From: Tony Lindgren <tony@atomide.com>
To: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-omap@vger.kernel.org, Chandra shekhar <x0044955@ti.com>,
Eduardo Valentin <eduardo.valentin@indt.org.br>
Subject: Re: [PATCH 1/4] PLAT-OMAP: MCBSP: Tranform into platform driver
Date: Tue, 20 May 2008 16:44:39 -0700 [thread overview]
Message-ID: <20080520234438.GR23002@atomide.com> (raw)
In-Reply-To: <1210022587-7756-2-git-send-email-edubezval@gmail.com>
[-- Attachment #1: Type: text/plain, Size: 37473 bytes --]
Hi,
Some comments below.
* Eduardo Valentin <edubezval@gmail.com> [080505 14:24]:
> From: Eduardo Valentin <eduardo.valentin@indt.org.br>
>
> This patch transform mcbsp code into a very initial
> implementation of a platform driver.
>
> It also gets ride of ifdefs on mcbsp.c code.
> To do it, a platform data structure was defined.
>
> Platform devices are located in arch/arm/plat-omap/devices.c
>
> Signed-off-by: Eduardo Valentin <eduardo.valentin@indt.org.br>
> ---
> arch/arm/plat-omap/devices.c | 45 +++
> arch/arm/plat-omap/mcbsp.c | 660 ++++++++++++++-----------------------
> include/asm-arm/arch-omap/mcbsp.h | 73 ++++-
> 3 files changed, 367 insertions(+), 411 deletions(-)
>
> diff --git a/arch/arm/plat-omap/devices.c b/arch/arm/plat-omap/devices.c
> index 099182b..b3e0147 100644
> --- a/arch/arm/plat-omap/devices.c
> +++ b/arch/arm/plat-omap/devices.c
> @@ -27,6 +27,7 @@
> #include <asm/arch/gpio.h>
> #include <asm/arch/menelaus.h>
> #include <asm/arch/dsp_common.h>
> +#include <asm/arch/mcbsp.h>
>
> #if defined(CONFIG_OMAP_DSP) || defined(CONFIG_OMAP_DSP_MODULE)
>
> @@ -150,6 +151,49 @@ static inline void omap_init_kp(void) {}
> #endif
>
> /*-------------------------------------------------------------------------*/
> +#if defined(CONFIG_OMAP_MCBSP) || defined(CONFIG_OMAP_MCBSP_MODULE)
> +
> +static struct platform_device omap_mcbsp_devices[OMAP_MAX_MCBSP_COUNT];
> +static int mcbsps_configured;
> +
> +void omap_mcbsp_register_board_cfg(struct omap_mcbsp_platform_data *config,
> + int size)
> +{
> + int i;
> +
> + if (size > OMAP_MAX_MCBSP_COUNT) {
> + printk(KERN_WARNING "Registered too many McBSPs platform_data."
> + " Using maximum (%d) available.\n",
> + OMAP_MAX_MCBSP_COUNT);
> + size = OMAP_MAX_MCBSP_COUNT;
> + }
> +
> + for (i = 0; i < size; i++) {
> + struct platform_device *new_mcbsp = &omap_mcbsp_devices[i];
> + new_mcbsp->name = "omap-mcbsp";
> + new_mcbsp->id = i + 1;
> + new_mcbsp->dev.platform_data = &config[i];
> + }
> + mcbsps_configured = size;
> +}
> +
> +static void __init omap_init_mcbsp(void)
> +{
> + int i;
> +
> + for (i = 0; i < mcbsps_configured; i++)
> + platform_device_register(&omap_mcbsp_devices[i]);
> +}
> +#else
> +void omap_mcbsp_register_board_cfg(struct omap_mcbsp_platform_data *config,
> + int size)
> +{ }
> +
> +static inline void __init omap_init_mcbsp(void)
> +{ }
> +#endif
> +
> +/*-------------------------------------------------------------------------*/
>
> #if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE) \
> || defined(CONFIG_MMC_OMAP_HS) || defined(CONFIG_MMC_OMAP_HS_MODULE)
> @@ -511,6 +555,7 @@ static int __init omap_init_devices(void)
> */
> omap_init_dsp();
> omap_init_kp();
> + omap_init_mcbsp();
> omap_init_mmc();
> omap_init_uwire();
> omap_init_wdt();
> diff --git a/arch/arm/plat-omap/mcbsp.c b/arch/arm/plat-omap/mcbsp.c
> index 053de31..5536223 100644
> --- a/arch/arm/plat-omap/mcbsp.c
> +++ b/arch/arm/plat-omap/mcbsp.c
> @@ -15,6 +15,7 @@
> #include <linux/module.h>
> #include <linux/init.h>
> #include <linux/device.h>
> +#include <linux/platform_device.h>
> #include <linux/wait.h>
> #include <linux/completion.h>
> #include <linux/interrupt.h>
> @@ -25,83 +26,53 @@
> #include <linux/irq.h>
>
> #include <asm/arch/dma.h>
> -#include <asm/arch/mux.h>
> -#include <asm/arch/irqs.h>
> -#include <asm/arch/dsp_common.h>
> #include <asm/arch/mcbsp.h>
>
> -#ifdef CONFIG_MCBSP_DEBUG
> -#define DBG(x...) printk(x)
> -#else
> -#define DBG(x...) do { } while (0)
> -#endif
> -
> -struct omap_mcbsp {
> - u32 io_base;
> - u8 id;
> - u8 free;
> - omap_mcbsp_word_length rx_word_length;
> - omap_mcbsp_word_length tx_word_length;
> -
> - omap_mcbsp_io_type_t io_type; /* IRQ or poll */
> - /* IRQ based TX/RX */
> - int rx_irq;
> - int tx_irq;
> -
> - /* DMA stuff */
> - u8 dma_rx_sync;
> - short dma_rx_lch;
> - u8 dma_tx_sync;
> - short dma_tx_lch;
> -
> - /* Completion queues */
> - struct completion tx_irq_completion;
> - struct completion rx_irq_completion;
> - struct completion tx_dma_completion;
> - struct completion rx_dma_completion;
> -
> - /* Protect the field .free, while checking if the mcbsp is in use */
> - spinlock_t lock;
> -};
> -
> static struct omap_mcbsp mcbsp[OMAP_MAX_MCBSP_COUNT];
> -#ifdef CONFIG_ARCH_OMAP1
> -static struct clk *mcbsp_dsp_ck;
> -static struct clk *mcbsp_api_ck;
> -static struct clk *mcbsp_dspxor_ck;
> -#endif
> -#ifdef CONFIG_ARCH_OMAP2
> -static struct clk *mcbsp1_ick;
> -static struct clk *mcbsp1_fck;
> -static struct clk *mcbsp2_ick;
> -static struct clk *mcbsp2_fck;
> -#endif
> +
> +#define omap_mcbsp_check_valid_id(id) (mcbsp[id].pdata && \
> + mcbsp[id].pdata->ops && \
> + mcbsp[id].pdata->ops->check && \
> + (mcbsp[id].pdata->ops->check(id) == 0))
>
> static void omap_mcbsp_dump_reg(u8 id)
> {
> - DBG("**** MCBSP%d regs ****\n", mcbsp[id].id);
> - DBG("DRR2: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, DRR2));
> - DBG("DRR1: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, DRR1));
> - DBG("DXR2: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, DXR2));
> - DBG("DXR1: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, DXR1));
> - DBG("SPCR2: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, SPCR2));
> - DBG("SPCR1: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, SPCR1));
> - DBG("RCR2: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, RCR2));
> - DBG("RCR1: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, RCR1));
> - DBG("XCR2: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, XCR2));
> - DBG("XCR1: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, XCR1));
> - DBG("SRGR2: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, SRGR2));
> - DBG("SRGR1: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, SRGR1));
> - DBG("PCR0: 0x%04x\n", OMAP_MCBSP_READ(mcbsp[id].io_base, PCR0));
> - DBG("***********************\n");
> + dev_dbg(mcbsp[id].dev, "**** McBSP%d regs ****\n", mcbsp[id].id);
> + dev_dbg(mcbsp[id].dev, "DRR2: 0x%04x\n",
> + OMAP_MCBSP_READ(mcbsp[id].io_base, DRR2));
> + dev_dbg(mcbsp[id].dev, "DRR1: 0x%04x\n",
> + OMAP_MCBSP_READ(mcbsp[id].io_base, DRR1));
> + dev_dbg(mcbsp[id].dev, "DXR2: 0x%04x\n",
> + OMAP_MCBSP_READ(mcbsp[id].io_base, DXR2));
> + dev_dbg(mcbsp[id].dev, "DXR1: 0x%04x\n",
> + OMAP_MCBSP_READ(mcbsp[id].io_base, DXR1));
> + dev_dbg(mcbsp[id].dev, "SPCR2: 0x%04x\n",
> + OMAP_MCBSP_READ(mcbsp[id].io_base, SPCR2));
> + dev_dbg(mcbsp[id].dev, "SPCR1: 0x%04x\n",
> + OMAP_MCBSP_READ(mcbsp[id].io_base, SPCR1));
> + dev_dbg(mcbsp[id].dev, "RCR2: 0x%04x\n",
> + OMAP_MCBSP_READ(mcbsp[id].io_base, RCR2));
> + dev_dbg(mcbsp[id].dev, "RCR1: 0x%04x\n",
> + OMAP_MCBSP_READ(mcbsp[id].io_base, RCR1));
> + dev_dbg(mcbsp[id].dev, "XCR2: 0x%04x\n",
> + OMAP_MCBSP_READ(mcbsp[id].io_base, XCR2));
> + dev_dbg(mcbsp[id].dev, "XCR1: 0x%04x\n",
> + OMAP_MCBSP_READ(mcbsp[id].io_base, XCR1));
> + dev_dbg(mcbsp[id].dev, "SRGR2: 0x%04x\n",
> + OMAP_MCBSP_READ(mcbsp[id].io_base, SRGR2));
> + dev_dbg(mcbsp[id].dev, "SRGR1: 0x%04x\n",
> + OMAP_MCBSP_READ(mcbsp[id].io_base, SRGR1));
> + dev_dbg(mcbsp[id].dev, "PCR0: 0x%04x\n",
> + OMAP_MCBSP_READ(mcbsp[id].io_base, PCR0));
> + dev_dbg(mcbsp[id].dev, "***********************\n");
> }
>
> static irqreturn_t omap_mcbsp_tx_irq_handler(int irq, void *dev_id)
> {
> struct omap_mcbsp *mcbsp_tx = dev_id;
>
> - DBG("TX IRQ callback : 0x%x\n",
> - OMAP_MCBSP_READ(mcbsp_tx->io_base, SPCR2));
> + dev_dbg(mcbsp_tx->dev, "TX IRQ callback : 0x%x\n",
> + OMAP_MCBSP_READ(mcbsp_tx->io_base, SPCR2));
>
> complete(&mcbsp_tx->tx_irq_completion);
>
> @@ -112,8 +83,8 @@ static irqreturn_t omap_mcbsp_rx_irq_handler(int irq, void *dev_id)
> {
> struct omap_mcbsp *mcbsp_rx = dev_id;
>
> - DBG("RX IRQ callback : 0x%x\n",
> - OMAP_MCBSP_READ(mcbsp_rx->io_base, SPCR2));
> + dev_dbg(mcbsp_rx->dev, "RX IRQ callback : 0x%x\n",
> + OMAP_MCBSP_READ(mcbsp_rx->io_base, SPCR2));
>
> complete(&mcbsp_rx->rx_irq_completion);
>
> @@ -124,8 +95,8 @@ static void omap_mcbsp_tx_dma_callback(int lch, u16 ch_status, void *data)
> {
> struct omap_mcbsp *mcbsp_dma_tx = data;
>
> - DBG("TX DMA callback : 0x%x\n",
> - OMAP_MCBSP_READ(mcbsp_dma_tx->io_base, SPCR2));
> + dev_dbg(mcbsp_dma_tx->dev, "TX DMA callback : 0x%x\n",
> + OMAP_MCBSP_READ(mcbsp_dma_tx->io_base, SPCR2));
>
> /* We can free the channels */
> omap_free_dma(mcbsp_dma_tx->dma_tx_lch);
> @@ -138,8 +109,8 @@ static void omap_mcbsp_rx_dma_callback(int lch, u16 ch_status, void *data)
> {
> struct omap_mcbsp *mcbsp_dma_rx = data;
>
> - DBG("RX DMA callback : 0x%x\n",
> - OMAP_MCBSP_READ(mcbsp_dma_rx->io_base, SPCR2));
> + dev_dbg(mcbsp_dma_rx->dev, "RX DMA callback : 0x%x\n",
> + OMAP_MCBSP_READ(mcbsp_dma_rx->io_base, SPCR2));
>
> /* We can free the channels */
> omap_free_dma(mcbsp_dma_rx->dma_rx_lch);
> @@ -156,9 +127,16 @@ static void omap_mcbsp_rx_dma_callback(int lch, u16 ch_status, void *data)
> */
> void omap_mcbsp_config(unsigned int id, const struct omap_mcbsp_reg_cfg *config)
> {
> - u32 io_base = mcbsp[id].io_base;
> + u32 io_base;
> +
> + if (!omap_mcbsp_check_valid_id(id)) {
> + printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
> + return;
> + }
>
> - DBG("OMAP-McBSP: McBSP%d io_base: 0x%8x\n", id + 1, io_base);
> + io_base = mcbsp[id].io_base;
> + dev_dbg(mcbsp[id].dev, "Configuring McBSP%d io_base: 0x%8x\n",
> + mcbsp[id].id, io_base);
>
> /* We write the given config */
> OMAP_MCBSP_WRITE(io_base, SPCR2, config->spcr2);
> @@ -175,97 +153,22 @@ void omap_mcbsp_config(unsigned int id, const struct omap_mcbsp_reg_cfg *config)
> }
> EXPORT_SYMBOL(omap_mcbsp_config);
>
> -static int omap_mcbsp_check(unsigned int id)
> -{
> - if (cpu_is_omap730()) {
> - if (id > OMAP_MAX_MCBSP_COUNT - 1) {
> - printk(KERN_ERR "OMAP-McBSP: McBSP%d doesn't exist\n",
> - id + 1);
> - return -1;
> - }
> - return 0;
> - }
> -
> - if (cpu_is_omap15xx() || cpu_is_omap16xx() || cpu_is_omap24xx()) {
> - if (id > OMAP_MAX_MCBSP_COUNT) {
> - printk(KERN_ERR "OMAP-McBSP: McBSP%d doesn't exist\n",
> - id + 1);
> - return -1;
> - }
> - return 0;
> - }
> -
> - return -1;
> -}
> -
> -#ifdef CONFIG_ARCH_OMAP1
> -static void omap_mcbsp_dsp_request(void)
> -{
> - if (cpu_is_omap15xx() || cpu_is_omap16xx()) {
> - int ret;
> -
> - ret = omap_dsp_request_mem();
> - if (ret < 0) {
> - printk(KERN_ERR "Could not get dsp memory: %i\n", ret);
> - return;
> - }
> -
> - clk_enable(mcbsp_dsp_ck);
> - clk_enable(mcbsp_api_ck);
> -
> - /* enable 12MHz clock to mcbsp 1 & 3 */
> - clk_enable(mcbsp_dspxor_ck);
> -
> - /*
> - * DSP external peripheral reset
> - * FIXME: This should be moved to dsp code
> - */
> - __raw_writew(__raw_readw(DSP_RSTCT2) | 1 | 1 << 1,
> - DSP_RSTCT2);
> - }
> -}
> -
> -static void omap_mcbsp_dsp_free(void)
> -{
> - if (cpu_is_omap15xx() || cpu_is_omap16xx()) {
> - omap_dsp_release_mem();
> - clk_disable(mcbsp_dspxor_ck);
> - clk_disable(mcbsp_dsp_ck);
> - clk_disable(mcbsp_api_ck);
> - }
> -}
> -#endif
> -
> -#ifdef CONFIG_ARCH_OMAP2
> -static void omap2_mcbsp2_mux_setup(void)
> -{
> - if (cpu_is_omap2420()) {
> - omap_cfg_reg(Y15_24XX_MCBSP2_CLKX);
> - omap_cfg_reg(R14_24XX_MCBSP2_FSX);
> - omap_cfg_reg(W15_24XX_MCBSP2_DR);
> - omap_cfg_reg(V15_24XX_MCBSP2_DX);
> - omap_cfg_reg(V14_24XX_GPIO117);
> - }
> - /*
> - * Need to add MUX settings for OMAP 2430 SDP
> - */
> -}
> -#endif
> -
> /*
> * We can choose between IRQ based or polled IO.
> * This needs to be called before omap_mcbsp_request().
> */
> int omap_mcbsp_set_io_type(unsigned int id, omap_mcbsp_io_type_t io_type)
> {
> - if (omap_mcbsp_check(id) < 0)
> - return -EINVAL;
> + if (!omap_mcbsp_check_valid_id(id)) {
> + printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
> + return -ENODEV;
> + }
>
> spin_lock(&mcbsp[id].lock);
>
> if (!mcbsp[id].free) {
> - printk(KERN_ERR "OMAP-McBSP: McBSP%d is currently in use\n",
> - id + 1);
> + dev_err(mcbsp[id].dev, "McBSP%d is currently in use\n",
> + mcbsp[id].id);
> spin_unlock(&mcbsp[id].lock);
> return -EINVAL;
> }
> @@ -282,34 +185,20 @@ int omap_mcbsp_request(unsigned int id)
> {
> int err;
>
> - if (omap_mcbsp_check(id) < 0)
> - return -EINVAL;
> -
> -#ifdef CONFIG_ARCH_OMAP1
> - /*
> - * On 1510, 1610 and 1710, McBSP1 and McBSP3
> - * are DSP public peripherals.
> - */
> - if (id == OMAP_MCBSP1 || id == OMAP_MCBSP3)
> - omap_mcbsp_dsp_request();
> -#endif
> -
> -#ifdef CONFIG_ARCH_OMAP2
> - if (cpu_is_omap24xx()) {
> - if (id == OMAP_MCBSP1) {
> - clk_enable(mcbsp1_ick);
> - clk_enable(mcbsp1_fck);
> - } else {
> - clk_enable(mcbsp2_ick);
> - clk_enable(mcbsp2_fck);
> - }
> + if (!omap_mcbsp_check_valid_id(id)) {
> + printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
> + return -ENODEV;
> }
> -#endif
> +
> + if (mcbsp[id].pdata->ops->request)
> + mcbsp[id].pdata->ops->request(id);
> +
> + mcbsp_clk_enable(&mcbsp[id]);
>
> spin_lock(&mcbsp[id].lock);
> if (!mcbsp[id].free) {
> - printk(KERN_ERR "OMAP-McBSP: McBSP%d is currently in use\n",
> - id + 1);
> + dev_err(mcbsp[id].dev, "McBSP%d is currently in use\n",
> + mcbsp[id].id);
> spin_unlock(&mcbsp[id].lock);
> return -1;
> }
> @@ -322,9 +211,9 @@ int omap_mcbsp_request(unsigned int id)
> err = request_irq(mcbsp[id].tx_irq, omap_mcbsp_tx_irq_handler,
> 0, "McBSP", (void *) (&mcbsp[id]));
> if (err != 0) {
> - printk(KERN_ERR "OMAP-McBSP: Unable to "
> - "request TX IRQ %d for McBSP%d\n",
> - mcbsp[id].tx_irq, mcbsp[id].id);
> + dev_err(mcbsp[id].dev, "Unable to request TX IRQ %d "
> + "for McBSP%d\n", mcbsp[id].tx_irq,
> + mcbsp[id].id);
> return err;
> }
>
> @@ -333,9 +222,9 @@ int omap_mcbsp_request(unsigned int id)
> err = request_irq(mcbsp[id].rx_irq, omap_mcbsp_rx_irq_handler,
> 0, "McBSP", (void *) (&mcbsp[id]));
> if (err != 0) {
> - printk(KERN_ERR "OMAP-McBSP: Unable to "
> - "request RX IRQ %d for McBSP%d\n",
> - mcbsp[id].rx_irq, mcbsp[id].id);
> + dev_err(mcbsp[id].dev, "Unable to request RX IRQ %d "
> + "for McBSP%d\n", mcbsp[id].rx_irq,
> + mcbsp[id].id);
> free_irq(mcbsp[id].tx_irq, (void *) (&mcbsp[id]));
> return err;
> }
> @@ -349,32 +238,20 @@ EXPORT_SYMBOL(omap_mcbsp_request);
>
> void omap_mcbsp_free(unsigned int id)
> {
> - if (omap_mcbsp_check(id) < 0)
> + if (!omap_mcbsp_check_valid_id(id)) {
> + printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
> return;
> -
> -#ifdef CONFIG_ARCH_OMAP1
> - if (cpu_class_is_omap1()) {
> - if (id == OMAP_MCBSP1 || id == OMAP_MCBSP3)
> - omap_mcbsp_dsp_free();
> }
> -#endif
> -
> -#ifdef CONFIG_ARCH_OMAP2
> - if (cpu_is_omap24xx()) {
> - if (id == OMAP_MCBSP1) {
> - clk_disable(mcbsp1_ick);
> - clk_disable(mcbsp1_fck);
> - } else {
> - clk_disable(mcbsp2_ick);
> - clk_disable(mcbsp2_fck);
> - }
> - }
> -#endif
> +
> + if (mcbsp[id].pdata->ops->free)
> + mcbsp[id].pdata->ops->free(id);
> +
> + mcbsp_clk_disable(&mcbsp[id]);
>
> spin_lock(&mcbsp[id].lock);
> if (mcbsp[id].free) {
> - printk(KERN_ERR "OMAP-McBSP: McBSP%d was not reserved\n",
> - id + 1);
> + dev_err(mcbsp[id].dev, "McBSP%d was not reserved\n",
> + mcbsp[id].id);
> spin_unlock(&mcbsp[id].lock);
> return;
> }
> @@ -400,8 +277,10 @@ void omap_mcbsp_start(unsigned int id)
> u32 io_base;
> u16 w;
>
> - if (omap_mcbsp_check(id) < 0)
> + if (!omap_mcbsp_check_valid_id(id)) {
> + printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
> return;
> + }
>
> io_base = mcbsp[id].io_base;
>
> @@ -435,8 +314,10 @@ void omap_mcbsp_stop(unsigned int id)
> u32 io_base;
> u16 w;
>
> - if (omap_mcbsp_check(id) < 0)
> + if (!omap_mcbsp_check_valid_id(id)) {
> + printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
> return;
> + }
>
> io_base = mcbsp[id].io_base;
>
> @@ -457,7 +338,14 @@ EXPORT_SYMBOL(omap_mcbsp_stop);
> /* polled mcbsp i/o operations */
> int omap_mcbsp_pollwrite(unsigned int id, u16 buf)
> {
> - u32 base = mcbsp[id].io_base;
> + u32 base;
> +
> + if (!omap_mcbsp_check_valid_id(id)) {
> + printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
> + return -ENODEV;
> + }
> +
> + base = mcbsp[id].io_base;
> writew(buf, base + OMAP_MCBSP_REG_DXR1);
> /* if frame sync error - clear the error */
> if (readw(base + OMAP_MCBSP_REG_SPCR2) & XSYNC_ERR) {
> @@ -479,8 +367,8 @@ int omap_mcbsp_pollwrite(unsigned int id, u16 buf)
> (XRST),
> base + OMAP_MCBSP_REG_SPCR2);
> udelay(10);
> - printk(KERN_ERR
> - " Could not write to McBSP Register\n");
> + dev_err(mcbsp[id].dev, "Could not write to"
> + " McBSP%d Register\n", mcbsp[id].id);
> return -2;
> }
> }
> @@ -492,7 +380,14 @@ EXPORT_SYMBOL(omap_mcbsp_pollwrite);
>
> int omap_mcbsp_pollread(unsigned int id, u16 *buf)
> {
> - u32 base = mcbsp[id].io_base;
> + u32 base;
> +
> + if (!omap_mcbsp_check_valid_id(id)) {
> + printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
> + return -ENODEV;
> + }
> +
> + base = mcbsp[id].io_base;
> /* if frame sync error - clear the error */
> if (readw(base + OMAP_MCBSP_REG_SPCR1) & RSYNC_ERR) {
> /* clear error */
> @@ -513,8 +408,8 @@ int omap_mcbsp_pollread(unsigned int id, u16 *buf)
> (RRST),
> base + OMAP_MCBSP_REG_SPCR1);
> udelay(10);
> - printk(KERN_ERR
> - " Could not read from McBSP Register\n");
> + dev_err(mcbsp[id].dev, "Could not read from"
> + " McBSP%d Register\n", mcbsp[id].id);
> return -2;
> }
> }
> @@ -531,12 +426,15 @@ EXPORT_SYMBOL(omap_mcbsp_pollread);
> void omap_mcbsp_xmit_word(unsigned int id, u32 word)
> {
> u32 io_base;
> - omap_mcbsp_word_length word_length = mcbsp[id].tx_word_length;
> + omap_mcbsp_word_length word_length;
>
> - if (omap_mcbsp_check(id) < 0)
> + if (!omap_mcbsp_check_valid_id(id)) {
> + printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
> return;
> + }
>
> io_base = mcbsp[id].io_base;
> + word_length = mcbsp[id].tx_word_length;
>
> wait_for_completion(&(mcbsp[id].tx_irq_completion));
>
> @@ -550,11 +448,14 @@ u32 omap_mcbsp_recv_word(unsigned int id)
> {
> u32 io_base;
> u16 word_lsb, word_msb = 0;
> - omap_mcbsp_word_length word_length = mcbsp[id].rx_word_length;
> + omap_mcbsp_word_length word_length;
>
> - if (omap_mcbsp_check(id) < 0)
> - return -EINVAL;
> + if (!omap_mcbsp_check_valid_id(id)) {
> + printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
> + return -ENODEV;
> + }
>
> + word_length = mcbsp[id].rx_word_length;
> io_base = mcbsp[id].io_base;
>
> wait_for_completion(&(mcbsp[id].rx_irq_completion));
> @@ -569,11 +470,20 @@ EXPORT_SYMBOL(omap_mcbsp_recv_word);
>
> int omap_mcbsp_spi_master_xmit_word_poll(unsigned int id, u32 word)
> {
> - u32 io_base = mcbsp[id].io_base;
> - omap_mcbsp_word_length tx_word_length = mcbsp[id].tx_word_length;
> - omap_mcbsp_word_length rx_word_length = mcbsp[id].rx_word_length;
> + u32 io_base;
> + omap_mcbsp_word_length tx_word_length;
> + omap_mcbsp_word_length rx_word_length;
> u16 spcr2, spcr1, attempts = 0, word_lsb, word_msb = 0;
>
> + if (!omap_mcbsp_check_valid_id(id)) {
> + printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
> + return -ENODEV;
> + }
> +
> + io_base = mcbsp[id].io_base;
> + tx_word_length = mcbsp[id].tx_word_length;
> + rx_word_length = mcbsp[id].rx_word_length;
> +
> if (tx_word_length != rx_word_length)
> return -EINVAL;
>
> @@ -587,7 +497,8 @@ int omap_mcbsp_spi_master_xmit_word_poll(unsigned int id, u32 word)
> udelay(10);
> OMAP_MCBSP_WRITE(io_base, SPCR2, spcr2 | XRST);
> udelay(10);
> - printk(KERN_ERR "McBSP transmitter not ready\n");
> + dev_err(mcbsp[id].dev, "McBSP%d transmitter not "
> + "ready\n", mcbsp[id].id);
> return -EAGAIN;
> }
> }
> @@ -607,7 +518,8 @@ int omap_mcbsp_spi_master_xmit_word_poll(unsigned int id, u32 word)
> udelay(10);
> OMAP_MCBSP_WRITE(io_base, SPCR1, spcr1 | RRST);
> udelay(10);
> - printk(KERN_ERR "McBSP receiver not ready\n");
> + dev_err(mcbsp[id].dev, "McBSP%d receiver not "
> + "ready\n", mcbsp[id].id);
> return -EAGAIN;
> }
> }
> @@ -623,11 +535,20 @@ EXPORT_SYMBOL(omap_mcbsp_spi_master_xmit_word_poll);
>
> int omap_mcbsp_spi_master_recv_word_poll(unsigned int id, u32 *word)
> {
> - u32 io_base = mcbsp[id].io_base, clock_word = 0;
> - omap_mcbsp_word_length tx_word_length = mcbsp[id].tx_word_length;
> - omap_mcbsp_word_length rx_word_length = mcbsp[id].rx_word_length;
> + u32 io_base, clock_word = 0;
> + omap_mcbsp_word_length tx_word_length;
> + omap_mcbsp_word_length rx_word_length;
> u16 spcr2, spcr1, attempts = 0, word_lsb, word_msb = 0;
>
> + if (!omap_mcbsp_check_valid_id(id)) {
> + printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
> + return -ENODEV;
> + }
> +
> + io_base = mcbsp[id].io_base;
> + tx_word_length = mcbsp[id].tx_word_length;
> + rx_word_length = mcbsp[id].rx_word_length;
> +
> if (tx_word_length != rx_word_length)
> return -EINVAL;
>
> @@ -641,7 +562,8 @@ int omap_mcbsp_spi_master_recv_word_poll(unsigned int id, u32 *word)
> udelay(10);
> OMAP_MCBSP_WRITE(io_base, SPCR2, spcr2 | XRST);
> udelay(10);
> - printk(KERN_ERR "McBSP transmitter not ready\n");
> + dev_err(mcbsp[id].dev, "McBSP%d transmitter not "
> + "ready\n", mcbsp[id].id);
> return -EAGAIN;
> }
> }
> @@ -661,7 +583,8 @@ int omap_mcbsp_spi_master_recv_word_poll(unsigned int id, u32 *word)
> udelay(10);
> OMAP_MCBSP_WRITE(io_base, SPCR1, spcr1 | RRST);
> udelay(10);
> - printk(KERN_ERR "McBSP receiver not ready\n");
> + dev_err(mcbsp[id].dev, "McBSP%d receiver not "
> + "ready\n", mcbsp[id].id);
> return -EAGAIN;
> }
> }
> @@ -692,20 +615,24 @@ int omap_mcbsp_xmit_buffer(unsigned int id, dma_addr_t buffer,
> int dest_port = 0;
> int sync_dev = 0;
>
> - if (omap_mcbsp_check(id) < 0)
> - return -EINVAL;
> + if (!omap_mcbsp_check_valid_id(id)) {
> + printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
> + return -ENODEV;
> + }
>
> if (omap_request_dma(mcbsp[id].dma_tx_sync, "McBSP TX",
> omap_mcbsp_tx_dma_callback,
> &mcbsp[id],
> &dma_tx_ch)) {
> - printk(KERN_ERR "OMAP-McBSP: Unable to request DMA channel for"
> - " McBSP%d TX. Trying IRQ based TX\n", id + 1);
> + dev_err(mcbsp[id].dev, " Unable to request DMA channel for "
> + "McBSP%d TX. Trying IRQ based TX\n",
> + mcbsp[id].id);
> return -EAGAIN;
> }
> mcbsp[id].dma_tx_lch = dma_tx_ch;
>
> - DBG("TX DMA on channel %d\n", dma_tx_ch);
> + dev_err(mcbsp[id].dev, "McBSP%d TX DMA on channel %d\n", mcbsp[id].id,
> + dma_tx_ch);
>
> init_completion(&(mcbsp[id].tx_dma_completion));
>
> @@ -713,7 +640,7 @@ int omap_mcbsp_xmit_buffer(unsigned int id, dma_addr_t buffer,
> src_port = OMAP_DMA_PORT_TIPB;
> dest_port = OMAP_DMA_PORT_EMIFF;
> }
> - if (cpu_is_omap24xx())
> + if (cpu_class_is_omap2())
> sync_dev = mcbsp[id].dma_tx_sync;
>
> omap_set_dma_transfer_params(mcbsp[id].dma_tx_lch,
> @@ -749,20 +676,24 @@ int omap_mcbsp_recv_buffer(unsigned int id, dma_addr_t buffer,
> int dest_port = 0;
> int sync_dev = 0;
>
> - if (omap_mcbsp_check(id) < 0)
> - return -EINVAL;
> + if (!omap_mcbsp_check_valid_id(id)) {
> + printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
> + return -ENODEV;
> + }
>
> if (omap_request_dma(mcbsp[id].dma_rx_sync, "McBSP RX",
> omap_mcbsp_rx_dma_callback,
> &mcbsp[id],
> &dma_rx_ch)) {
> - printk(KERN_ERR "Unable to request DMA channel for McBSP%d RX."
> - " Trying IRQ based RX\n", id + 1);
> + dev_err(mcbsp[id].dev, "Unable to request DMA channel for "
> + "McBSP%d RX. Trying IRQ based RX\n",
> + mcbsp[id].id);
> return -EAGAIN;
> }
> mcbsp[id].dma_rx_lch = dma_rx_ch;
>
> - DBG("RX DMA on channel %d\n", dma_rx_ch);
> + dev_err(mcbsp[id].dev, "McBSP%d RX DMA on channel %d\n", mcbsp[id].id,
> + dma_rx_ch);
>
> init_completion(&(mcbsp[id].rx_dma_completion));
>
> @@ -770,7 +701,7 @@ int omap_mcbsp_recv_buffer(unsigned int id, dma_addr_t buffer,
> src_port = OMAP_DMA_PORT_TIPB;
> dest_port = OMAP_DMA_PORT_EMIFF;
> }
> - if (cpu_is_omap24xx())
> + if (cpu_class_is_omap2())
> sync_dev = mcbsp[id].dma_rx_sync;
>
> omap_set_dma_transfer_params(mcbsp[id].dma_rx_lch,
> @@ -809,8 +740,10 @@ void omap_mcbsp_set_spi_mode(unsigned int id,
> {
> struct omap_mcbsp_reg_cfg mcbsp_cfg;
>
> - if (omap_mcbsp_check(id) < 0)
> + if (!omap_mcbsp_check_valid_id(id)) {
> + printk(KERN_ERR "%s: Invalid id (%d)\n", __func__, id + 1);
> return;
> + }
>
> memset(&mcbsp_cfg, 0, sizeof(struct omap_mcbsp_reg_cfg));
>
> @@ -871,182 +804,91 @@ EXPORT_SYMBOL(omap_mcbsp_set_spi_mode);
> * McBSP1 and McBSP3 are directly mapped on 1610 and 1510.
> * 730 has only 2 McBSP, and both of them are MPU peripherals.
> */
> -struct omap_mcbsp_info {
> - u32 virt_base;
> - u8 dma_rx_sync, dma_tx_sync;
> - u16 rx_irq, tx_irq;
> -};
> +static int __init omap_mcbsp_probe(struct platform_device *pdev)
> +{
> + struct omap_mcbsp_platform_data *pdata = pdev->dev.platform_data;
> + int id = pdev->id - 1;
> + int ret = 0;
> + int i;
>
> -#ifdef CONFIG_ARCH_OMAP730
> -static const struct omap_mcbsp_info mcbsp_730[] = {
> - [0] = { .virt_base = io_p2v(OMAP730_MCBSP1_BASE),
> - .dma_rx_sync = OMAP_DMA_MCBSP1_RX,
> - .dma_tx_sync = OMAP_DMA_MCBSP1_TX,
> - .rx_irq = INT_730_McBSP1RX,
> - .tx_irq = INT_730_McBSP1TX },
> - [1] = { .virt_base = io_p2v(OMAP730_MCBSP2_BASE),
> - .dma_rx_sync = OMAP_DMA_MCBSP3_RX,
> - .dma_tx_sync = OMAP_DMA_MCBSP3_TX,
> - .rx_irq = INT_730_McBSP2RX,
> - .tx_irq = INT_730_McBSP2TX },
> -};
> -#endif
> -
> -#ifdef CONFIG_ARCH_OMAP15XX
> -static const struct omap_mcbsp_info mcbsp_1510[] = {
> - [0] = { .virt_base = OMAP1510_MCBSP1_BASE,
> - .dma_rx_sync = OMAP_DMA_MCBSP1_RX,
> - .dma_tx_sync = OMAP_DMA_MCBSP1_TX,
> - .rx_irq = INT_McBSP1RX,
> - .tx_irq = INT_McBSP1TX },
> - [1] = { .virt_base = io_p2v(OMAP1510_MCBSP2_BASE),
> - .dma_rx_sync = OMAP_DMA_MCBSP2_RX,
> - .dma_tx_sync = OMAP_DMA_MCBSP2_TX,
> - .rx_irq = INT_1510_SPI_RX,
> - .tx_irq = INT_1510_SPI_TX },
> - [2] = { .virt_base = OMAP1510_MCBSP3_BASE,
> - .dma_rx_sync = OMAP_DMA_MCBSP3_RX,
> - .dma_tx_sync = OMAP_DMA_MCBSP3_TX,
> - .rx_irq = INT_McBSP3RX,
> - .tx_irq = INT_McBSP3TX },
> -};
> -#endif
> -
> -#if defined(CONFIG_ARCH_OMAP16XX)
> -static const struct omap_mcbsp_info mcbsp_1610[] = {
> - [0] = { .virt_base = OMAP1610_MCBSP1_BASE,
> - .dma_rx_sync = OMAP_DMA_MCBSP1_RX,
> - .dma_tx_sync = OMAP_DMA_MCBSP1_TX,
> - .rx_irq = INT_McBSP1RX,
> - .tx_irq = INT_McBSP1TX },
> - [1] = { .virt_base = io_p2v(OMAP1610_MCBSP2_BASE),
> - .dma_rx_sync = OMAP_DMA_MCBSP2_RX,
> - .dma_tx_sync = OMAP_DMA_MCBSP2_TX,
> - .rx_irq = INT_1610_McBSP2_RX,
> - .tx_irq = INT_1610_McBSP2_TX },
> - [2] = { .virt_base = OMAP1610_MCBSP3_BASE,
> - .dma_rx_sync = OMAP_DMA_MCBSP3_RX,
> - .dma_tx_sync = OMAP_DMA_MCBSP3_TX,
> - .rx_irq = INT_McBSP3RX,
> - .tx_irq = INT_McBSP3TX },
> -};
> -#endif
> -
> -#if defined(CONFIG_ARCH_OMAP24XX)
> -static const struct omap_mcbsp_info mcbsp_24xx[] = {
> - [0] = { .virt_base = IO_ADDRESS(OMAP24XX_MCBSP1_BASE),
> - .dma_rx_sync = OMAP24XX_DMA_MCBSP1_RX,
> - .dma_tx_sync = OMAP24XX_DMA_MCBSP1_TX,
> - .rx_irq = INT_24XX_MCBSP1_IRQ_RX,
> - .tx_irq = INT_24XX_MCBSP1_IRQ_TX,
> - },
> - [1] = { .virt_base = IO_ADDRESS(OMAP24XX_MCBSP2_BASE),
> - .dma_rx_sync = OMAP24XX_DMA_MCBSP2_RX,
> - .dma_tx_sync = OMAP24XX_DMA_MCBSP2_TX,
> - .rx_irq = INT_24XX_MCBSP2_IRQ_RX,
> - .tx_irq = INT_24XX_MCBSP2_IRQ_TX,
> - },
> -};
> -#endif
> + if (!pdata) {
> + dev_err(&pdev->dev, "McBSP device initialized without"
> + "platform data\n");
> + ret = -EINVAL;
> + goto exit;
> + }
>
> -static int __init omap_mcbsp_init(void)
> + dev_dbg(&pdev->dev, "Initializing OMAP McBSP (%d).\n", pdev->id);
> +
> + if (id >= OMAP_MAX_MCBSP_COUNT) {
> + dev_err(&pdev->dev, "Invalid McBSP device id (%d)\n", id);
> + ret = -EINVAL;
> + goto exit;
> + }
> +
> + spin_lock_init(&mcbsp[id].lock);
> + mcbsp[id].id = id + 1;
> + mcbsp[id].free = 1;
> + mcbsp[id].dma_tx_lch = -1;
> + mcbsp[id].dma_rx_lch = -1;
> +
> + mcbsp[id].io_base = pdata->virt_base;
> + /* Default I/O is IRQ based */
> + mcbsp[id].io_type = OMAP_MCBSP_IRQ_IO;
> + mcbsp[id].tx_irq = pdata->tx_irq;
> + mcbsp[id].rx_irq = pdata->rx_irq;
> + mcbsp[id].dma_rx_sync = pdata->dma_rx_sync;
> + mcbsp[id].dma_tx_sync = pdata->dma_tx_sync;
> +
> + mcbsp[id].nr_clocks = ARRAY_SIZE(pdata->clocks);
> + for (i = 0; i < ARRAY_SIZE(pdata->clocks); i++)
> + mcbsp[id].clocks[i] = clk_get(&pdev->dev, pdata->clocks[i]);
> +
You need to check for the errors with clk_get here. Also, I needed the
attached patch to keep asoc working on 24xx.
In general, how about create a custom clock for each mcbsp that handles
all the other clocks? That way you can have just one struct clk * for
each mcbsp and you can use standard clk_enable/disable calls instead
of the hard to read macros.
You can add the custom clocks to clock fwk with clk_register() during
the omap specific mcbsp init depending on which mcbsp's are in use
from board-*.c files. Then the custom clock defines it's own
enable/disable function that just calls the clk_enable/disable on the
right mcbsp clocks.
> + mcbsp[id].pdata = pdata;
> + mcbsp[id].dev = &pdev->dev;
> + platform_set_drvdata(pdev, &mcbsp[id]);
> +
> +exit:
> + return ret;
> +}
> +
> +static int omap_mcbsp_remove(struct platform_device *pdev)
> {
> - int mcbsp_count = 0, i;
> - static const struct omap_mcbsp_info *mcbsp_info;
> + struct omap_mcbsp *mcbsp = platform_get_drvdata(pdev);
>
> - printk(KERN_INFO "Initializing OMAP McBSP system\n");
> + platform_set_drvdata(pdev, NULL);
> + if (mcbsp) {
> + int i;
>
> -#ifdef CONFIG_ARCH_OMAP1
> - mcbsp_dsp_ck = clk_get(0, "dsp_ck");
> - if (IS_ERR(mcbsp_dsp_ck)) {
> - printk(KERN_ERR "mcbsp: could not acquire dsp_ck handle.\n");
> - return PTR_ERR(mcbsp_dsp_ck);
> - }
> - mcbsp_api_ck = clk_get(0, "api_ck");
> - if (IS_ERR(mcbsp_api_ck)) {
> - printk(KERN_ERR "mcbsp: could not acquire api_ck handle.\n");
> - return PTR_ERR(mcbsp_api_ck);
> - }
> - mcbsp_dspxor_ck = clk_get(0, "dspxor_ck");
> - if (IS_ERR(mcbsp_dspxor_ck)) {
> - printk(KERN_ERR "mcbsp: could not acquire dspxor_ck handle.\n");
> - return PTR_ERR(mcbsp_dspxor_ck);
> - }
> -#endif
> -#ifdef CONFIG_ARCH_OMAP2
> - mcbsp1_ick = clk_get(0, "mcbsp1_ick");
> - if (IS_ERR(mcbsp1_ick)) {
> - printk(KERN_ERR "mcbsp: could not acquire "
> - "mcbsp1_ick handle.\n");
> - return PTR_ERR(mcbsp1_ick);
> - }
> - mcbsp1_fck = clk_get(0, "mcbsp1_fck");
> - if (IS_ERR(mcbsp1_fck)) {
> - printk(KERN_ERR "mcbsp: could not acquire "
> - "mcbsp1_fck handle.\n");
> - return PTR_ERR(mcbsp1_fck);
> - }
> - mcbsp2_ick = clk_get(0, "mcbsp2_ick");
> - if (IS_ERR(mcbsp2_ick)) {
> - printk(KERN_ERR "mcbsp: could not acquire "
> - "mcbsp2_ick handle.\n");
> - return PTR_ERR(mcbsp2_ick);
> - }
> - mcbsp2_fck = clk_get(0, "mcbsp2_fck");
> - if (IS_ERR(mcbsp2_fck)) {
> - printk(KERN_ERR "mcbsp: could not acquire "
> - "mcbsp2_fck handle.\n");
> - return PTR_ERR(mcbsp2_fck);
> - }
> -#endif
> + if (mcbsp->pdata && mcbsp->pdata->ops &&
> + mcbsp->pdata->ops->free)
> + mcbsp->pdata->ops->free(mcbsp->id);
>
> -#ifdef CONFIG_ARCH_OMAP730
> - if (cpu_is_omap730()) {
> - mcbsp_info = mcbsp_730;
> - mcbsp_count = ARRAY_SIZE(mcbsp_730);
> - }
> -#endif
> -#ifdef CONFIG_ARCH_OMAP15XX
> - if (cpu_is_omap15xx()) {
> - mcbsp_info = mcbsp_1510;
> - mcbsp_count = ARRAY_SIZE(mcbsp_1510);
> - }
> -#endif
> -#if defined(CONFIG_ARCH_OMAP16XX)
> - if (cpu_is_omap16xx()) {
> - mcbsp_info = mcbsp_1610;
> - mcbsp_count = ARRAY_SIZE(mcbsp_1610);
> - }
> -#endif
> -#if defined(CONFIG_ARCH_OMAP24XX)
> - if (cpu_is_omap24xx()) {
> - mcbsp_info = mcbsp_24xx;
> - mcbsp_count = ARRAY_SIZE(mcbsp_24xx);
> - omap2_mcbsp2_mux_setup();
> - }
> -#endif
> - for (i = 0; i < OMAP_MAX_MCBSP_COUNT ; i++) {
> - if (i >= mcbsp_count) {
> - mcbsp[i].io_base = 0;
> - mcbsp[i].free = 0;
> - continue;
> - }
> - mcbsp[i].id = i + 1;
> - mcbsp[i].free = 1;
> - mcbsp[i].dma_tx_lch = -1;
> - mcbsp[i].dma_rx_lch = -1;
> -
> - mcbsp[i].io_base = mcbsp_info[i].virt_base;
> - /* Default I/O is IRQ based */
> - mcbsp[i].io_type = OMAP_MCBSP_IRQ_IO;
> - mcbsp[i].tx_irq = mcbsp_info[i].tx_irq;
> - mcbsp[i].rx_irq = mcbsp_info[i].rx_irq;
> - mcbsp[i].dma_rx_sync = mcbsp_info[i].dma_rx_sync;
> - mcbsp[i].dma_tx_sync = mcbsp_info[i].dma_tx_sync;
> - spin_lock_init(&mcbsp[i].lock);
> + mcbsp_clk_disable(mcbsp);
> + mcbsp_clk_put(mcbsp);
> +
> + for (i = 0; i < mcbsp->nr_clocks; i++)
> + mcbsp->clocks[i] = NULL;
> +
> + mcbsp->free = 0;
> + mcbsp->dev = NULL;
> }
>
> return 0;
> }
>
> -arch_initcall(omap_mcbsp_init);
> +static struct platform_driver omap_mcbsp_driver = {
> + .probe = omap_mcbsp_probe,
> + .remove = omap_mcbsp_remove,
> + .driver = {
> + .name = "omap-mcbsp",
> + },
> +};
> +
> +int __init omap_mcbsp_init(void)
> +{
> + /* Register the McBSP driver */
> + return platform_driver_register(&omap_mcbsp_driver);
> +}
> +
> +
> diff --git a/include/asm-arm/arch-omap/mcbsp.h b/include/asm-arm/arch-omap/mcbsp.h
> index b53c3b2..aa47421 100644
> --- a/include/asm-arm/arch-omap/mcbsp.h
> +++ b/include/asm-arm/arch-omap/mcbsp.h
> @@ -24,7 +24,11 @@
> #ifndef __ASM_ARCH_OMAP_MCBSP_H
> #define __ASM_ARCH_OMAP_MCBSP_H
>
> +#include <linux/completion.h>
> +#include <linux/spinlock.h>
> +
> #include <asm/hardware.h>
> +#include <asm/arch/clock.h>
>
> #define OMAP730_MCBSP1_BASE 0xfffb1000
> #define OMAP730_MCBSP2_BASE 0xfffb1800
> @@ -40,6 +44,9 @@
> #define OMAP24XX_MCBSP1_BASE 0x48074000
> #define OMAP24XX_MCBSP2_BASE 0x48076000
>
> +#define OMAP34XX_MCBSP1_BASE 0x48074000
> +#define OMAP34XX_MCBSP2_BASE 0x49022000
> +
> #if defined(CONFIG_ARCH_OMAP15XX) || defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP730)
>
> #define OMAP_MCBSP_REG_DRR2 0x00
> @@ -74,7 +81,8 @@
> #define OMAP_MCBSP_REG_XCERG 0x3A
> #define OMAP_MCBSP_REG_XCERH 0x3C
>
> -#define OMAP_MAX_MCBSP_COUNT 3
> +#define OMAP_MAX_MCBSP_COUNT 3
> +#define MAX_MCBSP_CLOCKS 3
>
> #define AUDIO_MCBSP_DATAWRITE (OMAP1510_MCBSP1_BASE + OMAP_MCBSP_REG_DXR1)
> #define AUDIO_MCBSP_DATAREAD (OMAP1510_MCBSP1_BASE + OMAP_MCBSP_REG_DRR1)
> @@ -117,7 +125,8 @@
> #define OMAP_MCBSP_REG_XCERG 0x74
> #define OMAP_MCBSP_REG_XCERH 0x78
>
> -#define OMAP_MAX_MCBSP_COUNT 2
> +#define OMAP_MAX_MCBSP_COUNT 2
> +#define MAX_MCBSP_CLOCKS 2
>
> #define AUDIO_MCBSP_DATAWRITE (OMAP24XX_MCBSP2_BASE + OMAP_MCBSP_REG_DXR1)
> #define AUDIO_MCBSP_DATAREAD (OMAP24XX_MCBSP2_BASE + OMAP_MCBSP_REG_DRR1)
> @@ -298,6 +307,66 @@ struct omap_mcbsp_spi_cfg {
> omap_mcbsp_word_length word_length;
> };
>
> +/* Platform specific configuration */
> +struct omap_mcbsp_ops {
> + void (*request)(unsigned int);
> + void (*free)(unsigned int);
> + int (*check)(unsigned int);
> +};
> +
> +struct omap_mcbsp_platform_data {
> + u32 virt_base;
> + u8 dma_rx_sync, dma_tx_sync;
> + u16 rx_irq, tx_irq;
> + struct omap_mcbsp_ops *ops;
> + char const *clocks[MAX_MCBSP_CLOCKS];
> +};
> +
> +struct omap_mcbsp {
> + struct device *dev;
> + u32 io_base;
> + u8 id;
> + u8 free;
> + omap_mcbsp_word_length rx_word_length;
> + omap_mcbsp_word_length tx_word_length;
> +
> + omap_mcbsp_io_type_t io_type; /* IRQ or poll */
> + /* IRQ based TX/RX */
> + int rx_irq;
> + int tx_irq;
> +
> + /* DMA stuff */
> + u8 dma_rx_sync;
> + short dma_rx_lch;
> + u8 dma_tx_sync;
> + short dma_tx_lch;
> +
> + /* Completion queues */
> + struct completion tx_irq_completion;
> + struct completion rx_irq_completion;
> + struct completion tx_dma_completion;
> + struct completion rx_dma_completion;
> +
> + /* Protect the field .free, while checking if the mcbsp is in use */
> + spinlock_t lock;
> + struct omap_mcbsp_platform_data *pdata;
> + int nr_clocks;
> + struct clk *clocks[MAX_MCBSP_CLOCKS];
> +};
> +
> +#define __mcbsp_clk_op(mcbsp, op) \
> + do { \
> + int i; \
> + for (i = 0; i < mcbsp->nr_clocks; i++) \
> + clk_##op(mcbsp->clocks[i]); \
> + } while (0)
> +#define mcbsp_clk_enable(mcbsp) __mcbsp_clk_op((mcbsp), enable)
> +#define mcbsp_clk_disable(mcbsp) __mcbsp_clk_op((mcbsp), disable)
> +#define mcbsp_clk_put(mcbsp) __mcbsp_clk_op((mcbsp), put)
> +
These macros make things hard to read.. It would be best to have
things set up in a way so you can just call clk_enable/disable in
mcbsp.c.
Tony
> +int omap_mcbsp_init(void);
> +void omap_mcbsp_register_board_cfg(struct omap_mcbsp_platform_data *config,
> + int size);
> void omap_mcbsp_config(unsigned int id, const struct omap_mcbsp_reg_cfg * config);
> int omap_mcbsp_request(unsigned int id);
> void omap_mcbsp_free(unsigned int id);
> --
> 1.5.5.1.67.gbdb8.dirty
>
[-- Attachment #2: 24xx-mcbsp-clocks.patch --]
[-- Type: text/x-diff, Size: 3223 bytes --]
>From d73a8241df49e45e57f96a807c11487b88f18c45 Mon Sep 17 00:00:00 2001
From: Tony Lindgren <tony@atomide.com>
Date: Tue, 20 May 2008 16:32:49 -0700
Subject: [PATCH] ARM: OMAP: Fix 24xx mcbsp clocks
Fix 24xx mcbsp clocks
Signed-off-by: Tony Lindgren <tony@atomide.com>
diff --git a/arch/arm/mach-omap2/clock24xx.h b/arch/arm/mach-omap2/clock24xx.h
index c439be8..be4e255 100644
--- a/arch/arm/mach-omap2/clock24xx.h
+++ b/arch/arm/mach-omap2/clock24xx.h
@@ -1754,7 +1754,8 @@ static struct clk gpt12_fck = {
};
static struct clk mcbsp1_ick = {
- .name = "mcbsp1_ick",
+ .name = "mcbsp_ick",
+ .id = 1,
.parent = &l4_ck,
.flags = CLOCK_IN_OMAP242X | CLOCK_IN_OMAP243X,
.enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN1),
@@ -1763,7 +1764,8 @@ static struct clk mcbsp1_ick = {
};
static struct clk mcbsp1_fck = {
- .name = "mcbsp1_fck",
+ .name = "mcbsp_fck",
+ .id = 1,
.parent = &func_96m_ck,
.flags = CLOCK_IN_OMAP242X | CLOCK_IN_OMAP243X,
.enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_FCLKEN1),
@@ -1772,7 +1774,8 @@ static struct clk mcbsp1_fck = {
};
static struct clk mcbsp2_ick = {
- .name = "mcbsp2_ick",
+ .name = "mcbsp_ick",
+ .id = 2,
.parent = &l4_ck,
.flags = CLOCK_IN_OMAP242X | CLOCK_IN_OMAP243X,
.enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN1),
@@ -1781,7 +1784,8 @@ static struct clk mcbsp2_ick = {
};
static struct clk mcbsp2_fck = {
- .name = "mcbsp2_fck",
+ .name = "mcbsp_fck",
+ .id = 2,
.parent = &func_96m_ck,
.flags = CLOCK_IN_OMAP242X | CLOCK_IN_OMAP243X,
.enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_FCLKEN1),
@@ -1790,7 +1794,8 @@ static struct clk mcbsp2_fck = {
};
static struct clk mcbsp3_ick = {
- .name = "mcbsp3_ick",
+ .name = "mcbsp_ick",
+ .id = 3,
.parent = &l4_ck,
.flags = CLOCK_IN_OMAP243X,
.enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN2),
@@ -1799,7 +1804,8 @@ static struct clk mcbsp3_ick = {
};
static struct clk mcbsp3_fck = {
- .name = "mcbsp3_fck",
+ .name = "mcbsp_fck",
+ .id = 3,
.parent = &func_96m_ck,
.flags = CLOCK_IN_OMAP243X,
.enable_reg = OMAP_CM_REGADDR(CORE_MOD, OMAP24XX_CM_FCLKEN2),
@@ -1808,7 +1814,8 @@ static struct clk mcbsp3_fck = {
};
static struct clk mcbsp4_ick = {
- .name = "mcbsp4_ick",
+ .name = "mcbsp_ick",
+ .id = 4,
.parent = &l4_ck,
.flags = CLOCK_IN_OMAP243X,
.enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN2),
@@ -1817,7 +1824,8 @@ static struct clk mcbsp4_ick = {
};
static struct clk mcbsp4_fck = {
- .name = "mcbsp4_fck",
+ .name = "mcbsp_fck",
+ .id = 4,
.parent = &func_96m_ck,
.flags = CLOCK_IN_OMAP243X,
.enable_reg = OMAP_CM_REGADDR(CORE_MOD, OMAP24XX_CM_FCLKEN2),
@@ -1826,7 +1834,8 @@ static struct clk mcbsp4_fck = {
};
static struct clk mcbsp5_ick = {
- .name = "mcbsp5_ick",
+ .name = "mcbsp_ick",
+ .id = 5,
.parent = &l4_ck,
.flags = CLOCK_IN_OMAP243X,
.enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN2),
@@ -1835,7 +1844,8 @@ static struct clk mcbsp5_ick = {
};
static struct clk mcbsp5_fck = {
- .name = "mcbsp5_fck",
+ .name = "mcbsp_fck",
+ .id = 5,
.parent = &func_96m_ck,
.flags = CLOCK_IN_OMAP243X,
.enable_reg = OMAP_CM_REGADDR(CORE_MOD, OMAP24XX_CM_FCLKEN2),
next prev parent reply other threads:[~2008-05-20 23:44 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-05-05 21:23 [PATCH 0/4] Updates on mcbsp driver (take #2) Eduardo Valentin
2008-05-05 21:23 ` [PATCH 1/4] PLAT-OMAP: MCBSP: Tranform into platform driver Eduardo Valentin
2008-05-05 21:23 ` [PATCH 2/4] MACH-OMAP1: MCBSP: Add support for mcbsp on mach-omap1 Eduardo Valentin
2008-05-05 21:23 ` [PATCH 3/4] Fix mcbsp clock definition on clock34xx.h Eduardo Valentin
2008-05-05 21:23 ` [PATCH 4/4] MACH-OMAP2: MCBSP: Add support for mcbsp on mach-omap2 Eduardo Valentin
2008-05-08 11:23 ` [PATCH 1/4] PLAT-OMAP: MCBSP: Tranform into platform driver Trilok Soni
2008-05-08 12:13 ` Eduardo Valentin
2008-05-20 23:44 ` Tony Lindgren [this message]
2008-05-29 15:30 ` Eduardo Valentin
2008-05-16 15:54 ` [PATCH 0/4] Updates on mcbsp driver (take #2) Tony Lindgren
2008-05-19 14:26 ` Steve Sakoman
2008-05-19 15:09 ` Eduardo Valentin
2008-05-20 11:21 ` Jarkko Nikula
2008-06-12 19:14 ` Steve Sakoman
2008-06-13 6:31 ` Jarkko Nikula
2008-05-20 6:47 ` Chandra shekhar
2008-05-20 18:27 ` Koen Kooi
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20080520234438.GR23002@atomide.com \
--to=tony@atomide.com \
--cc=eduardo.valentin@indt.org.br \
--cc=edubezval@gmail.com \
--cc=linux-omap@vger.kernel.org \
--cc=x0044955@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox