From: Markus Pargmann <mpa@pengutronix.de>
To: "David S. Miller" <davem@davemloft.net>
Cc: "Benoît Cousson" <bcousson@baylibre.com>,
"Tony Lindgren" <tony@atomide.com>,
"Wolfram Sang" <wsa@the-dreams.de>,
"Steven Rostedt" <rostedt@goodmis.org>,
linux-omap@vger.kernel.org, devicetree@vger.kernel.org,
linux-arm-kernel@lists.infradead.org, kernel@pengutronix.de,
"Markus Pargmann" <mpa@pengutronix.de>
Subject: [PATCH v3 5/7] net: cpsw: Add am33xx MACID readout
Date: Sat, 16 Aug 2014 17:18:33 +0200 [thread overview]
Message-ID: <1408202315-20006-6-git-send-email-mpa@pengutronix.de> (raw)
In-Reply-To: <1408202315-20006-1-git-send-email-mpa@pengutronix.de>
This patch adds a function to get the MACIDs from the am33xx SoC
control module registers which hold unique vendor MACIDs. This is only
used if of_get_mac_address() fails to get a valid mac address.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
---
Documentation/devicetree/bindings/net/cpsw.txt | 4 +++
drivers/net/ethernet/ti/Kconfig | 2 ++
drivers/net/ethernet/ti/Makefile | 1 +
drivers/net/ethernet/ti/cpsw.c | 46 ++++++++++++++++++++++++--
4 files changed, 51 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt
index 107caf174a0e..33fe8462edf4 100644
--- a/Documentation/devicetree/bindings/net/cpsw.txt
+++ b/Documentation/devicetree/bindings/net/cpsw.txt
@@ -24,6 +24,8 @@ Optional properties:
- ti,hwmods : Must be "cpgmac0"
- no_bd_ram : Must be 0 or 1
- dual_emac : Specifies Switch to act as Dual EMAC
+- syscon : Phandle to the system control device node, which is
+ the control module device of the am33x
Slave Properties:
Required properties:
@@ -57,6 +59,7 @@ Examples:
active_slave = <0>;
cpts_clock_mult = <0x80000000>;
cpts_clock_shift = <29>;
+ syscon = <&cm>;
cpsw_emac0: slave@0 {
phy_id = <&davinci_mdio>, <0>;
phy-mode = "rgmii-txid";
@@ -85,6 +88,7 @@ Examples:
active_slave = <0>;
cpts_clock_mult = <0x80000000>;
cpts_clock_shift = <29>;
+ syscon = <&cm>;
cpsw_emac0: slave@0 {
phy_id = <&davinci_mdio>, <0>;
phy-mode = "rgmii-txid";
diff --git a/drivers/net/ethernet/ti/Kconfig b/drivers/net/ethernet/ti/Kconfig
index 53150c25a96b..afaf0196ffd2 100644
--- a/drivers/net/ethernet/ti/Kconfig
+++ b/drivers/net/ethernet/ti/Kconfig
@@ -62,6 +62,8 @@ config TI_CPSW
select TI_DAVINCI_CPDMA
select TI_DAVINCI_MDIO
select TI_CPSW_PHY_SEL
+ select MFD_SYSCON
+ select REGMAP
---help---
This driver supports TI's CPSW Ethernet Switch.
diff --git a/drivers/net/ethernet/ti/Makefile b/drivers/net/ethernet/ti/Makefile
index 9cfaab8152be..5a31c2b322ee 100644
--- a/drivers/net/ethernet/ti/Makefile
+++ b/drivers/net/ethernet/ti/Makefile
@@ -8,5 +8,6 @@ obj-$(CONFIG_TI_DAVINCI_EMAC) += davinci_emac.o
obj-$(CONFIG_TI_DAVINCI_MDIO) += davinci_mdio.o
obj-$(CONFIG_TI_DAVINCI_CPDMA) += davinci_cpdma.o
obj-$(CONFIG_TI_CPSW_PHY_SEL) += cpsw-phy-sel.o
+obj-$(CONFIG_TI_CPSW_CTRL_MACID) += cpsw-ctrl-macid.o
obj-$(CONFIG_TI_CPSW) += ti_cpsw.o
ti_cpsw-y := cpsw_ale.o cpsw.o cpts.o
diff --git a/drivers/net/ethernet/ti/cpsw.c b/drivers/net/ethernet/ti/cpsw.c
index b52df53441b0..aa13f68a178c 100644
--- a/drivers/net/ethernet/ti/cpsw.c
+++ b/drivers/net/ethernet/ti/cpsw.c
@@ -33,6 +33,8 @@
#include <linux/of_net.h>
#include <linux/of_device.h>
#include <linux/if_vlan.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
#include <linux/pinctrl/consumer.h>
@@ -1796,6 +1798,39 @@ static void cpsw_slave_init(struct cpsw_slave *slave, struct cpsw_priv *priv,
slave->port_vlan = data->dual_emac_res_vlan;
}
+#define AM33XX_CTRL_MAC_LO_REG(id) (0x630 + 0x8 * id)
+#define AM33XX_CTRL_MAC_HI_REG(id) (0x630 + 0x8 * id + 0x4)
+
+static int cpsw_am33xx_cm_get_macid(struct device *dev, int slave,
+ u8 *mac_addr)
+{
+ u32 macid_lo;
+ u32 macid_hi;
+ struct regmap *syscon;
+
+ if (!of_machine_is_compatible("ti,am33xx"))
+ return 0;
+
+ syscon = syscon_regmap_lookup_by_phandle(dev->of_node, "syscon");
+ if (IS_ERR(syscon)) {
+ if (PTR_ERR(syscon) == -ENODEV)
+ return 0;
+ return PTR_ERR(syscon);
+ }
+
+ regmap_read(syscon, AM33XX_CTRL_MAC_LO_REG(slave), &macid_lo);
+ regmap_read(syscon, AM33XX_CTRL_MAC_HI_REG(slave), &macid_hi);
+
+ mac_addr[5] = (macid_lo >> 8) & 0xff;
+ mac_addr[4] = macid_lo & 0xff;
+ mac_addr[3] = (macid_hi >> 24) & 0xff;
+ mac_addr[2] = (macid_hi >> 16) & 0xff;
+ mac_addr[1] = (macid_hi >> 8) & 0xff;
+ mac_addr[0] = macid_hi & 0xff;
+
+ return 0;
+}
+
static int cpsw_probe_dt(struct cpsw_platform_data *data,
struct platform_device *pdev)
{
@@ -1908,8 +1943,15 @@ static int cpsw_probe_dt(struct cpsw_platform_data *data,
PHY_ID_FMT, mdio->name, phyid);
mac_addr = of_get_mac_address(slave_node);
- if (mac_addr)
- memcpy(slave_data->mac_addr, mac_addr, ETH_ALEN);
+ if (mac_addr) {
+ memcpy(slave_data->mac_addr, mac_addr,
+ ETH_ALEN);
+ } else {
+ ret = cpsw_am33xx_cm_get_macid(&pdev->dev, i,
+ slave_data->mac_addr);
+ if (ret)
+ return ret;
+ }
slave_data->phy_if = of_get_phy_mode(slave_node);
if (slave_data->phy_if < 0) {
--
2.0.1
next prev parent reply other threads:[~2014-08-16 15:19 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-08-16 15:18 [PATCH v3 0/7] net: cpsw: Support for am335x chip MACIDs Markus Pargmann
2014-08-16 15:18 ` [PATCH v3 1/7] DT doc: net: cpsw mac-address is optional Markus Pargmann
2014-08-16 15:18 ` [PATCH v3 2/7] net: cpsw: Add missing return value Markus Pargmann
2014-08-16 15:18 ` [PATCH v3 3/7] net: cpsw: header, Add missing include Markus Pargmann
2014-08-16 15:18 ` [PATCH v3 4/7] net: cpsw: Replace pr_err by dev_err Markus Pargmann
2014-08-16 15:18 ` Markus Pargmann [this message]
2014-08-16 16:46 ` [PATCH v3 5/7] net: cpsw: Add am33xx MACID readout Wolfram Sang
2014-08-18 6:58 ` Markus Pargmann
2014-08-16 16:53 ` Wolfram Sang
2014-08-18 7:03 ` Markus Pargmann
2014-08-18 18:24 ` Mugunthan V N
2014-08-18 19:41 ` Steven Rostedt
2014-08-18 19:58 ` Mugunthan V N
2014-08-18 20:57 ` Steven Rostedt
2014-08-18 22:50 ` Javier Martinez Canillas
2014-08-19 8:50 ` Markus Pargmann
2014-08-19 16:37 ` Mugunthan V N
2014-08-16 15:18 ` [PATCH v3 6/7] am33xx: define syscon control module device node Markus Pargmann
2014-08-16 15:18 ` [PATCH v3 7/7] arm: dts: am33xx, Add syscon phandle to cpsw node Markus Pargmann
[not found] ` <1408202315-20006-1-git-send-email-mpa-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
2014-08-16 16:55 ` [PATCH v3 0/7] net: cpsw: Support for am335x chip MACIDs Wolfram Sang
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1408202315-20006-6-git-send-email-mpa@pengutronix.de \
--to=mpa@pengutronix.de \
--cc=bcousson@baylibre.com \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=kernel@pengutronix.de \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-omap@vger.kernel.org \
--cc=rostedt@goodmis.org \
--cc=tony@atomide.com \
--cc=wsa@the-dreams.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).