From: Tony Lindgren <tony@atomide.com>
To: linux-arm-kernel@lists.arm.linux.org.uk
Cc: linux-omap@vger.kernel.org
Subject: [PATCH 2/3] OMAP: Rename OMAP_MPUIO_BASE to OMAP1_MPUIO_BASE
Date: Thu, 06 Aug 2009 13:11:45 +0300 [thread overview]
Message-ID: <20090806101145.2569.24809.stgit@localhost> (raw)
In-Reply-To: <20090806100614.2569.8531.stgit@localhost>
Rename OMAP_MPUIO_BASE to OMAP1_MPUIO_BASE
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/plat-omap/gpio.c | 4 ++--
arch/arm/plat-omap/include/mach/gpio.h | 2 +-
drivers/input/keyboard/omap-keypad.c | 22 +++++++++++-----------
drivers/mtd/nand/ams-delta.c | 8 ++++----
4 files changed, 18 insertions(+), 18 deletions(-)
diff --git a/arch/arm/plat-omap/gpio.c b/arch/arm/plat-omap/gpio.c
index 59010e5..3b4b407 100644
--- a/arch/arm/plat-omap/gpio.c
+++ b/arch/arm/plat-omap/gpio.c
@@ -99,7 +99,7 @@
#define OMAP850_GPIO_INT_MASK 0x10
#define OMAP850_GPIO_INT_STATUS 0x14
-#define OMAP1_MPUIO_VBASE OMAP1_IO_ADDRESS(OMAP_MPUIO_BASE)
+#define OMAP1_MPUIO_VBASE OMAP1_IO_ADDRESS(OMAP1_MPUIO_BASE)
/*
* omap24xx specific GPIO registers
@@ -224,7 +224,7 @@ static struct gpio_bank gpio_bank_730[7] = {
#ifdef CONFIG_ARCH_OMAP850
static struct gpio_bank gpio_bank_850[7] = {
- { OMAP_MPUIO_BASE, INT_850_MPUIO, IH_MPUIO_BASE, METHOD_MPUIO },
+ { OMAP1_MPUIO_BASE, INT_850_MPUIO, IH_MPUIO_BASE, METHOD_MPUIO },
{ OMAP850_GPIO1_BASE, INT_850_GPIO_BANK1, IH_GPIO_BASE, METHOD_GPIO_850 },
{ OMAP850_GPIO2_BASE, INT_850_GPIO_BANK2, IH_GPIO_BASE + 32, METHOD_GPIO_850 },
{ OMAP850_GPIO3_BASE, INT_850_GPIO_BANK3, IH_GPIO_BASE + 64, METHOD_GPIO_850 },
diff --git a/arch/arm/plat-omap/include/mach/gpio.h b/arch/arm/plat-omap/include/mach/gpio.h
index 2b22a87..633ff68 100644
--- a/arch/arm/plat-omap/include/mach/gpio.h
+++ b/arch/arm/plat-omap/include/mach/gpio.h
@@ -29,7 +29,7 @@
#include <linux/io.h>
#include <mach/irqs.h>
-#define OMAP_MPUIO_BASE 0xfffb5000
+#define OMAP1_MPUIO_BASE 0xfffb5000
#if (defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850))
diff --git a/drivers/input/keyboard/omap-keypad.c b/drivers/input/keyboard/omap-keypad.c
index 87ec7b1..bba85ad 100644
--- a/drivers/input/keyboard/omap-keypad.c
+++ b/drivers/input/keyboard/omap-keypad.c
@@ -116,7 +116,7 @@ static irqreturn_t omap_kp_interrupt(int irq, void *dev_id)
}
} else
/* disable keyboard interrupt and schedule for handling */
- omap_writew(1, OMAP_MPUIO_BASE + OMAP_MPUIO_KBD_MASKIT);
+ omap_writew(1, OMAP1_MPUIO_BASE + OMAP_MPUIO_KBD_MASKIT);
tasklet_schedule(&kp_tasklet);
@@ -143,20 +143,20 @@ static void omap_kp_scan_keypad(struct omap_kp *omap_kp, unsigned char *state)
} else {
/* disable keyboard interrupt and schedule for handling */
- omap_writew(1, OMAP_MPUIO_BASE + OMAP_MPUIO_KBD_MASKIT);
+ omap_writew(1, OMAP1_MPUIO_BASE + OMAP_MPUIO_KBD_MASKIT);
/* read the keypad status */
- omap_writew(0xff, OMAP_MPUIO_BASE + OMAP_MPUIO_KBC);
+ omap_writew(0xff, OMAP1_MPUIO_BASE + OMAP_MPUIO_KBC);
for (col = 0; col < omap_kp->cols; col++) {
omap_writew(~(1 << col) & 0xff,
- OMAP_MPUIO_BASE + OMAP_MPUIO_KBC);
+ OMAP1_MPUIO_BASE + OMAP_MPUIO_KBC);
udelay(omap_kp->delay);
- state[col] = ~omap_readw(OMAP_MPUIO_BASE +
+ state[col] = ~omap_readw(OMAP1_MPUIO_BASE +
OMAP_MPUIO_KBR_LATCH) & 0xff;
}
- omap_writew(0x00, OMAP_MPUIO_BASE + OMAP_MPUIO_KBC);
+ omap_writew(0x00, OMAP1_MPUIO_BASE + OMAP_MPUIO_KBC);
udelay(2);
}
}
@@ -234,7 +234,7 @@ static void omap_kp_tasklet(unsigned long data)
for (i = 0; i < omap_kp_data->rows; i++)
enable_irq(gpio_to_irq(row_gpios[i]));
} else {
- omap_writew(0, OMAP_MPUIO_BASE + OMAP_MPUIO_KBD_MASKIT);
+ omap_writew(0, OMAP1_MPUIO_BASE + OMAP_MPUIO_KBD_MASKIT);
kp_cur_group = -1;
}
}
@@ -317,7 +317,7 @@ static int __devinit omap_kp_probe(struct platform_device *pdev)
/* Disable the interrupt for the MPUIO keyboard */
if (!cpu_is_omap24xx())
- omap_writew(1, OMAP_MPUIO_BASE + OMAP_MPUIO_KBD_MASKIT);
+ omap_writew(1, OMAP1_MPUIO_BASE + OMAP_MPUIO_KBD_MASKIT);
keymap = pdata->keymap;
@@ -391,7 +391,7 @@ static int __devinit omap_kp_probe(struct platform_device *pdev)
}
if (pdata->dbounce)
- omap_writew(0xff, OMAP_MPUIO_BASE + OMAP_MPUIO_GPIO_DEBOUNCING);
+ omap_writew(0xff, OMAP1_MPUIO_BASE + OMAP_MPUIO_GPIO_DEBOUNCING);
/* scan current status and enable interrupt */
omap_kp_scan_keypad(omap_kp, keypad_state);
@@ -402,7 +402,7 @@ static int __devinit omap_kp_probe(struct platform_device *pdev)
"omap-keypad", omap_kp) < 0)
goto err4;
}
- omap_writew(0, OMAP_MPUIO_BASE + OMAP_MPUIO_KBD_MASKIT);
+ omap_writew(0, OMAP1_MPUIO_BASE + OMAP_MPUIO_KBD_MASKIT);
} else {
for (irq_idx = 0; irq_idx < omap_kp->rows; irq_idx++) {
if (request_irq(gpio_to_irq(row_gpios[irq_idx]),
@@ -449,7 +449,7 @@ static int __devexit omap_kp_remove(struct platform_device *pdev)
free_irq(gpio_to_irq(row_gpios[i]), 0);
}
} else {
- omap_writew(1, OMAP_MPUIO_BASE + OMAP_MPUIO_KBD_MASKIT);
+ omap_writew(1, OMAP1_MPUIO_BASE + OMAP_MPUIO_KBD_MASKIT);
free_irq(omap_kp->irq, 0);
}
diff --git a/drivers/mtd/nand/ams-delta.c b/drivers/mtd/nand/ams-delta.c
index 782994e..005b91f 100644
--- a/drivers/mtd/nand/ams-delta.c
+++ b/drivers/mtd/nand/ams-delta.c
@@ -63,7 +63,7 @@ static void ams_delta_write_byte(struct mtd_info *mtd, u_char byte)
{
struct nand_chip *this = mtd->priv;
- omap_writew(0, (OMAP_MPUIO_BASE + OMAP_MPUIO_IO_CNTL));
+ omap_writew(0, (OMAP1_MPUIO_BASE + OMAP_MPUIO_IO_CNTL));
omap_writew(byte, this->IO_ADDR_W);
ams_delta_latch2_write(AMS_DELTA_LATCH2_NAND_NWE, 0);
ndelay(40);
@@ -78,7 +78,7 @@ static u_char ams_delta_read_byte(struct mtd_info *mtd)
ams_delta_latch2_write(AMS_DELTA_LATCH2_NAND_NRE, 0);
ndelay(40);
- omap_writew(~0, (OMAP_MPUIO_BASE + OMAP_MPUIO_IO_CNTL));
+ omap_writew(~0, (OMAP1_MPUIO_BASE + OMAP_MPUIO_IO_CNTL));
res = omap_readw(this->IO_ADDR_R);
ams_delta_latch2_write(AMS_DELTA_LATCH2_NAND_NRE,
AMS_DELTA_LATCH2_NAND_NRE);
@@ -178,8 +178,8 @@ static int __init ams_delta_init(void)
ams_delta_mtd->priv = this;
/* Set address of NAND IO lines */
- this->IO_ADDR_R = (OMAP_MPUIO_BASE + OMAP_MPUIO_INPUT_LATCH);
- this->IO_ADDR_W = (OMAP_MPUIO_BASE + OMAP_MPUIO_OUTPUT);
+ this->IO_ADDR_R = (OMAP1_MPUIO_BASE + OMAP_MPUIO_INPUT_LATCH);
+ this->IO_ADDR_W = (OMAP1_MPUIO_BASE + OMAP_MPUIO_OUTPUT);
this->read_byte = ams_delta_read_byte;
this->write_buf = ams_delta_write_buf;
this->read_buf = ams_delta_read_buf;
next prev parent reply other threads:[~2009-08-06 10:11 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-08-06 10:08 [PATCH 0/3] Omap header cleanup for upcoming 2.6.32 merge window Tony Lindgren
2009-08-06 10:10 ` [PATCH 1/3] OMAP: Remove OMAP_IO_ADDRESS, use OMAP1_IO_ADDRESS and OMAP2_IO_ADDRESS instead Tony Lindgren
2009-08-06 10:40 ` Felipe Balbi
2009-08-06 10:50 ` Tony Lindgren
2009-08-06 10:11 ` Tony Lindgren [this message]
2009-08-06 10:13 ` [PATCH 3/3] OMAP: Remove ifdefs for io.h Tony Lindgren
2009-08-06 11:01 ` [PATCH 0/3] Omap header cleanup for upcoming 2.6.32 merge window Russell King - ARM Linux
2009-08-06 11:11 ` Tony Lindgren
2009-08-11 9:28 ` git pull request for omap " Tony Lindgren
2009-08-24 13:05 ` [PATCH 0/3] Omap " Tony Lindgren
-- strict thread matches above, loose matches on Subject: below --
2009-06-23 14:52 [PATCH 0/3] Omap header cleanup for merge window after 2.6.31 Tony Lindgren
2009-06-23 14:53 ` [PATCH 2/3] OMAP: Rename OMAP_MPUIO_BASE to OMAP1_MPUIO_BASE Tony Lindgren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20090806101145.2569.24809.stgit@localhost \
--to=tony@atomide.com \
--cc=linux-arm-kernel@lists.arm.linux.org.uk \
--cc=linux-omap@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox