* [PATCH 1/4] ARM: OMAP: re-organize duplicated 32k-timer code
2007-11-12 23:24 [PATCH 0/4] 32k timer reorg and sched_clock cleanup Kevin Hilman
@ 2007-11-12 23:24 ` Kevin Hilman
2007-11-12 23:24 ` [PATCH 2/4] ARM: OMAP: Move 32k-based sched_clock() to common code Kevin Hilman
` (2 subsequent siblings)
3 siblings, 0 replies; 11+ messages in thread
From: Kevin Hilman @ 2007-11-12 23:24 UTC (permalink / raw)
To: linux-omap-open-source
[-- Attachment #1: use-dmtimer-for-32k-timer.patch --]
[-- Type: text/plain, Size: 5815 bytes --]
On OMAP2/3, the gp-timer code can be used for a 32kHz timer simply by
setting the source to be the 32k clock instead of sys_clk.
This patch uses the mach-omap2/timer-gp.c code for 32kHz timer on
OMAP2, moving the logic into mach-omap2/timer-gp.c, and not using
plat-omap/timer32k.c which, for OMAP2, is redundant with the timer-gp
code.
Also, if CONFIG_OMAP_32K_TIMER is enabled, the gptimer-based
clocksource is not used. Instead the default 32k sync counter is used
as the clocksource (see the clocksource in plat-omap/common.c.) This
is important for sleep/suspend so there is a valid counter during
sleep. Note that the suspend/sleep code needs fixing to check for
overflows of this counter.
In addition, the OMAP2/3 details are removed from timer32k.c leaving
that with only OMAP1 specifics. A follow-up patch will move it from
plat-omap common code to mach-omap1.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
---
arch/arm/mach-omap2/Makefile | 4 ---
arch/arm/mach-omap2/timer-gp.c | 14 ++++++++++++
arch/arm/plat-omap/Makefile | 2 +
arch/arm/plat-omap/timer32k.c | 47 -----------------------------------------
4 files changed, 18 insertions(+), 49 deletions(-)
Index: dev/arch/arm/mach-omap2/Makefile
===================================================================
--- dev.orig/arch/arm/mach-omap2/Makefile
+++ dev/arch/arm/mach-omap2/Makefile
@@ -4,9 +4,7 @@
# Common support
obj-y := irq.o id.o io.o sram-fn.o memory.o prcm.o clock.o mux.o devices.o \
- serial.o gpmc.o
-
-obj-$(CONFIG_OMAP_MPU_TIMER) += timer-gp.o
+ serial.o gpmc.o timer-gp.o
# Power Management
obj-$(CONFIG_PM) += pm.o sleep.o
Index: dev/arch/arm/mach-omap2/timer-gp.c
===================================================================
--- dev.orig/arch/arm/mach-omap2/timer-gp.c
+++ dev/arch/arm/mach-omap2/timer-gp.c
@@ -104,7 +104,11 @@ static void __init omap2_gp_clockevent_i
gptimer = omap_dm_timer_request_specific(1);
BUG_ON(gptimer == NULL);
+#if defined(CONFIG_OMAP_32K_TIMER)
+ omap_dm_timer_set_source(gptimer, OMAP_TIMER_SRC_32_KHZ);
+#else
omap_dm_timer_set_source(gptimer, OMAP_TIMER_SRC_SYS_CLK);
+#endif
tick_rate = clk_get_rate(omap_dm_timer_get_fclk(gptimer));
omap2_gp_timer_irq.dev_id = (void *)gptimer;
@@ -122,6 +126,15 @@ static void __init omap2_gp_clockevent_i
clockevents_register_device(&clockevent_gpt);
}
+#ifdef CONFIG_OMAP_32K_TIMER
+/*
+ * When 32k-timer is enabled, don't use GPTimer for clocksource
+ * instead, just leave default clocksource which uses the 32k
+ * sync counter. See clocksource setup in see plat-omap/common.c.
+ */
+
+static inline void __init omap2_gp_clocksource_init(void) {}
+#else
/*
* clocksource
*/
@@ -167,6 +180,7 @@ static void __init omap2_gp_clocksource_
if (clocksource_register(&clocksource_gpt))
printk(err2, clocksource_gpt.name);
}
+#endif
static void __init omap2_gp_timer_init(void)
{
Index: dev/arch/arm/plat-omap/Makefile
===================================================================
--- dev.orig/arch/arm/plat-omap/Makefile
+++ dev/arch/arm/plat-omap/Makefile
@@ -9,7 +9,9 @@ obj-m :=
obj-n :=
obj- :=
+ifeq ($(CONFIG_ARCH_OMAP1),y)
obj-$(CONFIG_OMAP_32K_TIMER) += timer32k.o
+endif
# OCPI interconnect support for 1710, 1610 and 5912
obj-$(CONFIG_ARCH_OMAP16XX) += ocpi.o
Index: dev/arch/arm/plat-omap/timer32k.c
===================================================================
--- dev.orig/arch/arm/plat-omap/timer32k.c
+++ dev/arch/arm/plat-omap/timer32k.c
@@ -70,10 +70,6 @@ struct sys_timer omap_timer;
#if defined(CONFIG_ARCH_OMAP16XX)
#define TIMER_32K_SYNCHRONIZED 0xfffbc410
-#elif defined(CONFIG_ARCH_OMAP24XX)
-#define TIMER_32K_SYNCHRONIZED (OMAP2_32KSYNCT_BASE + 0x10)
-#elif defined(CONFIG_ARCH_OMAP34XX)
-#define TIMER_32K_SYNCHRONIZED 0x48320010
#else
#error OMAP 32KHz timer does not currently work on 15XX!
#endif
@@ -95,8 +91,6 @@ struct sys_timer omap_timer;
#define JIFFIES_TO_HW_TICKS(nr_jiffies, clock_rate) \
(((nr_jiffies) * (clock_rate)) / HZ)
-#if defined(CONFIG_ARCH_OMAP1)
-
static inline void omap_32k_timer_write(int val, int reg)
{
omap_writew(val, OMAP1_32K_TIMER_BASE + reg);
@@ -122,30 +116,6 @@ static inline void omap_32k_timer_stop(v
#define omap_32k_timer_ack_irq()
-#elif defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
-
-static struct omap_dm_timer *gptimer;
-
-static inline void omap_32k_timer_start(unsigned long load_val)
-{
- omap_dm_timer_set_load(gptimer, 1, 0xffffffff - load_val);
- omap_dm_timer_set_int_enable(gptimer, OMAP_TIMER_INT_OVERFLOW);
- omap_dm_timer_start(gptimer);
-}
-
-static inline void omap_32k_timer_stop(void)
-{
- omap_dm_timer_stop(gptimer);
-}
-
-static inline void omap_32k_timer_ack_irq(void)
-{
- u32 status = omap_dm_timer_read_status(gptimer);
- omap_dm_timer_write_status(gptimer, status);
-}
-
-#endif
-
static int omap_32k_timer_set_next_event(unsigned long delta,
struct clock_event_device *dev)
{
@@ -233,22 +203,7 @@ static struct irqaction omap_32k_timer_i
static __init void omap_init_32k_timer(void)
{
- if (cpu_class_is_omap1())
- setup_irq(INT_OS_TIMER, &omap_32k_timer_irq);
-
-#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
- /* REVISIT: Check 24xx TIOCP_CFG settings after idle works */
- if (cpu_class_is_omap2()) {
- gptimer = omap_dm_timer_request_specific(1);
- BUG_ON(gptimer == NULL);
-
- omap_dm_timer_set_source(gptimer, OMAP_TIMER_SRC_32_KHZ);
- setup_irq(omap_dm_timer_get_irq(gptimer), &omap_32k_timer_irq);
- omap_dm_timer_set_int_enable(gptimer,
- OMAP_TIMER_INT_CAPTURE | OMAP_TIMER_INT_OVERFLOW |
- OMAP_TIMER_INT_MATCH);
- }
-#endif
+ setup_irq(INT_OS_TIMER, &omap_32k_timer_irq);
clockevent_32k_timer.mult = div_sc(OMAP_32K_TICKS_PER_SEC,
NSEC_PER_SEC,
--
^ permalink raw reply [flat|nested] 11+ messages in thread* [PATCH 4/4] ARM: OMAP: Move timer32k to mach-omap1
2007-11-12 23:24 [PATCH 0/4] 32k timer reorg and sched_clock cleanup Kevin Hilman
` (2 preceding siblings ...)
2007-11-12 23:24 ` [PATCH 3/4] ARM: OMAP: Remove MPU-timer based sched_clock() Kevin Hilman
@ 2007-11-12 23:24 ` Kevin Hilman
3 siblings, 0 replies; 11+ messages in thread
From: Kevin Hilman @ 2007-11-12 23:24 UTC (permalink / raw)
To: linux-omap-open-source
[-- Attachment #1: move-timer32k-to-omap1.patch --]
[-- Type: text/plain, Size: 14364 bytes --]
Move now OMAP1-specific timer32k code to mach-omap1 since OMAP2/3 32k
timers are done in gptimer code.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
---
arch/arm/mach-omap1/Makefile | 3
arch/arm/mach-omap1/timer32k.c | 209 +++++++++++++++++++++++++++++++++++++++++
arch/arm/plat-omap/Makefile | 4
arch/arm/plat-omap/timer32k.c | 209 -----------------------------------------
4 files changed, 211 insertions(+), 214 deletions(-)
Index: dev/arch/arm/mach-omap1/Makefile
===================================================================
--- dev.orig/arch/arm/mach-omap1/Makefile
+++ dev/arch/arm/mach-omap1/Makefile
@@ -5,7 +5,8 @@
# Common support
obj-y := io.o id.o clock.o irq.o mux.o serial.o devices.o
-obj-$(CONFIG_OMAP_MPU_TIMER) += time.o
+obj-$(CONFIG_OMAP_MPU_TIMER) += time.o
+obj-$(CONFIG_OMAP_32K_TIMER) += timer32k.o
# Power Management
obj-$(CONFIG_PM) += pm.o sleep.o
Index: dev/arch/arm/mach-omap1/timer32k.c
===================================================================
--- /dev/null
+++ dev/arch/arm/mach-omap1/timer32k.c
@@ -0,0 +1,209 @@
+/*
+ * linux/arch/arm/plat-omap/timer32k.c
+ *
+ * OMAP 32K Timer
+ *
+ * Copyright (C) 2004 - 2005 Nokia Corporation
+ * Partial timer rewrite and additional dynamic tick timer support by
+ * Tony Lindgen <tony@atomide.com> and
+ * Tuukka Tikkanen <tuukka.tikkanen@elektrobit.com>
+ * OMAP Dual-mode timer framework support by Timo Teras
+ *
+ * MPU timer code based on the older MPU timer code for OMAP
+ * Copyright (C) 2000 RidgeRun, Inc.
+ * Author: Greg Lonnon <glonnon@ridgerun.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
+ * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
+ * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/sched.h>
+#include <linux/spinlock.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+#include <linux/clocksource.h>
+#include <linux/clockchips.h>
+
+#include <asm/system.h>
+#include <asm/hardware.h>
+#include <asm/io.h>
+#include <asm/leds.h>
+#include <asm/irq.h>
+#include <asm/mach/irq.h>
+#include <asm/mach/time.h>
+#include <asm/arch/dmtimer.h>
+
+struct sys_timer omap_timer;
+
+/*
+ * ---------------------------------------------------------------------------
+ * 32KHz OS timer
+ *
+ * This currently works only on 16xx, as 1510 does not have the continuous
+ * 32KHz synchronous timer. The 32KHz synchronous timer is used to keep track
+ * of time in addition to the 32KHz OS timer. Using only the 32KHz OS timer
+ * on 1510 would be possible, but the timer would not be as accurate as
+ * with the 32KHz synchronized timer.
+ * ---------------------------------------------------------------------------
+ */
+
+#if defined(CONFIG_ARCH_OMAP16XX)
+#define TIMER_32K_SYNCHRONIZED 0xfffbc410
+#else
+#error OMAP 32KHz timer does not currently work on 15XX!
+#endif
+
+/* 16xx specific defines */
+#define OMAP1_32K_TIMER_BASE 0xfffb9000
+#define OMAP1_32K_TIMER_CR 0x08
+#define OMAP1_32K_TIMER_TVR 0x00
+#define OMAP1_32K_TIMER_TCR 0x04
+
+#define OMAP_32K_TICKS_PER_SEC (32768)
+
+/*
+ * TRM says 1 / HZ = ( TVR + 1) / 32768, so TRV = (32768 / HZ) - 1
+ * so with HZ = 128, TVR = 255.
+ */
+#define OMAP_32K_TIMER_TICK_PERIOD ((OMAP_32K_TICKS_PER_SEC / HZ) - 1)
+
+#define JIFFIES_TO_HW_TICKS(nr_jiffies, clock_rate) \
+ (((nr_jiffies) * (clock_rate)) / HZ)
+
+static inline void omap_32k_timer_write(int val, int reg)
+{
+ omap_writew(val, OMAP1_32K_TIMER_BASE + reg);
+}
+
+static inline unsigned long omap_32k_timer_read(int reg)
+{
+ return omap_readl(OMAP1_32K_TIMER_BASE + reg) & 0xffffff;
+}
+
+static inline void omap_32k_timer_start(unsigned long load_val)
+{
+ if (!load_val)
+ load_val = 1;
+ omap_32k_timer_write(load_val, OMAP1_32K_TIMER_TVR);
+ omap_32k_timer_write(0x0f, OMAP1_32K_TIMER_CR);
+}
+
+static inline void omap_32k_timer_stop(void)
+{
+ omap_32k_timer_write(0x0, OMAP1_32K_TIMER_CR);
+}
+
+#define omap_32k_timer_ack_irq()
+
+static int omap_32k_timer_set_next_event(unsigned long delta,
+ struct clock_event_device *dev)
+{
+ omap_32k_timer_start(delta);
+
+ return 0;
+}
+
+static void omap_32k_timer_set_mode(enum clock_event_mode mode,
+ struct clock_event_device *evt)
+{
+ omap_32k_timer_stop();
+
+ switch (mode) {
+ case CLOCK_EVT_MODE_PERIODIC:
+ case CLOCK_EVT_MODE_ONESHOT:
+ omap_32k_timer_start(OMAP_32K_TIMER_TICK_PERIOD);
+ break;
+ case CLOCK_EVT_MODE_UNUSED:
+ case CLOCK_EVT_MODE_SHUTDOWN:
+ break;
+ case CLOCK_EVT_MODE_RESUME:
+ break;
+ }
+}
+
+static struct clock_event_device clockevent_32k_timer = {
+ .name = "32k-timer",
+ .features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,
+ .shift = 32,
+ .set_next_event = omap_32k_timer_set_next_event,
+ .set_mode = omap_32k_timer_set_mode,
+};
+
+/*
+ * The 32KHz synchronized timer is an additional timer on 16xx.
+ * It is always running.
+ */
+static inline unsigned long omap_32k_sync_timer_read(void)
+{
+ return omap_readl(TIMER_32K_SYNCHRONIZED);
+}
+
+static irqreturn_t omap_32k_timer_interrupt(int irq, void *dev_id)
+{
+ struct clock_event_device *evt = &clockevent_32k_timer;
+ omap_32k_timer_ack_irq();
+
+ evt->event_handler(evt);
+
+ return IRQ_HANDLED;
+}
+
+static struct irqaction omap_32k_timer_irq = {
+ .name = "32KHz timer",
+ .flags = IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL,
+ .handler = omap_32k_timer_interrupt,
+};
+
+static __init void omap_init_32k_timer(void)
+{
+ setup_irq(INT_OS_TIMER, &omap_32k_timer_irq);
+
+ clockevent_32k_timer.mult = div_sc(OMAP_32K_TICKS_PER_SEC,
+ NSEC_PER_SEC,
+ clockevent_32k_timer.shift);
+ clockevent_32k_timer.max_delta_ns =
+ clockevent_delta2ns(0xfffffffe, &clockevent_32k_timer);
+ clockevent_32k_timer.min_delta_ns =
+ clockevent_delta2ns(1, &clockevent_32k_timer);
+
+ clockevent_32k_timer.cpumask = cpumask_of_cpu(0);
+ clockevents_register_device(&clockevent_32k_timer);
+}
+
+/*
+ * ---------------------------------------------------------------------------
+ * Timer initialization
+ * ---------------------------------------------------------------------------
+ */
+static void __init omap_timer_init(void)
+{
+#ifdef CONFIG_OMAP_DM_TIMER
+ omap_dm_timer_init();
+#endif
+ omap_init_32k_timer();
+}
+
+struct sys_timer omap_timer = {
+ .init = omap_timer_init,
+};
Index: dev/arch/arm/plat-omap/Makefile
===================================================================
--- dev.orig/arch/arm/plat-omap/Makefile
+++ dev/arch/arm/plat-omap/Makefile
@@ -9,10 +9,6 @@ obj-m :=
obj-n :=
obj- :=
-ifeq ($(CONFIG_ARCH_OMAP1),y)
-obj-$(CONFIG_OMAP_32K_TIMER) += timer32k.o
-endif
-
# OCPI interconnect support for 1710, 1610 and 5912
obj-$(CONFIG_ARCH_OMAP16XX) += ocpi.o
Index: dev/arch/arm/plat-omap/timer32k.c
===================================================================
--- dev.orig/arch/arm/plat-omap/timer32k.c
+++ /dev/null
@@ -1,209 +0,0 @@
-/*
- * linux/arch/arm/plat-omap/timer32k.c
- *
- * OMAP 32K Timer
- *
- * Copyright (C) 2004 - 2005 Nokia Corporation
- * Partial timer rewrite and additional dynamic tick timer support by
- * Tony Lindgen <tony@atomide.com> and
- * Tuukka Tikkanen <tuukka.tikkanen@elektrobit.com>
- * OMAP Dual-mode timer framework support by Timo Teras
- *
- * MPU timer code based on the older MPU timer code for OMAP
- * Copyright (C) 2000 RidgeRun, Inc.
- * Author: Greg Lonnon <glonnon@ridgerun.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/interrupt.h>
-#include <linux/sched.h>
-#include <linux/spinlock.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/clocksource.h>
-#include <linux/clockchips.h>
-
-#include <asm/system.h>
-#include <asm/hardware.h>
-#include <asm/io.h>
-#include <asm/leds.h>
-#include <asm/irq.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/time.h>
-#include <asm/arch/dmtimer.h>
-
-struct sys_timer omap_timer;
-
-/*
- * ---------------------------------------------------------------------------
- * 32KHz OS timer
- *
- * This currently works only on 16xx, as 1510 does not have the continuous
- * 32KHz synchronous timer. The 32KHz synchronous timer is used to keep track
- * of time in addition to the 32KHz OS timer. Using only the 32KHz OS timer
- * on 1510 would be possible, but the timer would not be as accurate as
- * with the 32KHz synchronized timer.
- * ---------------------------------------------------------------------------
- */
-
-#if defined(CONFIG_ARCH_OMAP16XX)
-#define TIMER_32K_SYNCHRONIZED 0xfffbc410
-#else
-#error OMAP 32KHz timer does not currently work on 15XX!
-#endif
-
-/* 16xx specific defines */
-#define OMAP1_32K_TIMER_BASE 0xfffb9000
-#define OMAP1_32K_TIMER_CR 0x08
-#define OMAP1_32K_TIMER_TVR 0x00
-#define OMAP1_32K_TIMER_TCR 0x04
-
-#define OMAP_32K_TICKS_PER_SEC (32768)
-
-/*
- * TRM says 1 / HZ = ( TVR + 1) / 32768, so TRV = (32768 / HZ) - 1
- * so with HZ = 128, TVR = 255.
- */
-#define OMAP_32K_TIMER_TICK_PERIOD ((OMAP_32K_TICKS_PER_SEC / HZ) - 1)
-
-#define JIFFIES_TO_HW_TICKS(nr_jiffies, clock_rate) \
- (((nr_jiffies) * (clock_rate)) / HZ)
-
-static inline void omap_32k_timer_write(int val, int reg)
-{
- omap_writew(val, OMAP1_32K_TIMER_BASE + reg);
-}
-
-static inline unsigned long omap_32k_timer_read(int reg)
-{
- return omap_readl(OMAP1_32K_TIMER_BASE + reg) & 0xffffff;
-}
-
-static inline void omap_32k_timer_start(unsigned long load_val)
-{
- if (!load_val)
- load_val = 1;
- omap_32k_timer_write(load_val, OMAP1_32K_TIMER_TVR);
- omap_32k_timer_write(0x0f, OMAP1_32K_TIMER_CR);
-}
-
-static inline void omap_32k_timer_stop(void)
-{
- omap_32k_timer_write(0x0, OMAP1_32K_TIMER_CR);
-}
-
-#define omap_32k_timer_ack_irq()
-
-static int omap_32k_timer_set_next_event(unsigned long delta,
- struct clock_event_device *dev)
-{
- omap_32k_timer_start(delta);
-
- return 0;
-}
-
-static void omap_32k_timer_set_mode(enum clock_event_mode mode,
- struct clock_event_device *evt)
-{
- omap_32k_timer_stop();
-
- switch (mode) {
- case CLOCK_EVT_MODE_PERIODIC:
- case CLOCK_EVT_MODE_ONESHOT:
- omap_32k_timer_start(OMAP_32K_TIMER_TICK_PERIOD);
- break;
- case CLOCK_EVT_MODE_UNUSED:
- case CLOCK_EVT_MODE_SHUTDOWN:
- break;
- case CLOCK_EVT_MODE_RESUME:
- break;
- }
-}
-
-static struct clock_event_device clockevent_32k_timer = {
- .name = "32k-timer",
- .features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,
- .shift = 32,
- .set_next_event = omap_32k_timer_set_next_event,
- .set_mode = omap_32k_timer_set_mode,
-};
-
-/*
- * The 32KHz synchronized timer is an additional timer on 16xx.
- * It is always running.
- */
-static inline unsigned long omap_32k_sync_timer_read(void)
-{
- return omap_readl(TIMER_32K_SYNCHRONIZED);
-}
-
-static irqreturn_t omap_32k_timer_interrupt(int irq, void *dev_id)
-{
- struct clock_event_device *evt = &clockevent_32k_timer;
- omap_32k_timer_ack_irq();
-
- evt->event_handler(evt);
-
- return IRQ_HANDLED;
-}
-
-static struct irqaction omap_32k_timer_irq = {
- .name = "32KHz timer",
- .flags = IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL,
- .handler = omap_32k_timer_interrupt,
-};
-
-static __init void omap_init_32k_timer(void)
-{
- setup_irq(INT_OS_TIMER, &omap_32k_timer_irq);
-
- clockevent_32k_timer.mult = div_sc(OMAP_32K_TICKS_PER_SEC,
- NSEC_PER_SEC,
- clockevent_32k_timer.shift);
- clockevent_32k_timer.max_delta_ns =
- clockevent_delta2ns(0xfffffffe, &clockevent_32k_timer);
- clockevent_32k_timer.min_delta_ns =
- clockevent_delta2ns(1, &clockevent_32k_timer);
-
- clockevent_32k_timer.cpumask = cpumask_of_cpu(0);
- clockevents_register_device(&clockevent_32k_timer);
-}
-
-/*
- * ---------------------------------------------------------------------------
- * Timer initialization
- * ---------------------------------------------------------------------------
- */
-static void __init omap_timer_init(void)
-{
-#ifdef CONFIG_OMAP_DM_TIMER
- omap_dm_timer_init();
-#endif
- omap_init_32k_timer();
-}
-
-struct sys_timer omap_timer = {
- .init = omap_timer_init,
-};
--
^ permalink raw reply [flat|nested] 11+ messages in thread