* [RFC] OMAP: DSS2: Add flag to enable/disable TVOUTBYPASS for VENC
@ 2009-09-18 14:19 y
0 siblings, 0 replies; 4+ messages in thread
From: y @ 2009-09-18 14:19 UTC (permalink / raw)
To: linux-omap; +Cc: tomi.valkeinen, Matthias Ludwig
From: Matthias Ludwig <mludwig@ultratronik.de>
Signed-off-by: Matthias Ludwig <mludwig@ultratronik.de>
---
OMAP CPU can only provide a level of about 0.8V at TVOUT, which is not
compliant with NTSC nor PAL. If one wants to have a compliant signal
external buffers need to be added. This requires TVOUTBYPASS to be set.
This patch implements a simple way to set it from dss platform data.
Is there a more elegant way to get register address?
arch/arm/plat-omap/include/mach/display.h | 1 +
drivers/video/omap2/dss/venc.c | 16 ++++++++++++++++
2 files changed, 17 insertions(+), 0 deletions(-)
diff --git a/arch/arm/plat-omap/include/mach/display.h b/arch/arm/plat-omap/include/mach/display.h
index 4c7422e..3013be0 100644
--- a/arch/arm/plat-omap/include/mach/display.h
+++ b/arch/arm/plat-omap/include/mach/display.h
@@ -380,6 +380,7 @@ struct omap_dss_device {
struct {
enum omap_dss_venc_type type;
bool invert_polarity;
+ bool bypass_tvout;
} venc;
} phy;
diff --git a/drivers/video/omap2/dss/venc.c b/drivers/video/omap2/dss/venc.c
index cf7827e..cb35a0d 100644
--- a/drivers/video/omap2/dss/venc.c
+++ b/drivers/video/omap2/dss/venc.c
@@ -35,6 +35,7 @@
#include <linux/regulator/consumer.h>
#include <mach/display.h>
+#include <mach/control.h>
#include <mach/cpu.h>
#include "dss.h"
@@ -532,6 +533,21 @@ static void venc_power_on(struct omap_dss_device *dssdev)
venc_write_reg(VENC_OUTPUT_CONTROL, l);
+ if (dssdev->phy.venc.bypass_tvout) {
+ u32 dc1, dc1_addr;
+#ifdef CONFIG_ARCH_OMAP3430
+ dc1_addr = OMAP343X_CTRL_REGADDR(OMAP343X_CONTROL_DEVCONF1);
+#elif defined(CONFIG_ARCH_OMAP2430)
+ dc1_addr = OMAP243X_CTRL_REGADDR(OMAP343X_CONTROL_DEVCONF1);
+#elif defined(CONFIG_ARCH_OMAP2420)
+ dc1_addr = OMAP242X_CTRL_REGADDR(OMAP343X_CONTROL_DEVCONF1);
+#else
+ bug();
+#endif
+ dc1 = readl(dc1_addr) | OMAP2_TVOUTBYPASS;
+ writel(dc1, dc1_addr);
+ }
+
dispc_set_digit_size(dssdev->panel.timings.x_res,
dssdev->panel.timings.y_res/2);
--
1.6.2.5
^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [RFC] OMAP: DSS2: Add flag to enable/disable TVOUTBYPASS for VENC
[not found] <1253283578-24377-1-git-send-email-y>
@ 2009-09-21 7:10 ` Tomi Valkeinen
2009-09-21 8:37 ` Matthias Ludwig
0 siblings, 1 reply; 4+ messages in thread
From: Tomi Valkeinen @ 2009-09-21 7:10 UTC (permalink / raw)
To: ext y@ultratronik.de; +Cc: linux-omap@vger.kernel.org, Matthias Ludwig
Hi,
On Fri, 2009-09-18 at 16:19 +0200, ext y@ultratronik.de wrote:
> From: Matthias Ludwig <mludwig@ultratronik.de>
>
> Signed-off-by: Matthias Ludwig <mludwig@ultratronik.de>
> ---
>
> OMAP CPU can only provide a level of about 0.8V at TVOUT, which is not
> compliant with NTSC nor PAL. If one wants to have a compliant signal
> external buffers need to be added. This requires TVOUTBYPASS to be set.
> This patch implements a simple way to set it from dss platform data.
>
> Is there a more elegant way to get register address?
Where does OMAP2_TVOUTBYPASS come from? It doesn't exist in my tree.
I have a hack in my board files that just do:
l = omap_ctrl_readl(OMAP343X_CONTROL_DEVCONF1) | (1 << 18);
omap_ctrl_writel(l, OMAP343X_CONTROL_DEVCONF1);
A flag in the omap_dss_device would be the proper way to do it, as you
did, but I think venc.c should call some function somewhere in arch/arm/
to actually do the setup.
Tomi
>
> arch/arm/plat-omap/include/mach/display.h | 1 +
> drivers/video/omap2/dss/venc.c | 16 ++++++++++++++++
> 2 files changed, 17 insertions(+), 0 deletions(-)
>
> diff --git a/arch/arm/plat-omap/include/mach/display.h b/arch/arm/plat-omap/include/mach/display.h
> index 4c7422e..3013be0 100644
> --- a/arch/arm/plat-omap/include/mach/display.h
> +++ b/arch/arm/plat-omap/include/mach/display.h
> @@ -380,6 +380,7 @@ struct omap_dss_device {
> struct {
> enum omap_dss_venc_type type;
> bool invert_polarity;
> + bool bypass_tvout;
> } venc;
> } phy;
>
> diff --git a/drivers/video/omap2/dss/venc.c b/drivers/video/omap2/dss/venc.c
> index cf7827e..cb35a0d 100644
> --- a/drivers/video/omap2/dss/venc.c
> +++ b/drivers/video/omap2/dss/venc.c
> @@ -35,6 +35,7 @@
> #include <linux/regulator/consumer.h>
>
> #include <mach/display.h>
> +#include <mach/control.h>
> #include <mach/cpu.h>
>
> #include "dss.h"
> @@ -532,6 +533,21 @@ static void venc_power_on(struct omap_dss_device *dssdev)
>
> venc_write_reg(VENC_OUTPUT_CONTROL, l);
>
> + if (dssdev->phy.venc.bypass_tvout) {
> + u32 dc1, dc1_addr;
> +#ifdef CONFIG_ARCH_OMAP3430
> + dc1_addr = OMAP343X_CTRL_REGADDR(OMAP343X_CONTROL_DEVCONF1);
> +#elif defined(CONFIG_ARCH_OMAP2430)
> + dc1_addr = OMAP243X_CTRL_REGADDR(OMAP343X_CONTROL_DEVCONF1);
> +#elif defined(CONFIG_ARCH_OMAP2420)
> + dc1_addr = OMAP242X_CTRL_REGADDR(OMAP343X_CONTROL_DEVCONF1);
> +#else
> + bug();
> +#endif
> + dc1 = readl(dc1_addr) | OMAP2_TVOUTBYPASS;
> + writel(dc1, dc1_addr);
> + }
> +
> dispc_set_digit_size(dssdev->panel.timings.x_res,
> dssdev->panel.timings.y_res/2);
>
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [RFC] OMAP: DSS2: Add flag to enable/disable TVOUTBYPASS for VENC
2009-09-21 7:10 ` [RFC] OMAP: DSS2: Add flag to enable/disable TVOUTBYPASS for VENC Tomi Valkeinen
@ 2009-09-21 8:37 ` Matthias Ludwig
2009-09-21 12:45 ` Tomi Valkeinen
0 siblings, 1 reply; 4+ messages in thread
From: Matthias Ludwig @ 2009-09-21 8:37 UTC (permalink / raw)
To: Tomi Valkeinen; +Cc: linux-omap@vger.kernel.org
> Where does OMAP2_TVOUTBYPASS come from? It doesn't exist in my tree.
Ohh, i missed that in the patch, sorry. I added to
arch/arm/plat-omap/include/mach/control.h (see new patch attached).
> A flag in the omap_dss_device would be the proper way to do it, as you
> did, but I think venc.c should call some function somewhere in arch/arm/
> to actually do the setup.
Where would you place this function?
best regards,
Matthias
---
arch/arm/plat-omap/include/mach/control.h | 1 +
arch/arm/plat-omap/include/mach/display.h | 1 +
drivers/video/omap2/dss/venc.c | 16 ++++++++++++++++
3 files changed, 18 insertions(+), 0 deletions(-)
diff --git a/arch/arm/plat-omap/include/mach/control.h b/arch/arm/plat-omap/include/mach/control.h
index 826d317..969d3bc 100644
--- a/arch/arm/plat-omap/include/mach/control.h
+++ b/arch/arm/plat-omap/include/mach/control.h
@@ -167,6 +167,7 @@
/* CONTROL_DEVCONF1 bits */
#define OMAP243X_MMC1_ACTIVE_OVERWRITE (1 << 31)
+#define OMAP2_TVOUTBYPASS (1 << 18)
#define OMAP2_MMCSDIO2ADPCLKISEL (1 << 6) /* MMC2 loop back clock */
#define OMAP2_MCBSP5_CLKS_MASK (1 << 4) /* > 242x */
#define OMAP2_MCBSP4_CLKS_MASK (1 << 2) /* > 242x */
diff --git a/arch/arm/plat-omap/include/mach/display.h b/arch/arm/plat-omap/include/mach/display.h
index 4c7422e..3013be0 100644
--- a/arch/arm/plat-omap/include/mach/display.h
+++ b/arch/arm/plat-omap/include/mach/display.h
@@ -380,6 +380,7 @@ struct omap_dss_device {
struct {
enum omap_dss_venc_type type;
bool invert_polarity;
+ bool bypass_tvout;
} venc;
} phy;
diff --git a/drivers/video/omap2/dss/venc.c b/drivers/video/omap2/dss/venc.c
index cf7827e..cb35a0d 100644
--- a/drivers/video/omap2/dss/venc.c
+++ b/drivers/video/omap2/dss/venc.c
@@ -35,6 +35,7 @@
#include <linux/regulator/consumer.h>
#include <mach/display.h>
+#include <mach/control.h>
#include <mach/cpu.h>
#include "dss.h"
@@ -532,6 +533,21 @@ static void venc_power_on(struct omap_dss_device *dssdev)
venc_write_reg(VENC_OUTPUT_CONTROL, l);
+ if (dssdev->phy.venc.bypass_tvout) {
+ u32 dc1, dc1_addr;
+#ifdef CONFIG_ARCH_OMAP3430
+ dc1_addr = OMAP343X_CTRL_REGADDR(OMAP343X_CONTROL_DEVCONF1);
+#elif defined(CONFIG_ARCH_OMAP2430)
+ dc1_addr = OMAP243X_CTRL_REGADDR(OMAP343X_CONTROL_DEVCONF1);
+#elif defined(CONFIG_ARCH_OMAP2420)
+ dc1_addr = OMAP242X_CTRL_REGADDR(OMAP343X_CONTROL_DEVCONF1);
+#else
+ bug();
+#endif
+ dc1 = readl(dc1_addr) | OMAP2_TVOUTBYPASS;
+ writel(dc1, dc1_addr);
+ }
+
dispc_set_digit_size(dssdev->panel.timings.x_res,
dssdev->panel.timings.y_res/2);
^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [RFC] OMAP: DSS2: Add flag to enable/disable TVOUTBYPASS for VENC
2009-09-21 8:37 ` Matthias Ludwig
@ 2009-09-21 12:45 ` Tomi Valkeinen
0 siblings, 0 replies; 4+ messages in thread
From: Tomi Valkeinen @ 2009-09-21 12:45 UTC (permalink / raw)
To: ext Matthias Ludwig; +Cc: linux-omap@vger.kernel.org
On Mon, 2009-09-21 at 10:37 +0200, ext Matthias Ludwig wrote:
> > Where does OMAP2_TVOUTBYPASS come from? It doesn't exist in my tree.
>
> Ohh, i missed that in the patch, sorry. I added to
> arch/arm/plat-omap/include/mach/control.h (see new patch attached).
>
> > A flag in the omap_dss_device would be the proper way to do it, as you
> > did, but I think venc.c should call some function somewhere in arch/arm/
> > to actually do the setup.
>
> Where would you place this function?
That I cannot say. Quick grep shows that there are multiple files in
plat-omap/ and mach-omap2/ handling CONTROL registers. None of those
files looked right for DSS, so perhaps there's need for another file for
DSS. But I have to say I haven't studied this problem at all, so I'm
just guessing here. Board file is of course safe place for the code for
now, but a better solution would be nice.
Tomi
>
> best regards,
> Matthias
>
> ---
> arch/arm/plat-omap/include/mach/control.h | 1 +
> arch/arm/plat-omap/include/mach/display.h | 1 +
> drivers/video/omap2/dss/venc.c | 16 ++++++++++++++++
> 3 files changed, 18 insertions(+), 0 deletions(-)
>
> diff --git a/arch/arm/plat-omap/include/mach/control.h b/arch/arm/plat-omap/include/mach/control.h
> index 826d317..969d3bc 100644
> --- a/arch/arm/plat-omap/include/mach/control.h
> +++ b/arch/arm/plat-omap/include/mach/control.h
> @@ -167,6 +167,7 @@
>
> /* CONTROL_DEVCONF1 bits */
> #define OMAP243X_MMC1_ACTIVE_OVERWRITE (1 << 31)
> +#define OMAP2_TVOUTBYPASS (1 << 18)
> #define OMAP2_MMCSDIO2ADPCLKISEL (1 << 6) /* MMC2 loop back clock */
> #define OMAP2_MCBSP5_CLKS_MASK (1 << 4) /* > 242x */
> #define OMAP2_MCBSP4_CLKS_MASK (1 << 2) /* > 242x */
> diff --git a/arch/arm/plat-omap/include/mach/display.h b/arch/arm/plat-omap/include/mach/display.h
> index 4c7422e..3013be0 100644
> --- a/arch/arm/plat-omap/include/mach/display.h
> +++ b/arch/arm/plat-omap/include/mach/display.h
> @@ -380,6 +380,7 @@ struct omap_dss_device {
> struct {
> enum omap_dss_venc_type type;
> bool invert_polarity;
> + bool bypass_tvout;
> } venc;
> } phy;
>
> diff --git a/drivers/video/omap2/dss/venc.c b/drivers/video/omap2/dss/venc.c
> index cf7827e..cb35a0d 100644
> --- a/drivers/video/omap2/dss/venc.c
> +++ b/drivers/video/omap2/dss/venc.c
> @@ -35,6 +35,7 @@
> #include <linux/regulator/consumer.h>
>
> #include <mach/display.h>
> +#include <mach/control.h>
> #include <mach/cpu.h>
>
> #include "dss.h"
> @@ -532,6 +533,21 @@ static void venc_power_on(struct omap_dss_device *dssdev)
>
> venc_write_reg(VENC_OUTPUT_CONTROL, l);
>
> + if (dssdev->phy.venc.bypass_tvout) {
> + u32 dc1, dc1_addr;
> +#ifdef CONFIG_ARCH_OMAP3430
> + dc1_addr = OMAP343X_CTRL_REGADDR(OMAP343X_CONTROL_DEVCONF1);
> +#elif defined(CONFIG_ARCH_OMAP2430)
> + dc1_addr = OMAP243X_CTRL_REGADDR(OMAP343X_CONTROL_DEVCONF1);
> +#elif defined(CONFIG_ARCH_OMAP2420)
> + dc1_addr = OMAP242X_CTRL_REGADDR(OMAP343X_CONTROL_DEVCONF1);
> +#else
> + bug();
> +#endif
> + dc1 = readl(dc1_addr) | OMAP2_TVOUTBYPASS;
> + writel(dc1, dc1_addr);
> + }
> +
> dispc_set_digit_size(dssdev->panel.timings.x_res,
> dssdev->panel.timings.y_res/2);
>
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2009-09-21 12:47 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <1253283578-24377-1-git-send-email-y>
2009-09-21 7:10 ` [RFC] OMAP: DSS2: Add flag to enable/disable TVOUTBYPASS for VENC Tomi Valkeinen
2009-09-21 8:37 ` Matthias Ludwig
2009-09-21 12:45 ` Tomi Valkeinen
2009-09-18 14:19 y
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox