ENCORE_WIFI_EN_POW 16 > + > +/* Accelerometer i2c bus 1*/ > +#define KXTF9_I2C_SLAVE_ADDRESS 0x0F > +#define KXTF9_GPIO_FOR_PWR 34 > +#define KXTF9_GPIO_FOR_IRQ 113 > + > +/* Touch screen i2c bus 2*/ > +#define CYTTSP_I2C_SLAVEADDRESS 34 > +#define ENCORE_CYTTSP_GPIO 99 > +#define ENCORE_CYTTSP_RESET_GPIO 46 > + > +/* Audio codec, i2c bus 2 */ > +#define AUDIO_CODEC_POWER_ENABLE_GPIO 103 > +#define AUDIO_CODEC_RESET_GPIO 37 > +#define AUDIO_CODEC_IRQ_GPIO 59 > +#define AIC3100_I2CSLAVEADDRESS 0x18 > + > + > +/* Different HW revisions */ > +#define BOARD_ENCORE_REV_EVT1A 0x1 > +#define BOARD_ENCORE_REV_EVT1B 0x2 > +#define BOARD_ENCORE_REV_EVT2 0x3 > +#define BOARD_ENCORE_REV_DVT 0x4 > +#define BOARD_ENCORE_REV_PVT 0x5 > +#define BOARD_ENCORE_REV_UNKNOWN 0x6 > + > +static inline int is_encore_board_evt2(void) > +{ > + return (system_rev >= BOARD_ENCORE_REV_EVT2); > +} > + > +static inline int is_encore_board_evt1b(void) > +{ > + return (system_rev == BOARD_ENCORE_REV_EVT1B); > +} > + > +static int encore_twl4030_keymap[] = { > + KEY(0, 0, KEY_HOME), > + KEY(0, 1, KEY_VOLUMEUP), > + KEY(0, 2, KEY_VOLUMEDOWN), > + 0 > +}; > + > +static struct matrix_keymap_data encore_twl4030_keymap_data = { > + .keymap = encore_twl4030_keymap, > + .keymap_size = ARRAY_SIZE(encore_twl4030_keymap), > +}; > + > +static struct twl4030_keypad_data encore_kp_twl4030_data = { > + .rows = 8, > + .cols = 8, > + .keymap_data = &encore_twl4030_keymap_data, > + .rep = 1, > +}; > + > +/* HOME key code for HW > EVT2A */ > +static struct gpio_keys_button encore_gpio_buttons[] = { > + { > + .code = KEY_POWER, > + .gpio = 14, > + .desc = "POWER", > + .active_low = 0, > + .wakeup = 1, > + }, > + { > + .code = KEY_HOME, > + .gpio = 48, > + .desc = "HOME", > + .active_low = 1, > + .wakeup = 1, > + }, > +}; > + > +static struct gpio_keys_platform_data encore_gpio_key_info = { > + .buttons = encore_gpio_buttons, > + .nbuttons = ARRAY_SIZE(encore_gpio_buttons), > +}; > + > +static struct platform_device encore_keys_gpio = { > + .name = "gpio-keys", > + .id = -1, > + .dev = { > + .platform_data = &encore_gpio_key_info, > + }, > +}; > + > +static struct platform_device *encore_devices[] __initdata = { > + &encore_keys_gpio, > +}; > + > +static void __init omap_encore_init_early(void) > +{ > + omap2_init_common_infrastructure(); > + omap2_init_common_devices(h8mbx00u0mer0em_sdrc_params, > + h8mbx00u0mer0em_sdrc_params); > +} > + > +static struct twl4030_usb_data encore_usb_data = { > + .usb_mode = T2_USB_MODE_ULPI, > +}; > + > +static struct regulator_consumer_supply encore_vmmc1_supply = { > + .supply = "vmmc", > +}; > + > +static struct regulator_consumer_supply encore_vdda_dac_supply = > + REGULATOR_SUPPLY("vdda_dac", "omapdss_venc"); > + > +/* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */ > +static struct regulator_init_data encore_vmmc1 = { > + .constraints = { > + .min_uV = 1850000, > + .max_uV = 3150000, > + .valid_modes_mask = REGULATOR_MODE_NORMAL > + | REGULATOR_MODE_STANDBY, > + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE > + | REGULATOR_CHANGE_MODE > + | REGULATOR_CHANGE_STATUS, > + }, > + .num_consumer_supplies = 1, > + .consumer_supplies = &encore_vmmc1_supply, > +}; > + > +static struct regulator_init_data encore_vdac = { > + .constraints = { > + .min_uV = 1800000, > + .max_uV = 1800000, > + .valid_modes_mask = REGULATOR_MODE_NORMAL > + | REGULATOR_MODE_STANDBY, > + .valid_ops_mask = REGULATOR_CHANGE_MODE > + | REGULATOR_CHANGE_STATUS, > + }, > + .num_consumer_supplies = 1, > + .consumer_supplies = &encore_vdda_dac_supply, > +}; > + > +/* The order is reverted in this table so that internal eMMC is presented > + * as first mmc card for compatibility with existing installations and > + * for common sense reasons */ > +static struct omap2_hsmmc_info mmc[] __initdata = { > + { > + .name = "internal", > + .mmc = 2, > + .caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA, > + .gpio_cd = -EINVAL, > + .gpio_wp = -EINVAL, > + .nonremovable = true, > + .power_saving = true, > + .ocr_mask = MMC_VDD_165_195, /* 1.85V */ > + }, > + { > + .name = "external", > + .mmc = 1, > + .caps = MMC_CAP_4_BIT_DATA, > + .gpio_cd = -EINVAL, > + .gpio_wp = -EINVAL, > + .power_saving = true, > + }, > + { > + .name = "internal", > + .mmc = 3, > + .caps = MMC_CAP_4_BIT_DATA, > + .gpio_cd = -EINVAL, > + .gpio_wp = -EINVAL, > + .nonremovable = true, > + .power_saving = true, > + }, > + {} /* Terminator */ > +}; > + > +static int encore_hsmmc_card_detect(struct device *dev, int slot) > +{ > + struct omap_mmc_platform_data *mmc = dev->platform_data; > + > + /* Encore board EVT2 and later has pin high when card is present) */ > + return gpio_get_value_cansleep(mmc->slots[0].switch_pin); > +} > + > +static int encore_twl4030_hsmmc_late_init(struct device *dev) > +{ > + int ret = 0; > + struct platform_device *pdev = container_of(dev, > + struct platform_device, dev); > + struct omap_mmc_platform_data *pdata = dev->platform_data; > + > + if(is_encore_board_evt2()) { > + /* Setting MMC1 (external) Card detect */ > + if (pdev->id == 0) { > + pdata->slots[0].card_detect = encore_hsmmc_card_detect; > + } > + } > + return ret; > +} > + > +static __init void encore_hsmmc_set_late_init(struct device *dev) > +{ > + struct omap_mmc_platform_data *pdata; > + > + /* dev can be null if CONFIG_MMC_OMAP_HS is not set */ > + if (!dev) > + return; > + > + pdata = dev->platform_data; > + pdata->init = encore_twl4030_hsmmc_late_init; > +} > + > +static int __ref encore_twl_gpio_setup(struct device *dev, > + unsigned gpio, unsigned ngpio) > +{ > + struct omap2_hsmmc_info *c; > + /* > + * gpio + 0 is "mmc0_cd" (input/IRQ), > + * gpio + 1 is "mmc1_cd" (input/IRQ) > + */ > + mmc[1].gpio_cd = gpio + 0; > + mmc[0].gpio_cd = gpio + 1; > + omap2_hsmmc_init(mmc); > + for (c = mmc; c->mmc; c++) > + encore_hsmmc_set_late_init(c->dev); > + > + /* > + * link regulators to MMC adapters ... we "know" the > + * regulators will be set up only *after* we return. > + */ > + encore_vmmc1_supply.dev = mmc[1].dev; > + > + return 0; > +} > + > +static struct twl4030_gpio_platform_data encore_gpio_data = { > + .gpio_base = OMAP_MAX_GPIO_LINES, > + .irq_base = TWL4030_GPIO_IRQ_BASE, > + .irq_end = TWL4030_GPIO_IRQ_END, > + .setup = encore_twl_gpio_setup, > +}; > + > +static struct twl4030_madc_platform_data encore_madc_data = { > + .irq_line = 1, > +}; > + > +static struct twl4030_platform_data __refdata encore_twldata = { > + .irq_base = TWL4030_IRQ_BASE, > + .irq_end = TWL4030_IRQ_END, > + > + .madc = &encore_madc_data, > + .usb = &encore_usb_data, > + .gpio = &encore_gpio_data, > + .keypad = &encore_kp_twl4030_data, > + .vmmc1 = &encore_vmmc1, > + .vdac = &encore_vdac, > +}; > + > +static struct i2c_board_info __initdata encore_i2c_bus1_info[] = { > + { > + I2C_BOARD_INFO("tps65921", 0x48), > + .flags = I2C_CLIENT_WAKE, > + .irq = INT_34XX_SYS_NIRQ, > + .platform_data = &encore_twldata, > + }, > +}; > + > +static struct i2c_board_info __initdata encore_i2c_bus2_info[] = { > +}; > + > + > +static struct omap_musb_board_data musb_board_data = { > + .interface_type = MUSB_INTERFACE_ULPI, > +#ifdef CONFIG_USB_MUSB_OTG > + .mode = MUSB_OTG, > +#elif defined(CONFIG_USB_MUSB_HDRC_HCD) > + .mode = MUSB_HOST, > +#elif defined(CONFIG_USB_GADGET_MUSB_HDRC) > + .mode = MUSB_PERIPHERAL, > +#endif > + .power = 100, > +}; > + > +#ifdef CONFIG_OMAP_MUX > +static struct omap_board_mux board_mux[] __initdata = { > + { .reg_offset = OMAP_MUX_TERMINATOR }, > +}; > +#else > +#define board_mux NULL > +#endif > + > +static struct omap_board_config_kernel encore_config[] __initdata = { > +}; > + > +static int __init omap_i2c_init(void) > +{ > + omap_register_i2c_bus(1, 100, encore_i2c_bus1_info, > + ARRAY_SIZE(encore_i2c_bus1_info)); > + omap_register_i2c_bus(2, 400, encore_i2c_bus2_info, > + ARRAY_SIZE(encore_i2c_bus2_info)); > + return 0; > +} > + > +static void __init omap_encore_init(void) > +{ > + omap3_mux_init(board_mux, OMAP_PACKAGE_CBB); > + omap_i2c_init(); > + omap_serial_init(); > + usb_musb_init(&musb_board_data); > + > + omap_board_config = encore_config; > + omap_board_config_size = ARRAY_SIZE(encore_config); > + > + platform_add_devices(encore_devices, ARRAY_SIZE(encore_devices)); > +} > + > +MACHINE_START(ENCORE, "encore") > + .boot_params = 0x80000100, > + .reserve = omap_reserve, > + .map_io = omap3_map_io, > + .init_early = omap_encore_init_early, > + .init_irq = omap_init_irq, > + .init_machine = omap_encore_init, > + .timer = &omap_timer, > +MACHINE_END > diff --git a/arch/arm/plat-omap/include/plat/uncompress.h b/arch/arm/plat-omap/include/plat/uncompress.h > index 30b891c..f2de4ff 100644 > --- a/arch/arm/plat-omap/include/plat/uncompress.h > +++ b/arch/arm/plat-omap/include/plat/uncompress.h > @@ -161,6 +161,7 @@ static inline void __arch_decomp_setup(unsigned long arch_id) > DEBUG_LL_OMAP3(3, omap_ldp); > DEBUG_LL_OMAP3(3, overo); > DEBUG_LL_OMAP3(3, touchbook); > + DEBUG_LL_OMAP3(3, encore); > > /* omap4 based boards using UART3 */ > DEBUG_LL_OMAP4(3, omap_4430sdp); > diff --git a/arch/arm/tools/mach-types b/arch/arm/tools/mach-types > index 7ca41f0..2f0db3e 100644 > --- a/arch/arm/tools/mach-types > +++ b/arch/arm/tools/mach-types > @@ -962,7 +962,7 @@ omapl138_case_a3 MACH_OMAPL138_CASE_A3 OMAPL138_CASE_A3 3280 > uemd MACH_UEMD UEMD 3281 > ccwmx51mut MACH_CCWMX51MUT CCWMX51MUT 3282 > rockhopper MACH_ROCKHOPPER ROCKHOPPER 3283 > -nookcolor MACH_NOOKCOLOR NOOKCOLOR 3284 > +encore MACH_ENCORE ENCORE 3284 > hkdkc100 MACH_HKDKC100 HKDKC100 3285 > ts42xx MACH_TS42XX TS42XX 3286 > aebl MACH_AEBL AEBL 3287 > -- > 1.7.4.4 > > -- > To unsubscribe from this list: send the line "unsubscribe linux-omap" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html > -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH 1/2] Initial B&N Nook Color (encore) support. 2011-04-28 23:34 ` Abimanyu Gottumukkala @ 2011-04-29 0:49 ` Oleg Drokin 2011-05-03 11:08 ` Vladimir Pantelic 0 siblings, 1 reply; 9+ messages in thread From: Oleg Drokin @ 2011-04-29 0:49 UTC (permalink / raw) To: Abimanyu Gottumukkala; +Cc: linux-omap Hello! Is there any special support needed for 3621, though? My understanding is that's just 3630 without a "phone" part? The .29 kernel they had only added is_omap3621 stuff that's not called anywhere, but smartreflex code (I guess that's might be useful to add too of course). I know about the new code drop is coming, but I don't expect there to be any basic stuff changes (and this board file is coming pretty barebones right now), besides I am not so optimistic to actually expect this patch to be merged right away, but I am already gathering valuable feedback. ;) BTW I saw in the archives that you are also working a port, do you have your tree hosted anywhere? Bye, Oleg On Apr 28, 2011, at 7:34 PM, Abimanyu Gottumukkala wrote: > Hi, > > Nook color has Ti OMAP 3621. 3621 CPU Support is not available in > current kernel, adding CPU support will be nice before board. > BN is set to release new source code in few days, taking new code as > porting base is also recommended. > > Regards, > Abimanyu G > > On Thu, Apr 28, 2011 at 9:27 PM, <green@linuxhacker.ru> wrote: >> From: Oleg Drokin <green@linuxhacker.ru> >> >> Bare-bones board file, comes with serial console, gpio keys, >> MMC/SDCard and USB support. >> --- >> arch/arm/mach-omap2/Kconfig | 5 + >> arch/arm/mach-omap2/Makefile | 2 + >> arch/arm/mach-omap2/board-omap3encore.c | 380 ++++++++++++++++++++++++++ >> arch/arm/plat-omap/include/plat/uncompress.h | 1 + >> arch/arm/tools/mach-types | 2 +- >> 5 files changed, 389 insertions(+), 1 deletions(-) >> create mode 100644 arch/arm/mach-omap2/board-omap3encore.c >> >> diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig >> index b997a35..5370561 100644 >> --- a/arch/arm/mach-omap2/Kconfig >> +++ b/arch/arm/mach-omap2/Kconfig >> @@ -173,6 +173,11 @@ config MACH_OMAP3_TORPEDO >> for full description please see the products webpage at >> http://www.logicpd.com/products/development-kits/zoom-omap35x-torpedo-development-kit >> >> +config MACH_ENCORE >> + bool "Barnes & Noble Encore (Nook Color)" >> + depends on ARCH_OMAP3 >> + select OMAP_PACKAGE_CBP >> + >> config MACH_OVERO >> bool "Gumstix Overo board" >> depends on ARCH_OMAP3 >> diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile >> index 512b152..b894777 100644 >> --- a/arch/arm/mach-omap2/Makefile >> +++ b/arch/arm/mach-omap2/Makefile >> @@ -189,6 +189,8 @@ obj-$(CONFIG_MACH_OMAP3530_LV_SOM) += board-omap3logic.o \ >> hsmmc.o >> obj-$(CONFIG_MACH_OMAP3_TORPEDO) += board-omap3logic.o \ >> hsmmc.o >> +obj-$(CONFIG_MACH_ENCORE) += board-omap3encore.o \ >> + hsmmc.o >> obj-$(CONFIG_MACH_OVERO) += board-overo.o \ >> hsmmc.o >> obj-$(CONFIG_MACH_OMAP3EVM) += board-omap3evm.o \ >> diff --git a/arch/arm/mach-omap2/board-omap3encore.c b/arch/arm/mach-omap2/board-omap3encore.c >> new file mode 100644 >> index 0000000..c7bf8de >> --- /dev/null >> +++ b/arch/arm/mach-omap2/board-omap3encore.c >> @@ -0,0 +1,380 @@ >> +/* >> + * >> + * Copyright (C) 2008 Texas Instruments Inc. >> + * Vikram Pandita <vikram.pandita@ti.com> >> + * >> + * Modified from mach-omap2/board-ldp.c >> + * >> + * This program is free software; you can redistribute it and/or modify >> + * it under the terms of the GNU General Public License version 2 as >> + * published by the Free Software Foundation. >> + * >> + * April 2011 Oleg Drokin <green@linuxhacker.ru> - Port to 2.6.39 >> + * >> + */ >> + >> +#include <linux/kernel.h> >> +#include <linux/platform_device.h> >> +#include <linux/gpio_keys.h> >> +#include <linux/err.h> >> + >> +#include <linux/spi/spi.h> >> +#include <linux/i2c/twl.h> >> +#include <linux/regulator/machine.h> >> +#include <linux/regulator/fixed.h> >> +#include <mach/hardware.h> >> +#include <asm/mach-types.h> >> +#include <asm/mach/arch.h> >> + >> +#include <mach/gpio.h> >> +#include <plat/board.h> >> +#include <plat/common.h> >> +#include <plat/usb.h> >> +#include <plat/mux.h> >> +#include <plat/sram.h> >> +#include <plat/mmc.h> >> +#include <plat/omap-serial.h> >> +#include <plat/system.h> >> + >> +#include "mux.h" >> +#include "hsmmc.h" >> +#include "sdram-hynix-h8mbx00u0mer-0em.h" >> + >> +/* Encore-specific device-info and i2c addresses. */ >> +/* Battery, bus 1 */ >> +#define MAX17042_I2C_SLAVE_ADDRESS 0x36 >> +#define MAX17042_GPIO_FOR_IRQ 100 >> + >> +/*addition of MAXIM8903/TI GPIO mapping WRT schematics */ >> +#define MAX8903_UOK_GPIO_FOR_IRQ 115 >> +#define MAX8903_DOK_GPIO_FOR_IRQ 114 >> +#define MAX8903_GPIO_CHG_EN 110 >> +#define MAX8903_GPIO_CHG_STATUS 111 >> +#define MAX8903_GPIO_CHG_FLT 101 >> +#define MAX8903_GPIO_CHG_IUSB 102 >> +#define MAX8903_GPIO_CHG_USUS 104 >> +#define MAX8903_GPIO_CHG_ILM 61 >> + >> +/* TI WLAN */ >> +#define ENCORE_WIFI_PMENA_GPIO 22 >> +#define ENCORE_WIFI_IRQ_GPIO 15 >> +#define ENCORE_WIFI_EN_POW 16 >> + >> +/* Accelerometer i2c bus 1*/ >> +#define KXTF9_I2C_SLAVE_ADDRESS 0x0F >> +#define KXTF9_GPIO_FOR_PWR 34 >> +#define KXTF9_GPIO_FOR_IRQ 113 >> + >> +/* Touch screen i2c bus 2*/ >> +#define CYTTSP_I2C_SLAVEADDRESS 34 >> +#define ENCORE_CYTTSP_GPIO 99 >> +#define ENCORE_CYTTSP_RESET_GPIO 46 >> + >> +/* Audio codec, i2c bus 2 */ >> +#define AUDIO_CODEC_POWER_ENABLE_GPIO 103 >> +#define AUDIO_CODEC_RESET_GPIO 37 >> +#define AUDIO_CODEC_IRQ_GPIO 59 >> +#define AIC3100_I2CSLAVEADDRESS 0x18 >> + >> + >> +/* Different HW revisions */ >> +#define BOARD_ENCORE_REV_EVT1A 0x1 >> +#define BOARD_ENCORE_REV_EVT1B 0x2 >> +#define BOARD_ENCORE_REV_EVT2 0x3 >> +#define BOARD_ENCORE_REV_DVT 0x4 >> +#define BOARD_ENCORE_REV_PVT 0x5 >> +#define BOARD_ENCORE_REV_UNKNOWN 0x6 >> + >> +static inline int is_encore_board_evt2(void) >> +{ >> + return (system_rev >= BOARD_ENCORE_REV_EVT2); >> +} >> + >> +static inline int is_encore_board_evt1b(void) >> +{ >> + return (system_rev == BOARD_ENCORE_REV_EVT1B); >> +} >> + >> +static int encore_twl4030_keymap[] = { >> + KEY(0, 0, KEY_HOME), >> + KEY(0, 1, KEY_VOLUMEUP), >> + KEY(0, 2, KEY_VOLUMEDOWN), >> + 0 >> +}; >> + >> +static struct matrix_keymap_data encore_twl4030_keymap_data = { >> + .keymap = encore_twl4030_keymap, >> + .keymap_size = ARRAY_SIZE(encore_twl4030_keymap), >> +}; >> + >> +static struct twl4030_keypad_data encore_kp_twl4030_data = { >> + .rows = 8, >> + .cols = 8, >> + .keymap_data = &encore_twl4030_keymap_data, >> + .rep = 1, >> +}; >> + >> +/* HOME key code for HW > EVT2A */ >> +static struct gpio_keys_button encore_gpio_buttons[] = { >> + { >> + .code = KEY_POWER, >> + .gpio = 14, >> + .desc = "POWER", >> + .active_low = 0, >> + .wakeup = 1, >> + }, >> + { >> + .code = KEY_HOME, >> + .gpio = 48, >> + .desc = "HOME", >> + .active_low = 1, >> + .wakeup = 1, >> + }, >> +}; >> + >> +static struct gpio_keys_platform_data encore_gpio_key_info = { >> + .buttons = encore_gpio_buttons, >> + .nbuttons = ARRAY_SIZE(encore_gpio_buttons), >> +}; >> + >> +static struct platform_device encore_keys_gpio = { >> + .name = "gpio-keys", >> + .id = -1, >> + .dev = { >> + .platform_data = &encore_gpio_key_info, >> + }, >> +}; >> + >> +static struct platform_device *encore_devices[] __initdata = { >> + &encore_keys_gpio, >> +}; >> + >> +static void __init omap_encore_init_early(void) >> +{ >> + omap2_init_common_infrastructure(); >> + omap2_init_common_devices(h8mbx00u0mer0em_sdrc_params, >> + h8mbx00u0mer0em_sdrc_params); >> +} >> + >> +static struct twl4030_usb_data encore_usb_data = { >> + .usb_mode = T2_USB_MODE_ULPI, >> +}; >> + >> +static struct regulator_consumer_supply encore_vmmc1_supply = { >> + .supply = "vmmc", >> +}; >> + >> +static struct regulator_consumer_supply encore_vdda_dac_supply = >> + REGULATOR_SUPPLY("vdda_dac", "omapdss_venc"); >> + >> +/* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */ >> +static struct regulator_init_data encore_vmmc1 = { >> + .constraints = { >> + .min_uV = 1850000, >> + .max_uV = 3150000, >> + .valid_modes_mask = REGULATOR_MODE_NORMAL >> + | REGULATOR_MODE_STANDBY, >> + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE >> + | REGULATOR_CHANGE_MODE >> + | REGULATOR_CHANGE_STATUS, >> + }, >> + .num_consumer_supplies = 1, >> + .consumer_supplies = &encore_vmmc1_supply, >> +}; >> + >> +static struct regulator_init_data encore_vdac = { >> + .constraints = { >> + .min_uV = 1800000, >> + .max_uV = 1800000, >> + .valid_modes_mask = REGULATOR_MODE_NORMAL >> + | REGULATOR_MODE_STANDBY, >> + .valid_ops_mask = REGULATOR_CHANGE_MODE >> + | REGULATOR_CHANGE_STATUS, >> + }, >> + .num_consumer_supplies = 1, >> + .consumer_supplies = &encore_vdda_dac_supply, >> +}; >> + >> +/* The order is reverted in this table so that internal eMMC is presented >> + * as first mmc card for compatibility with existing installations and >> + * for common sense reasons */ >> +static struct omap2_hsmmc_info mmc[] __initdata = { >> + { >> + .name = "internal", >> + .mmc = 2, >> + .caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA, >> + .gpio_cd = -EINVAL, >> + .gpio_wp = -EINVAL, >> + .nonremovable = true, >> + .power_saving = true, >> + .ocr_mask = MMC_VDD_165_195, /* 1.85V */ >> + }, >> + { >> + .name = "external", >> + .mmc = 1, >> + .caps = MMC_CAP_4_BIT_DATA, >> + .gpio_cd = -EINVAL, >> + .gpio_wp = -EINVAL, >> + .power_saving = true, >> + }, >> + { >> + .name = "internal", >> + .mmc = 3, >> + .caps = MMC_CAP_4_BIT_DATA, >> + .gpio_cd = -EINVAL, >> + .gpio_wp = -EINVAL, >> + .nonremovable = true, >> + .power_saving = true, >> + }, >> + {} /* Terminator */ >> +}; >> + >> +static int encore_hsmmc_card_detect(struct device *dev, int slot) >> +{ >> + struct omap_mmc_platform_data *mmc = dev->platform_data; >> + >> + /* Encore board EVT2 and later has pin high when card is present) */ >> + return gpio_get_value_cansleep(mmc->slots[0].switch_pin); >> +} >> + >> +static int encore_twl4030_hsmmc_late_init(struct device *dev) >> +{ >> + int ret = 0; >> + struct platform_device *pdev = container_of(dev, >> + struct platform_device, dev); >> + struct omap_mmc_platform_data *pdata = dev->platform_data; >> + >> + if(is_encore_board_evt2()) { >> + /* Setting MMC1 (external) Card detect */ >> + if (pdev->id == 0) { >> + pdata->slots[0].card_detect = encore_hsmmc_card_detect; >> + } >> + } >> + return ret; >> +} >> + >> +static __init void encore_hsmmc_set_late_init(struct device *dev) >> +{ >> + struct omap_mmc_platform_data *pdata; >> + >> + /* dev can be null if CONFIG_MMC_OMAP_HS is not set */ >> + if (!dev) >> + return; >> + >> + pdata = dev->platform_data; >> + pdata->init = encore_twl4030_hsmmc_late_init; >> +} >> + >> +static int __ref encore_twl_gpio_setup(struct device *dev, >> + unsigned gpio, unsigned ngpio) >> +{ >> + struct omap2_hsmmc_info *c; >> + /* >> + * gpio + 0 is "mmc0_cd" (input/IRQ), >> + * gpio + 1 is "mmc1_cd" (input/IRQ) >> + */ >> + mmc[1].gpio_cd = gpio + 0; >> + mmc[0].gpio_cd = gpio + 1; >> + omap2_hsmmc_init(mmc); >> + for (c = mmc; c->mmc; c++) >> + encore_hsmmc_set_late_init(c->dev); >> + >> + /* >> + * link regulators to MMC adapters ... we "know" the >> + * regulators will be set up only *after* we return. >> + */ >> + encore_vmmc1_supply.dev = mmc[1].dev; >> + >> + return 0; >> +} >> + >> +static struct twl4030_gpio_platform_data encore_gpio_data = { >> + .gpio_base = OMAP_MAX_GPIO_LINES, >> + .irq_base = TWL4030_GPIO_IRQ_BASE, >> + .irq_end = TWL4030_GPIO_IRQ_END, >> + .setup = encore_twl_gpio_setup, >> +}; >> + >> +static struct twl4030_madc_platform_data encore_madc_data = { >> + .irq_line = 1, >> +}; >> + >> +static struct twl4030_platform_data __refdata encore_twldata = { >> + .irq_base = TWL4030_IRQ_BASE, >> + .irq_end = TWL4030_IRQ_END, >> + >> + .madc = &encore_madc_data, >> + .usb = &encore_usb_data, >> + .gpio = &encore_gpio_data, >> + .keypad = &encore_kp_twl4030_data, >> + .vmmc1 = &encore_vmmc1, >> + .vdac = &encore_vdac, >> +}; >> + >> +static struct i2c_board_info __initdata encore_i2c_bus1_info[] = { >> + { >> + I2C_BOARD_INFO("tps65921", 0x48), >> + .flags = I2C_CLIENT_WAKE, >> + .irq = INT_34XX_SYS_NIRQ, >> + .platform_data = &encore_twldata, >> + }, >> +}; >> + >> +static struct i2c_board_info __initdata encore_i2c_bus2_info[] = { >> +}; >> + >> + >> +static struct omap_musb_board_data musb_board_data = { >> + .interface_type = MUSB_INTERFACE_ULPI, >> +#ifdef CONFIG_USB_MUSB_OTG >> + .mode = MUSB_OTG, >> +#elif defined(CONFIG_USB_MUSB_HDRC_HCD) >> + .mode = MUSB_HOST, >> +#elif defined(CONFIG_USB_GADGET_MUSB_HDRC) >> + .mode = MUSB_PERIPHERAL, >> +#endif >> + .power = 100, >> +}; >> + >> +#ifdef CONFIG_OMAP_MUX >> +static struct omap_board_mux board_mux[] __initdata = { >> + { .reg_offset = OMAP_MUX_TERMINATOR }, >> +}; >> +#else >> +#define board_mux NULL >> +#endif >> + >> +static struct omap_board_config_kernel encore_config[] __initdata = { >> +}; >> + >> +static int __init omap_i2c_init(void) >> +{ >> + omap_register_i2c_bus(1, 100, encore_i2c_bus1_info, >> + ARRAY_SIZE(encore_i2c_bus1_info)); >> + omap_register_i2c_bus(2, 400, encore_i2c_bus2_info, >> + ARRAY_SIZE(encore_i2c_bus2_info)); >> + return 0; >> +} >> + >> +static void __init omap_encore_init(void) >> +{ >> + omap3_mux_init(board_mux, OMAP_PACKAGE_CBB); >> + omap_i2c_init(); >> + omap_serial_init(); >> + usb_musb_init(&musb_board_data); >> + >> + omap_board_config = encore_config; >> + omap_board_config_size = ARRAY_SIZE(encore_config); >> + >> + platform_add_devices(encore_devices, ARRAY_SIZE(encore_devices)); >> +} >> + >> +MACHINE_START(ENCORE, "encore") >> + .boot_params = 0x80000100, >> + .reserve = omap_reserve, >> + .map_io = omap3_map_io, >> + .init_early = omap_encore_init_early, >> + .init_irq = omap_init_irq, >> + .init_machine = omap_encore_init, >> + .timer = &omap_timer, >> +MACHINE_END >> diff --git a/arch/arm/plat-omap/include/plat/uncompress.h b/arch/arm/plat-omap/include/plat/uncompress.h >> index 30b891c..f2de4ff 100644 >> --- a/arch/arm/plat-omap/include/plat/uncompress.h >> +++ b/arch/arm/plat-omap/include/plat/uncompress.h >> @@ -161,6 +161,7 @@ static inline void __arch_decomp_setup(unsigned long arch_id) >> DEBUG_LL_OMAP3(3, omap_ldp); >> DEBUG_LL_OMAP3(3, overo); >> DEBUG_LL_OMAP3(3, touchbook); >> + DEBUG_LL_OMAP3(3, encore); >> >> /* omap4 based boards using UART3 */ >> DEBUG_LL_OMAP4(3, omap_4430sdp); >> diff --git a/arch/arm/tools/mach-types b/arch/arm/tools/mach-types >> index 7ca41f0..2f0db3e 100644 >> --- a/arch/arm/tools/mach-types >> +++ b/arch/arm/tools/mach-types >> @@ -962,7 +962,7 @@ omapl138_case_a3 MACH_OMAPL138_CASE_A3 OMAPL138_CASE_A3 3280 >> uemd MACH_UEMD UEMD 3281 >> ccwmx51mut MACH_CCWMX51MUT CCWMX51MUT 3282 >> rockhopper MACH_ROCKHOPPER ROCKHOPPER 3283 >> -nookcolor MACH_NOOKCOLOR NOOKCOLOR 3284 >> +encore MACH_ENCORE ENCORE 3284 >> hkdkc100 MACH_HKDKC100 HKDKC100 3285 >> ts42xx MACH_TS42XX TS42XX 3286 >> aebl MACH_AEBL AEBL 3287 >> -- >> 1.7.4.4 >> >> -- >> To unsubscribe from this list: send the line "unsubscribe linux-omap" in >> the body of a message to majordomo@vger.kernel.org >> More majordomo info at http://vger.kernel.org/majordomo-info.html >> ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH 1/2] Initial B&N Nook Color (encore) support. 2011-04-29 0:49 ` Oleg Drokin @ 2011-05-03 11:08 ` Vladimir Pantelic 0 siblings, 0 replies; 9+ messages in thread From: Vladimir Pantelic @ 2011-05-03 11:08 UTC (permalink / raw) To: Oleg Drokin; +Cc: Abimanyu Gottumukkala, linux-omap Oleg Drokin wrote: > Hello! > > Is there any special support needed for 3621, though? > My understanding is that's just 3630 without a "phone" part? 3621 is more or less a 3630 in a different package, less pins, 0.5mm ball pitch and no PoP option. > The .29 kernel they had only added is_omap3621 stuff that's not > called anywhere, but smartreflex code (I guess that's might be > useful to add too of course). > > I know about the new code drop is coming, but I don't > expect there to be any basic stuff changes (and this board file > is coming pretty barebones right now), besides I am not so > optimistic to actually expect this patch to be merged right away, > but I am already gathering valuable feedback. ;) > > BTW I saw in the archives that you are also working a port, > do you have your tree hosted anywhere? > > Bye, > Oleg > On Apr 28, 2011, at 7:34 PM, Abimanyu Gottumukkala wrote: > >> Hi, >> >> Nook color has Ti OMAP 3621. 3621 CPU Support is not available in >> current kernel, adding CPU support will be nice before board. >> BN is set to release new source code in few days, taking new code as >> porting base is also recommended. >> >> Regards, >> Abimanyu G >> >> On Thu, Apr 28, 2011 at 9:27 PM,<green@linuxhacker.ru> wrote: >>> From: Oleg Drokin<green@linuxhacker.ru> >>> >>> Bare-bones board file, comes with serial console, gpio keys, >>> MMC/SDCard and USB support. >>> --- >>> arch/arm/mach-omap2/Kconfig | 5 + >>> arch/arm/mach-omap2/Makefile | 2 + >>> arch/arm/mach-omap2/board-omap3encore.c | 380 ++++++++++++++++++++++++++ >>> arch/arm/plat-omap/include/plat/uncompress.h | 1 + >>> arch/arm/tools/mach-types | 2 +- >>> 5 files changed, 389 insertions(+), 1 deletions(-) >>> create mode 100644 arch/arm/mach-omap2/board-omap3encore.c >>> >>> diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig >>> index b997a35..5370561 100644 >>> --- a/arch/arm/mach-omap2/Kconfig >>> +++ b/arch/arm/mach-omap2/Kconfig >>> @@ -173,6 +173,11 @@ config MACH_OMAP3_TORPEDO >>> for full description please see the products webpage at >>> http://www.logicpd.com/products/development-kits/zoom-omap35x-torpedo-development-kit >>> >>> +config MACH_ENCORE >>> + bool "Barnes& Noble Encore (Nook Color)" >>> + depends on ARCH_OMAP3 >>> + select OMAP_PACKAGE_CBP >>> + >>> config MACH_OVERO >>> bool "Gumstix Overo board" >>> depends on ARCH_OMAP3 >>> diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile >>> index 512b152..b894777 100644 >>> --- a/arch/arm/mach-omap2/Makefile >>> +++ b/arch/arm/mach-omap2/Makefile >>> @@ -189,6 +189,8 @@ obj-$(CONFIG_MACH_OMAP3530_LV_SOM) += board-omap3logic.o \ >>> hsmmc.o >>> obj-$(CONFIG_MACH_OMAP3_TORPEDO) += board-omap3logic.o \ >>> hsmmc.o >>> +obj-$(CONFIG_MACH_ENCORE) += board-omap3encore.o \ >>> + hsmmc.o >>> obj-$(CONFIG_MACH_OVERO) += board-overo.o \ >>> hsmmc.o >>> obj-$(CONFIG_MACH_OMAP3EVM) += board-omap3evm.o \ >>> diff --git a/arch/arm/mach-omap2/board-omap3encore.c b/arch/arm/mach-omap2/board-omap3encore.c >>> new file mode 100644 >>> index 0000000..c7bf8de >>> --- /dev/null >>> +++ b/arch/arm/mach-omap2/board-omap3encore.c >>> @@ -0,0 +1,380 @@ >>> +/* >>> + * >>> + * Copyright (C) 2008 Texas Instruments Inc. >>> + * Vikram Pandita<vikram.pandita@ti.com> >>> + * >>> + * Modified from mach-omap2/board-ldp.c >>> + * >>> + * This program is free software; you can redistribute it and/or modify >>> + * it under the terms of the GNU General Public License version 2 as >>> + * published by the Free Software Foundation. >>> + * >>> + * April 2011 Oleg Drokin<green@linuxhacker.ru> - Port to 2.6.39 >>> + * >>> + */ >>> + >>> +#include<linux/kernel.h> >>> +#include<linux/platform_device.h> >>> +#include<linux/gpio_keys.h> >>> +#include<linux/err.h> >>> + >>> +#include<linux/spi/spi.h> >>> +#include<linux/i2c/twl.h> >>> +#include<linux/regulator/machine.h> >>> +#include<linux/regulator/fixed.h> >>> +#include<mach/hardware.h> >>> +#include<asm/mach-types.h> >>> +#include<asm/mach/arch.h> >>> + >>> +#include<mach/gpio.h> >>> +#include<plat/board.h> >>> +#include<plat/common.h> >>> +#include<plat/usb.h> >>> +#include<plat/mux.h> >>> +#include<plat/sram.h> >>> +#include<plat/mmc.h> >>> +#include<plat/omap-serial.h> >>> +#include<plat/system.h> >>> + >>> +#include "mux.h" >>> +#include "hsmmc.h" >>> +#include "sdram-hynix-h8mbx00u0mer-0em.h" >>> + >>> +/* Encore-specific device-info and i2c addresses. */ >>> +/* Battery, bus 1 */ >>> +#define MAX17042_I2C_SLAVE_ADDRESS 0x36 >>> +#define MAX17042_GPIO_FOR_IRQ 100 >>> + >>> +/*addition of MAXIM8903/TI GPIO mapping WRT schematics */ >>> +#define MAX8903_UOK_GPIO_FOR_IRQ 115 >>> +#define MAX8903_DOK_GPIO_FOR_IRQ 114 >>> +#define MAX8903_GPIO_CHG_EN 110 >>> +#define MAX8903_GPIO_CHG_STATUS 111 >>> +#define MAX8903_GPIO_CHG_FLT 101 >>> +#define MAX8903_GPIO_CHG_IUSB 102 >>> +#define MAX8903_GPIO_CHG_USUS 104 >>> +#define MAX8903_GPIO_CHG_ILM 61 >>> + >>> +/* TI WLAN */ >>> +#define ENCORE_WIFI_PMENA_GPIO 22 >>> +#define ENCORE_WIFI_IRQ_GPIO 15 >>> +#define ENCORE_WIFI_EN_POW 16 >>> + >>> +/* Accelerometer i2c bus 1*/ >>> +#define KXTF9_I2C_SLAVE_ADDRESS 0x0F >>> +#define KXTF9_GPIO_FOR_PWR 34 >>> +#define KXTF9_GPIO_FOR_IRQ 113 >>> + >>> +/* Touch screen i2c bus 2*/ >>> +#define CYTTSP_I2C_SLAVEADDRESS 34 >>> +#define ENCORE_CYTTSP_GPIO 99 >>> +#define ENCORE_CYTTSP_RESET_GPIO 46 >>> + >>> +/* Audio codec, i2c bus 2 */ >>> +#define AUDIO_CODEC_POWER_ENABLE_GPIO 103 >>> +#define AUDIO_CODEC_RESET_GPIO 37 >>> +#define AUDIO_CODEC_IRQ_GPIO 59 >>> +#define AIC3100_I2CSLAVEADDRESS 0x18 >>> + >>> + >>> +/* Different HW revisions */ >>> +#define BOARD_ENCORE_REV_EVT1A 0x1 >>> +#define BOARD_ENCORE_REV_EVT1B 0x2 >>> +#define BOARD_ENCORE_REV_EVT2 0x3 >>> +#define BOARD_ENCORE_REV_DVT 0x4 >>> +#define BOARD_ENCORE_REV_PVT 0x5 >>> +#define BOARD_ENCORE_REV_UNKNOWN 0x6 >>> + >>> +static inline int is_encore_board_evt2(void) >>> +{ >>> + return (system_rev>= BOARD_ENCORE_REV_EVT2); >>> +} >>> + >>> +static inline int is_encore_board_evt1b(void) >>> +{ >>> + return (system_rev == BOARD_ENCORE_REV_EVT1B); >>> +} >>> + >>> +static int encore_twl4030_keymap[] = { >>> + KEY(0, 0, KEY_HOME), >>> + KEY(0, 1, KEY_VOLUMEUP), >>> + KEY(0, 2, KEY_VOLUMEDOWN), >>> + 0 >>> +}; >>> + >>> +static struct matrix_keymap_data encore_twl4030_keymap_data = { >>> + .keymap = encore_twl4030_keymap, >>> + .keymap_size = ARRAY_SIZE(encore_twl4030_keymap), >>> +}; >>> + >>> +static struct twl4030_keypad_data encore_kp_twl4030_data = { >>> + .rows = 8, >>> + .cols = 8, >>> + .keymap_data =&encore_twl4030_keymap_data, >>> + .rep = 1, >>> +}; >>> + >>> +/* HOME key code for HW> EVT2A */ >>> +static struct gpio_keys_button encore_gpio_buttons[] = { >>> + { >>> + .code = KEY_POWER, >>> + .gpio = 14, >>> + .desc = "POWER", >>> + .active_low = 0, >>> + .wakeup = 1, >>> + }, >>> + { >>> + .code = KEY_HOME, >>> + .gpio = 48, >>> + .desc = "HOME", >>> + .active_low = 1, >>> + .wakeup = 1, >>> + }, >>> +}; >>> + >>> +static struct gpio_keys_platform_data encore_gpio_key_info = { >>> + .buttons = encore_gpio_buttons, >>> + .nbuttons = ARRAY_SIZE(encore_gpio_buttons), >>> +}; >>> + >>> +static struct platform_device encore_keys_gpio = { >>> + .name = "gpio-keys", >>> + .id = -1, >>> + .dev = { >>> + .platform_data =&encore_gpio_key_info, >>> + }, >>> +}; >>> + >>> +static struct platform_device *encore_devices[] __initdata = { >>> +&encore_keys_gpio, >>> +}; >>> + >>> +static void __init omap_encore_init_early(void) >>> +{ >>> + omap2_init_common_infrastructure(); >>> + omap2_init_common_devices(h8mbx00u0mer0em_sdrc_params, >>> + h8mbx00u0mer0em_sdrc_params); >>> +} >>> + >>> +static struct twl4030_usb_data encore_usb_data = { >>> + .usb_mode = T2_USB_MODE_ULPI, >>> +}; >>> + >>> +static struct regulator_consumer_supply encore_vmmc1_supply = { >>> + .supply = "vmmc", >>> +}; >>> + >>> +static struct regulator_consumer_supply encore_vdda_dac_supply = >>> + REGULATOR_SUPPLY("vdda_dac", "omapdss_venc"); >>> + >>> +/* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */ >>> +static struct regulator_init_data encore_vmmc1 = { >>> + .constraints = { >>> + .min_uV = 1850000, >>> + .max_uV = 3150000, >>> + .valid_modes_mask = REGULATOR_MODE_NORMAL >>> + | REGULATOR_MODE_STANDBY, >>> + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE >>> + | REGULATOR_CHANGE_MODE >>> + | REGULATOR_CHANGE_STATUS, >>> + }, >>> + .num_consumer_supplies = 1, >>> + .consumer_supplies =&encore_vmmc1_supply, >>> +}; >>> + >>> +static struct regulator_init_data encore_vdac = { >>> + .constraints = { >>> + .min_uV = 1800000, >>> + .max_uV = 1800000, >>> + .valid_modes_mask = REGULATOR_MODE_NORMAL >>> + | REGULATOR_MODE_STANDBY, >>> + .valid_ops_mask = REGULATOR_CHANGE_MODE >>> + | REGULATOR_CHANGE_STATUS, >>> + }, >>> + .num_consumer_supplies = 1, >>> + .consumer_supplies =&encore_vdda_dac_supply, >>> +}; >>> + >>> +/* The order is reverted in this table so that internal eMMC is presented >>> + * as first mmc card for compatibility with existing installations and >>> + * for common sense reasons */ >>> +static struct omap2_hsmmc_info mmc[] __initdata = { >>> + { >>> + .name = "internal", >>> + .mmc = 2, >>> + .caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA, >>> + .gpio_cd = -EINVAL, >>> + .gpio_wp = -EINVAL, >>> + .nonremovable = true, >>> + .power_saving = true, >>> + .ocr_mask = MMC_VDD_165_195, /* 1.85V */ >>> + }, >>> + { >>> + .name = "external", >>> + .mmc = 1, >>> + .caps = MMC_CAP_4_BIT_DATA, >>> + .gpio_cd = -EINVAL, >>> + .gpio_wp = -EINVAL, >>> + .power_saving = true, >>> + }, >>> + { >>> + .name = "internal", >>> + .mmc = 3, >>> + .caps = MMC_CAP_4_BIT_DATA, >>> + .gpio_cd = -EINVAL, >>> + .gpio_wp = -EINVAL, >>> + .nonremovable = true, >>> + .power_saving = true, >>> + }, >>> + {} /* Terminator */ >>> +}; >>> + >>> +static int encore_hsmmc_card_detect(struct device *dev, int slot) >>> +{ >>> + struct omap_mmc_platform_data *mmc = dev->platform_data; >>> + >>> + /* Encore board EVT2 and later has pin high when card is present) */ >>> + return gpio_get_value_cansleep(mmc->slots[0].switch_pin); >>> +} >>> + >>> +static int encore_twl4030_hsmmc_late_init(struct device *dev) >>> +{ >>> + int ret = 0; >>> + struct platform_device *pdev = container_of(dev, >>> + struct platform_device, dev); >>> + struct omap_mmc_platform_data *pdata = dev->platform_data; >>> + >>> + if(is_encore_board_evt2()) { >>> + /* Setting MMC1 (external) Card detect */ >>> + if (pdev->id == 0) { >>> + pdata->slots[0].card_detect = encore_hsmmc_card_detect; >>> + } >>> + } >>> + return ret; >>> +} >>> + >>> +static __init void encore_hsmmc_set_late_init(struct device *dev) >>> +{ >>> + struct omap_mmc_platform_data *pdata; >>> + >>> + /* dev can be null if CONFIG_MMC_OMAP_HS is not set */ >>> + if (!dev) >>> + return; >>> + >>> + pdata = dev->platform_data; >>> + pdata->init = encore_twl4030_hsmmc_late_init; >>> +} >>> + >>> +static int __ref encore_twl_gpio_setup(struct device *dev, >>> + unsigned gpio, unsigned ngpio) >>> +{ >>> + struct omap2_hsmmc_info *c; >>> + /* >>> + * gpio + 0 is "mmc0_cd" (input/IRQ), >>> + * gpio + 1 is "mmc1_cd" (input/IRQ) >>> + */ >>> + mmc[1].gpio_cd = gpio + 0; >>> + mmc[0].gpio_cd = gpio + 1; >>> + omap2_hsmmc_init(mmc); >>> + for (c = mmc; c->mmc; c++) >>> + encore_hsmmc_set_late_init(c->dev); >>> + >>> + /* >>> + * link regulators to MMC adapters ... we "know" the >>> + * regulators will be set up only *after* we return. >>> + */ >>> + encore_vmmc1_supply.dev = mmc[1].dev; >>> + >>> + return 0; >>> +} >>> + >>> +static struct twl4030_gpio_platform_data encore_gpio_data = { >>> + .gpio_base = OMAP_MAX_GPIO_LINES, >>> + .irq_base = TWL4030_GPIO_IRQ_BASE, >>> + .irq_end = TWL4030_GPIO_IRQ_END, >>> + .setup = encore_twl_gpio_setup, >>> +}; >>> + >>> +static struct twl4030_madc_platform_data encore_madc_data = { >>> + .irq_line = 1, >>> +}; >>> + >>> +static struct twl4030_platform_data __refdata encore_twldata = { >>> + .irq_base = TWL4030_IRQ_BASE, >>> + .irq_end = TWL4030_IRQ_END, >>> + >>> + .madc =&encore_madc_data, >>> + .usb =&encore_usb_data, >>> + .gpio =&encore_gpio_data, >>> + .keypad =&encore_kp_twl4030_data, >>> + .vmmc1 =&encore_vmmc1, >>> + .vdac =&encore_vdac, >>> +}; >>> + >>> +static struct i2c_board_info __initdata encore_i2c_bus1_info[] = { >>> + { >>> + I2C_BOARD_INFO("tps65921", 0x48), >>> + .flags = I2C_CLIENT_WAKE, >>> + .irq = INT_34XX_SYS_NIRQ, >>> + .platform_data =&encore_twldata, >>> + }, >>> +}; >>> + >>> +static struct i2c_board_info __initdata encore_i2c_bus2_info[] = { >>> +}; >>> + >>> + >>> +static struct omap_musb_board_data musb_board_data = { >>> + .interface_type = MUSB_INTERFACE_ULPI, >>> +#ifdef CONFIG_USB_MUSB_OTG >>> + .mode = MUSB_OTG, >>> +#elif defined(CONFIG_USB_MUSB_HDRC_HCD) >>> + .mode = MUSB_HOST, >>> +#elif defined(CONFIG_USB_GADGET_MUSB_HDRC) >>> + .mode = MUSB_PERIPHERAL, >>> +#endif >>> + .power = 100, >>> +}; >>> + >>> +#ifdef CONFIG_OMAP_MUX >>> +static struct omap_board_mux board_mux[] __initdata = { >>> + { .reg_offset = OMAP_MUX_TERMINATOR }, >>> +}; >>> +#else >>> +#define board_mux NULL >>> +#endif >>> + >>> +static struct omap_board_config_kernel encore_config[] __initdata = { >>> +}; >>> + >>> +static int __init omap_i2c_init(void) >>> +{ >>> + omap_register_i2c_bus(1, 100, encore_i2c_bus1_info, >>> + ARRAY_SIZE(encore_i2c_bus1_info)); >>> + omap_register_i2c_bus(2, 400, encore_i2c_bus2_info, >>> + ARRAY_SIZE(encore_i2c_bus2_info)); >>> + return 0; >>> +} >>> + >>> +static void __init omap_encore_init(void) >>> +{ >>> + omap3_mux_init(board_mux, OMAP_PACKAGE_CBB); >>> + omap_i2c_init(); >>> + omap_serial_init(); >>> + usb_musb_init(&musb_board_data); >>> + >>> + omap_board_config = encore_config; >>> + omap_board_config_size = ARRAY_SIZE(encore_config); >>> + >>> + platform_add_devices(encore_devices, ARRAY_SIZE(encore_devices)); >>> +} >>> + >>> +MACHINE_START(ENCORE, "encore") >>> + .boot_params = 0x80000100, >>> + .reserve = omap_reserve, >>> + .map_io = omap3_map_io, >>> + .init_early = omap_encore_init_early, >>> + .init_irq = omap_init_irq, >>> + .init_machine = omap_encore_init, >>> + .timer =&omap_timer, >>> +MACHINE_END >>> diff --git a/arch/arm/plat-omap/include/plat/uncompress.h b/arch/arm/plat-omap/include/plat/uncompress.h >>> index 30b891c..f2de4ff 100644 >>> --- a/arch/arm/plat-omap/include/plat/uncompress.h >>> +++ b/arch/arm/plat-omap/include/plat/uncompress.h >>> @@ -161,6 +161,7 @@ static inline void __arch_decomp_setup(unsigned long arch_id) >>> DEBUG_LL_OMAP3(3, omap_ldp); >>> DEBUG_LL_OMAP3(3, overo); >>> DEBUG_LL_OMAP3(3, touchbook); >>> + DEBUG_LL_OMAP3(3, encore); >>> >>> /* omap4 based boards using UART3 */ >>> DEBUG_LL_OMAP4(3, omap_4430sdp); >>> diff --git a/arch/arm/tools/mach-types b/arch/arm/tools/mach-types >>> index 7ca41f0..2f0db3e 100644 >>> --- a/arch/arm/tools/mach-types >>> +++ b/arch/arm/tools/mach-types >>> @@ -962,7 +962,7 @@ omapl138_case_a3 MACH_OMAPL138_CASE_A3 OMAPL138_CASE_A3 3280 >>> uemd MACH_UEMD UEMD 3281 >>> ccwmx51mut MACH_CCWMX51MUT CCWMX51MUT 3282 >>> rockhopper MACH_ROCKHOPPER ROCKHOPPER 3283 >>> -nookcolor MACH_NOOKCOLOR NOOKCOLOR 3284 >>> +encore MACH_ENCORE ENCORE 3284 >>> hkdkc100 MACH_HKDKC100 HKDKC100 3285 >>> ts42xx MACH_TS42XX TS42XX 3286 >>> aebl MACH_AEBL AEBL 3287 >>> -- >>> 1.7.4.4 >>> >>> -- >>> To unsubscribe from this list: send the line "unsubscribe linux-omap" in >>> the body of a message to majordomo@vger.kernel.org >>> More majordomo info at http://vger.kernel.org/majordomo-info.html >>> > > -- > To unsubscribe from this list: send the line "unsubscribe linux-omap" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH 1/2] Initial B&N Nook Color (encore) support. 2011-04-28 15:57 ` [PATCH 1/2] Initial B&N Nook Color (encore) support green 2011-04-28 23:34 ` Abimanyu Gottumukkala @ 2011-05-03 9:22 ` Tony Lindgren 1 sibling, 0 replies; 9+ messages in thread From: Tony Lindgren @ 2011-05-03 9:22 UTC (permalink / raw) To: green; +Cc: linux-omap * green@linuxhacker.ru <green@linuxhacker.ru> [110428 08:55]: > From: Oleg Drokin <green@linuxhacker.ru> > > Bare-bones board file, comes with serial console, gpio keys, > MMC/SDCard and USB support. Good to see that. Unfortunately you probably have to do few more rebases on the devel-cleanup branch because of the code consolidation effort. We'll have to wait a bit and see what new platform code we can merge after that is all the consolidation is sorted out. Please also post your series with linux-arm-kernel mailing list Cc'd. Few comments below too. > +#include <mach/gpio.h> This should be linux/gpio.h nowadays. > + if(is_encore_board_evt2()) { You should have if ( here with space. Maybe run scripts/checkpatch.pl --strict on the patch? > --- a/arch/arm/tools/mach-types > +++ b/arch/arm/tools/mach-types > @@ -962,7 +962,7 @@ omapl138_case_a3 MACH_OMAPL138_CASE_A3 OMAPL138_CASE_A3 3280 > uemd MACH_UEMD UEMD 3281 > ccwmx51mut MACH_CCWMX51MUT CCWMX51MUT 3282 > rockhopper MACH_ROCKHOPPER ROCKHOPPER 3283 > -nookcolor MACH_NOOKCOLOR NOOKCOLOR 3284 > +encore MACH_ENCORE ENCORE 3284 > hkdkc100 MACH_HKDKC100 HKDKC100 3285 > ts42xx MACH_TS42XX TS42XX 3286 > aebl MACH_AEBL AEBL 3287 For this you need to follow the instructions at www.arm.linux.org.uk. Regards, Tony ^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH 2/2] Add tps65921 chip 2011-04-28 15:57 Initial B&N Nook Color support, take two green 2011-04-28 15:57 ` [PATCH 1/2] Initial B&N Nook Color (encore) support green @ 2011-04-28 15:57 ` green 2011-04-28 17:05 ` Initial B&N Nook Color support, take two Paul Walmsley 2 siblings, 0 replies; 9+ messages in thread From: green @ 2011-04-28 15:57 UTC (permalink / raw) To: linux-omap; +Cc: Oleg Drokin From: Oleg Drokin <green@linuxhacker.ru> --- drivers/mfd/twl-core.c | 2 ++ 1 files changed, 2 insertions(+), 0 deletions(-) diff --git a/drivers/mfd/twl-core.c b/drivers/mfd/twl-core.c index 960b5be..3daebcc 100644 --- a/drivers/mfd/twl-core.c +++ b/drivers/mfd/twl-core.c @@ -1107,6 +1107,8 @@ static const struct i2c_device_id twl_ids[] = { { "tps65950", 0 }, /* catalog version of twl5030 */ { "tps65930", TPS_SUBSET }, /* fewer LDOs and DACs; no charger */ { "tps65920", TPS_SUBSET }, /* fewer LDOs; no codec or charger */ + { "tps65921", TPS_SUBSET }, /* fewer LDOs; no codec, no LED + and vibrator. Charger in USB module*/ { "twl6030", TWL6030_CLASS }, /* "Phoenix power chip" */ { /* end of list */ }, }; -- 1.7.4.4 ^ permalink raw reply related [flat|nested] 9+ messages in thread
* Re: Initial B&N Nook Color support, take two 2011-04-28 15:57 Initial B&N Nook Color support, take two green 2011-04-28 15:57 ` [PATCH 1/2] Initial B&N Nook Color (encore) support green 2011-04-28 15:57 ` [PATCH 2/2] Add tps65921 chip green @ 2011-04-28 17:05 ` Paul Walmsley 2011-04-28 17:21 ` Oleg Drokin 2 siblings, 1 reply; 9+ messages in thread From: Paul Walmsley @ 2011-04-28 17:05 UTC (permalink / raw) To: green; +Cc: linux-omap On Thu, 28 Apr 2011, green@linuxhacker.ru wrote: > Hello! > > Ok, this is a second attempt at B&N Nook Color board file submission. > USB peripheral mode is fully operational as is serial console and > MMC/SDCard. It's good that you're sending these patches, but please also: - Add a Signed-off-by: to each patch (see item 12 of Documentation/SubmittingPatches) - Cc Vikram, the original author of the board file, in the patch messages - Cc the linux-arm-kernel@lists.infradead.org mailing list - Paul ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: Initial B&N Nook Color support, take two 2011-04-28 17:05 ` Initial B&N Nook Color support, take two Paul Walmsley @ 2011-04-28 17:21 ` Oleg Drokin 0 siblings, 0 replies; 9+ messages in thread From: Oleg Drokin @ 2011-04-28 17:21 UTC (permalink / raw) To: Paul Walmsley; +Cc: linux-omap Hello! On Apr 28, 2011, at 1:05 PM, Paul Walmsley wrote: >> Ok, this is a second attempt at B&N Nook Color board file submission. >> USB peripheral mode is fully operational as is serial console and >> MMC/SDCard. > It's good that you're sending these patches, but please also: > - Add a Signed-off-by: to each patch (see item 12 of > Documentation/SubmittingPatches) Ah, sure. Somehow I assumed this one is auto generated for the patch submitter. (never was a problem in the past at least). > - Cc Vikram, the original author of the board file, in the patch messages Ok, though I am not sure he is the original author of the nook color board file (since (C) 2008 well predates the Nook Color), the work I base this all off is from NookColor B&N source code drop and unfortunately people that worked on it did not identify themselves (or I don't see it) aside from just names in some debug comments. > - Cc the linux-arm-kernel@lists.infradead.org mailing list Ok, I am expecting the patch will still get quite a bit of scrutiny so I'll wait for more feedback and next submission would be conforming. Thanks! Bye, Oleg ^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2011-05-03 11:08 UTC | newest] Thread overview: 9+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2011-04-28 15:57 Initial B&N Nook Color support, take two green 2011-04-28 15:57 ` [PATCH 1/2] Initial B&N Nook Color (encore) support green 2011-04-28 23:34 ` Abimanyu Gottumukkala 2011-04-29 0:49 ` Oleg Drokin 2011-05-03 11:08 ` Vladimir Pantelic 2011-05-03 9:22 ` Tony Lindgren 2011-04-28 15:57 ` [PATCH 2/2] Add tps65921 chip green 2011-04-28 17:05 ` Initial B&N Nook Color support, take two Paul Walmsley 2011-04-28 17:21 ` Oleg Drokin
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).