From mboxrd@z Thu Jan 1 00:00:00 1970 From: Roger Quadros Subject: [PATCH v2 9/9] ARM: dts: omap3-beagle-xm: Add USB Host support Date: Thu, 15 Aug 2013 13:18:29 +0300 Message-ID: <1376561909-4406-10-git-send-email-rogerq@ti.com> References: <1376561909-4406-1-git-send-email-rogerq@ti.com> Mime-Version: 1.0 Content-Type: text/plain Return-path: In-Reply-To: <1376561909-4406-1-git-send-email-rogerq-l0cyMroinI0@public.gmane.org> Sender: linux-usb-owner-u79uwXL29TY76Z2rM5mHXA@public.gmane.org To: balbi-l0cyMroinI0@public.gmane.org, tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org, bcousson-rdvid1DuHRBWk0Htik3J/w@public.gmane.org Cc: p.zabel-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org, broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org, linux-usb-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-omap-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org, devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, Roger Quadros List-Id: linux-omap@vger.kernel.org Provide RESET GPIO and Power regulator for the USB PHY, the USB Host port mode and the PHY device for the controller. Also provide pin multiplexer information for USB host pins. We also relocate omap3_pmx_core pin definations so that they are close to omap3_pmx_wkup pin definations. Signed-off-by: Roger Quadros --- arch/arm/boot/dts/omap3-beagle-xm.dts | 65 ++++++++++++++++++++++++++++----- 1 files changed, 56 insertions(+), 9 deletions(-) diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts index afdb164..b081f5a 100644 --- a/arch/arm/boot/dts/omap3-beagle-xm.dts +++ b/arch/arm/boot/dts/omap3-beagle-xm.dts @@ -69,6 +69,23 @@ }; }; + + /* HS USB Port 2 Power */ + hsusb2_power: hsusb2_power_reg { + compatible = "regulator-fixed"; + regulator-name = "hsusb2_vbus"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&twl_gpio 18 0>; /* GPIO LEDA */ + startup-delay-us = <70000>; + }; + + /* HS USB Host PHY on PORT 2 */ + hsusb2_phy: hsusb2_phy { + compatible = "usb-nop-xceiv"; + reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>; /* gpio_147 */ + vcc-supply = <&hsusb2_power>; + }; }; &omap3_pmx_wkup { @@ -79,6 +96,37 @@ }; }; +&omap3_pmx_core { + pinctrl-names = "default"; + pinctrl-0 = < + &hsusbb2_pins + >; + + uart3_pins: pinmux_uart3_pins { + pinctrl-single,pins = < + 0x16e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ + 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx OUTPUT | MODE0 */ + >; + }; + + hsusbb2_pins: pinmux_hsusbb2_pins { + pinctrl-single,pins = < + 0x5c0 (PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */ + 0x5c2 (PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */ + 0x5c4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */ + 0x5c6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */ + 0x5c8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */ + 0x5cA (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */ + 0x1a4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */ + 0x1a6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */ + 0x1a8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */ + 0x1aa (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */ + 0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */ + 0x1ae (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */ + >; + }; +}; + &i2c1 { clock-frequency = <2600000>; @@ -148,15 +196,6 @@ power = <50>; }; -&omap3_pmx_core { - uart3_pins: pinmux_uart3_pins { - pinctrl-single,pins = < - 0x16e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ - 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx OUTPUT | MODE0 */ - >; - }; -};