From: Ladislav Michl <ladis@linux-mips.org>
To: Tony Lindgren <tony@atomide.com>
Cc: linux-omap-open-source@linux.omap.com
Subject: Re: Pending patches mostly pushed, please check
Date: Tue, 3 Jan 2006 21:41:35 +0100 [thread overview]
Message-ID: <20060103204135.GA11610@orphique> (raw)
In-Reply-To: <20060103191356.GR6034@atomide.com>
On Tue, Jan 03, 2006 at 11:13:56AM -0800, Tony Lindgren wrote:
> Hi all,
>
> I've pushed bunch of patches listed. Please check the status of
> your patches below.
>
> Also reply to this thread if you know if a patch that you think
> should be pushed and has not been pushed yet.
Umm, here is one more :-)
Remove support for board Netstar. I hope it helped to sort out various
needs to drivers and now when nearly everything [1] was converted to
platform device there is no more need to bother you with updates to
board file :-). I'll maintain it as separate patch (using PTXdist).
Thanks for all the fish :-)
Best regards,
ladis
[1] Oh, it seems USB host driver still contains those
machine_is_omap_xxx. Will fix that later...
diff --git a/arch/arm/mach-omap1/Kconfig b/arch/arm/mach-omap1/Kconfig
index a8d2d9a..f17b4ac 100644
--- a/arch/arm/mach-omap1/Kconfig
+++ b/arch/arm/mach-omap1/Kconfig
@@ -69,12 +69,6 @@ config MACH_VOICEBLUE
Support for Voiceblue GSM/VoIP gateway. Say Y here if you have
such a board.
-config MACH_NETSTAR
- bool "NetStar"
- depends on ARCH_OMAP1 && ARCH_OMAP15XX
- help
- Support for NetStar PBX. Say Y here if you have such a board.
-
config MACH_OMAP_PALMTE
bool "Palm Tungsten E"
depends on ARCH_OMAP1 && ARCH_OMAP15XX
diff --git a/arch/arm/mach-omap1/Makefile b/arch/arm/mach-omap1/Makefile
index 856fedf..fe6598d 100644
--- a/arch/arm/mach-omap1/Makefile
+++ b/arch/arm/mach-omap1/Makefile
@@ -20,7 +20,6 @@ obj-$(CONFIG_MACH_OMAP_PERSEUS2) += boar
obj-$(CONFIG_MACH_OMAP_OSK) += board-osk.o
obj-$(CONFIG_MACH_OMAP_H3) += board-h3.o
obj-$(CONFIG_MACH_VOICEBLUE) += board-voiceblue.o
-obj-$(CONFIG_MACH_NETSTAR) += board-netstar.o
obj-$(CONFIG_MACH_OMAP_PALMTE) += board-palmte.o
ifeq ($(CONFIG_ARCH_OMAP15XX),y)
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index cc31113..f4c4e8e 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -50,10 +50,10 @@ config MTD_NAND_SPIA
If you had to ask, you don't have one. Say 'N'.
config MTD_NAND_OMAP
- tristate "NAND Flash device on OMAP H3/H2/P2 or NETSTAR boards"
- depends on ARM && ARCH_OMAP1 && MTD_NAND && (MACH_OMAP_H2 || MACH_OMAP_H3 || MACH_NETSTAR || MACH_OMAP_PERSEUS2)
- help
- Support for NAND flash on Texas Instruments H3/H2/P2/NETSTAR platforms.
+ tristate "NAND Flash device on OMAP H3/H2/P2 boards"
+ depends on ARM && ARCH_OMAP1 && MTD_NAND && (MACH_OMAP_H2 || MACH_OMAP_H3 || MACH_OMAP_PERSEUS2)
+ help
+ Support for NAND flash on Texas Instruments H3/H2/P2 platforms.
config MTD_NAND_TOTO
tristate "NAND Flash device on TOTO board"
diff --git a/include/asm-arm/arch-omap/hardware.h b/include/asm-arm/arch-omap/hardware.h
index 5406b87..ecf5bae 100644
--- a/include/asm-arm/arch-omap/hardware.h
+++ b/include/asm-arm/arch-omap/hardware.h
@@ -314,10 +314,6 @@
#include "board-voiceblue.h"
#endif
-#ifdef CONFIG_MACH_NETSTAR
-#include "board-netstar.h"
-#endif
-
#endif /* !__ASSEMBLER__ */
#endif /* __ASM_ARCH_OMAP_HARDWARE_H */
--- a/include/asm-arm/arch-omap/board-netstar.h 2006-01-03 21:23:00.000000000 +0100
+++ b/include/asm-arm/arch-omap/board-netstar.h 2006-01-03 15:00:45.568894352 +0100
@@ -1,19 +0,0 @@
-/*
- * Copyright (C) 2004 2N Telekomunikace, Ladislav Michl <michl@2n.cz>
- *
- * Hardware definitions for OMAP5910 based NetStar board.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_NETSTAR_H
-#define __ASM_ARCH_NETSTAR_H
-
-#include <asm/arch/tc.h>
-
-#define OMAP_NAND_FLASH_START1 OMAP_CS1_PHYS + (1 << 23)
-#define OMAP_NAND_FLASH_START2 OMAP_CS1_PHYS + (2 << 23)
-
-#endif /* __ASM_ARCH_NETSTAR_H */
--- a/arch/arm/mach-omap1/board-netstar.c 2006-01-03 21:22:43.000000000 +0100
+++ b/arch/arm/mach-omap1/board-netstar.c 2006-01-03 15:00:45.568894352 +0100
@@ -1,160 +0,0 @@
-/*
- * Modified from board-generic.c
- *
- * Copyright (C) 2004 2N Telekomunikace, Ladislav Michl <michl@2n.cz>
- *
- * Code for Netstar OMAP board.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/delay.h>
-#include <linux/platform_device.h>
-#include <linux/interrupt.h>
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/notifier.h>
-#include <linux/reboot.h>
-
-#include <asm/hardware.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include <asm/arch/gpio.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/usb.h>
-#include <asm/arch/common.h>
-
-extern void __init omap_init_time(void);
-extern int omap_gpio_init(void);
-
-static struct resource netstar_smc91x_resources[] = {
- [0] = {
- .start = OMAP_CS1_PHYS + 0x300,
- .end = OMAP_CS1_PHYS + 0x300 + 16,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = OMAP_GPIO_IRQ(8),
- .end = OMAP_GPIO_IRQ(8),
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device netstar_smc91x_device = {
- .name = "smc91x",
- .id = 0,
- .num_resources = ARRAY_SIZE(netstar_smc91x_resources),
- .resource = netstar_smc91x_resources,
-};
-
-static struct platform_device *netstar_devices[] __initdata = {
- &netstar_smc91x_device,
-};
-
-static struct omap_uart_config netstar_uart_config __initdata = {
- .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
-};
-
-static struct omap_board_config_kernel netstar_config[] = {
- { OMAP_TAG_UART, &netstar_uart_config },
-};
-
-static void __init netstar_init_irq(void)
-{
- omap_init_irq();
- omap_gpio_init();
-}
-
-static void __init netstar_init(void)
-{
- /* green LED */
- omap_request_gpio(4);
- omap_set_gpio_direction(4, 0);
- /* smc91x reset */
- omap_request_gpio(7);
- omap_set_gpio_direction(7, 0);
- omap_set_gpio_dataout(7, 1);
- udelay(2); /* wait at least 100ns */
- omap_set_gpio_dataout(7, 0);
- mdelay(50); /* 50ms until PHY ready */
- /* smc91x interrupt pin */
- omap_request_gpio(8);
-
- omap_request_gpio(12);
- omap_request_gpio(13);
- omap_request_gpio(14);
- omap_request_gpio(15);
- set_irq_type(OMAP_GPIO_IRQ(12), IRQT_FALLING);
- set_irq_type(OMAP_GPIO_IRQ(13), IRQT_FALLING);
- set_irq_type(OMAP_GPIO_IRQ(14), IRQT_FALLING);
- set_irq_type(OMAP_GPIO_IRQ(15), IRQT_FALLING);
-
- platform_add_devices(netstar_devices, ARRAY_SIZE(netstar_devices));
-
- /* Switch on green LED */
- omap_set_gpio_dataout(4, 0);
- /* Switch off red LED */
- omap_writeb(0x00, OMAP_LPG1_PMR); /* Disable clock */
- omap_writeb(0x80, OMAP_LPG1_LCR);
-
- omap_board_config = netstar_config;
- omap_board_config_size = ARRAY_SIZE(netstar_config);
- omap_serial_init();
-}
-
-static void __init netstar_map_io(void)
-{
- omap_map_common_io();
-}
-
-#define MACHINE_PANICED 1
-#define MACHINE_REBOOTING 2
-#define MACHINE_REBOOT 4
-static unsigned long machine_state;
-
-static int panic_event(struct notifier_block *this, unsigned long event,
- void *ptr)
-{
- if (test_and_set_bit(MACHINE_PANICED, &machine_state))
- return NOTIFY_DONE;
-
- /* Switch off green LED */
- omap_set_gpio_dataout(4, 1);
- /* Flash red LED */
- omap_writeb(0x78, OMAP_LPG1_LCR);
- omap_writeb(0x01, OMAP_LPG1_PMR); /* Enable clock */
-
- return NOTIFY_DONE;
-}
-
-static struct notifier_block panic_block = {
- .notifier_call = panic_event,
-};
-
-static int __init netstar_late_init(void)
-{
- /* TODO: Setup front panel switch here */
-
- /* Setup panic notifier */
- notifier_chain_register(&panic_notifier_list, &panic_block);
-
- return 0;
-}
-
-postcore_initcall(netstar_late_init);
-
-MACHINE_START(NETSTAR, "NetStar OMAP5910")
- /* Maintainer: Ladislav Michl <michl@2n.cz> */
- .phys_ram = 0x10000000,
- .phys_io = 0xfff00000,
- .io_pg_offst = ((0xfef00000) >> 18) & 0xfffc,
- .boot_params = 0x10000100,
- .map_io = netstar_map_io,
- .init_irq = netstar_init_irq,
- .init_machine = netstar_init,
- .timer = &omap_timer,
-MACHINE_END
next prev parent reply other threads:[~2006-01-03 20:41 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-12-27 9:51 Pending patches Dirk Behme
2005-12-27 18:01 ` Anderson.Briglia
2005-12-28 15:53 ` Anderson Lizardo
2005-12-30 22:28 ` Tony Lindgren
2006-01-03 19:13 ` Pending patches mostly pushed, please check Tony Lindgren
2006-01-03 20:41 ` Ladislav Michl [this message]
2006-01-04 0:09 ` Tony Lindgren
2006-01-03 22:36 ` Todd Poynor
2006-01-04 0:27 ` Tony Lindgren
2006-01-04 0:25 ` Todd Poynor
2006-01-04 0:33 ` Tony Lindgren
2006-01-04 7:12 ` Komal Shah
2006-01-06 19:37 ` [PATCH] Convert touchscreen to input_allocate_device Dirk Behme
2006-01-14 0:18 ` Tony Lindgren
2006-01-06 19:37 ` [PATCH] Re: Pending patches mostly pushed, please check Dirk Behme
2006-01-14 0:20 ` Tony Lindgren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20060103204135.GA11610@orphique \
--to=ladis@linux-mips.org \
--cc=linux-omap-open-source@linux.omap.com \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox