From: Tony Lindgren <tony@atomide.com>
To: linux-arm-kernel@lists.arm.linux.org.uk
Cc: linux-omap@vger.kernel.org
Subject: [PATCH 08/10] ARM: OMAP2/3: Add generic onenand support when connected to GPMC
Date: Tue, 19 May 2009 16:41:23 -0700 [thread overview]
Message-ID: <20090519234123.12760.11671.stgit@localhost> (raw)
In-Reply-To: <20090519232905.12760.15490.stgit@localhost>
From: Juha Yrjola <juha.yrjola@solidboot.com>
Add generic onenand support when connected to GPMC and make the
boards to use it.
The patch has been modified to make it more generic to support all
the boards with GPMC. The patch also remove unused prototype for
omap2_onenand_rephase(void).
Note that board-apollon.c is currently using the MTD_ONENAND_GENERIC
and setting the GPMC timings in the bootloader. Setting the GPMC
timings in the bootloader will not allow supporting frequency
scaling for the onenand source clock.
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/configs/rx51_defconfig | 2
arch/arm/mach-omap2/Makefile | 3
arch/arm/mach-omap2/board-rx51-peripherals.c | 52 ++++
arch/arm/mach-omap2/gpmc-onenand.c | 340 ++++++++++++++++++++++++++
arch/arm/plat-omap/include/mach/onenand.h | 29 ++
5 files changed, 423 insertions(+), 3 deletions(-)
create mode 100644 arch/arm/mach-omap2/gpmc-onenand.c
diff --git a/arch/arm/configs/rx51_defconfig b/arch/arm/configs/rx51_defconfig
index 593102d..eb2cb31 100644
--- a/arch/arm/configs/rx51_defconfig
+++ b/arch/arm/configs/rx51_defconfig
@@ -282,7 +282,7 @@ CONFIG_ALIGNMENT_TRAP=y
#
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="init=/sbin/preinit ubi.mtd=4 root=ubi0:rootfs rootfstype=ubifs rw console=ttyMTD5"
+CONFIG_CMDLINE="init=/sbin/preinit ubi.mtd=rootfs root=ubi0:rootfs rootfstype=ubifs rootflags=bulk_read,no_chk_data_crc rw console=ttyMTD,log console=tty0"
# CONFIG_XIP_KERNEL is not set
# CONFIG_KEXEC is not set
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index bf3827a..11f7f66 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -58,3 +58,6 @@ obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51.o \
ifeq ($(CONFIG_USB_MUSB_SOC),y)
obj-y += usb-musb.o
endif
+
+onenand-$(CONFIG_MTD_ONENAND_OMAP2) := gpmc-onenand.o
+obj-y += $(onenand-m) $(onenand-y)
diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c
index a738172..62a401a 100644
--- a/arch/arm/mach-omap2/board-rx51-peripherals.c
+++ b/arch/arm/mach-omap2/board-rx51-peripherals.c
@@ -27,6 +27,7 @@
#include <mach/dma.h>
#include <mach/gpmc.h>
#include <mach/keypad.h>
+#include <mach/onenand.h>
#include "mmc-twl4030.h"
@@ -408,6 +409,56 @@ static int __init rx51_i2c_init(void)
return 0;
}
+#if defined(CONFIG_MTD_ONENAND_OMAP2) || \
+ defined(CONFIG_MTD_ONENAND_OMAP2_MODULE)
+
+static struct mtd_partition onenand_partitions[] = {
+ {
+ .name = "bootloader",
+ .offset = 0,
+ .size = 0x20000,
+ .mask_flags = MTD_WRITEABLE, /* Force read-only */
+ },
+ {
+ .name = "config",
+ .offset = MTDPART_OFS_APPEND,
+ .size = 0x60000,
+ },
+ {
+ .name = "log",
+ .offset = MTDPART_OFS_APPEND,
+ .size = 0x40000,
+ },
+ {
+ .name = "kernel",
+ .offset = MTDPART_OFS_APPEND,
+ .size = 0x200000,
+ },
+ {
+ .name = "initfs",
+ .offset = MTDPART_OFS_APPEND,
+ .size = 0x200000,
+ },
+ {
+ .name = "rootfs",
+ .offset = MTDPART_OFS_APPEND,
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static struct omap_onenand_platform_data board_onenand_data = {
+ .cs = 0,
+ .gpio_irq = 65,
+ .parts = onenand_partitions,
+ .nr_parts = ARRAY_SIZE(onenand_partitions),
+};
+
+static void __init board_onenand_init(void)
+{
+ gpmc_onenand_init(&board_onenand_data);
+}
+
+#endif
void __init rx51_peripherals_init(void)
{
@@ -415,5 +466,6 @@ void __init rx51_peripherals_init(void)
ARRAY_SIZE(rx51_peripherals_devices));
rx51_i2c_init();
rx51_init_smc91x();
+ board_onenand_init();
}
diff --git a/arch/arm/mach-omap2/gpmc-onenand.c b/arch/arm/mach-omap2/gpmc-onenand.c
new file mode 100644
index 0000000..712af59
--- /dev/null
+++ b/arch/arm/mach-omap2/gpmc-onenand.c
@@ -0,0 +1,340 @@
+/*
+ * linux/arch/arm/mach-omap2/gpmc-onenand.c
+ *
+ * Copyright (C) 2006 - 2009 Nokia Corporation
+ * Contacts: Juha Yrjola
+ * Tony Lindgren
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <asm/mach/flash.h>
+#include <linux/mtd/onenand_regs.h>
+
+#include <linux/io.h>
+#include <mach/onenand.h>
+#include <mach/board.h>
+#include <mach/gpmc.h>
+
+static struct omap_onenand_platform_data *gpmc_onenand_data;
+
+static struct platform_device gpmc_onenand_device = {
+ .name = "omap2-onenand",
+ .id = -1,
+};
+
+static int omap2_onenand_set_async_mode(int cs, void __iomem *onenand_base)
+{
+ struct gpmc_timings t;
+
+ const int t_cer = 15;
+ const int t_avdp = 12;
+ const int t_aavdh = 7;
+ const int t_ce = 76;
+ const int t_aa = 76;
+ const int t_oe = 20;
+ const int t_cez = 20; /* max of t_cez, t_oez */
+ const int t_ds = 30;
+ const int t_wpl = 40;
+ const int t_wph = 30;
+
+ memset(&t, 0, sizeof(t));
+ t.sync_clk = 0;
+ t.cs_on = 0;
+ t.adv_on = 0;
+
+ /* Read */
+ t.adv_rd_off = gpmc_round_ns_to_ticks(max_t(int, t_avdp, t_cer));
+ t.oe_on = t.adv_rd_off + gpmc_round_ns_to_ticks(t_aavdh);
+ t.access = t.adv_on + gpmc_round_ns_to_ticks(t_aa);
+ t.access = max_t(int, t.access, t.cs_on + gpmc_round_ns_to_ticks(t_ce));
+ t.access = max_t(int, t.access, t.oe_on + gpmc_round_ns_to_ticks(t_oe));
+ t.oe_off = t.access + gpmc_round_ns_to_ticks(1);
+ t.cs_rd_off = t.oe_off;
+ t.rd_cycle = t.cs_rd_off + gpmc_round_ns_to_ticks(t_cez);
+
+ /* Write */
+ t.adv_wr_off = t.adv_rd_off;
+ t.we_on = t.oe_on;
+ if (cpu_is_omap34xx()) {
+ t.wr_data_mux_bus = t.we_on;
+ t.wr_access = t.we_on + gpmc_round_ns_to_ticks(t_ds);
+ }
+ t.we_off = t.we_on + gpmc_round_ns_to_ticks(t_wpl);
+ t.cs_wr_off = t.we_off + gpmc_round_ns_to_ticks(t_wph);
+ t.wr_cycle = t.cs_wr_off + gpmc_round_ns_to_ticks(t_cez);
+
+ /* Configure GPMC for asynchronous read */
+ gpmc_cs_write_reg(cs, GPMC_CS_CONFIG1,
+ GPMC_CONFIG1_DEVICESIZE_16 |
+ GPMC_CONFIG1_MUXADDDATA);
+
+ return gpmc_cs_set_timings(cs, &t);
+}
+
+static unsigned short omap2_onenand_readw(void __iomem *addr)
+{
+ return readw(addr);
+}
+
+static void omap2_onenand_writew(unsigned short value, void __iomem *addr)
+{
+ writew(value, addr);
+}
+
+static void set_onenand_cfg(void __iomem *onenand_base, int latency,
+ int sync_read, int sync_write, int hf)
+{
+ u32 reg;
+
+ reg = omap2_onenand_readw(onenand_base + ONENAND_REG_SYS_CFG1);
+ reg &= ~((0x7 << ONENAND_SYS_CFG1_BRL_SHIFT) | (0x7 << 9));
+ reg |= (latency << ONENAND_SYS_CFG1_BRL_SHIFT) |
+ ONENAND_SYS_CFG1_BL_16;
+ if (sync_read)
+ reg |= ONENAND_SYS_CFG1_SYNC_READ;
+ else
+ reg &= ~ONENAND_SYS_CFG1_SYNC_READ;
+ if (sync_write)
+ reg |= ONENAND_SYS_CFG1_SYNC_WRITE;
+ else
+ reg &= ~ONENAND_SYS_CFG1_SYNC_WRITE;
+ if (hf)
+ reg |= ONENAND_SYS_CFG1_HF;
+ else
+ reg &= ~ONENAND_SYS_CFG1_HF;
+ omap2_onenand_writew(reg, onenand_base + ONENAND_REG_SYS_CFG1);
+}
+
+static int omap2_onenand_set_sync_mode(struct omap_onenand_platform_data *cfg,
+ void __iomem *onenand_base,
+ int freq)
+{
+ struct gpmc_timings t;
+ const int t_cer = 15;
+ const int t_avdp = 12;
+ const int t_cez = 20; /* max of t_cez, t_oez */
+ const int t_ds = 30;
+ const int t_wpl = 40;
+ const int t_wph = 30;
+ int min_gpmc_clk_period, t_ces, t_avds, t_avdh, t_ach, t_aavdh, t_rdyo;
+ int tick_ns, div, fclk_offset_ns, fclk_offset, gpmc_clk_ns, latency;
+ int first_time = 0, hf = 0, sync_read = 0, sync_write = 0;
+ int err, ticks_cez;
+ int cs = cfg->cs;
+ u32 reg;
+
+ if (cfg->flags & ONENAND_SYNC_READ) {
+ sync_read = 1;
+ } else if (cfg->flags & ONENAND_SYNC_READWRITE) {
+ sync_read = 1;
+ sync_write = 1;
+ }
+
+ if (!freq) {
+ /* Very first call freq is not known */
+ err = omap2_onenand_set_async_mode(cs, onenand_base);
+ if (err)
+ return err;
+ reg = omap2_onenand_readw(onenand_base +
+ ONENAND_REG_VERSION_ID);
+ switch ((reg >> 4) & 0xf) {
+ case 0:
+ freq = 40;
+ break;
+ case 1:
+ freq = 54;
+ break;
+ case 2:
+ freq = 66;
+ break;
+ case 3:
+ freq = 83;
+ break;
+ case 4:
+ freq = 104;
+ break;
+ default:
+ freq = 54;
+ break;
+ }
+ first_time = 1;
+ }
+
+ switch (freq) {
+ case 83:
+ min_gpmc_clk_period = 12; /* 83 MHz */
+ t_ces = 5;
+ t_avds = 4;
+ t_avdh = 2;
+ t_ach = 6;
+ t_aavdh = 6;
+ t_rdyo = 9;
+ break;
+ case 66:
+ min_gpmc_clk_period = 15; /* 66 MHz */
+ t_ces = 6;
+ t_avds = 5;
+ t_avdh = 2;
+ t_ach = 6;
+ t_aavdh = 6;
+ t_rdyo = 11;
+ break;
+ default:
+ min_gpmc_clk_period = 18; /* 54 MHz */
+ t_ces = 7;
+ t_avds = 7;
+ t_avdh = 7;
+ t_ach = 9;
+ t_aavdh = 7;
+ t_rdyo = 15;
+ sync_write = 0;
+ break;
+ }
+
+ tick_ns = gpmc_ticks_to_ns(1);
+ div = gpmc_cs_calc_divider(cs, min_gpmc_clk_period);
+ gpmc_clk_ns = gpmc_ticks_to_ns(div);
+ if (gpmc_clk_ns < 15) /* >66Mhz */
+ hf = 1;
+ if (hf)
+ latency = 6;
+ else if (gpmc_clk_ns >= 25) /* 40 MHz*/
+ latency = 3;
+ else
+ latency = 4;
+
+ if (first_time)
+ set_onenand_cfg(onenand_base, latency,
+ sync_read, sync_write, hf);
+
+ if (div == 1) {
+ reg = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG2);
+ reg |= (1 << 7);
+ gpmc_cs_write_reg(cs, GPMC_CS_CONFIG2, reg);
+ reg = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG3);
+ reg |= (1 << 7);
+ gpmc_cs_write_reg(cs, GPMC_CS_CONFIG3, reg);
+ reg = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG4);
+ reg |= (1 << 7);
+ reg |= (1 << 23);
+ gpmc_cs_write_reg(cs, GPMC_CS_CONFIG4, reg);
+ } else {
+ reg = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG2);
+ reg &= ~(1 << 7);
+ gpmc_cs_write_reg(cs, GPMC_CS_CONFIG2, reg);
+ reg = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG3);
+ reg &= ~(1 << 7);
+ gpmc_cs_write_reg(cs, GPMC_CS_CONFIG3, reg);
+ reg = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG4);
+ reg &= ~(1 << 7);
+ reg &= ~(1 << 23);
+ gpmc_cs_write_reg(cs, GPMC_CS_CONFIG4, reg);
+ }
+
+ /* Set synchronous read timings */
+ memset(&t, 0, sizeof(t));
+ t.sync_clk = min_gpmc_clk_period;
+ t.cs_on = 0;
+ t.adv_on = 0;
+ fclk_offset_ns = gpmc_round_ns_to_ticks(max_t(int, t_ces, t_avds));
+ fclk_offset = gpmc_ns_to_ticks(fclk_offset_ns);
+ t.page_burst_access = gpmc_clk_ns;
+
+ /* Read */
+ t.adv_rd_off = gpmc_ticks_to_ns(fclk_offset + gpmc_ns_to_ticks(t_avdh));
+ t.oe_on = gpmc_ticks_to_ns(fclk_offset + gpmc_ns_to_ticks(t_ach));
+ t.access = gpmc_ticks_to_ns(fclk_offset + (latency + 1) * div);
+ t.oe_off = t.access + gpmc_round_ns_to_ticks(1);
+ t.cs_rd_off = t.oe_off;
+ ticks_cez = ((gpmc_ns_to_ticks(t_cez) + div - 1) / div) * div;
+ t.rd_cycle = gpmc_ticks_to_ns(fclk_offset + (latency + 1) * div +
+ ticks_cez);
+
+ /* Write */
+ if (sync_write) {
+ t.adv_wr_off = t.adv_rd_off;
+ t.we_on = 0;
+ t.we_off = t.cs_rd_off;
+ t.cs_wr_off = t.cs_rd_off;
+ t.wr_cycle = t.rd_cycle;
+ if (cpu_is_omap34xx()) {
+ t.wr_data_mux_bus = gpmc_ticks_to_ns(fclk_offset +
+ gpmc_ns_to_ticks(min_gpmc_clk_period +
+ t_rdyo));
+ t.wr_access = t.access;
+ }
+ } else {
+ t.adv_wr_off = gpmc_round_ns_to_ticks(max_t(int,
+ t_avdp, t_cer));
+ t.we_on = t.adv_wr_off + gpmc_round_ns_to_ticks(t_aavdh);
+ t.we_off = t.we_on + gpmc_round_ns_to_ticks(t_wpl);
+ t.cs_wr_off = t.we_off + gpmc_round_ns_to_ticks(t_wph);
+ t.wr_cycle = t.cs_wr_off + gpmc_round_ns_to_ticks(t_cez);
+ if (cpu_is_omap34xx()) {
+ t.wr_data_mux_bus = t.we_on;
+ t.wr_access = t.we_on + gpmc_round_ns_to_ticks(t_ds);
+ }
+ }
+
+ /* Configure GPMC for synchronous read */
+ gpmc_cs_write_reg(cs, GPMC_CS_CONFIG1,
+ GPMC_CONFIG1_WRAPBURST_SUPP |
+ GPMC_CONFIG1_READMULTIPLE_SUPP |
+ (sync_read ? GPMC_CONFIG1_READTYPE_SYNC : 0) |
+ (sync_write ? GPMC_CONFIG1_WRITEMULTIPLE_SUPP : 0) |
+ (sync_write ? GPMC_CONFIG1_WRITETYPE_SYNC : 0) |
+ GPMC_CONFIG1_CLKACTIVATIONTIME(fclk_offset) |
+ GPMC_CONFIG1_PAGE_LEN(2) |
+ (cpu_is_omap34xx() ? 0 :
+ (GPMC_CONFIG1_WAIT_READ_MON |
+ GPMC_CONFIG1_WAIT_PIN_SEL(0))) |
+ GPMC_CONFIG1_DEVICESIZE_16 |
+ GPMC_CONFIG1_DEVICETYPE_NOR |
+ GPMC_CONFIG1_MUXADDDATA);
+
+ err = gpmc_cs_set_timings(cs, &t);
+ if (err)
+ return err;
+
+ set_onenand_cfg(onenand_base, latency, sync_read, sync_write, hf);
+
+ return 0;
+}
+
+static int gpmc_onenand_setup(void __iomem *onenand_base, int freq)
+{
+ struct device *dev = &gpmc_onenand_device.dev;
+
+ /* Set sync timings in GPMC */
+ if (omap2_onenand_set_sync_mode(gpmc_onenand_data, onenand_base,
+ freq) < 0) {
+ dev_err(dev, "Unable to set synchronous mode\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+void __init gpmc_onenand_init(struct omap_onenand_platform_data *_onenand_data)
+{
+ gpmc_onenand_data = _onenand_data;
+ gpmc_onenand_data->onenand_setup = gpmc_onenand_setup;
+ gpmc_onenand_device.dev.platform_data = gpmc_onenand_data;
+
+ if (cpu_is_omap24xx() &&
+ (gpmc_onenand_data->flags & ONENAND_SYNC_READWRITE)) {
+ printk(KERN_ERR "Onenand using only SYNC_READ on 24xx\n");
+ gpmc_onenand_data->flags &= ~ONENAND_SYNC_READWRITE;
+ gpmc_onenand_data->flags |= ONENAND_SYNC_READ;
+ }
+
+ if (platform_device_register(&gpmc_onenand_device) < 0) {
+ printk(KERN_ERR "Unable to register OneNAND device\n");
+ return;
+ }
+}
diff --git a/arch/arm/plat-omap/include/mach/onenand.h b/arch/arm/plat-omap/include/mach/onenand.h
index 4649d30..94cde73 100644
--- a/arch/arm/plat-omap/include/mach/onenand.h
+++ b/arch/arm/plat-omap/include/mach/onenand.h
@@ -9,8 +9,14 @@
* published by the Free Software Foundation.
*/
+#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
+#ifndef __ASM_ARCH_OMAP_ONENAND_H__
+
+#define ONENAND_SYNC_READ (1 << 0)
+#define ONENAND_SYNC_READWRITE (1 << 1)
+
struct omap_onenand_platform_data {
int cs;
int gpio_irq;
@@ -18,8 +24,27 @@ struct omap_onenand_platform_data {
int nr_parts;
int (*onenand_setup)(void __iomem *, int freq);
int dma_channel;
+ u8 flags;
};
-int omap2_onenand_rephase(void);
-
#define ONENAND_MAX_PARTITIONS 8
+
+#if defined(CONFIG_MTD_ONENAND_OMAP2) || \
+ defined(CONFIG_MTD_ONENAND_OMAP2_MODULE)
+
+extern void gpmc_onenand_init(struct omap_onenand_platform_data *d);
+
+#else
+
+#define board_onenand_data NULL
+
+static inline void board_onenand_init(void)
+{
+}
+
+static inline void gpmc_onenand_init(struct omap_onenand_platform_data *d)
+{
+}
+
+#endif
+#endif
next prev parent reply other threads:[~2009-05-19 23:41 UTC|newest]
Thread overview: 37+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-05-19 23:30 [PATCH 00/10] Omap updates for merge window after 2.6.30 Tony Lindgren
2009-05-19 23:32 ` [PATCH 01/10] ARM: OMAP: Increase VMALLOC_END to allow 256MB RAM Tony Lindgren
2009-05-19 23:33 ` [PATCH 02/10] ARM: OMAP: McBSP: Fix legacy interrupts to clear their status Tony Lindgren
2009-05-19 23:34 ` [PATCH 03/10] ARM: OMAP: Update contact address of I2C registration helper Tony Lindgren
2009-05-25 9:23 ` Russell King - ARM Linux
2009-05-25 11:32 ` Jarkko Nikula
2009-05-25 16:23 ` Tony Lindgren
2009-05-19 23:36 ` [PATCH 04/10] ARM: OMAP1: Misc clean-up Tony Lindgren
2009-05-19 23:37 ` [PATCH 05/10] ARM: OMAP1: Make 770 LCD work Tony Lindgren
2009-05-25 9:29 ` Russell King - ARM Linux
2009-05-25 13:21 ` Andrew de Quincey
2009-05-25 16:40 ` Andrew de Quincey
2009-05-28 18:20 ` Tony Lindgren
2009-05-28 18:44 ` Andrew de Quincey
2009-05-28 19:11 ` [PATCH 05/10] ARM: OMAP1: Make 770 LCD work, v2 Tony Lindgren
2009-05-28 21:03 ` [PATCH 05/10] ARM: OMAP1: Make 770 LCD work, v3 Tony Lindgren
2009-05-28 19:50 ` [PATCH 05/10] ARM: OMAP1: Make 770 LCD work Russell King - ARM Linux
2009-05-29 0:29 ` Andrew de Quincey
2009-06-01 13:57 ` Kalle Valo
2009-05-28 19:53 ` Russell King - ARM Linux
2009-05-28 21:02 ` [PATCH] ARM: Move clk_add_alias() to arch/arm/common/clkdev.c (Re: [PATCH 05/10] ARM: OMAP1: Make 770 LCD work) Tony Lindgren
2009-06-03 16:44 ` Tony Lindgren
2009-05-19 23:38 ` [PATCH 06/10] ARM: OMAP2/3: DMA: implement trans copy and const fill Tony Lindgren
2009-05-19 23:40 ` [PATCH 07/10] ARM: OMAP2/3: sDMA: Correct omap_request_dma_chain() Tony Lindgren
2009-05-25 9:34 ` Russell King - ARM Linux
2009-05-25 9:40 ` Shilimkar, Santosh
2009-05-25 16:28 ` [PATCH 07/10] ARM: OMAP2/3: sDMA: Correct omap_request_dma_chain(), v2 Tony Lindgren
2009-05-26 4:55 ` Shilimkar, Santosh
2009-05-19 23:41 ` Tony Lindgren [this message]
2009-05-25 9:43 ` [PATCH 08/10] ARM: OMAP2/3: Add generic onenand support when connected to GPMC Russell King - ARM Linux
2009-05-25 16:50 ` [PATCH 08/10] ARM: OMAP2/3: Add generic onenand support when connected to GPMC, v2 Tony Lindgren
2009-05-19 23:42 ` [PATCH 09/10] ARM: OMAP2/3: Add generic smc91x support when connected to GPMC Tony Lindgren
2009-05-25 9:46 ` Russell King - ARM Linux
2009-05-25 16:59 ` [PATCH 09/10] ARM: OMAP2/3: Add generic smc91x support when connected to GPMC, v2 Tony Lindgren
2009-05-19 23:44 ` [PATCH 10/10] ARM: OMAP2: 2430SDP: Add FB support to board file Tony Lindgren
2009-05-25 17:42 ` [PATCH 11/10] ARM: OMAP: Add some entries to MAINTAINERS Tony Lindgren
2009-05-26 23:18 ` [PATCH 00/10] Omap updates for merge window after 2.6.30 Tony Lindgren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20090519234123.12760.11671.stgit@localhost \
--to=tony@atomide.com \
--cc=linux-arm-kernel@lists.arm.linux.org.uk \
--cc=linux-omap@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox