From: Sebastian Reichel <sre@kernel.org>
To: Sebastian Reichel <sre@kernel.org>,
Tony Lindgren <tony@atomide.com>,
Aaro Koskinen <aaro.koskinen@iki.fi>,
Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>,
David Airlie <airlied@linux.ie>,
linux-omap@vger.kernel.org, dri-devel@lists.freedesktop.org,
linux-kernel@vger.kernel.org
Subject: [PATCH 17/23] drm: omapdrm: panel-dsi-cm: add regulator support
Date: Tue, 8 Mar 2016 17:39:49 +0100 [thread overview]
Message-ID: <1457455195-1938-18-git-send-email-sre@kernel.org> (raw)
In-Reply-To: <1457455195-1938-1-git-send-email-sre@kernel.org>
The N950's display requires two regulators.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
---
drivers/gpu/drm/omapdrm/displays/panel-dsi-cm.c | 57 +++++++++++++++++++++++--
1 file changed, 53 insertions(+), 4 deletions(-)
diff --git a/drivers/gpu/drm/omapdrm/displays/panel-dsi-cm.c b/drivers/gpu/drm/omapdrm/displays/panel-dsi-cm.c
index 3414c2609320..768e92d1ec8b 100644
--- a/drivers/gpu/drm/omapdrm/displays/panel-dsi-cm.c
+++ b/drivers/gpu/drm/omapdrm/displays/panel-dsi-cm.c
@@ -24,6 +24,7 @@
#include <linux/workqueue.h>
#include <linux/of_device.h>
#include <linux/of_gpio.h>
+#include <linux/regulator/consumer.h>
#include <video/omapdss.h>
#include <video/omap-panel-data.h>
@@ -60,6 +61,9 @@ struct panel_drv_data {
int reset_gpio;
int ext_te_gpio;
+ struct regulator *vpnl;
+ struct regulator *vddi;
+
bool use_dsi_backlight;
struct omap_dsi_pin_config pin_config;
@@ -597,25 +601,43 @@ static int dsicm_power_on(struct panel_drv_data *ddata)
.lp_clk_max = 10000000,
};
+ if (ddata->vpnl) {
+ r = regulator_enable(ddata->vpnl);
+ if (r) {
+ dev_err(&ddata->pdev->dev,
+ "failed to enable VPNL: %d\n", r);
+ goto err0;
+ }
+ }
+
+ if (ddata->vddi) {
+ r = regulator_enable(ddata->vddi);
+ if (r) {
+ dev_err(&ddata->pdev->dev,
+ "failed to enable VDDI: %d\n", r);
+ goto err1;
+ }
+ }
+
if (ddata->pin_config.num_pins > 0) {
r = in->ops.dsi->configure_pins(in, &ddata->pin_config);
if (r) {
dev_err(&ddata->pdev->dev,
"failed to configure DSI pins\n");
- goto err0;
+ goto err2;
}
}
r = in->ops.dsi->set_config(in, &dsi_config);
if (r) {
dev_err(&ddata->pdev->dev, "failed to configure DSI\n");
- goto err0;
+ goto err2;
}
r = in->ops.dsi->enable(in);
if (r) {
dev_err(&ddata->pdev->dev, "failed to enable DSI\n");
- goto err0;
+ goto err2;
}
dsicm_hw_reset(ddata);
@@ -673,6 +695,12 @@ err:
dsicm_hw_reset(ddata);
in->ops.dsi->disable(in, true, false);
+err2:
+ if (ddata->vddi)
+ regulator_disable(ddata->vddi);
+err1:
+ if (ddata->vpnl)
+ regulator_disable(ddata->vpnl);
err0:
return r;
}
@@ -696,6 +724,11 @@ static void dsicm_power_off(struct panel_drv_data *ddata)
in->ops.dsi->disable(in, true, false);
+ if (ddata->vddi)
+ regulator_disable(ddata->vddi);
+ if (ddata->vpnl)
+ regulator_disable(ddata->vpnl);
+
ddata->enabled = 0;
}
@@ -1166,7 +1199,7 @@ static int dsicm_probe_of(struct platform_device *pdev)
struct device_node *node = pdev->dev.of_node;
struct panel_drv_data *ddata = platform_get_drvdata(pdev);
struct omap_dss_device *in;
- int gpio;
+ int gpio, err;
gpio = of_get_named_gpio(node, "reset-gpios", 0);
if (!gpio_is_valid(gpio)) {
@@ -1189,6 +1222,22 @@ static int dsicm_probe_of(struct platform_device *pdev)
return PTR_ERR(in);
}
+ ddata->vpnl = devm_regulator_get_optional(&pdev->dev, "vpnl");
+ if (IS_ERR(ddata->vpnl)) {
+ err = PTR_ERR(ddata->vpnl);
+ if (err == -EPROBE_DEFER)
+ return err;
+ ddata->vpnl = NULL;
+ }
+
+ ddata->vddi = devm_regulator_get_optional(&pdev->dev, "vddi");
+ if (IS_ERR(ddata->vddi)) {
+ err = PTR_ERR(ddata->vddi);
+ if (err == -EPROBE_DEFER)
+ return err;
+ ddata->vddi = NULL;
+ }
+
ddata->in = in;
/* TODO: ulps, backlight */
--
2.7.0
next prev parent reply other threads:[~2016-03-08 16:39 UTC|newest]
Thread overview: 64+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-03-08 16:39 [PATCH 00/23] Nokia N950 display support Sebastian Reichel
2016-03-08 16:39 ` [PATCH 01/23] ARM: dts: n9/n950: regulator configuration Sebastian Reichel
2016-03-08 16:39 ` [PATCH 02/23] ARM: dts: n950: add display support Sebastian Reichel
2016-03-17 12:14 ` Laurent Pinchart
2016-03-17 17:49 ` Sebastian Reichel
2016-03-23 12:40 ` Jani Nikula
2016-03-23 14:01 ` Sebastian Reichel
2016-03-24 10:03 ` Jani Nikula
2016-03-24 14:26 ` Sebastian Reichel
2016-03-24 15:11 ` Jani Nikula
2016-03-25 0:15 ` Sebastian Reichel
2016-04-12 20:51 ` Tony Lindgren
2016-06-21 11:01 ` Tony Lindgren
2016-06-24 0:30 ` Sebastian Reichel
2016-03-08 16:39 ` [PATCH 03/23] drm: omapdrm: dss: reset dsi module during initialization Sebastian Reichel
2016-05-10 12:07 ` Tomi Valkeinen
2016-03-08 16:39 ` [PATCH 04/23] drm: omapdrm: add DSI mapping Sebastian Reichel
2016-03-26 9:09 ` Laurent Pinchart
2016-05-10 12:08 ` Tomi Valkeinen
2016-03-08 16:39 ` [PATCH 05/23] Revert "drm: omapdrm: Remove manual update display support" Sebastian Reichel
2016-03-08 16:39 ` [PATCH 06/23] drm: omapdrm: wait for pending operations before updating plane Sebastian Reichel
2016-03-26 9:20 ` Laurent Pinchart
2016-03-26 15:52 ` Sebastian Reichel
2016-03-08 16:39 ` [PATCH 07/23] drm: omapdrm: crtc: switch pending variable to atomic bitset Sebastian Reichel
2016-03-26 16:30 ` Laurent Pinchart
2016-03-08 16:39 ` [PATCH 08/23] drm: omapdrm: crtc: add enabled bit to state Sebastian Reichel
2016-03-26 16:35 ` Laurent Pinchart
2016-03-08 16:39 ` [PATCH 09/23] drm: omapdrm: dss: method to get stallmode from lcd config Sebastian Reichel
2016-03-08 16:39 ` [PATCH 10/23] drm: omapdrm: crtc: detect manually updated displays Sebastian Reichel
2016-03-26 16:51 ` Laurent Pinchart
2016-03-08 16:39 ` [PATCH 11/23] include: video: omapdss: provide fifo threshold methods Sebastian Reichel
2016-03-26 16:44 ` Laurent Pinchart
2016-03-08 16:39 ` [PATCH 12/23] drm: omapdrm: plane: update fifo size on atomic update Sebastian Reichel
2016-12-13 17:35 ` Laurent Pinchart
2016-12-14 8:43 ` Tomi Valkeinen
2016-12-14 9:10 ` Laurent Pinchart
2016-12-14 9:14 ` Tomi Valkeinen
2016-12-14 14:03 ` Sebastian Reichel
2016-12-14 21:36 ` Laurent Pinchart
2016-12-15 8:40 ` Tomi Valkeinen
2016-03-08 16:39 ` [PATCH 13/23] drm: omapdrm: crtc: update plane fifos on lcd config change Sebastian Reichel
2016-03-26 17:00 ` Laurent Pinchart
2016-03-08 16:39 ` [PATCH 14/23] drm: omapdrm: crtc: save framedone callback from dss Sebastian Reichel
2016-03-26 17:03 ` Laurent Pinchart
2016-03-08 16:39 ` [PATCH 15/23] drm: omapdrm: crtc: add support for manual updated displays Sebastian Reichel
2016-03-08 16:39 ` [PATCH 16/23] drm: omapdrm: update manual displays on dirty ioctl Sebastian Reichel
2016-03-08 16:39 ` Sebastian Reichel [this message]
2016-03-08 16:39 ` [PATCH 18/23] drm: omapdrm: panel-dsi-cm: use threaded irq handler Sebastian Reichel
2016-05-10 12:19 ` Tomi Valkeinen
2016-03-08 16:39 ` [PATCH 19/23] drm: omapdrm: panel-dsi-cm: improve DT support Sebastian Reichel
2016-03-08 16:39 ` [PATCH 20/23] drm: omapdrm: panel-dsi-cm: add offset support Sebastian Reichel
2016-03-08 16:39 ` [PATCH 21/23] drm: omapdrm: panel-dsi-cm: block disable until update completed Sebastian Reichel
2016-03-08 16:39 ` [PATCH 22/23] drm: omapdrm: panel-dsi-cm: ratelimit debug output in update path Sebastian Reichel
2016-03-08 16:39 ` [PATCH 23/23] drm: omapdrm: panel-dsi-cm: provide timings methods for omapdrm Sebastian Reichel
2016-03-08 18:39 ` [PATCH 00/23] Nokia N950 display support Aaro Koskinen
2016-03-08 20:45 ` Sebastian Reichel
2016-03-09 7:10 ` Tomi Valkeinen
2016-03-09 14:33 ` Sebastian Reichel
2016-03-09 21:02 ` Aaro Koskinen
2016-03-09 16:19 ` Emil Velikov
2016-03-09 16:24 ` Tomi Valkeinen
2016-03-09 16:58 ` Emil Velikov
2016-03-09 17:09 ` Sebastian Reichel
2016-03-28 12:34 ` Emil Velikov
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1457455195-1938-18-git-send-email-sre@kernel.org \
--to=sre@kernel.org \
--cc=aaro.koskinen@iki.fi \
--cc=airlied@linux.ie \
--cc=dri-devel@lists.freedesktop.org \
--cc=laurent.pinchart@ideasonboard.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=tomi.valkeinen@ti.com \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).