public inbox for linux-omap@vger.kernel.org
 help / color / mirror / Atom feed
* [patch 2.6.28-rc2-omap] H4 stops using gpio_expander_omap
@ 2008-10-29 21:43 David Brownell
  2008-11-13 21:10 ` Tony Lindgren
  0 siblings, 1 reply; 3+ messages in thread
From: David Brownell @ 2008-10-29 21:43 UTC (permalink / raw)
  To: linux-omap

From: David Brownell <dbrownell@users.sourceforge.net>

This patch starts updating the H4 board support to use gpiolib.  It
switches from the gpio_expander_omap.c code to the mainline pcf8474
driver for its three I2C GPIO expanders.

It also adds two minor features:  LCD stays powered off when it's not
used; and the backlight control is exposed through the LED framework
(using the new "backlight" trigger).

Plus it fixes a bug that would have affected anyone trying to use the
camera sensor:  it wouldn't power up, since 0x80 != 0x08.  (Though
there's no mainline V4L2 driver for that sensor yet...)

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
---
Once H3 has a similar patch, one drivers/i2c/chips driver can go...

 arch/arm/mach-omap2/Kconfig                |    1 
 arch/arm/mach-omap2/board-h4.c             |  189 +++++++++++++++++----------
 arch/arm/plat-omap/include/mach/board-h4.h |   42 ++++++
 drivers/i2c/chips/Kconfig                  |    2 
 drivers/net/irda/Kconfig                   |    2 
 5 files changed, 165 insertions(+), 71 deletions(-)

--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -59,7 +59,6 @@ config MACH_OMAP_H4
 	bool "OMAP 2420 H4 board"
 	depends on ARCH_OMAP2 && ARCH_OMAP2420
 	select OMAP_DEBUG_DEVICES
-	select GPIOEXPANDER_OMAP
 
 config MACH_OMAP_H4_TUSB
 	bool "TUSB 6010 EVM board"
--- a/arch/arm/mach-omap2/board-h4.c
+++ b/arch/arm/mach-omap2/board-h4.c
@@ -22,8 +22,13 @@
 #include <linux/err.h>
 #include <linux/clk.h>
 #include <linux/i2c.h>
+#include <linux/gpio.h>
+#include <linux/leds.h>
+
 #include <linux/i2c/at24.h>
 #include <linux/i2c/menelaus.h>
+#include <linux/i2c/pcf857x.h>
+
 #include <linux/spi/spi.h>
 #include <linux/spi/tsc210x.h>
 
@@ -36,8 +41,6 @@
 #include <asm/mach/flash.h>
 
 #include <mach/control.h>
-#include <mach/gpio.h>
-#include <mach/gpioexpander.h>
 #include <mach/mux.h>
 #include <mach/usb.h>
 #include <mach/irda.h>
@@ -142,32 +145,16 @@ static struct platform_device h4_flash_d
 	.resource	= &h4_flash_resource,
 };
 
-/* Select between the IrDA and aGPS module
- */
 #if defined(CONFIG_OMAP_IR) || defined(CONFIG_OMAP_IR_MODULE)
+
+/* Select between the IrDA and aGPS module */
 static int h4_select_irda(struct device *dev, int state)
 {
-	unsigned char expa;
-	int err = 0;
-
-	if ((err = read_gpio_expa(&expa, 0x21))) {
-		printk(KERN_ERR "Error reading from I/O expander\n");
-		return err;
-	}
+	/* U192.P0 = high for IRDA; else AGPS */
+	gpio_set_value_cansleep(H4_GPIO_IRDA_AGPSn, state & IR_SEL);
 
-	/* 'P6' enable/disable IRDA_TX and IRDA_RX */
-	if (state & IR_SEL) {	/* IrDa */
-		if ((err = write_gpio_expa(expa | 0x01, 0x21))) {
-			printk(KERN_ERR "Error writing to I/O expander\n");
-			return err;
-		}
-	} else {
-		if ((err = write_gpio_expa(expa & ~0x01, 0x21))) {
-			printk(KERN_ERR "Error writing to I/O expander\n");
-			return err;
-		}
-	}
-	return err;
+	/* NOTE:  UART3 can also hook up to a DB9 or to GSM ... */
+	return 0;
 }
 
 static void set_trans_mode(struct work_struct *work)
@@ -175,22 +162,9 @@ static void set_trans_mode(struct work_s
 	struct omap_irda_config *irda_config =
 		container_of(work, struct omap_irda_config, gpio_expa.work);
 	int mode = irda_config->mode;
-	unsigned char expa;
-	int err = 0;
-
-	if ((err = read_gpio_expa(&expa, 0x20)) != 0) {
-		printk(KERN_ERR "Error reading from I/O expander\n");
-	}
-
-	expa &= ~0x01;
-
-	if (!(mode & IR_SIRMODE)) { /* MIR/FIR */
-		expa |= 0x01;
-	}
 
-	if ((err = write_gpio_expa(expa, 0x20)) != 0) {
-		printk(KERN_ERR "Error writing to I/O expander\n");
-	}
+	/* U191.P0 = low for SIR; else MIR/FIR */
+	gpio_set_value_cansleep(H4_GPIO_IRDA_FIRSEL, !(mode & IR_SIRMODE));
 }
 
 static int h4_transceiver_mode(struct device *dev, int mode)
@@ -568,37 +542,13 @@ const static struct ov9640_reg ov9640_co
 
 static int ov9640_sensor_power_set(int power)
 {
-	unsigned char expa;
-	int err;
-
-	/* read current state of GPIO EXPA outputs */
-	if ((err = read_gpio_expa(&expa, 0x20))) {
-		printk(KERN_ERR "Error reading GPIO EXPA 0x20\n");
-		return err;
-	}
-
-	expa = power ? expa | 0x80 : expa & ~0x08;
-
-	/* Set GPIO EXPA P3 (CAMERA_MODULE_EN) to power-up sensor */
-	if ((err = write_gpio_expa(expa, 0x20))) {
-		printk(KERN_ERR "Error writing to GPIO EXPA 0x20\n");
-		return err;
-	}
+	/* power up the sensor? */
+	gpio_set_value_cansleep(H4_GPIO_CAM_MODULE_EN, power);
 
-	if (power) {
-		/* read current state of GPIO EXPA outputs */
-		if ((err = read_gpio_expa(&expa, 0x22))) {
-			printk(KERN_ERR "Error reading GPIO EXPA\n");
-			return err;
-		}
-		/* Clear GPIO EXPA P7 (CAM_RST) */
-		if ((err = write_gpio_expa(expa & ~0x80, 0x22))) {
-			printk(KERN_ERR "Error writing to GPIO EXPA\n");
-			return err;
-		}
-	}
+	/* take it out of reset if it's not powered */
+	gpio_direction_output(H4_GPIO_CAM_RST, !power);
 
-	return err;
+	return 0;
 }
 
 static struct v4l2_ifparm ifparm = {
@@ -626,14 +576,117 @@ static struct ov9640_platform_data h4_ov
 	.default_regs	= ov9640_common,
 	.ifparm		= ov9640_ifparm,
 };
+
 #endif
 
+/* leave LCD powered off unless it will be used */
+#if defined(CONFIG_FB_OMAP) || defined(CONFIG_FB_OMAP_MODULE)
+#define LCD_ENABLED		true
+#else
+#define LCD_ENABLED		false
+#endif
+
+static struct gpio_led backlight_leds[] = {
+	{
+		.name			= "lcd_h4",
+		.default_trigger	= "backlight",
+		.gpio			= H4_GPIO_LCD_ENBKL,
+	},
+	{ },
+};
+
+static struct gpio_led_platform_data backlight_led_data = {
+	.num_leds		= 1,
+	.leds			= backlight_leds,
+};
+
+static struct platform_device h4_backlight_device = {
+	.name			= "leds-gpio",
+	.id			= 0,
+	.dev.platform_data	= &backlight_led_data,
+};
+
+static int
+u191_setup(struct i2c_client *client, int gpio, unsigned ngpio, void *context)
+{
+	/* P0 = IRDA control, FIR/MIR vs SIR */
+	gpio_request(H4_GPIO_IRDA_FIRSEL, "irda_firsel");
+	gpio_direction_output(H4_GPIO_IRDA_FIRSEL, false);
+
+	/* P3 = camera sensor module PWDN */
+	gpio_request(H4_GPIO_CAM_MODULE_EN, "camera_en");
+	gpio_direction_output(H4_GPIO_CAM_MODULE_EN, false);
+
+	/* P7 = LCD_ENVDD ... controls power to LCD (including backlight)
+	 * P5 = LCD_ENBKL ... switches backlight
+	 */
+	gpio_request(H4_GPIO_LCD_ENVDD, "lcd_power");
+	gpio_direction_output(H4_GPIO_LCD_ENVDD, LCD_ENABLED);
+	if (LCD_ENABLED) {
+		h4_backlight_device.dev.parent = &client->dev;
+		platform_device_register(&h4_backlight_device);
+	}
+
+	/* P6 = AUDIO_ENVDD ... switch power to microphone */
+	gpio_request(H4_GPIO_AUDIO_ENVDD, "audio_power");
+	gpio_direction_output(H4_GPIO_AUDIO_ENVDD, true);
+
+	return 0;
+}
+
+
+static struct pcf857x_platform_data u191_platform_data = {
+	.gpio_base	= H4_U191_GPIO_BASE,
+	.setup		= u191_setup,
+};
+
+static int
+u192_setup(struct i2c_client *client, int gpio, unsigned ngpio, void *context)
+{
+	gpio_request(H4_GPIO_IRDA_AGPSn, "irda/agps");
+	gpio_direction_output(H4_GPIO_IRDA_AGPSn, false);
+
+	return 0;
+}
+
+static struct pcf857x_platform_data u192_platform_data = {
+	.gpio_base	= H4_U192_GPIO_BASE,
+	.setup		= u192_setup,
+};
+
+static int
+u193_setup(struct i2c_client *client, int gpio, unsigned ngpio, void *context)
+{
+	/* reset sensor */
+	gpio_request(H4_GPIO_CAM_RST, "camera_rst");
+	gpio_direction_output(H4_GPIO_CAM_RST, true);
+
+	return 0;
+}
+
+static struct pcf857x_platform_data u193_platform_data = {
+	.gpio_base	= H4_U193_GPIO_BASE,
+	.setup		= u193_setup,
+};
+
 static struct at24_platform_data m24c01 = {
 	.byte_len	= SZ_1K / 8,
 	.page_size	= 16,
 };
 
 static struct i2c_board_info __initdata h4_i2c_board_info[] = {
+	{	/* U191 gpios */
+		I2C_BOARD_INFO("pcf8574", 0x20),
+		.platform_data	= &u191_platform_data,
+	},
+	{	/* U192 gpios */
+		I2C_BOARD_INFO("pcf8574", 0x21),
+		.platform_data	= &u192_platform_data,
+	},
+	{	/* U193 gpios */
+		I2C_BOARD_INFO("pcf8574", 0x22),
+		.platform_data	= &u193_platform_data,
+	},
 	{
 		I2C_BOARD_INFO("rv5c387a", 0x32),
 		/* no IRQ wired to OMAP; nINTB goes to AGPS */
--- a/arch/arm/plat-omap/include/mach/board-h4.h
+++ b/arch/arm/plat-omap/include/mach/board-h4.h
@@ -34,5 +34,47 @@ extern void h4_mmc_init(void);
 
 /* Placeholder for H4 specific defines */
 #define OMAP24XX_ETHR_GPIO_IRQ		92
+
+/* FPGA on debug board has 32 GPIOs:  16 dedicated to leds,
+ * 8 outputs on a header, and 6 inputs from a DIP switch.
+ */
+#define H4_DEBUG_GPIO_BASE		OMAP_MAX_GPIO_LINES
+#	define H4_DEBUG_GPIO_SW3_1	(H4_DEBUG_GPIO_BASE + 24)
+#	define H4_DEBUG_GPIO_SW3_2	(H4_DEBUG_GPIO_BASE + 25)
+#	define H4_DEBUG_GPIO_SW3_3	(H4_DEBUG_GPIO_BASE + 26)
+#	define H4_DEBUG_GPIO_SW3_4	(H4_DEBUG_GPIO_BASE + 27)
+#	define H4_DEBUG_GPIO_SW3_5	(H4_DEBUG_GPIO_BASE + 28)
+#	define H4_DEBUG_GPIO_SW3_8	(H4_DEBUG_GPIO_BASE + 29)
+
+/* H4 baseboard has 3 PCF8574 (8 bit) I2C GPIO expanders */
+#define H4_U191_GPIO_BASE		(H4_DEBUG_GPIO_BASE + 32)
+#	define H4_GPIO_IRDA_FIRSEL	(H4_U191_GPIO_BASE + 0)
+#	define H4_GPIO_MODEM_MOD_EN	(H4_U191_GPIO_BASE + 1)
+#	define H4_GPIO_WLAN_MOD_EN	(H4_U191_GPIO_BASE + 2)
+#	define H4_GPIO_CAM_MODULE_EN	(H4_U191_GPIO_BASE + 3)
+#	define H4_GPIO_HANDSET_EN	(H4_U191_GPIO_BASE + 4)
+#	define H4_GPIO_LCD_ENBKL	(H4_U191_GPIO_BASE + 5)
+#	define H4_GPIO_AUDIO_ENVDD	(H4_U191_GPIO_BASE + 6)
+#	define H4_GPIO_LCD_ENVDD	(H4_U191_GPIO_BASE + 7)
+
+#define H4_U192_GPIO_BASE		(H4_U191_GPIO_BASE + 8)
+#	define H4_GPIO_IRDA_AGPSn	(H4_U192_GPIO_BASE + 0)
+#	define H4_GPIO_AGPS_PWREN	(H4_U192_GPIO_BASE + 1)
+#	define H4_GPIO_AGPS_RSTn	(H4_U192_GPIO_BASE + 2)
+#	define H4_GPIO_AGPS_SLEEP	(H4_U192_GPIO_BASE + 3)
+#	define H4_GPIO_AGPS_PA_XMT	(H4_U192_GPIO_BASE + 4)
+#	define H4_GPIO_MODEM_SPR2	(H4_U192_GPIO_BASE + 5)
+#	define H4_GPIO_MODEM_SPR1	(H4_U192_GPIO_BASE + 6)
+#	define H4_GPIO_BT_ACLK_ENn	(H4_U192_GPIO_BASE + 7)
+
+#define H4_U193_GPIO_BASE		(H4_U192_GPIO_BASE + 8)
+#	define H4_GPIO_SPR0		(H4_U193_GPIO_BASE + 0)
+#	define H4_GPIO_SPR1		(H4_U193_GPIO_BASE + 1)
+#	define H4_GPIO_WLAN_SHUTDOWN	(H4_U193_GPIO_BASE + 2)
+#	define H4_GPIO_WLAN_RESET	(H4_U193_GPIO_BASE + 3)
+#	define H4_GPIO_WLAN_CLK_ENn	(H4_U193_GPIO_BASE + 4)
+	/* 5, 6 not connected */
+#	define H4_GPIO_CAM_RST		(H4_U193_GPIO_BASE + 7)
+
 #endif /*  __ASM_ARCH_OMAP_H4_H */
 
--- a/drivers/i2c/chips/Kconfig
+++ b/drivers/i2c/chips/Kconfig
@@ -148,7 +148,7 @@ config SENSORS_TLV320AIC23
 
 config GPIOEXPANDER_OMAP
 	bool "GPIO Expander PCF8574PWR for OMAP"
-	depends on I2C && (ARCH_OMAP16XX || ARCH_OMAP24XX)
+	depends on I2C && MACH_OMAP_H3
 	help
 	  If you say yes here you get support for I/O expander calls
 	  to configure IrDA, Camera and audio devices.
--- a/drivers/net/irda/Kconfig
+++ b/drivers/net/irda/Kconfig
@@ -345,7 +345,7 @@ config MCS_FIR
 config OMAP_IR
 	tristate "OMAP IrDA(SIR/MIR/FIR)"
 	depends on IRDA && ARCH_OMAP
-	select GPIOEXPANDER_OMAP if (MACH_OMAP_H3 || MACH_OMAP_H4)
+	select GPIOEXPANDER_OMAP if MACH_OMAP_H3
         help
 	  Say Y here if you want to build support for the Texas Instruments
 	  OMAP IrDA device driver, which supports SIR/MIR/FIR. This driver

^ permalink raw reply	[flat|nested] 3+ messages in thread
end of thread, other threads:[~2008-11-14  0:22 UTC | newest]

Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-10-29 21:43 [patch 2.6.28-rc2-omap] H4 stops using gpio_expander_omap David Brownell
2008-11-13 21:10 ` Tony Lindgren
2008-11-14  0:22   ` David Brownell

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox