Re: Git tree updated to 2.6.19-rc2

[David Brownell <david-b@pacbell.net>]

I measured it at "rc3", myself ... :)

Here's an update to the musb/tusb code fixing, among other things,
compile glitches that have recently joined us.  Like removing pt_regs
in all the IRQ paths, and a rename to <linux/usb/otg.h> ...

It's possible that (finally) removing the MIN_DMA_REQUEST thing would
make trouble; best way to test that is probably with g_file_storage.
If that fails, the obvious (temporary) workaround is disabling DMA.

- Dave


Various bugfixes:
    - gadget side does dma_sync_single_for_*() if the buffer
      was mapped by the gadget driver (none do that just yet)
    - host side rx, always force dma request off "just in case",
      instead of just for Mentor's DMA (i.e. not just OMAP2430)
    - complain louder about the board needing different driver config
    - iounmap() registers on rmmod
    - fault handling fixes in tusb_start()
    - (from TI) save dma mask so modprobe after use_dma=n can use dma
    - (from TI) gadget side zero-length IN likes TXPKTRDY before status stage

Other updates:
    - catch up to pt_regs finally leaving the irq path, other build fixes
    - remove pointless headers like <linux/pci.h>
    - RemoveMoreCamelCaseNastiness
    - resolve some config-specific compiler warning/error messages
    - dump tusb irq status register too
    - remove that MIN_DMA thing; dma logic must now handle zlps
      in all cases, not just to terminate a transfer
    - comment fixes

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

Index: h4/drivers/usb/musb/musbdefs.h
===================================================================
--- h4.orig/drivers/usb/musb/musbdefs.h	2006-10-25 22:24:14.000000000 -0700
+++ h4/drivers/usb/musb/musbdefs.h	2006-10-26 04:16:50.000000000 -0700
@@ -43,7 +43,7 @@
 #include <linux/usb_ch9.h>
 #include <linux/usb_gadget.h>
 #include <linux/usb.h>
-#include <linux/usb_otg.h>
+#include <linux/usb/otg.h>
 #include <linux/usb/musb.h>
 
 struct musb;
@@ -75,9 +75,6 @@ struct musb_ep;
 #include "otg.h"
 
 
-/* REVISIT tune this */
-#define	MIN_DMA_REQUEST		1	/* use PIO below this xfer size */
-
 
 #ifdef CONFIG_USB_MUSB_OTG
 
@@ -374,7 +371,7 @@ static inline struct usb_request *next_o
 struct musb {
 	spinlock_t		Lock;
 	struct clk		*clock;
-	irqreturn_t		(*isr)(int, void *, struct pt_regs *);
+	irqreturn_t		(*isr)(int, void *);
 	struct work_struct	irq_work;
 
 #ifdef CONFIG_USB_MUSB_HDRC_HCD
@@ -418,7 +415,6 @@ struct musb {
 	u8			int_usb;
 	u16			int_rx;
 	u16			int_tx;
-	struct pt_regs		*int_regs;
 
 	struct otg_transceiver	xceiv;
 
Index: h4/drivers/usb/musb/g_ep0.c
===================================================================
--- h4.orig/drivers/usb/musb/g_ep0.c	2006-10-25 22:24:14.000000000 -0700
+++ h4/drivers/usb/musb/g_ep0.c	2006-10-25 22:28:31.000000000 -0700
@@ -556,9 +556,11 @@ musb_read_setup(struct musb *pThis, stru
 	 */
 	pThis->bSetAddress = FALSE;
 	pThis->ackpend = MGC_M_CSR0_P_SVDRXPKTRDY;
-	if (req->wLength == 0)
+	if (req->wLength == 0) {
+		if (req->bRequestType & USB_DIR_IN)
+			pThis->ackpend |= MGC_M_CSR0_TXPKTRDY;
 		pThis->ep0_state = MGC_END0_STAGE_ACKWAIT;
-	else if (req->bRequestType & USB_DIR_IN) {
+	} else if (req->bRequestType & USB_DIR_IN) {
 		pThis->ep0_state = MGC_END0_STAGE_TX;
 		musb_writew(regs, MGC_O_HDRC_CSR0, MGC_M_CSR0_P_SVDRXPKTRDY);
 		while ((musb_readw(regs, MGC_O_HDRC_CSR0)
Index: h4/drivers/usb/musb/musb_gadget.h
===================================================================
--- h4.orig/drivers/usb/musb/musb_gadget.h	2006-10-25 22:24:14.000000000 -0700
+++ h4/drivers/usb/musb/musb_gadget.h	2006-10-25 22:28:31.000000000 -0700
@@ -74,6 +74,7 @@ struct musb_ep {
 	/* later things are modified based on usage */
 	struct list_head		req_list;
 
+	/* true if lock must be dropped but req_list may not be advanced */
 	u8				busy;
 };
 
Index: h4/drivers/usb/musb/musb_gadget.c
===================================================================
--- h4.orig/drivers/usb/musb/musb_gadget.c	2006-10-25 22:24:14.000000000 -0700
+++ h4/drivers/usb/musb/musb_gadget.c	2006-10-25 22:28:31.000000000 -0700
@@ -118,15 +118,23 @@ __acquires(ep->musb->Lock)
 
 	ep->busy = 1;
 	spin_unlock(&musb->Lock);
-	if (is_dma_capable() && req->mapped) {
-		dma_unmap_single(musb->controller,
-				req->request.dma,
-				req->request.length,
-				req->bTx
-					? DMA_TO_DEVICE
-					: DMA_FROM_DEVICE);
-		req->request.dma = DMA_ADDR_INVALID;
-		req->mapped = 0;
+	if (is_dma_capable()) {
+		if (req->mapped) {
+			dma_unmap_single(musb->controller,
+					req->request.dma,
+					req->request.length,
+					req->bTx
+						? DMA_TO_DEVICE
+						: DMA_FROM_DEVICE);
+			req->request.dma = DMA_ADDR_INVALID;
+			req->mapped = 0;
+		} else
+			dma_sync_single_for_cpu(musb->controller,
+					req->request.dma,
+					req->request.length,
+					req->bTx
+						? DMA_TO_DEVICE
+						: DMA_FROM_DEVICE);
 	}
 	if (pRequest->status == 0)
 		DBG(5, "%s done request %p,  %d/%d\n",
@@ -1135,7 +1143,7 @@ static int musb_gadget_queue(struct usb_
 {
 	struct musb_ep		*pEnd;
 	struct musb_request	*pRequest;
-	struct musb		*pThis;
+	struct musb		*musb;
 	int			status = 0;
 	unsigned long		lockflags;
 
@@ -1143,10 +1151,10 @@ static int musb_gadget_queue(struct usb_
 		return -EINVAL;
 
 	pEnd = to_musb_ep(ep);
-	pThis = pEnd->pThis;
+	musb = pEnd->pThis;
 
 	pRequest = to_musb_request(req);
-	pRequest->musb = pThis;
+	pRequest->musb = musb;
 
 	if (pRequest->ep != pEnd)
 		return -EINVAL;
@@ -1159,23 +1167,31 @@ static int musb_gadget_queue(struct usb_
 	pRequest->bEnd = pEnd->bEndNumber;
 	pRequest->bTx = pEnd->is_in;
 
-	if (is_dma_capable()
-			&& pRequest->request.dma == DMA_ADDR_INVALID
-			&& pRequest->request.length >= MIN_DMA_REQUEST
-			&& pEnd->dma) {
-		pRequest->request.dma = dma_map_single(pThis->controller,
-				pRequest->request.buf,
-				pRequest->request.length,
-				pRequest->bTx
-					? DMA_TO_DEVICE
-					: DMA_FROM_DEVICE);
-		pRequest->mapped = 1;
+	if (is_dma_capable() && pEnd->dma) {
+		if (pRequest->request.dma == DMA_ADDR_INVALID) {
+			pRequest->request.dma = dma_map_single(
+					musb->controller,
+					pRequest->request.buf,
+					pRequest->request.length,
+					pRequest->bTx
+						? DMA_TO_DEVICE
+						: DMA_FROM_DEVICE);
+			pRequest->mapped = 1;
+		} else {
+			dma_sync_single_for_device(musb->controller,
+					pRequest->request.dma,
+					pRequest->request.length,
+					pRequest->bTx
+						? DMA_TO_DEVICE
+						: DMA_FROM_DEVICE);
+			pRequest->mapped = 0;
+		}
 	} else if (!req->buf) {
 		return -ENODATA;
 	} else
 		pRequest->mapped = 0;
 
-	spin_lock_irqsave(&pThis->Lock, lockflags);
+	spin_lock_irqsave(&musb->Lock, lockflags);
 
 	/* don't queue if the ep is down */
 	if (!pEnd->desc) {
@@ -1190,10 +1206,10 @@ static int musb_gadget_queue(struct usb_
 
 	/* it this is the head of the queue, start i/o ... */
 	if (!pEnd->busy && &pRequest->request.list == pEnd->req_list.next)
-		musb_ep_restart(pThis, pRequest);
+		musb_ep_restart(musb, pRequest);
 
 cleanup:
-	spin_unlock_irqrestore(&pThis->Lock, lockflags);
+	spin_unlock_irqrestore(&musb->Lock, lockflags);
 	return status;
 }
 
Index: h4/drivers/usb/musb/musb_host.c
===================================================================
--- h4.orig/drivers/usb/musb/musb_host.c	2006-10-25 22:24:14.000000000 -0700
+++ h4/drivers/usb/musb/musb_host.c	2006-10-26 04:16:36.000000000 -0700
@@ -33,7 +33,6 @@
  ******************************************************************/
 
 #include <linux/module.h>
-#include <linux/pci.h>
 #include <linux/kernel.h>
 #include <linux/delay.h>
 #include <linux/sched.h>
@@ -284,7 +283,7 @@ __acquires(musb->Lock)
 			);
 
 	spin_unlock(&musb->Lock);
-	usb_hcd_giveback_urb(musb_to_hcd(musb), urb, musb->int_regs);
+	usb_hcd_giveback_urb(musb_to_hcd(musb), urb);
 	spin_lock(&musb->Lock);
 }
 
@@ -1485,8 +1484,8 @@ void musb_host_rx(struct musb *pThis, u8
 	}
 
 	if (unlikely(dma_channel_status(dma) == MGC_DMA_STATUS_BUSY)) {
-		/* SHOULD NEVER HAPPEN */
-		ERR("RX%d dma busy\n", bEnd);
+		/* SHOULD NEVER HAPPEN ... but at least DaVinci has done it */
+		ERR("RX%d dma busy, csr %04x\n", bEnd, wRxCsrVal);
 		goto finish;
 	}
 
@@ -1521,9 +1520,15 @@ void musb_host_rx(struct musb *pThis, u8
 	}
 #endif
 	if (dma && (wRxCsrVal & MGC_M_RXCSR_DMAENAB)) {
+		xfer_len = dma->dwActualLength;
+
+		wVal &= ~(MGC_M_RXCSR_DMAENAB
+			| MGC_M_RXCSR_H_AUTOREQ
+			| MGC_M_RXCSR_AUTOCLEAR
+			| MGC_M_RXCSR_RXPKTRDY);
+		musb_writew(pEnd->regs, MGC_O_HDRC_RXCSR, wVal);
 
 #ifdef CONFIG_USB_INVENTRA_DMA
-		xfer_len = dma->dwActualLength;
 		pUrb->actual_length += xfer_len;
 		qh->offset += xfer_len;
 
@@ -1531,14 +1536,6 @@ void musb_host_rx(struct musb *pThis, u8
 		bDone = (pUrb->actual_length >= pUrb->transfer_buffer_length)
 			|| (dma->dwActualLength & (qh->maxpacket - 1));
 
-		wVal &= ~(MGC_M_RXCSR_DMAENAB
-			| MGC_M_RXCSR_H_AUTOREQ
-			| MGC_M_RXCSR_AUTOCLEAR
-			| MGC_M_RXCSR_RXPKTRDY);
-
-		MGC_WriteCsr16(pBase, MGC_O_HDRC_RXCSR, bEnd, wVal);
-		MGC_WriteCsr16(pBase, MGC_O_HDRC_RXCSR, bEnd, wVal);
-
 		/* send IN token for next packet, without AUTOREQ */
 		if (!bDone) {
 			wVal |= MGC_M_RXCSR_H_REQPKT;
@@ -1552,7 +1549,6 @@ void musb_host_rx(struct musb *pThis, u8
 			MGC_ReadCsr16(pBase, MGC_O_HDRC_RXCOUNT, bEnd));
 #else
 		bDone = TRUE;
-		xfer_len = dma->dwActualLength;
 #endif
 	} else if (pUrb->status == -EINPROGRESS) {
 		/* if no errors, be sure a packet is ready for unloading */
@@ -1682,7 +1678,7 @@ static int musb_schedule(
 	int			idle;
 	int			wBestDiff;
 	int			nBestEnd, nEnd;
-	struct musb_hw_ep	*hw_ep;
+	struct musb_hw_ep	*hw_ep = NULL;
 	struct list_head	*head = NULL;
 
 	/* use fixed hardware for control and bulk */
Index: h4/drivers/usb/musb/plat_uds.c
===================================================================
--- h4.orig/drivers/usb/musb/plat_uds.c	2006-10-25 22:24:14.000000000 -0700
+++ h4/drivers/usb/musb/plat_uds.c	2006-10-26 04:23:29.000000000 -0700
@@ -94,7 +94,6 @@
  */
 
 #include <linux/module.h>
-#include <linux/pci.h>
 #include <linux/kernel.h>
 #include <linux/sched.h>
 #include <linux/slab.h>
@@ -665,6 +664,7 @@ void musb_start(struct musb *musb)
 	musb_writeb(regs, MGC_O_HDRC_POWER, MGC_M_POWER_ISOUPDATE
 						| MGC_M_POWER_SOFTCONN
 						| MGC_M_POWER_HSENAB
+						/* ENSUSPEND wedges tusb */
 						// | MGC_M_POWER_ENSUSPEND
 						);
 
@@ -672,7 +672,7 @@ void musb_start(struct musb *musb)
 	devctl = musb_readb(regs, MGC_O_HDRC_DEVCTL);
 	devctl &= ~MGC_M_DEVCTL_SESSION;
 
-	if (is_otg_enabled(pThis)) {
+	if (is_otg_enabled(musb)) {
 		/* session started after:
 		 * (a) ID-grounded irq, host mode;
 		 * (b) vbus present/connect IRQ, peripheral mode;
@@ -683,7 +683,7 @@ void musb_start(struct musb *musb)
 		else
 			devctl |= MGC_M_DEVCTL_SESSION;
 
-	} else if (is_host_enabled(pThis)) {
+	} else if (is_host_enabled(musb)) {
 		/* assume ID pin is hard-wired to ground */
 		devctl |= MGC_M_DEVCTL_SESSION;
 
@@ -1276,7 +1276,7 @@ static int __devinit musb_core_init(u16 
 
 #ifdef CONFIG_ARCH_OMAP243X
 
-static irqreturn_t generic_interrupt(int irq, void *__hci, struct pt_regs *r)
+static irqreturn_t generic_interrupt(int irq, void *__hci)
 {
 	unsigned long	flags;
 	irqreturn_t	retval = IRQ_NONE;
@@ -1287,7 +1287,6 @@ static irqreturn_t generic_interrupt(int
 	musb->int_usb = musb_readb(musb->pRegs, MGC_O_HDRC_INTRUSB);
 	musb->int_tx = musb_readw(musb->pRegs, MGC_O_HDRC_INTRTX);
 	musb->int_rx = musb_readw(musb->pRegs, MGC_O_HDRC_INTRRX);
-	musb->int_regs = r;
 
 	if (musb->int_usb || musb->int_tx || musb->int_rx)
 		retval = musb_interrupt(musb);
@@ -1604,7 +1603,6 @@ static void musb_free(struct musb *musb)
 	if (is_dma_capable() && musb->pDmaController) {
 		struct dma_controller	*c = musb->pDmaController;
 
-//
 		(void) c->stop(c->pPrivateData);
 		dma_controller_factory.destroy(c);
 	}
@@ -1667,7 +1665,7 @@ musb_init_controller(struct device *dev,
 	bad_config:
 #endif
 	default:
-		dev_dbg(dev, "incompatible Kconfig role setting\n");
+		dev_err(dev, "incompatible Kconfig role setting\n");
 		return -EINVAL;
 	}
 
@@ -1811,8 +1809,9 @@ fail:
 	INIT_WORK(&pThis->irq_work, musb_irq_work, pThis);
 
 #ifdef CONFIG_SYSFS
-	device_create_file(dev, &dev_attr_mode);
-	device_create_file(dev, &dev_attr_cable);
+	status = device_create_file(dev, &dev_attr_mode);
+	status = device_create_file(dev, &dev_attr_cable);
+	status = 0;
 #endif
 
 	return status;
@@ -1828,6 +1827,10 @@ fail2:
  * bridge to a platform device; this driver then suffices.
  */
 
+#ifndef CONFIG_USB_INVENTRA_FIFO
+static u64	*orig_dma_mask;
+#endif
+
 static int __devinit musb_probe(struct platform_device *pdev)
 {
 	struct device	*dev = &pdev->dev;
@@ -1845,12 +1848,17 @@ static int __devinit musb_probe(struct p
 		return -ENOMEM;
 	}
 
+#ifndef CONFIG_USB_INVENTRA_FIFO
+	/* clobbered by use_dma=n */
+	orig_dma_mask = dev->dma_mask;
+#endif
 	return musb_init_controller(dev, irq, base);
 }
 
 static int __devexit musb_remove(struct platform_device *pdev)
 {
 	struct musb	*musb = dev_to_musb(&pdev->dev);
+	void __iomem	*ctrl_base = musb->ctrl_base;
 
 	/* this gets called on rmmod.
 	 *  - Host mode: host may still be active
@@ -1864,7 +1872,11 @@ static int __devexit musb_remove(struct 
 		usb_remove_hcd(musb_to_hcd(musb));
 #endif
 	musb_free(musb);
+	iounmap(ctrl_base);
 	device_init_wakeup(&pdev->dev, 0);
+#ifndef CONFIG_USB_INVENTRA_FIFO
+	dev->dma_mask = orig_dma_mask;
+#endif
 	return 0;
 }
 
Index: h4/drivers/usb/musb/musb_procfs.c
===================================================================
--- h4.orig/drivers/usb/musb/musb_procfs.c	2006-10-25 22:24:14.000000000 -0700
+++ h4/drivers/usb/musb/musb_procfs.c	2006-10-25 22:28:31.000000000 -0700
@@ -558,7 +558,7 @@ static int dump_header_stats(struct musb
 	code = sprintf(buffer,
 			"TUSB6010: devconf %08x, phy enable %08x drive %08x"
 			"\n\totg %03x timer %08x"
-			"\n\tprcm conf %08x mgmt %08x; intmask %08x"
+			"\n\tprcm conf %08x mgmt %08x; int src %08x mask %08x"
 			"\n",
 			musb_readl(pThis->ctrl_base, TUSB_DEV_CONF),
 			musb_readl(pThis->ctrl_base, TUSB_PHY_OTG_CTRL_ENABLE),
@@ -567,6 +567,7 @@ static int dump_header_stats(struct musb
 			musb_readl(pThis->ctrl_base, TUSB_DEV_OTG_TIMER),
 			musb_readl(pThis->ctrl_base, TUSB_PRCM_CONF),
 			musb_readl(pThis->ctrl_base, TUSB_PRCM_MNGMT),
+			musb_readl(pThis->ctrl_base, TUSB_INT_SRC),
 			musb_readl(pThis->ctrl_base, TUSB_INT_MASK));
 	if (code <= 0)
 		goto done;
Index: h4/drivers/usb/musb/tusb6010.c
===================================================================
--- h4.orig/drivers/usb/musb/tusb6010.c	2006-10-25 22:24:14.000000000 -0700
+++ h4/drivers/usb/musb/tusb6010.c	2006-10-26 13:16:59.000000000 -0700
@@ -146,6 +146,7 @@ void musb_read_fifo(struct musb_hw_ep *h
  * at most mA current to be drawn from VBUS during a Default-B session
  * (that is, while VBUS exceeds 4.4V).  In Default-A (including pure host
  * mode), or low power Default-B sessions, something else supplies power.
+ * Caller must take care of locking.
  */
 static int tusb_set_power(struct otg_transceiver *x, unsigned mA)
 {
@@ -178,7 +179,7 @@ static int tusb_set_power(struct otg_tra
  * (to be fixed in rev3 silicon) ... symptoms include disconnect
  * or looping suspend/resume cycles
  */
-static void tusb_set_clock_source(struct musb *musb, int mode)
+static void tusb_set_clock_source(struct musb *musb, unsigned mode)
 {
 	void __iomem	*base = musb->ctrl_base;
 	u32		reg;
@@ -186,10 +187,17 @@ static void tusb_set_clock_source(struct
 	reg = musb_readl(base, TUSB_PRCM_CONF);
 	reg &= ~TUSB_PRCM_CONF_SYS_CLKSEL(0x3);
 
+	/* 0 = refclk (clkin, XI)
+	 * 1 = PHY 60 MHz (internal PLL)
+	 * 2 = not supported
+	 * 3 = NOR clock (huh?)
+	 */
 	if (mode > 0)
 		reg |= TUSB_PRCM_CONF_SYS_CLKSEL(mode & 0x3);
 
 	musb_writel(base, TUSB_PRCM_CONF, reg);
+
+	// FIXME tusb6010_platform_retime(mode == 0);
 }
 
 /*
@@ -477,7 +485,7 @@ tusb_otg_ints(struct musb *musb, u32 int
 	}
 }
 
-static irqreturn_t tusb_interrupt(int irq, void *__hci, struct pt_regs *r)
+static irqreturn_t tusb_interrupt(int irq, void *__hci)
 {
 	struct musb	*musb = __hci;
 	void __iomem	*base = musb->ctrl_base;
@@ -489,7 +497,6 @@ static irqreturn_t tusb_interrupt(int ir
 	int_src = musb_readl(base, TUSB_INT_SRC) & ~TUSB_INT_SRC_RESERVED_BITS;
 	DBG(3, "TUSB IRQ %08x\n", int_src);
 
-	musb->int_regs = r;
 	musb->int_usb = (u8) int_src;
 
 	/* Acknowledge wake-up source interrupts */
@@ -570,7 +577,6 @@ static irqreturn_t tusb_interrupt(int ir
 	musb_writel(base, TUSB_INT_SRC_CLEAR,
 		int_src & ~TUSB_INT_MASK_RESERVED_BITS);
 
-	musb->int_regs = NULL;
 	musb_platform_try_idle(musb);
 	spin_unlock_irqrestore(&musb->Lock, flags);
 
@@ -690,10 +696,10 @@ static int tusb_print_revision(struct mu
 	return TUSB_REV_MAJOR(musb_readl(base, TUSB_INT_CTRL_REV));
 }
 
-static int tusb_start(struct musb *musb)
+static int __devinit tusb_start(struct musb *musb)
 {
 	void __iomem	*base = musb->ctrl_base;
-	int		ret = -1;
+	int		ret = 0;
 	unsigned long	flags;
 	u32		reg;
 
@@ -701,7 +707,7 @@ static int tusb_start(struct musb *musb)
 		ret = musb->board_set_power(1);
 	if (ret != 0) {
 		printk(KERN_ERR "tusb: Cannot enable TUSB6010\n");
-		goto err;
+		return ret;
 	}
 
 	spin_lock_irqsave(&musb->Lock, flags);
@@ -752,6 +758,8 @@ static int tusb_start(struct musb *musb)
 	return 0;
 
 err:
+	spin_unlock_irqrestore(&musb->Lock, flags);
+
 	if (musb->board_set_power)
 		musb->board_set_power(0);
 
Index: h4/drivers/usb/musb/omap2430.c
===================================================================
--- h4.orig/drivers/usb/musb/omap2430.c	2006-10-25 22:24:14.000000000 -0700
+++ h4/drivers/usb/musb/omap2430.c	2006-10-25 22:28:31.000000000 -0700
@@ -21,7 +21,6 @@
  *
  */
 #include <linux/module.h>
-#include <linux/pci.h>
 #include <linux/kernel.h>
 #include <linux/sched.h>
 #include <linux/slab.h>
@@ -29,9 +28,6 @@
 #include <linux/list.h>
 #include <linux/clk.h>
 
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
 #include <asm/io.h>
 #include <asm/mach-types.h>
 #include <asm/arch/hardware.h>
Index: h4/drivers/usb/musb/davinci.c
===================================================================
--- h4.orig/drivers/usb/musb/davinci.c	2006-10-25 22:24:14.000000000 -0700
+++ h4/drivers/usb/musb/davinci.c	2006-10-26 04:18:04.000000000 -0700
@@ -22,7 +22,6 @@
  */
 
 #include <linux/module.h>
-#include <linux/pci.h>
 #include <linux/kernel.h>
 #include <linux/sched.h>
 #include <linux/slab.h>
@@ -246,7 +245,7 @@ static void davinci_set_vbus(struct musb
 	return davinci_vbus_power(musb, is_on, 0);
 }
 
-static irqreturn_t davinci_interrupt(int irq, void *__hci, struct pt_regs *r)
+static irqreturn_t davinci_interrupt(int irq, void *__hci)
 {
 	unsigned long	flags;
 	irqreturn_t	retval = IRQ_NONE;
@@ -289,7 +288,6 @@ static irqreturn_t davinci_interrupt(int
 			>> DAVINCI_USB_TXINT_SHIFT;
 	musb->int_usb = (tmp & DAVINCI_USB_USBINT_MASK)
 			>> DAVINCI_USB_USBINT_SHIFT;
-	musb->int_regs = r;
 
 	/* treat DRVVBUS irq like an ID change IRQ (for now) */
 	if (tmp & (1 << (8 + DAVINCI_USB_USBINT_SHIFT))) {
@@ -317,7 +315,6 @@ static irqreturn_t davinci_interrupt(int
 	/* irq stays asserted until EOI is written */
 	musb_writel(tibase, DAVINCI_USB_EOI_REG, 0);
 
-	musb->int_regs = NULL;
 	spin_unlock_irqrestore(&musb->Lock, flags);
 
 	/* REVISIT we sometimes get unhandled IRQs