From: Roger Quadros <rogerq@ti.com>
To: stern@rowland.harvard.edu
Cc: gregkh@linuxfoundation.org, balbi@ti.com,
sergei.shtylyov@cogentembedded.com, khilman@linaro.org,
tony@atomide.com, ruslan.bilovol@ti.com,
linux-usb@vger.kernel.org, linux-omap@vger.kernel.org,
linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
Roger Quadros <rogerq@ti.com>
Subject: [PATCH 6/6] USB: ehci-omap: Implement suspend/resume
Date: Wed, 10 Jul 2013 19:23:25 +0300 [thread overview]
Message-ID: <1373473405-27589-1-git-send-email-rogerq@ti.com> (raw)
In-Reply-To: <1373473081-27181-1-git-send-email-rogerq@ti.com>
Call ehci_suspend/resume() during runtime suspend/resume
as well as system suspend/resume.
Use a flag "bound" to indicate that the HCD structures are valid.
This is only true between usb_add_hcd() and usb_remove_hcd() calls.
The flag can be used by omap_ehci_runtime_suspend/resume() handlers
to avoid calling ehci_suspend/resume() when we are no longer bound
to the HCD e.g. during probe() and remove();
Signed-off-by: Roger Quadros <rogerq@ti.com>
---
drivers/usb/host/ehci-omap.c | 64 ++++++++++++++++++++++++++++++++++++++++-
1 files changed, 62 insertions(+), 2 deletions(-)
diff --git a/drivers/usb/host/ehci-omap.c b/drivers/usb/host/ehci-omap.c
index 9bd7dfe..6d1fde97 100644
--- a/drivers/usb/host/ehci-omap.c
+++ b/drivers/usb/host/ehci-omap.c
@@ -69,6 +69,7 @@ static const char hcd_name[] = "ehci-omap";
struct omap_hcd {
struct usb_phy *phy[OMAP3_HS_USB_PORTS]; /* one PHY for each port */
int nports;
+ bool bound; /* HCD structures are valid */
};
static inline void ehci_write(void __iomem *base, u32 reg, u32 val)
@@ -159,6 +160,7 @@ static int ehci_hcd_omap_probe(struct platform_device *pdev)
hcd->rsrc_start = res->start;
hcd->rsrc_len = resource_size(res);
hcd->regs = regs;
+ hcd->has_wakeup_irq = true;
hcd_to_ehci(hcd)->caps = regs;
omap = (struct omap_hcd *)hcd_to_ehci(hcd)->priv;
@@ -216,6 +218,8 @@ static int ehci_hcd_omap_probe(struct platform_device *pdev)
goto err_pm_runtime;
}
+ omap->bound = true;
+
/*
* Bring PHYs out of reset for non PHY modes.
* Even though HSIC mode is a PHY-less mode, the reset
@@ -232,6 +236,8 @@ static int ehci_hcd_omap_probe(struct platform_device *pdev)
usb_phy_set_suspend(omap->phy[i], 0);
}
+ pm_runtime_put_sync(dev);
+
return 0;
err_pm_runtime:
@@ -264,7 +270,9 @@ static int ehci_hcd_omap_remove(struct platform_device *pdev)
struct omap_hcd *omap = (struct omap_hcd *)hcd_to_ehci(hcd)->priv;
int i;
+ pm_runtime_get_sync(dev);
usb_remove_hcd(hcd);
+ omap->bound = false;
for (i = 0; i < omap->nports; i++) {
if (omap->phy[i])
@@ -293,15 +301,67 @@ static const struct of_device_id omap_ehci_dt_ids[] = {
MODULE_DEVICE_TABLE(of, omap_ehci_dt_ids);
+static int omap_ehci_suspend(struct device *dev)
+{
+ struct usb_hcd *hcd = dev_get_drvdata(dev);
+
+ dev_dbg(dev, "%s\n", __func__);
+
+ return ehci_suspend(hcd, true);
+}
+
+static int omap_ehci_resume(struct device *dev)
+{
+ struct usb_hcd *hcd = dev_get_drvdata(dev);
+
+ dev_dbg(dev, "%s\n", __func__);
+
+ return ehci_resume(hcd, false);
+}
+
+static int omap_ehci_runtime_suspend(struct device *dev)
+{
+ struct usb_hcd *hcd = dev_get_drvdata(dev);
+ struct omap_hcd *omap = (struct omap_hcd *)hcd_to_ehci(hcd)->priv;
+ bool do_wakeup = device_may_wakeup(dev);
+
+ dev_dbg(dev, "%s\n", __func__);
+
+ if (omap->bound)
+ ehci_suspend(hcd, do_wakeup);
+
+ return 0;
+}
+
+static int omap_ehci_runtime_resume(struct device *dev)
+{
+ struct usb_hcd *hcd = dev_get_drvdata(dev);
+ struct omap_hcd *omap = (struct omap_hcd *)hcd_to_ehci(hcd)->priv;
+
+ dev_dbg(dev, "%s\n", __func__);
+
+ if (omap->bound)
+ ehci_resume(hcd, false);
+
+ return 0;
+}
+
+
+static const struct dev_pm_ops omap_ehci_pm_ops = {
+ .suspend = omap_ehci_suspend,
+ .resume = omap_ehci_resume,
+ .runtime_suspend = omap_ehci_runtime_suspend,
+ .runtime_resume = omap_ehci_runtime_resume,
+};
+
static struct platform_driver ehci_hcd_omap_driver = {
.probe = ehci_hcd_omap_probe,
.remove = ehci_hcd_omap_remove,
.shutdown = ehci_hcd_omap_shutdown,
- /*.suspend = ehci_hcd_omap_suspend, */
- /*.resume = ehci_hcd_omap_resume, */
.driver = {
.name = hcd_name,
.of_match_table = omap_ehci_dt_ids,
+ .pm = &omap_ehci_pm_ops,
}
};
--
1.7.4.1
next prev parent reply other threads:[~2013-07-10 16:23 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-07-10 16:17 [PATCH 0/6] USB: Implement runtime idling and remote wakeup for OMAP EHCI controller Roger Quadros
2013-07-10 16:17 ` [PATCH 1/6] ARM: OMAP3: Enable Hardware Save and Restore for USB Host Roger Quadros
2013-07-10 16:22 ` [PATCH 2/6] ARM: dts: omap3beagle-xm: Add idle state pins for USB host Roger Quadros
2013-07-10 16:22 ` [PATCH 3/6] mfd: omap-usb-host: move initialization to module_init() Roger Quadros
2013-07-10 16:23 ` [PATCH 4/6] mfd: omap-usb-host: Put pins in IDLE state on suspend Roger Quadros
2013-07-14 13:22 ` Kevin Hilman
2013-07-15 8:23 ` Roger Quadros
2013-07-10 16:23 ` [PATCH 5/6] USB: Support wakeup IRQ for suspended controllers Roger Quadros
2013-07-10 18:45 ` Alan Stern
2013-07-11 7:30 ` Roger Quadros
2013-07-10 19:08 ` Alan Stern
2013-07-11 7:30 ` Roger Quadros
2013-07-10 16:23 ` Roger Quadros [this message]
2013-07-10 19:04 ` [PATCH 6/6] USB: ehci-omap: Implement suspend/resume Alan Stern
2013-07-11 8:50 ` Roger Quadros
[not found] ` <51DE71F3.1040101-l0cyMroinI0@public.gmane.org>
2013-07-11 15:14 ` Alan Stern
2013-07-22 13:16 ` Roger Quadros
2013-07-22 15:18 ` Alan Stern
2013-07-23 9:18 ` Roger Quadros
2013-07-23 14:14 ` Alan Stern
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1373473405-27589-1-git-send-email-rogerq@ti.com \
--to=rogerq@ti.com \
--cc=balbi@ti.com \
--cc=gregkh@linuxfoundation.org \
--cc=khilman@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=ruslan.bilovol@ti.com \
--cc=sergei.shtylyov@cogentembedded.com \
--cc=stern@rowland.harvard.edu \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox