* [PATCH] OMAP2EVM : Add touchscreen support
@ 2008-09-24 14:14 Arun KS
2008-09-24 14:15 ` Tony Lindgren
0 siblings, 1 reply; 2+ messages in thread
From: Arun KS @ 2008-09-24 14:14 UTC (permalink / raw)
To: linux-omap@vger.kernel.org
This patch adds ads7846 touchscreen support to omap2evm board
Signed-off-by: Arun KS <arunks@mistralsolutions.com>
---
arch/arm/mach-omap2/board-omap2evm.c | 64 ++++++++++++++++++++++
arch/arm/mach-omap2/mux.c | 11 ++++
arch/arm/plat-omap/include/mach/board-omap2evm.h | 2 +
arch/arm/plat-omap/include/mach/mux.h | 9 +++
4 files changed, 86 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-omap2evm.c
b/arch/arm/mach-omap2/board-omap2evm.c
index 6ce7740..2cf13b1 100644
--- a/arch/arm/mach-omap2/board-omap2evm.c
+++ b/arch/arm/mach-omap2/board-omap2evm.c
@@ -22,6 +22,8 @@
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/nand.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/ads7846.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
@@ -36,6 +38,8 @@
#include <mach/keypad.h>
#include <mach/gpmc.h>
#include <mach/nand.h>
+#include <mach/mcspi.h>
+#include <mach/mux.h>
#define GPMC_OFF_CONFIG1_0 0x60
@@ -181,6 +185,62 @@ static struct omap_lcd_config
omap2_evm_lcd_config __initdata = {
.ctrl_name = "internal",
};
+static void ads7846_dev_init(void)
+{
+
+ /*Setting the MUX */
+ omap_cfg_reg(Y18_2430_MCSPI1_CLK);
+ omap_cfg_reg(AD15_2430_MCSPI1_SIMO);
+ omap_cfg_reg(AE17_2430_MCSPI1_SOMI);
+ omap_cfg_reg(U1_2430_MCSPI1_CS0);
+
+ omap_cfg_reg(AF19_2430_GPIO_85);
+
+ if (omap_request_gpio(OMAP2_EVM_TS_GPIO) < 0)
+ printk(KERN_ERR "can't get ads7846 pen down GPIO\n");
+
+ omap_set_gpio_direction(OMAP2_EVM_TS_GPIO, 1);
+
+ omap_set_gpio_debounce(OMAP2_EVM_TS_GPIO, 1);
+ omap_set_gpio_debounce_time(OMAP2_EVM_TS_GPIO, 0xa);
+}
+
+static int ads7846_get_pendown_state(void)
+{
+ return !omap_get_gpio_datain(OMAP2_EVM_TS_GPIO);
+}
+
+struct ads7846_platform_data ads7846_config = {
+ .x_max = 0x0fff,
+ .y_max = 0x0fff,
+ .x_plate_ohms = 180,
+ .pressure_max = 255,
+ .debounce_max = 10,
+ .debounce_tol = 3,
+ .debounce_rep = 1,
+ .get_pendown_state = ads7846_get_pendown_state,
+ .keep_vref_on = 1,
+ .settle_delay_usecs = 150,
+};
+
+static struct omap2_mcspi_device_config ads7846_mcspi_config = {
+ .turbo_mode = 0,
+ .single_channel = 1, /* 0: slave, 1: master */
+};
+
+struct spi_board_info omap2evm_spi_board_info[] = {
+ [0] = {
+ .modalias = "ads7846",
+ .bus_num = 1,
+ .chip_select = 0,
+ .max_speed_hz = 1500000,
+ .controller_data = &ads7846_mcspi_config,
+ .irq = OMAP_GPIO_IRQ(OMAP2_EVM_TS_GPIO),
+ .platform_data = &ads7846_config,
+ },
+};
+
+
static int omap2evm_keymap[] = {
KEY(0, 0, KEY_LEFT),
KEY(0, 1, KEY_RIGHT),
@@ -269,9 +329,13 @@ static void __init omap2_evm_init(void)
platform_add_devices(omap2_evm_devices, ARRAY_SIZE(omap2_evm_devices));
omap_board_config = omap2_evm_config;
omap_board_config_size = ARRAY_SIZE(omap2_evm_config);
+
+ spi_register_board_info(omap2evm_spi_board_info,
+ ARRAY_SIZE(omap2evm_spi_board_info));
omap_serial_init();
hsmmc_init();
omap2evm_flash_init();
+ ads7846_dev_init();
}
static void __init omap2_evm_map_io(void)
diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c
index 741ab18..7bbd87e 100644
--- a/arch/arm/mach-omap2/mux.c
+++ b/arch/arm/mach-omap2/mux.c
@@ -210,6 +210,17 @@ MUX_CFG_24XX("AC10_2430_MCBSP2_FSX_OFF",0x012E, 0, 0, 0, 1)
MUX_CFG_24XX("AD16_2430_MCBSP2_CLX_OFF",0x012F, 0, 0, 0, 1)
MUX_CFG_24XX("AE13_2430_MCBSP2_DX_OFF", 0x0130, 0, 0, 0, 1)
MUX_CFG_24XX("AD13_2430_MCBSP2_DR_OFF", 0x0131, 0, 0, 0, 1)
+
+/* 2430 MCSPI1 */
+MUX_CFG_24XX("SPI1_2430_MCSPI1_CLK", 0x010F, 0, 0, 0, 1)
+MUX_CFG_24XX("SPI1_2430_MCSPI1_SIMO", 0x0110, 0, 0, 0, 1)
+MUX_CFG_24XX("SPI1_2430_MCSPI1_SOMI", 0x0111, 0, 0, 0, 1)
+MUX_CFG_24XX("SPI1_2430_MCSPI1_CS0", 0x0112, 0, 0, 0, 1)
+MUX_CFG_24XX("SPI1_2430_GPIO_85", 0x0113, 3, 0, 0, 1)
+
+/* Touchscreen GPIO */
+MUX_CFG_24XX("AF19_2430_GPIO_85", 0x0113, 3, 0, 0, 1)
+
};
#define OMAP24XX_PINS_SZ ARRAY_SIZE(omap24xx_pins)
diff --git a/arch/arm/plat-omap/include/mach/board-omap2evm.h
b/arch/arm/plat-omap/include/mach/board-omap2evm.h
index ec548d4..b46fba6 100644
--- a/arch/arm/plat-omap/include/mach/board-omap2evm.h
+++ b/arch/arm/plat-omap/include/mach/board-omap2evm.h
@@ -34,4 +34,6 @@
#define OMAP2EVM_ETHR_SIZE 1024
#define OMAP2EVM_ETHR_GPIO_IRQ 149
+#define OMAP2_EVM_TS_GPIO 85
+
#endif /* __ASM_ARCH_OMAP2_EVM_H */
diff --git a/arch/arm/plat-omap/include/mach/mux.h
b/arch/arm/plat-omap/include/mach/mux.h
index 5670d56..683474f 100644
--- a/arch/arm/plat-omap/include/mach/mux.h
+++ b/arch/arm/plat-omap/include/mach/mux.h
@@ -641,6 +641,15 @@ enum omap24xx_index {
AE13_2430_MCBSP2_DX_OFF,
AD13_2430_MCBSP2_DR_OFF,
+ /* 2430 McSPI*/
+ Y18_2430_MCSPI1_CLK,
+ AD15_2430_MCSPI1_SIMO,
+ AE17_2430_MCSPI1_SOMI,
+ U1_2430_MCSPI1_CS0,
+
+ /* Touchscreen GPIO */
+ AF19_2430_GPIO_85,
+
};
enum omap34xx_index {
--
1.5.3.4
^ permalink raw reply related [flat|nested] 2+ messages in thread
* Re: [PATCH] OMAP2EVM : Add touchscreen support
2008-09-24 14:14 [PATCH] OMAP2EVM : Add touchscreen support Arun KS
@ 2008-09-24 14:15 ` Tony Lindgren
0 siblings, 0 replies; 2+ messages in thread
From: Tony Lindgren @ 2008-09-24 14:15 UTC (permalink / raw)
To: Arun KS; +Cc: linux-omap@vger.kernel.org
* Arun KS <arunks@mistralsolutions.com> [080924 17:14]:
> This patch adds ads7846 touchscreen support to omap2evm board
Can you please split the mux changes into a separate patch?
Thanks,
Tony
> Signed-off-by: Arun KS <arunks@mistralsolutions.com>
> ---
> arch/arm/mach-omap2/board-omap2evm.c | 64 ++++++++++++++++++++++
> arch/arm/mach-omap2/mux.c | 11 ++++
> arch/arm/plat-omap/include/mach/board-omap2evm.h | 2 +
> arch/arm/plat-omap/include/mach/mux.h | 9 +++
> 4 files changed, 86 insertions(+), 0 deletions(-)
>
> diff --git a/arch/arm/mach-omap2/board-omap2evm.c
> b/arch/arm/mach-omap2/board-omap2evm.c
> index 6ce7740..2cf13b1 100644
> --- a/arch/arm/mach-omap2/board-omap2evm.c
> +++ b/arch/arm/mach-omap2/board-omap2evm.c
> @@ -22,6 +22,8 @@
> #include <linux/mtd/mtd.h>
> #include <linux/mtd/partitions.h>
> #include <linux/mtd/nand.h>
> +#include <linux/spi/spi.h>
> +#include <linux/spi/ads7846.h>
>
> #include <mach/hardware.h>
> #include <asm/mach-types.h>
> @@ -36,6 +38,8 @@
> #include <mach/keypad.h>
> #include <mach/gpmc.h>
> #include <mach/nand.h>
> +#include <mach/mcspi.h>
> +#include <mach/mux.h>
>
> #define GPMC_OFF_CONFIG1_0 0x60
>
> @@ -181,6 +185,62 @@ static struct omap_lcd_config
> omap2_evm_lcd_config __initdata = {
> .ctrl_name = "internal",
> };
>
> +static void ads7846_dev_init(void)
> +{
> +
> + /*Setting the MUX */
> + omap_cfg_reg(Y18_2430_MCSPI1_CLK);
> + omap_cfg_reg(AD15_2430_MCSPI1_SIMO);
> + omap_cfg_reg(AE17_2430_MCSPI1_SOMI);
> + omap_cfg_reg(U1_2430_MCSPI1_CS0);
> +
> + omap_cfg_reg(AF19_2430_GPIO_85);
> +
> + if (omap_request_gpio(OMAP2_EVM_TS_GPIO) < 0)
> + printk(KERN_ERR "can't get ads7846 pen down GPIO\n");
> +
> + omap_set_gpio_direction(OMAP2_EVM_TS_GPIO, 1);
> +
> + omap_set_gpio_debounce(OMAP2_EVM_TS_GPIO, 1);
> + omap_set_gpio_debounce_time(OMAP2_EVM_TS_GPIO, 0xa);
> +}
> +
> +static int ads7846_get_pendown_state(void)
> +{
> + return !omap_get_gpio_datain(OMAP2_EVM_TS_GPIO);
> +}
> +
> +struct ads7846_platform_data ads7846_config = {
> + .x_max = 0x0fff,
> + .y_max = 0x0fff,
> + .x_plate_ohms = 180,
> + .pressure_max = 255,
> + .debounce_max = 10,
> + .debounce_tol = 3,
> + .debounce_rep = 1,
> + .get_pendown_state = ads7846_get_pendown_state,
> + .keep_vref_on = 1,
> + .settle_delay_usecs = 150,
> +};
> +
> +static struct omap2_mcspi_device_config ads7846_mcspi_config = {
> + .turbo_mode = 0,
> + .single_channel = 1, /* 0: slave, 1: master */
> +};
> +
> +struct spi_board_info omap2evm_spi_board_info[] = {
> + [0] = {
> + .modalias = "ads7846",
> + .bus_num = 1,
> + .chip_select = 0,
> + .max_speed_hz = 1500000,
> + .controller_data = &ads7846_mcspi_config,
> + .irq = OMAP_GPIO_IRQ(OMAP2_EVM_TS_GPIO),
> + .platform_data = &ads7846_config,
> + },
> +};
> +
> +
> static int omap2evm_keymap[] = {
> KEY(0, 0, KEY_LEFT),
> KEY(0, 1, KEY_RIGHT),
> @@ -269,9 +329,13 @@ static void __init omap2_evm_init(void)
> platform_add_devices(omap2_evm_devices, ARRAY_SIZE(omap2_evm_devices));
> omap_board_config = omap2_evm_config;
> omap_board_config_size = ARRAY_SIZE(omap2_evm_config);
> +
> + spi_register_board_info(omap2evm_spi_board_info,
> + ARRAY_SIZE(omap2evm_spi_board_info));
> omap_serial_init();
> hsmmc_init();
> omap2evm_flash_init();
> + ads7846_dev_init();
> }
>
> static void __init omap2_evm_map_io(void)
> diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c
> index 741ab18..7bbd87e 100644
> --- a/arch/arm/mach-omap2/mux.c
> +++ b/arch/arm/mach-omap2/mux.c
> @@ -210,6 +210,17 @@ MUX_CFG_24XX("AC10_2430_MCBSP2_FSX_OFF",0x012E, 0, 0, 0, 1)
> MUX_CFG_24XX("AD16_2430_MCBSP2_CLX_OFF",0x012F, 0, 0, 0, 1)
> MUX_CFG_24XX("AE13_2430_MCBSP2_DX_OFF", 0x0130, 0, 0, 0, 1)
> MUX_CFG_24XX("AD13_2430_MCBSP2_DR_OFF", 0x0131, 0, 0, 0, 1)
> +
> +/* 2430 MCSPI1 */
> +MUX_CFG_24XX("SPI1_2430_MCSPI1_CLK", 0x010F, 0, 0, 0, 1)
> +MUX_CFG_24XX("SPI1_2430_MCSPI1_SIMO", 0x0110, 0, 0, 0, 1)
> +MUX_CFG_24XX("SPI1_2430_MCSPI1_SOMI", 0x0111, 0, 0, 0, 1)
> +MUX_CFG_24XX("SPI1_2430_MCSPI1_CS0", 0x0112, 0, 0, 0, 1)
> +MUX_CFG_24XX("SPI1_2430_GPIO_85", 0x0113, 3, 0, 0, 1)
> +
> +/* Touchscreen GPIO */
> +MUX_CFG_24XX("AF19_2430_GPIO_85", 0x0113, 3, 0, 0, 1)
> +
> };
>
> #define OMAP24XX_PINS_SZ ARRAY_SIZE(omap24xx_pins)
> diff --git a/arch/arm/plat-omap/include/mach/board-omap2evm.h
> b/arch/arm/plat-omap/include/mach/board-omap2evm.h
> index ec548d4..b46fba6 100644
> --- a/arch/arm/plat-omap/include/mach/board-omap2evm.h
> +++ b/arch/arm/plat-omap/include/mach/board-omap2evm.h
> @@ -34,4 +34,6 @@
> #define OMAP2EVM_ETHR_SIZE 1024
> #define OMAP2EVM_ETHR_GPIO_IRQ 149
>
> +#define OMAP2_EVM_TS_GPIO 85
> +
> #endif /* __ASM_ARCH_OMAP2_EVM_H */
> diff --git a/arch/arm/plat-omap/include/mach/mux.h
> b/arch/arm/plat-omap/include/mach/mux.h
> index 5670d56..683474f 100644
> --- a/arch/arm/plat-omap/include/mach/mux.h
> +++ b/arch/arm/plat-omap/include/mach/mux.h
> @@ -641,6 +641,15 @@ enum omap24xx_index {
> AE13_2430_MCBSP2_DX_OFF,
> AD13_2430_MCBSP2_DR_OFF,
>
> + /* 2430 McSPI*/
> + Y18_2430_MCSPI1_CLK,
> + AD15_2430_MCSPI1_SIMO,
> + AE17_2430_MCSPI1_SOMI,
> + U1_2430_MCSPI1_CS0,
> +
> + /* Touchscreen GPIO */
> + AF19_2430_GPIO_85,
> +
> };
>
> enum omap34xx_index {
> --
> 1.5.3.4
> --
> To unsubscribe from this list: send the line "unsubscribe linux-omap" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2008-09-24 14:15 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-09-24 14:14 [PATCH] OMAP2EVM : Add touchscreen support Arun KS
2008-09-24 14:15 ` Tony Lindgren
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox