* [PATCH v2 0/8] introduce 3630 boards
@ 2009-11-10 22:47 Vikram Pandita
2009-11-10 22:47 ` [PATCH v2 1/8] omap: 3630: update is_chip variable Vikram Pandita
` (2 more replies)
0 siblings, 3 replies; 16+ messages in thread
From: Vikram Pandita @ 2009-11-10 22:47 UTC (permalink / raw)
To: linux-omap; +Cc: Vikram Pandita
Introducing 3630 boards: zoom3 and sdp3630
The peripherals are very similar for the two bards as per this discussion:
http://marc.info/?l=linux-omap&m=125676595710748&w=2
So maximum reuse is done for the board files for zoom3 and sdp3630
V1: Review comments incorporated:
http://marc.info/?l=linux-omap&m=125632676504364&w=2
http://marc.info/?l=linux-omap&m=125632720804869&w=2
http://marc.info/?l=linux-omap&m=125633994320138&w=2
V2: Review comments by Nishanth Menon
http://marc.info/?l=linux-omap&m=125728617825678&w=2
http://marc.info/?l=linux-omap&m=125728665226332&w=2
http://marc.info/?l=linux-omap&m=125728729027309&w=2
http://marc.info/?l=linux-omap&m=125728749327603&w=2
Vikram Pandita (8):
omap: 3630: update is_chip variable
omap: DEBUG_LL: allow no omap uart configuration
omap: zoom2: split board file for reuse
omap: zoom2: update defconfig
omap: zoom3: introduce zoom3 board support
omap: zoom3: defconfig creation
omap: 3630sdp: introduce 3630 sdp board support
omap: 3630sdp: defconfig creation
arch/arm/configs/omap_3630sdp_defconfig | 1606 ++++++++++++++++++++
arch/arm/configs/omap_zoom2_defconfig | 231 ++--
arch/arm/configs/omap_zoom3_defconfig | 1605 +++++++++++++++++++
arch/arm/mach-omap2/Kconfig | 8 +
arch/arm/mach-omap2/Makefile | 8 +
arch/arm/mach-omap2/board-3630sdp.c | 96 ++
arch/arm/mach-omap2/board-zoom-peripherals.c | 403 +++++
arch/arm/mach-omap2/board-zoom2.c | 261 +---
arch/arm/mach-omap2/board-zoom3.c | 59 +
arch/arm/mach-omap2/id.c | 2 +
arch/arm/mach-omap2/sdram-hynix-h8mbx00u0mer-0em.h | 52 +
arch/arm/plat-omap/Kconfig | 3 +
arch/arm/plat-omap/include/plat/cpu.h | 7 +-
arch/arm/plat-omap/include/plat/uncompress.h | 4 +-
14 files changed, 4005 insertions(+), 340 deletions(-)
create mode 100644 arch/arm/configs/omap_3630sdp_defconfig
create mode 100644 arch/arm/configs/omap_zoom3_defconfig
create mode 100755 arch/arm/mach-omap2/board-3630sdp.c
create mode 100644 arch/arm/mach-omap2/board-zoom-peripherals.c
create mode 100644 arch/arm/mach-omap2/board-zoom3.c
create mode 100644 arch/arm/mach-omap2/sdram-hynix-h8mbx00u0mer-0em.h
^ permalink raw reply [flat|nested] 16+ messages in thread* [PATCH v2 1/8] omap: 3630: update is_chip variable 2009-11-10 22:47 [PATCH v2 0/8] introduce 3630 boards Vikram Pandita @ 2009-11-10 22:47 ` Vikram Pandita 2009-11-10 22:47 ` [PATCH v2 2/8] omap: introduce OMAP_LL_DEBUG_NONE DEBUG_LL config Vikram Pandita 2009-11-11 1:27 ` [APPLIED] [PATCH v2 1/8] omap: 3630: update is_chip variable Tony Lindgren 2009-11-11 15:15 ` [PATCH v2 0/8] introduce 3630 boards Gadiyar, Anand 2009-11-11 15:19 ` Gadiyar, Anand 2 siblings, 2 replies; 16+ messages in thread From: Vikram Pandita @ 2009-11-10 22:47 UTC (permalink / raw) To: linux-omap; +Cc: Vikram Pandita 3630 is getting treated like next rev of 3430 omap_chip.oc variable has to be updated for 3630 version Otherwise the Core power domain is not getting registered. This gets used in the registration of power domains in: "arch/arm/mach-omap2/powerdomains34xx.h" core_34xx_es3_1_pwrdm OMAP_CHIP_INIT(CHIP_GE_OMAP3430ES3_1) Core power doman will get registered for 3630 only when .oc is pouplated correctly. Tested on Zoom3(3630) board Signed-off-by: Vikram Pandita <vikram.pandita@ti.com> Acked-by: Alexander Shishkin <virtuoso@slind.org> Acked-by: Ari Kauppi <kauppi@papupata.org> Acked-by: Nishanth Menon <nm@ti.com> --- arch/arm/mach-omap2/id.c | 2 ++ arch/arm/plat-omap/include/plat/cpu.h | 7 +++++-- 2 files changed, 7 insertions(+), 2 deletions(-) diff --git a/arch/arm/mach-omap2/id.c b/arch/arm/mach-omap2/id.c index 1c15112..189cf7a 100644 --- a/arch/arm/mach-omap2/id.c +++ b/arch/arm/mach-omap2/id.c @@ -359,6 +359,8 @@ void __init omap2_check_revision(void) omap_chip.oc |= CHIP_IS_OMAP3430ES3_0; else if (omap_rev() == OMAP3430_REV_ES3_1) omap_chip.oc |= CHIP_IS_OMAP3430ES3_1; + else if (omap_rev() == OMAP3630_REV_ES1_0) + omap_chip.oc |= CHIP_IS_OMAP3630ES1; } else { pr_err("Uninitialized omap_chip, please fix!\n"); } diff --git a/arch/arm/plat-omap/include/plat/cpu.h b/arch/arm/plat-omap/include/plat/cpu.h index 7cb0556..05a0a33 100644 --- a/arch/arm/plat-omap/include/plat/cpu.h +++ b/arch/arm/plat-omap/include/plat/cpu.h @@ -454,6 +454,7 @@ IS_OMAP_TYPE(3430, 0x3430) #define CHIP_IS_OMAP3430ES2 (1 << 4) #define CHIP_IS_OMAP3430ES3_0 (1 << 5) #define CHIP_IS_OMAP3430ES3_1 (1 << 6) +#define CHIP_IS_OMAP3630ES1 (1 << 7) #define CHIP_IS_OMAP24XX (CHIP_IS_OMAP2420 | CHIP_IS_OMAP2430) @@ -465,8 +466,10 @@ IS_OMAP_TYPE(3430, 0x3430) */ #define CHIP_GE_OMAP3430ES2 (CHIP_IS_OMAP3430ES2 | \ CHIP_IS_OMAP3430ES3_0 | \ - CHIP_IS_OMAP3430ES3_1) -#define CHIP_GE_OMAP3430ES3_1 (CHIP_IS_OMAP3430ES3_1) + CHIP_IS_OMAP3430ES3_1 | \ + CHIP_IS_OMAP3630ES1) +#define CHIP_GE_OMAP3430ES3_1 (CHIP_IS_OMAP3430ES3_1 | \ + CHIP_IS_OMAP3630ES1) int omap_chip_is(struct omap_chip_id oci); -- 1.6.5.1.69.g36942 ^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH v2 2/8] omap: introduce OMAP_LL_DEBUG_NONE DEBUG_LL config 2009-11-10 22:47 ` [PATCH v2 1/8] omap: 3630: update is_chip variable Vikram Pandita @ 2009-11-10 22:47 ` Vikram Pandita 2009-11-10 22:47 ` [PATCH v2 3/8] omap: zoom2: split board file for software reuse Vikram Pandita 2009-11-11 1:32 ` [APPLIED] [PATCH v2 2/8] omap: introduce OMAP_LL_DEBUG_NONE DEBUG_LL config Tony Lindgren 2009-11-11 1:27 ` [APPLIED] [PATCH v2 1/8] omap: 3630: update is_chip variable Tony Lindgren 1 sibling, 2 replies; 16+ messages in thread From: Vikram Pandita @ 2009-11-10 22:47 UTC (permalink / raw) To: linux-omap; +Cc: Vikram Pandita Zoom2/Zoom3 kind of boards do not use omap uarts for console. These use external debug board for console. So these boards should not have "Uncompressing Kernel...." log put on omap uarts. By interoducing OMAP_LL_DEBUG_NONE option, unnecessary writes to omap uarts is avoided. In future, the DEBUG_LL interface will be enhanced to use external debug board. Signed-off-by: Vikram Pandita <vikram.pandita@ti.com> --- arch/arm/plat-omap/Kconfig | 5 ++++- arch/arm/plat-omap/include/plat/uncompress.h | 6 +++++- 2 files changed, 9 insertions(+), 2 deletions(-) diff --git a/arch/arm/plat-omap/Kconfig b/arch/arm/plat-omap/Kconfig index 64b3f52..f348ddf 100644 --- a/arch/arm/plat-omap/Kconfig +++ b/arch/arm/plat-omap/Kconfig @@ -165,7 +165,7 @@ config OMAP_DM_TIMER choice prompt "Low-level debug console UART" depends on ARCH_OMAP - default OMAP_LL_DEBUG_UART1 + default OMAP_LL_DEBUG_NONE config OMAP_LL_DEBUG_UART1 bool "UART1" @@ -176,6 +176,9 @@ config OMAP_LL_DEBUG_UART2 config OMAP_LL_DEBUG_UART3 bool "UART3" +config OMAP_LL_DEBUG_NONE + bool "None" + endchoice config OMAP_SERIAL_WAKE diff --git a/arch/arm/plat-omap/include/plat/uncompress.h b/arch/arm/plat-omap/include/plat/uncompress.h index e22f575..13c305d 100644 --- a/arch/arm/plat-omap/include/plat/uncompress.h +++ b/arch/arm/plat-omap/include/plat/uncompress.h @@ -44,8 +44,12 @@ static void putc(int c) uart = (volatile u8 *)(OMAP_UART3_BASE); #elif defined(CONFIG_OMAP_LL_DEBUG_UART2) uart = (volatile u8 *)(OMAP_UART2_BASE); -#else +#elif defined(CONFIG_OMAP_LL_DEBUG_UART1) uart = (volatile u8 *)(OMAP_UART1_BASE); +#elif defined(CONFIG_OMAP_LL_DEBUG_NONE) + return; +#else + return; #endif #ifdef CONFIG_ARCH_OMAP1 -- 1.6.5.1.69.g36942 ^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH v2 3/8] omap: zoom2: split board file for software reuse 2009-11-10 22:47 ` [PATCH v2 2/8] omap: introduce OMAP_LL_DEBUG_NONE DEBUG_LL config Vikram Pandita @ 2009-11-10 22:47 ` Vikram Pandita 2009-11-10 22:47 ` [PATCH v2 4/8] omap: zoom2: update defconfig for LL_DEBUG_NONE Vikram Pandita 2009-11-11 1:24 ` [PATCH v2 3/8] omap: zoom2: split board file for software reuse Tony Lindgren 2009-11-11 1:32 ` [APPLIED] [PATCH v2 2/8] omap: introduce OMAP_LL_DEBUG_NONE DEBUG_LL config Tony Lindgren 1 sibling, 2 replies; 16+ messages in thread From: Vikram Pandita @ 2009-11-10 22:47 UTC (permalink / raw) To: linux-omap; +Cc: Vikram Pandita Split zoom2 board file into: base board file and a board-zoom-peripherals.c file that way the same peripherals file can be reused for: zoom3 and sdp3630 Following list shows the commonality across the three platforms and hence the case for software reuse: Peripheral zoom2 zoom3 sdp3630 --------------------------------------- Ethernet smsc smsc smc NOR n/a n/a B Onenand n/a n/a B HDMI A A B (present on different i2c) NAND A A A (same nand) SDRAM A A A (same sdram) Keypad A A A (same twl) Camera A A A (same sensor can be mounted) LCD Display A A A (same wvga display) OPPs A A A (same chip feature) Audio A A A (same audio via twl5030) Signed-off-by: Vikram Pandita <vikram.pandita@ti.com> --- arch/arm/mach-omap2/Makefile | 1 + arch/arm/mach-omap2/board-zoom-peripherals.c | 278 ++++++++++++++++++++++++++ arch/arm/mach-omap2/board-zoom2.c | 247 +---------------------- 3 files changed, 286 insertions(+), 240 deletions(-) create mode 100644 arch/arm/mach-omap2/board-zoom-peripherals.c diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index 03cb4fc..4d66b42 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -72,6 +72,7 @@ obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51.o \ board-rx51-peripherals.o \ mmc-twl4030.o obj-$(CONFIG_MACH_OMAP_ZOOM2) += board-zoom2.o \ + board-zoom-peripherals.o \ mmc-twl4030.o \ board-zoom-debugboard.o obj-$(CONFIG_MACH_CM_T35) += board-cm-t35.o \ diff --git a/arch/arm/mach-omap2/board-zoom-peripherals.c b/arch/arm/mach-omap2/board-zoom-peripherals.c new file mode 100644 index 0000000..d872588 --- /dev/null +++ b/arch/arm/mach-omap2/board-zoom-peripherals.c @@ -0,0 +1,278 @@ +/* + * Copyright (C) 2009 Texas Instruments Inc. + * + * Modified from mach-omap2/board-zoom2.c + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/input.h> +#include <linux/input/matrix_keypad.h> +#include <linux/gpio.h> +#include <linux/i2c/twl4030.h> +#include <linux/regulator/machine.h> + +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <asm/mach/map.h> + +#include <plat/common.h> +#include <plat/usb.h> + +#include "mmc-twl4030.h" + +/* Zoom2 has Qwerty keyboard*/ +static int zoom_board_keymap[] = { + KEY(0, 0, KEY_E), + KEY(1, 0, KEY_R), + KEY(2, 0, KEY_T), + KEY(3, 0, KEY_HOME), + KEY(6, 0, KEY_I), + KEY(7, 0, KEY_LEFTSHIFT), + KEY(0, 1, KEY_D), + KEY(1, 1, KEY_F), + KEY(2, 1, KEY_G), + KEY(3, 1, KEY_SEND), + KEY(6, 1, KEY_K), + KEY(7, 1, KEY_ENTER), + KEY(0, 2, KEY_X), + KEY(1, 2, KEY_C), + KEY(2, 2, KEY_V), + KEY(3, 2, KEY_END), + KEY(6, 2, KEY_DOT), + KEY(7, 2, KEY_CAPSLOCK), + KEY(0, 3, KEY_Z), + KEY(1, 3, KEY_KPPLUS), + KEY(2, 3, KEY_B), + KEY(3, 3, KEY_F1), + KEY(6, 3, KEY_O), + KEY(7, 3, KEY_SPACE), + KEY(0, 4, KEY_W), + KEY(1, 4, KEY_Y), + KEY(2, 4, KEY_U), + KEY(3, 4, KEY_F2), + KEY(4, 4, KEY_VOLUMEUP), + KEY(6, 4, KEY_L), + KEY(7, 4, KEY_LEFT), + KEY(0, 5, KEY_S), + KEY(1, 5, KEY_H), + KEY(2, 5, KEY_J), + KEY(3, 5, KEY_F3), + KEY(5, 5, KEY_VOLUMEDOWN), + KEY(6, 5, KEY_M), + KEY(4, 5, KEY_ENTER), + KEY(7, 5, KEY_RIGHT), + KEY(0, 6, KEY_Q), + KEY(1, 6, KEY_A), + KEY(2, 6, KEY_N), + KEY(3, 6, KEY_BACKSPACE), + KEY(6, 6, KEY_P), + KEY(7, 6, KEY_UP), + KEY(6, 7, KEY_SELECT), + KEY(7, 7, KEY_DOWN), + KEY(0, 7, KEY_PROG1), /*MACRO 1 <User defined> */ + KEY(1, 7, KEY_PROG2), /*MACRO 2 <User defined> */ + KEY(2, 7, KEY_PROG3), /*MACRO 3 <User defined> */ + KEY(3, 7, KEY_PROG4), /*MACRO 4 <User defined> */ + 0 +}; + +static struct matrix_keymap_data zoom_board_map_data = { + .keymap = zoom_board_keymap, + .keymap_size = ARRAY_SIZE(zoom_board_keymap), +}; + +static struct twl4030_keypad_data zoom_kp_twl4030_data = { + .keymap_data = &zoom_board_map_data, + .rows = 8, + .cols = 8, + .rep = 1, +}; + +static struct twl4030_madc_platform_data zoom_madc_data = { + .irq_line = 1, +}; + +static struct twl4030_hsmmc_info zoom_mmc[] = { + { + .name = "external", + .mmc = 1, + .wires = 4, + .cover_only = true, + .gpio_cd = -EINVAL, + .gpio_wp = -EINVAL, + .power_saving = true, + }, + { + .name = "internal", + .mmc = 2, + .wires = 8, + .gpio_cd = -EINVAL, + .gpio_wp = -EINVAL, + .nonremovable = true, + .power_saving = true, + }, + {} /* Terminator */ +}; + +static struct regulator_consumer_supply zoom_vmmc1_supply = { + .supply = "vmmc", +}; + +static struct regulator_consumer_supply zoom_vmmc2_supply = { + .supply = "vmmc", +}; + +static struct regulator_consumer_supply zoom_vsim_supply = { + .supply = "vmmc_aux", +}; + +/* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */ +static struct regulator_init_data zoom_vmmc1 = { + .constraints = { + .min_uV = 1850000, + .max_uV = 3150000, + .valid_modes_mask = REGULATOR_MODE_NORMAL + | REGULATOR_MODE_STANDBY, + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE + | REGULATOR_CHANGE_MODE + | REGULATOR_CHANGE_STATUS, + }, + .num_consumer_supplies = 1, + .consumer_supplies = &zoom_vmmc1_supply, +}; + +/* VMMC2 for MMC2 card */ +static struct regulator_init_data zoom_vmmc2 = { + .constraints = { + .name = "VMMC2_30", + .min_uV = 1850000, + .max_uV = 1850000, + .apply_uV = true, + .valid_modes_mask = REGULATOR_MODE_NORMAL + | REGULATOR_MODE_STANDBY, + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE + | REGULATOR_CHANGE_MODE + | REGULATOR_CHANGE_STATUS, + }, + .num_consumer_supplies = 1, + .consumer_supplies = &zoom_vmmc2_supply, +}; + +/* VSIM for OMAP VDD_MMC1A (i/o for DAT4..DAT7) */ +static struct regulator_init_data zoom_vsim = { + .constraints = { + .name = "VMMC2_IO_18", + .min_uV = 1800000, + .max_uV = 3000000, + .apply_uV = true, + .valid_modes_mask = REGULATOR_MODE_NORMAL + | REGULATOR_MODE_STANDBY, + .valid_ops_mask = REGULATOR_CHANGE_MODE + | REGULATOR_CHANGE_STATUS, + }, + .num_consumer_supplies = 1, + .consumer_supplies = &zoom_vsim_supply, +}; + +static int zoom_twl_gpio_setup(struct device *dev, + unsigned gpio, unsigned ngpio) +{ + /* gpio + 0 is "mmc0_cd" (input/IRQ), + * gpio + 1 is "mmc1_cd" (input/IRQ) + */ + zoom_mmc[0].gpio_cd = gpio + 0; + zoom_mmc[1].gpio_cd = gpio + 1; + twl4030_mmc_init(zoom_mmc); + + /* link regulators to MMC adapters ... we "know" the + * regulators will be set up only *after* we return. + */ + zoom_vmmc1_supply.dev = zoom_mmc[0].dev; + zoom_vmmc2_supply.dev = zoom_mmc[1].dev; + zoom_vsim_supply.dev = zoom_mmc[0].dev; + + return 0; +} + +static struct twl4030_gpio_platform_data zoom_gpio_data = { + .gpio_base = OMAP_MAX_GPIO_LINES, + .irq_base = TWL4030_GPIO_IRQ_BASE, + .irq_end = TWL4030_GPIO_IRQ_END, + .setup = zoom_twl_gpio_setup, +}; + +static struct twl4030_usb_data zoom_usb_data = { + .usb_mode = T2_USB_MODE_ULPI, +}; + +static int zoom_batt_table[] = { +/* 0 C*/ +30800, 29500, 28300, 27100, +26000, 24900, 23900, 22900, 22000, 21100, 20300, 19400, 18700, 17900, +17200, 16500, 15900, 15300, 14700, 14100, 13600, 13100, 12600, 12100, +11600, 11200, 10800, 10400, 10000, 9630, 9280, 8950, 8620, 8310, +8020, 7730, 7460, 7200, 6950, 6710, 6470, 6250, 6040, 5830, +5640, 5450, 5260, 5090, 4920, 4760, 4600, 4450, 4310, 4170, +4040, 3910, 3790, 3670, 3550 +}; + +static struct twl4030_bci_platform_data zoom_bci_data = { + .battery_tmp_tbl = zoom_batt_table, + .tblsize = ARRAY_SIZE(zoom_batt_table), +}; + +static struct twl4030_platform_data zoom_twldata = { + .irq_base = TWL4030_IRQ_BASE, + .irq_end = TWL4030_IRQ_END, + + /* platform_data for children goes here */ + .bci = &zoom_bci_data, + .madc = &zoom_madc_data, + .usb = &zoom_usb_data, + .gpio = &zoom_gpio_data, + .keypad = &zoom_kp_twl4030_data, + .vmmc1 = &zoom_vmmc1, + .vmmc2 = &zoom_vmmc2, + .vsim = &zoom_vsim, +}; + +static struct i2c_board_info __initdata zoom_i2c_boardinfo[] = { + { + I2C_BOARD_INFO("twl5030", 0x48), + .flags = I2C_CLIENT_WAKE, + .irq = INT_34XX_SYS_NIRQ, + .platform_data = &zoom_twldata, + }, +}; + +static int __init zoom_i2c_init(void) +{ + omap_register_i2c_bus(1, 2200, zoom_i2c_boardinfo, + ARRAY_SIZE(zoom_i2c_boardinfo)); + + /* TODO: I2C2 on zoom2/3: + * Add Synaptic RMI controller + * Add Camera sensor IMX046 + * Add Camera sensor LV8093 + */ + omap_register_i2c_bus(2, 100, NULL, 0); + + /* TODO: I2C3 on Zoom2/3: + * Add: SIL9022 HDMI + */ + omap_register_i2c_bus(3, 100, NULL, 0); + return 0; +} + +void __init zoom_peripherals_init(void) +{ + zoom_i2c_init(); + omap_serial_init(); + usb_musb_init(); +} diff --git a/arch/arm/mach-omap2/board-zoom2.c b/arch/arm/mach-omap2/board-zoom2.c index 4ad9b94..1330915 100644 --- a/arch/arm/mach-omap2/board-zoom2.c +++ b/arch/arm/mach-omap2/board-zoom2.c @@ -1,8 +1,6 @@ /* * Copyright (C) 2009 Texas Instruments Inc. - * Mikkel Christensen <mlc@ti.com> * - * Modified from mach-omap2/board-ldp.c * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as @@ -13,203 +11,24 @@ #include <linux/init.h> #include <linux/platform_device.h> #include <linux/input.h> -#include <linux/input/matrix_keypad.h> #include <linux/gpio.h> -#include <linux/i2c/twl4030.h> -#include <linux/regulator/machine.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> #include <plat/common.h> -#include <plat/usb.h> +#include <plat/board.h> -#include "mmc-twl4030.h" #include "sdram-micron-mt46h32m32lf-6.h" -/* Zoom2 has Qwerty keyboard*/ -static int board_keymap[] = { - KEY(0, 0, KEY_E), - KEY(1, 0, KEY_R), - KEY(2, 0, KEY_T), - KEY(3, 0, KEY_HOME), - KEY(6, 0, KEY_I), - KEY(7, 0, KEY_LEFTSHIFT), - KEY(0, 1, KEY_D), - KEY(1, 1, KEY_F), - KEY(2, 1, KEY_G), - KEY(3, 1, KEY_SEND), - KEY(6, 1, KEY_K), - KEY(7, 1, KEY_ENTER), - KEY(0, 2, KEY_X), - KEY(1, 2, KEY_C), - KEY(2, 2, KEY_V), - KEY(3, 2, KEY_END), - KEY(6, 2, KEY_DOT), - KEY(7, 2, KEY_CAPSLOCK), - KEY(0, 3, KEY_Z), - KEY(1, 3, KEY_KPPLUS), - KEY(2, 3, KEY_B), - KEY(3, 3, KEY_F1), - KEY(6, 3, KEY_O), - KEY(7, 3, KEY_SPACE), - KEY(0, 4, KEY_W), - KEY(1, 4, KEY_Y), - KEY(2, 4, KEY_U), - KEY(3, 4, KEY_F2), - KEY(4, 4, KEY_VOLUMEUP), - KEY(6, 4, KEY_L), - KEY(7, 4, KEY_LEFT), - KEY(0, 5, KEY_S), - KEY(1, 5, KEY_H), - KEY(2, 5, KEY_J), - KEY(3, 5, KEY_F3), - KEY(5, 5, KEY_VOLUMEDOWN), - KEY(6, 5, KEY_M), - KEY(4, 5, KEY_ENTER), - KEY(7, 5, KEY_RIGHT), - KEY(0, 6, KEY_Q), - KEY(1, 6, KEY_A), - KEY(2, 6, KEY_N), - KEY(3, 6, KEY_BACKSPACE), - KEY(6, 6, KEY_P), - KEY(7, 6, KEY_UP), - KEY(6, 7, KEY_SELECT), - KEY(7, 7, KEY_DOWN), - KEY(0, 7, KEY_PROG1), /*MACRO 1 <User defined> */ - KEY(1, 7, KEY_PROG2), /*MACRO 2 <User defined> */ - KEY(2, 7, KEY_PROG3), /*MACRO 3 <User defined> */ - KEY(3, 7, KEY_PROG4), /*MACRO 4 <User defined> */ - 0 -}; - -static struct matrix_keymap_data board_map_data = { - .keymap = board_keymap, - .keymap_size = ARRAY_SIZE(board_keymap), -}; - -static struct twl4030_keypad_data zoom2_kp_twl4030_data = { - .keymap_data = &board_map_data, - .rows = 8, - .cols = 8, - .rep = 1, -}; - -static struct omap_board_config_kernel zoom2_config[] __initdata = { -}; - -static struct regulator_consumer_supply zoom2_vmmc1_supply = { - .supply = "vmmc", -}; - -static struct regulator_consumer_supply zoom2_vsim_supply = { - .supply = "vmmc_aux", -}; - -static struct regulator_consumer_supply zoom2_vmmc2_supply = { - .supply = "vmmc", -}; - -/* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */ -static struct regulator_init_data zoom2_vmmc1 = { - .constraints = { - .min_uV = 1850000, - .max_uV = 3150000, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE - | REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = 1, - .consumer_supplies = &zoom2_vmmc1_supply, -}; - -/* VMMC2 for MMC2 card */ -static struct regulator_init_data zoom2_vmmc2 = { - .constraints = { - .min_uV = 1850000, - .max_uV = 1850000, - .apply_uV = true, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = 1, - .consumer_supplies = &zoom2_vmmc2_supply, -}; - -/* VSIM for OMAP VDD_MMC1A (i/o for DAT4..DAT7) */ -static struct regulator_init_data zoom2_vsim = { - .constraints = { - .min_uV = 1800000, - .max_uV = 3000000, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE - | REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = 1, - .consumer_supplies = &zoom2_vsim_supply, -}; - -static struct twl4030_hsmmc_info mmc[] __initdata = { - { - .mmc = 1, - .wires = 4, - .gpio_wp = -EINVAL, - }, - { - .mmc = 2, - .wires = 4, - .gpio_wp = -EINVAL, - }, - {} /* Terminator */ -}; - -static int zoom2_twl_gpio_setup(struct device *dev, - unsigned gpio, unsigned ngpio) +static void __init omap_zoom2_map_io(void) { - /* gpio + 0 is "mmc0_cd" (input/IRQ), - * gpio + 1 is "mmc1_cd" (input/IRQ) - */ - mmc[0].gpio_cd = gpio + 0; - mmc[1].gpio_cd = gpio + 1; - twl4030_mmc_init(mmc); - - /* link regulators to MMC adapters ... we "know" the - * regulators will be set up only *after* we return. - */ - zoom2_vmmc1_supply.dev = mmc[0].dev; - zoom2_vsim_supply.dev = mmc[0].dev; - zoom2_vmmc2_supply.dev = mmc[1].dev; - - return 0; + omap2_set_globals_343x(); + omap2_map_common_io(); } - -static int zoom2_batt_table[] = { -/* 0 C*/ -30800, 29500, 28300, 27100, -26000, 24900, 23900, 22900, 22000, 21100, 20300, 19400, 18700, 17900, -17200, 16500, 15900, 15300, 14700, 14100, 13600, 13100, 12600, 12100, -11600, 11200, 10800, 10400, 10000, 9630, 9280, 8950, 8620, 8310, -8020, 7730, 7460, 7200, 6950, 6710, 6470, 6250, 6040, 5830, -5640, 5450, 5260, 5090, 4920, 4760, 4600, 4450, 4310, 4170, -4040, 3910, 3790, 3670, 3550 -}; - -static struct twl4030_bci_platform_data zoom2_bci_data = { - .battery_tmp_tbl = zoom2_batt_table, - .tblsize = ARRAY_SIZE(zoom2_batt_table), -}; - -static struct twl4030_usb_data zoom2_usb_data = { - .usb_mode = T2_USB_MODE_ULPI, +static struct omap_board_config_kernel zoom2_config[] __initdata = { }; - static void __init omap_zoom2_init_irq(void) { omap_board_config = zoom2_config; @@ -220,65 +39,13 @@ static void __init omap_zoom2_init_irq(void) omap_gpio_init(); } -static struct twl4030_gpio_platform_data zoom2_gpio_data = { - .gpio_base = OMAP_MAX_GPIO_LINES, - .irq_base = TWL4030_GPIO_IRQ_BASE, - .irq_end = TWL4030_GPIO_IRQ_END, - .setup = zoom2_twl_gpio_setup, -}; - -static struct twl4030_madc_platform_data zoom2_madc_data = { - .irq_line = 1, -}; - -static struct twl4030_platform_data zoom2_twldata = { - .irq_base = TWL4030_IRQ_BASE, - .irq_end = TWL4030_IRQ_END, - - /* platform_data for children goes here */ - .bci = &zoom2_bci_data, - .madc = &zoom2_madc_data, - .usb = &zoom2_usb_data, - .gpio = &zoom2_gpio_data, - .keypad = &zoom2_kp_twl4030_data, - .vmmc1 = &zoom2_vmmc1, - .vmmc2 = &zoom2_vmmc2, - .vsim = &zoom2_vsim, - -}; - -static struct i2c_board_info __initdata zoom2_i2c_boardinfo[] = { - { - I2C_BOARD_INFO("twl4030", 0x48), - .flags = I2C_CLIENT_WAKE, - .irq = INT_34XX_SYS_NIRQ, - .platform_data = &zoom2_twldata, - }, -}; - -static int __init omap_i2c_init(void) -{ - omap_register_i2c_bus(1, 2600, zoom2_i2c_boardinfo, - ARRAY_SIZE(zoom2_i2c_boardinfo)); - omap_register_i2c_bus(2, 400, NULL, 0); - omap_register_i2c_bus(3, 400, NULL, 0); - return 0; -} - extern int __init omap_zoom2_debugboard_init(void); +extern void __init zoom_peripherals_init(void); static void __init omap_zoom2_init(void) { - omap_i2c_init(); - omap_serial_init(); + zoom_peripherals_init(); omap_zoom2_debugboard_init(); - usb_musb_init(); -} - -static void __init omap_zoom2_map_io(void) -{ - omap2_set_globals_343x(); - omap2_map_common_io(); } MACHINE_START(OMAP_ZOOM2, "OMAP Zoom2 board") -- 1.6.5.1.69.g36942 ^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH v2 4/8] omap: zoom2: update defconfig for LL_DEBUG_NONE 2009-11-10 22:47 ` [PATCH v2 3/8] omap: zoom2: split board file for software reuse Vikram Pandita @ 2009-11-10 22:47 ` Vikram Pandita 2009-11-10 22:47 ` [PATCH v2 5/8] omap: zoom3: introduce zoom3 board support Vikram Pandita 2009-11-11 1:24 ` [PATCH v2 3/8] omap: zoom2: split board file for software reuse Tony Lindgren 1 sibling, 1 reply; 16+ messages in thread From: Vikram Pandita @ 2009-11-10 22:47 UTC (permalink / raw) To: linux-omap; +Cc: Vikram Pandita Update DEBUG_LL for zoom2 board as CONFIG_OMAP_LL_DEBUG_NONE Signed-off-by: Vikram Pandita <vikram.pandita@ti.com> --- arch/arm/configs/omap_zoom2_defconfig | 3 ++- 1 files changed, 2 insertions(+), 1 deletions(-) diff --git a/arch/arm/configs/omap_zoom2_defconfig b/arch/arm/configs/omap_zoom2_defconfig index f1739fa..2eec53b 100644 --- a/arch/arm/configs/omap_zoom2_defconfig +++ b/arch/arm/configs/omap_zoom2_defconfig @@ -202,7 +202,8 @@ CONFIG_OMAP_32K_TIMER_HZ=128 CONFIG_OMAP_DM_TIMER=y # CONFIG_OMAP_LL_DEBUG_UART1 is not set # CONFIG_OMAP_LL_DEBUG_UART2 is not set -CONFIG_OMAP_LL_DEBUG_UART3=y +# CONFIG_OMAP_LL_DEBUG_UART3 is not set +CONFIG_OMAP_LL_DEBUG_NONE=y CONFIG_ARCH_OMAP34XX=y CONFIG_ARCH_OMAP3430=y -- 1.6.5.1.69.g36942 ^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH v2 5/8] omap: zoom3: introduce zoom3 board support 2009-11-10 22:47 ` [PATCH v2 4/8] omap: zoom2: update defconfig for LL_DEBUG_NONE Vikram Pandita @ 2009-11-10 22:47 ` Vikram Pandita 2009-11-10 22:47 ` [PATCH v2 6/8] omap: zoom3: defconfig creation Vikram Pandita 0 siblings, 1 reply; 16+ messages in thread From: Vikram Pandita @ 2009-11-10 22:47 UTC (permalink / raw) To: linux-omap Cc: Vikram Pandita, Vikram Pandita, Chalhoub, Nicole, Bour, Vincent Zoom3 is the next versoin of Zoom2 board. There has been a silicon update from zoom2 to zoom3. Zoom2 has OMAP34xx Zoom3 has OMAP3630 [1] Zoom3 = OMAP3630 SOM board [2] + same zoom2 main board [3] + same debugboard Zoom3 has a SDRAM part from Hynix Zoom2 had SDRAM part from micron Hynix memory timings are contributed by: Chalhoub, Nicole and Bour, Vincent Reuse the zoom2 files as much for zoom3, as at board level, there is no change at all. References: (courtesy Nishant Menon) [1] OMAP3630 http://focus.ti.com/general/docs/wtbu/wtbuproductcontent.tsp?templateId=6123&navigationId=12836&contentId=52606 [2] SOM boards http://logicpd.com/products/system-modules/texas-instruments-omap35x-som-lv [3] Zoom2 boards http://logicpd.com/products/development-kits/texas-instruments-zoom%E2%84%A2-omap34x-ii-mdp OMAP3630: Signed-off-by: Vikram Pandita <vikram.pandtia@ti.com> Cc: Chalhoub, Nicole <n-chalhoub@ti.com> Cc: Bour, Vincent <v-bour@ti.com> --- arch/arm/mach-omap2/Kconfig | 4 + arch/arm/mach-omap2/Makefile | 4 + arch/arm/mach-omap2/board-zoom3.c | 60 ++++++++++++++++++++ arch/arm/mach-omap2/sdram-hynix-h8mbx00u0mer-0em.h | 51 +++++++++++++++++ 4 files changed, 119 insertions(+), 0 deletions(-) create mode 100644 arch/arm/mach-omap2/board-zoom3.c create mode 100644 arch/arm/mach-omap2/sdram-hynix-h8mbx00u0mer-0em.h diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig index 8685df5..9824775 100644 --- a/arch/arm/mach-omap2/Kconfig +++ b/arch/arm/mach-omap2/Kconfig @@ -101,6 +101,10 @@ config MACH_CM_T35 bool "CompuLab CM-T35 module" depends on ARCH_OMAP3 && ARCH_OMAP34XX +config MACH_OMAP_ZOOM3 + bool "OMAP3630 Zoom3 board" + depends on ARCH_OMAP3 && ARCH_OMAP34XX + config MACH_OMAP_4430SDP bool "OMAP 4430 SDP board" depends on ARCH_OMAP4 diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index 4d66b42..712e7fc 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -75,6 +75,10 @@ obj-$(CONFIG_MACH_OMAP_ZOOM2) += board-zoom2.o \ board-zoom-peripherals.o \ mmc-twl4030.o \ board-zoom-debugboard.o +obj-$(CONFIG_MACH_OMAP_ZOOM3) += board-zoom3.o \ + board-zoom-peripherals.o \ + mmc-twl4030.o \ + board-zoom-debugboard.o obj-$(CONFIG_MACH_CM_T35) += board-cm-t35.o \ mmc-twl4030.o diff --git a/arch/arm/mach-omap2/board-zoom3.c b/arch/arm/mach-omap2/board-zoom3.c new file mode 100644 index 0000000..b031eaa --- /dev/null +++ b/arch/arm/mach-omap2/board-zoom3.c @@ -0,0 +1,60 @@ +/* + * Copyright (C) 2009 Texas Instruments Inc. + * + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/input.h> +#include <linux/gpio.h> + +#include <asm/mach-types.h> +#include <asm/mach/arch.h> + +#include <plat/common.h> +#include <plat/board.h> + +#include "sdram-hynix-h8mbx00u0mer-0em.h" + +static void __init omap_zoom_map_io(void) +{ + omap2_set_globals_343x(); + omap2_map_common_io(); +} + +static struct omap_board_config_kernel zoom_config[] __initdata = { +}; + +static void __init omap_zoom_init_irq(void) +{ + omap_board_config = zoom_config; + omap_board_config_size = ARRAY_SIZE(zoom_config); + omap2_init_common_hw(h8mbx00u0mer0em_sdrc_params, + h8mbx00u0mer0em_sdrc_params); + omap_init_irq(); + omap_gpio_init(); +} + +extern int __init omap_zoom2_debugboard_init(void); +extern void __init zoom_peripherals_init(void); + +static void __init omap_zoom_init(void) +{ + zoom_peripherals_init(); + omap_zoom2_debugboard_init(); +} + +MACHINE_START(OMAP_ZOOM3, "OMAP Zoom3 board") + .phys_io = 0x48000000, + .io_pg_offst = ((0xfa000000) >> 18) & 0xfffc, + .boot_params = 0x80000100, + .map_io = omap_zoom_map_io, + .init_irq = omap_zoom_init_irq, + .init_machine = omap_zoom_init, + .timer = &omap_timer, +MACHINE_END diff --git a/arch/arm/mach-omap2/sdram-hynix-h8mbx00u0mer-0em.h b/arch/arm/mach-omap2/sdram-hynix-h8mbx00u0mer-0em.h new file mode 100644 index 0000000..8bfaf34 --- /dev/null +++ b/arch/arm/mach-omap2/sdram-hynix-h8mbx00u0mer-0em.h @@ -0,0 +1,51 @@ +/* + * SDRC register values for the Hynix H8MBX00U0MER-0EM + * + * Copyright (C) 2009 Texas Instruments, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __ARCH_ARM_MACH_OMAP2_SDRAM_HYNIX_H8MBX00U0MER0EM +#define __ARCH_ARM_MACH_OMAP2_SDRAM_HYNIX_H8MBX00U0MER0EM + +#include <plat/sdrc.h> + +/* Hynix H8MBX00U0MER-0EM */ +static struct omap_sdrc_params h8mbx00u0mer0em_sdrc_params[] = { + [0] = { + .rate = 200000000, + .actim_ctrla = 0xa2e1b4c6, + .actim_ctrlb = 0x0002131c, + .rfr_ctrl = 0x0005e601, + .mr = 0x00000032, + }, + [1] = { + .rate = 166000000, + .actim_ctrla = 0x629db4c6, + .actim_ctrlb = 0x00012214, + .rfr_ctrl = 0x0004dc01, + .mr = 0x00000032, + }, + [2] = { + .rate = 100000000, + .actim_ctrla = 0x51912284, + .actim_ctrlb = 0x0002120e, + .rfr_ctrl = 0x0002d101, + .mr = 0x00000022, + }, + [3] = { + .rate = 83000000, + .actim_ctrla = 0x31512283, + .actim_ctrlb = 0x0001220a, + .rfr_ctrl = 0x00025501, + .mr = 0x00000022, + }, + [4] = { + .rate = 0 + }, +}; + +#endif -- 1.6.5.1.69.g36942 ^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH v2 6/8] omap: zoom3: defconfig creation 2009-11-10 22:47 ` [PATCH v2 5/8] omap: zoom3: introduce zoom3 board support Vikram Pandita @ 2009-11-10 22:47 ` Vikram Pandita 2009-11-10 22:47 ` [PATCH v2 7/8] omap: 3630sdp: introduce 3630 sdp board support Vikram Pandita 0 siblings, 1 reply; 16+ messages in thread From: Vikram Pandita @ 2009-11-10 22:47 UTC (permalink / raw) To: linux-omap; +Cc: Vikram Pandita Create zoom3 defconfig file Signed-off-by: Vikram Pandita <vikram.pandita@ti.com> --- arch/arm/configs/omap_zoom3_defconfig | 1605 +++++++++++++++++++++++++++++++++ 1 files changed, 1605 insertions(+), 0 deletions(-) create mode 100644 arch/arm/configs/omap_zoom3_defconfig diff --git a/arch/arm/configs/omap_zoom3_defconfig b/arch/arm/configs/omap_zoom3_defconfig new file mode 100644 index 0000000..989cedd --- /dev/null +++ b/arch/arm/configs/omap_zoom3_defconfig @@ -0,0 +1,1605 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.32-rc5 +# Tue Nov 3 09:50:40 2009 +# +CONFIG_ARM=y +CONFIG_SYS_SUPPORTS_APM_EMULATION=y +CONFIG_GENERIC_GPIO=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_HARDIRQS=y +CONFIG_STACKTRACE_SUPPORT=y +CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_LOCKDEP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_ARCH_HAS_CPUFREQ=y +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y +CONFIG_VECTORS_BASE=0xffff0000 +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y + +# +# General setup +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +CONFIG_SWAP=y +CONFIG_SYSVIPC=y +CONFIG_SYSVIPC_SYSCTL=y +# CONFIG_POSIX_MQUEUE is not set +CONFIG_BSD_PROCESS_ACCT=y +# CONFIG_BSD_PROCESS_ACCT_V3 is not set +# CONFIG_TASKSTATS is not set +# CONFIG_AUDIT is not set + +# +# RCU Subsystem +# +CONFIG_TREE_RCU=y +# CONFIG_TREE_PREEMPT_RCU is not set +# CONFIG_RCU_TRACE is not set +CONFIG_RCU_FANOUT=32 +# CONFIG_RCU_FANOUT_EXACT is not set +# CONFIG_TREE_RCU_TRACE is not set +# CONFIG_IKCONFIG is not set +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_GROUP_SCHED=y +CONFIG_FAIR_GROUP_SCHED=y +# CONFIG_RT_GROUP_SCHED is not set +CONFIG_USER_SCHED=y +# CONFIG_CGROUP_SCHED is not set +# CONFIG_CGROUPS is not set +CONFIG_SYSFS_DEPRECATED=y +CONFIG_SYSFS_DEPRECATED_V2=y +# CONFIG_RELAY is not set +# CONFIG_NAMESPACES is not set +CONFIG_BLK_DEV_INITRD=y +CONFIG_INITRAMFS_SOURCE="" +CONFIG_RD_GZIP=y +# CONFIG_RD_BZIP2 is not set +# CONFIG_RD_LZMA is not set +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +CONFIG_SYSCTL=y +CONFIG_ANON_INODES=y +CONFIG_EMBEDDED=y +CONFIG_UID16=y +# CONFIG_SYSCTL_SYSCALL is not set +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +CONFIG_KALLSYMS_EXTRA_PASS=y +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_TIMERFD=y +CONFIG_EVENTFD=y +CONFIG_SHMEM=y +CONFIG_AIO=y + +# +# Kernel Performance Events And Counters +# +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_COMPAT_BRK=y +CONFIG_SLAB=y +# CONFIG_SLUB is not set +# CONFIG_SLOB is not set +# CONFIG_PROFILING is not set +CONFIG_HAVE_OPROFILE=y +# CONFIG_KPROBES is not set +CONFIG_HAVE_KPROBES=y +CONFIG_HAVE_KRETPROBES=y +CONFIG_HAVE_CLK=y + +# +# GCOV-based kernel profiling +# +# CONFIG_SLOW_WORK is not set +CONFIG_HAVE_GENERIC_DMA_COHERENT=y +CONFIG_SLABINFO=y +CONFIG_RT_MUTEXES=y +CONFIG_BASE_SMALL=0 +CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +CONFIG_MODVERSIONS=y +CONFIG_MODULE_SRCVERSION_ALL=y +CONFIG_BLOCK=y +CONFIG_LBDAF=y +# CONFIG_BLK_DEV_BSG is not set +# CONFIG_BLK_DEV_INTEGRITY is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" +CONFIG_FREEZER=y + +# +# System Type +# +CONFIG_MMU=y +# CONFIG_ARCH_AAEC2000 is not set +# CONFIG_ARCH_INTEGRATOR is not set +# CONFIG_ARCH_REALVIEW is not set +# CONFIG_ARCH_VERSATILE is not set +# CONFIG_ARCH_AT91 is not set +# CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_GEMINI is not set +# CONFIG_ARCH_EBSA110 is not set +# CONFIG_ARCH_EP93XX is not set +# CONFIG_ARCH_FOOTBRIDGE is not set +# CONFIG_ARCH_MXC is not set +# CONFIG_ARCH_STMP3XXX is not set +# CONFIG_ARCH_NETX is not set +# CONFIG_ARCH_H720X is not set +# CONFIG_ARCH_NOMADIK is not set +# CONFIG_ARCH_IOP13XX is not set +# CONFIG_ARCH_IOP32X is not set +# CONFIG_ARCH_IOP33X is not set +# CONFIG_ARCH_IXP23XX is not set +# CONFIG_ARCH_IXP2000 is not set +# CONFIG_ARCH_IXP4XX is not set +# CONFIG_ARCH_L7200 is not set +# CONFIG_ARCH_KIRKWOOD is not set +# CONFIG_ARCH_LOKI is not set +# CONFIG_ARCH_MV78XX0 is not set +# CONFIG_ARCH_ORION5X is not set +# CONFIG_ARCH_MMP is not set +# CONFIG_ARCH_KS8695 is not set +# CONFIG_ARCH_NS9XXX is not set +# CONFIG_ARCH_W90X900 is not set +# CONFIG_ARCH_PNX4008 is not set +# CONFIG_ARCH_PXA is not set +# CONFIG_ARCH_MSM is not set +# CONFIG_ARCH_RPC is not set +# CONFIG_ARCH_SA1100 is not set +# CONFIG_ARCH_S3C2410 is not set +# CONFIG_ARCH_S3C64XX is not set +# CONFIG_ARCH_S5PC1XX is not set +# CONFIG_ARCH_SHARK is not set +# CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_U300 is not set +# CONFIG_ARCH_DAVINCI is not set +CONFIG_ARCH_OMAP=y +# CONFIG_ARCH_BCMRING is not set + +# +# TI OMAP Implementations +# +CONFIG_ARCH_OMAP_OTG=y +# CONFIG_ARCH_OMAP1 is not set +# CONFIG_ARCH_OMAP2 is not set +CONFIG_ARCH_OMAP3=y +# CONFIG_ARCH_OMAP4 is not set + +# +# OMAP Feature Selections +# +# CONFIG_OMAP_DEBUG_POWERDOMAIN is not set +# CONFIG_OMAP_DEBUG_CLOCKDOMAIN is not set +# CONFIG_OMAP_RESET_CLOCKS is not set +CONFIG_OMAP_MUX=y +CONFIG_OMAP_MUX_DEBUG=y +CONFIG_OMAP_MUX_WARNINGS=y +CONFIG_OMAP_MCBSP=y +# CONFIG_OMAP_MBOX_FWK is not set +# CONFIG_OMAP_MPU_TIMER is not set +CONFIG_OMAP_32K_TIMER=y +CONFIG_OMAP_32K_TIMER_HZ=128 +CONFIG_OMAP_DM_TIMER=y +# CONFIG_OMAP_LL_DEBUG_UART1 is not set +# CONFIG_OMAP_LL_DEBUG_UART2 is not set +# CONFIG_OMAP_LL_DEBUG_UART3 is not set +CONFIG_OMAP_LL_DEBUG_NONE=y +# CONFIG_OMAP_PM_NONE is not set +CONFIG_OMAP_PM_NOOP=y +CONFIG_ARCH_OMAP34XX=y +CONFIG_ARCH_OMAP3430=y + +# +# OMAP Board Type +# +# CONFIG_MACH_OMAP3_BEAGLE is not set +# CONFIG_MACH_OMAP_LDP is not set +# CONFIG_MACH_OVERO is not set +# CONFIG_MACH_OMAP3EVM is not set +# CONFIG_MACH_OMAP3_PANDORA is not set +# CONFIG_MACH_OMAP_3430SDP is not set +# CONFIG_MACH_NOKIA_RX51 is not set +# CONFIG_MACH_OMAP_ZOOM2 is not set +# CONFIG_MACH_CM_T35 is not set +CONFIG_MACH_OMAP_ZOOM3=y + +# +# Processor Type +# +CONFIG_CPU_32=y +CONFIG_CPU_32v6K=y +CONFIG_CPU_V7=y +CONFIG_CPU_32v7=y +CONFIG_CPU_ABRT_EV7=y +CONFIG_CPU_PABRT_V7=y +CONFIG_CPU_CACHE_V7=y +CONFIG_CPU_CACHE_VIPT=y +CONFIG_CPU_COPY_V6=y +CONFIG_CPU_TLB_V7=y +CONFIG_CPU_HAS_ASID=y +CONFIG_CPU_CP15=y +CONFIG_CPU_CP15_MMU=y + +# +# Processor Features +# +CONFIG_ARM_THUMB=y +# CONFIG_ARM_THUMBEE is not set +# CONFIG_CPU_ICACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_DISABLE is not set +# CONFIG_CPU_BPREDICT_DISABLE is not set +CONFIG_HAS_TLS_REG=y +CONFIG_ARM_L1_CACHE_SHIFT=6 +# CONFIG_ARM_ERRATA_430973 is not set +# CONFIG_ARM_ERRATA_458693 is not set +# CONFIG_ARM_ERRATA_460075 is not set +CONFIG_COMMON_CLKDEV=y + +# +# Bus support +# +# CONFIG_PCI_SYSCALL is not set +# CONFIG_ARCH_SUPPORTS_MSI is not set +# CONFIG_PCCARD is not set + +# +# Kernel Features +# +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +CONFIG_VMSPLIT_3G=y +# CONFIG_VMSPLIT_2G is not set +# CONFIG_VMSPLIT_1G is not set +CONFIG_PAGE_OFFSET=0xC0000000 +CONFIG_PREEMPT_NONE=y +# CONFIG_PREEMPT_VOLUNTARY is not set +# CONFIG_PREEMPT is not set +CONFIG_HZ=128 +# CONFIG_THUMB2_KERNEL is not set +CONFIG_AEABI=y +CONFIG_OABI_COMPAT=y +# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set +# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set +# CONFIG_HIGHMEM is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +CONFIG_PAGEFLAGS_EXTENDED=y +CONFIG_SPLIT_PTLOCK_CPUS=4 +# CONFIG_PHYS_ADDR_T_64BIT is not set +CONFIG_ZONE_DMA_FLAG=0 +CONFIG_VIRT_TO_BUS=y +CONFIG_HAVE_MLOCK=y +CONFIG_HAVE_MLOCKED_PAGE_BIT=y +# CONFIG_KSM is not set +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 +# CONFIG_LEDS is not set +CONFIG_ALIGNMENT_TRAP=y +# CONFIG_UACCESS_WITH_MEMCPY is not set + +# +# Boot options +# +CONFIG_ZBOOT_ROM_TEXT=0x0 +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_CMDLINE="root=/dev/nfs nfsroot=192.168.0.1:/home/user/buildroot ip=192.168.0.2:192.168.0.1:192.168.0.1:255.255.255.0:tgt:eth0:off rw console=ttyS2,115200n8" +# CONFIG_XIP_KERNEL is not set +# CONFIG_KEXEC is not set + +# +# CPU Power Management +# +# CONFIG_CPU_FREQ is not set +# CONFIG_CPU_IDLE is not set + +# +# Floating point emulation +# + +# +# At least one emulation must be selected +# +CONFIG_FPE_NWFPE=y +# CONFIG_FPE_NWFPE_XP is not set +# CONFIG_FPE_FASTFPE is not set +CONFIG_VFP=y +CONFIG_VFPv3=y +# CONFIG_NEON is not set + +# +# Userspace binary formats +# +CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +CONFIG_HAVE_AOUT=y +# CONFIG_BINFMT_AOUT is not set +CONFIG_BINFMT_MISC=y + +# +# Power management options +# +CONFIG_PM=y +CONFIG_PM_DEBUG=y +CONFIG_PM_VERBOSE=y +CONFIG_CAN_PM_TRACE=y +CONFIG_PM_SLEEP=y +CONFIG_SUSPEND=y +# CONFIG_PM_TEST_SUSPEND is not set +CONFIG_SUSPEND_FREEZER=y +# CONFIG_APM_EMULATION is not set +# CONFIG_PM_RUNTIME is not set +CONFIG_ARCH_SUSPEND_POSSIBLE=y +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +CONFIG_XFRM=y +CONFIG_XFRM_USER=y +# CONFIG_XFRM_SUB_POLICY is not set +CONFIG_XFRM_MIGRATE=y +# CONFIG_XFRM_STATISTICS is not set +CONFIG_NET_KEY=y +CONFIG_NET_KEY_MIGRATE=y +CONFIG_INET=y +CONFIG_IP_MULTICAST=y +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +CONFIG_IP_PNP_RARP=y +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_IP_MROUTE is not set +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set +CONFIG_INET_XFRM_MODE_TRANSPORT=y +CONFIG_INET_XFRM_MODE_TUNNEL=y +CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +# CONFIG_IPV6 is not set +# CONFIG_NETWORK_SECMARK is not set +# CONFIG_NETFILTER is not set +# CONFIG_IP_DCCP is not set +# CONFIG_IP_SCTP is not set +# CONFIG_RDS is not set +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set +# CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set +# CONFIG_NET_SCHED is not set +# CONFIG_DCB is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_CAN is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_AF_RXRPC is not set +# CONFIG_WIRELESS is not set +# CONFIG_WIMAX is not set +# CONFIG_RFKILL is not set +# CONFIG_NET_9P is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +# CONFIG_DEVTMPFS is not set +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_FW_LOADER is not set +# CONFIG_DEBUG_DRIVER is not set +# CONFIG_DEBUG_DEVRES is not set +# CONFIG_SYS_HYPERVISOR is not set +CONFIG_CONNECTOR=y +CONFIG_PROC_EVENTS=y +# CONFIG_MTD is not set +# CONFIG_PARPORT is not set +CONFIG_BLK_DEV=y +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=y +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +# CONFIG_BLK_DEV_NBD is not set +# CONFIG_BLK_DEV_UB is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=16384 +# CONFIG_BLK_DEV_XIP is not set +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set +# CONFIG_MG_DISK is not set +CONFIG_MISC_DEVICES=y +# CONFIG_ICS932S401 is not set +# CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_ISL29003 is not set +# CONFIG_C2PORT is not set + +# +# EEPROM support +# +# CONFIG_EEPROM_AT24 is not set +# CONFIG_EEPROM_AT25 is not set +# CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set +# CONFIG_EEPROM_93CX6 is not set +CONFIG_HAVE_IDE=y +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +CONFIG_SCSI=y +CONFIG_SCSI_DMA=y +# CONFIG_SCSI_TGT is not set +# CONFIG_SCSI_NETLINK is not set +CONFIG_SCSI_PROC_FS=y + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=y +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set +# CONFIG_BLK_DEV_SR is not set +# CONFIG_CHR_DEV_SG is not set +# CONFIG_CHR_DEV_SCH is not set +# CONFIG_SCSI_MULTI_LUN is not set +# CONFIG_SCSI_CONSTANTS is not set +# CONFIG_SCSI_LOGGING is not set +# CONFIG_SCSI_SCAN_ASYNC is not set +CONFIG_SCSI_WAIT_SCAN=m + +# +# SCSI Transports +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set +CONFIG_SCSI_LOWLEVEL=y +# CONFIG_ISCSI_TCP is not set +# CONFIG_LIBFC is not set +# CONFIG_LIBFCOE is not set +# CONFIG_SCSI_DEBUG is not set +# CONFIG_SCSI_DH is not set +# CONFIG_SCSI_OSD_INITIATOR is not set +# CONFIG_ATA is not set +# CONFIG_MD is not set +CONFIG_NETDEVICES=y +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_MACVLAN is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set +# CONFIG_VETH is not set +CONFIG_PHYLIB=y + +# +# MII PHY device drivers +# +# CONFIG_MARVELL_PHY is not set +# CONFIG_DAVICOM_PHY is not set +# CONFIG_QSEMI_PHY is not set +# CONFIG_LXT_PHY is not set +# CONFIG_CICADA_PHY is not set +# CONFIG_VITESSE_PHY is not set +CONFIG_SMSC_PHY=y +# CONFIG_BROADCOM_PHY is not set +# CONFIG_ICPLUS_PHY is not set +# CONFIG_REALTEK_PHY is not set +# CONFIG_NATIONAL_PHY is not set +# CONFIG_STE10XP is not set +# CONFIG_LSI_ET1011C_PHY is not set +# CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +# CONFIG_AX88796 is not set +# CONFIG_SMC91X is not set +# CONFIG_DM9000 is not set +# CONFIG_ENC28J60 is not set +# CONFIG_ETHOC is not set +# CONFIG_SMC911X is not set +CONFIG_SMSC911X=y +# CONFIG_DNET is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set +# CONFIG_B44 is not set +# CONFIG_KS8842 is not set +# CONFIG_KS8851 is not set +# CONFIG_KS8851_MLL is not set +CONFIG_NETDEV_1000=y +CONFIG_NETDEV_10000=y +CONFIG_WLAN=y +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set + +# +# Enable WiMAX (Networking options) to see the WiMAX drivers +# + +# +# USB Network Adapters +# +# CONFIG_USB_CATC is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_RTL8150 is not set +# CONFIG_USB_USBNET is not set +# CONFIG_WAN is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set +# CONFIG_ISDN is not set +# CONFIG_PHONE is not set + +# +# Input device support +# +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set +# CONFIG_INPUT_POLLDEV is not set + +# +# Userland interfaces +# +# CONFIG_INPUT_MOUSEDEV is not set +# CONFIG_INPUT_JOYDEV is not set +CONFIG_INPUT_EVDEV=y +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TABLET is not set +CONFIG_INPUT_TOUCHSCREEN=y +CONFIG_TOUCHSCREEN_ADS7846=y +# CONFIG_TOUCHSCREEN_AD7877 is not set +# CONFIG_TOUCHSCREEN_AD7879_I2C is not set +# CONFIG_TOUCHSCREEN_AD7879_SPI is not set +# CONFIG_TOUCHSCREEN_AD7879 is not set +# CONFIG_TOUCHSCREEN_EETI is not set +# CONFIG_TOUCHSCREEN_FUJITSU is not set +# CONFIG_TOUCHSCREEN_GUNZE is not set +# CONFIG_TOUCHSCREEN_ELO is not set +# CONFIG_TOUCHSCREEN_WACOM_W8001 is not set +# CONFIG_TOUCHSCREEN_MCS5000 is not set +# CONFIG_TOUCHSCREEN_MTOUCH is not set +# CONFIG_TOUCHSCREEN_INEXIO is not set +# CONFIG_TOUCHSCREEN_MK712 is not set +# CONFIG_TOUCHSCREEN_PENMOUNT is not set +# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set +# CONFIG_TOUCHSCREEN_TOUCHWIN is not set +# CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set +# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set +# CONFIG_TOUCHSCREEN_TSC2007 is not set +# CONFIG_TOUCHSCREEN_W90X900 is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_CONSOLE_TRANSLATIONS=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_VT_HW_CONSOLE_BINDING is not set +CONFIG_DEVKMEM=y +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_NR_UARTS=32 +CONFIG_SERIAL_8250_RUNTIME_UARTS=4 +CONFIG_SERIAL_8250_EXTENDED=y +CONFIG_SERIAL_8250_MANY_PORTS=y +CONFIG_SERIAL_8250_SHARE_IRQ=y +CONFIG_SERIAL_8250_DETECT_IRQ=y +CONFIG_SERIAL_8250_RSA=y + +# +# Non-8250 serial port support +# +# CONFIG_SERIAL_MAX3100 is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_UNIX98_PTYS=y +# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set +# CONFIG_LEGACY_PTYS is not set +# CONFIG_IPMI_HANDLER is not set +CONFIG_HW_RANDOM=y +# CONFIG_HW_RANDOM_TIMERIOMEM is not set +# CONFIG_R3964 is not set +# CONFIG_RAW_DRIVER is not set +# CONFIG_TCG_TPM is not set +CONFIG_I2C=y +CONFIG_I2C_BOARDINFO=y +CONFIG_I2C_COMPAT=y +CONFIG_I2C_CHARDEV=y +CONFIG_I2C_HELPER_AUTO=y + +# +# I2C Hardware Bus support +# + +# +# I2C system bus drivers (mostly embedded / system-on-chip) +# +# CONFIG_I2C_DESIGNWARE is not set +# CONFIG_I2C_GPIO is not set +# CONFIG_I2C_OCORES is not set +CONFIG_I2C_OMAP=y +# CONFIG_I2C_SIMTEC is not set + +# +# External I2C/SMBus adapter drivers +# +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_TAOS_EVM is not set +# CONFIG_I2C_TINY_USB is not set + +# +# Other I2C/SMBus bus drivers +# +# CONFIG_I2C_PCA_PLATFORM is not set +# CONFIG_I2C_STUB is not set + +# +# Miscellaneous I2C Chip support +# +# CONFIG_DS1682 is not set +# CONFIG_SENSORS_TSL2550 is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set +CONFIG_SPI=y +# CONFIG_SPI_DEBUG is not set +CONFIG_SPI_MASTER=y + +# +# SPI Master Controller Drivers +# +# CONFIG_SPI_BITBANG is not set +# CONFIG_SPI_GPIO is not set +CONFIG_SPI_OMAP24XX=y + +# +# SPI Protocol Masters +# +# CONFIG_SPI_SPIDEV is not set +# CONFIG_SPI_TLE62X0 is not set + +# +# PPS support +# +# CONFIG_PPS is not set +CONFIG_ARCH_REQUIRE_GPIOLIB=y +CONFIG_GPIOLIB=y +# CONFIG_DEBUG_GPIO is not set +# CONFIG_GPIO_SYSFS is not set + +# +# Memory mapped GPIO expanders: +# + +# +# I2C GPIO expanders: +# +# CONFIG_GPIO_MAX732X is not set +# CONFIG_GPIO_PCA953X is not set +# CONFIG_GPIO_PCF857X is not set +CONFIG_GPIO_TWL4030=y + +# +# PCI GPIO expanders: +# + +# +# SPI GPIO expanders: +# +# CONFIG_GPIO_MAX7301 is not set +# CONFIG_GPIO_MCP23S08 is not set +# CONFIG_GPIO_MC33880 is not set + +# +# AC97 GPIO expanders: +# +CONFIG_W1=y +CONFIG_W1_CON=y + +# +# 1-wire Bus Masters +# +# CONFIG_W1_MASTER_DS2490 is not set +# CONFIG_W1_MASTER_DS2482 is not set +# CONFIG_W1_MASTER_DS1WM is not set +# CONFIG_W1_MASTER_GPIO is not set +# CONFIG_HDQ_MASTER_OMAP is not set + +# +# 1-wire Slaves +# +# CONFIG_W1_SLAVE_THERM is not set +# CONFIG_W1_SLAVE_SMEM is not set +# CONFIG_W1_SLAVE_DS2431 is not set +# CONFIG_W1_SLAVE_DS2433 is not set +# CONFIG_W1_SLAVE_DS2760 is not set +# CONFIG_W1_SLAVE_BQ27000 is not set +CONFIG_POWER_SUPPLY=y +# CONFIG_POWER_SUPPLY_DEBUG is not set +# CONFIG_PDA_POWER is not set +# CONFIG_BATTERY_DS2760 is not set +# CONFIG_BATTERY_DS2782 is not set +# CONFIG_BATTERY_BQ27x00 is not set +# CONFIG_BATTERY_MAX17040 is not set +# CONFIG_HWMON is not set +# CONFIG_THERMAL is not set +CONFIG_WATCHDOG=y +CONFIG_WATCHDOG_NOWAYOUT=y + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set +# CONFIG_OMAP_WATCHDOG is not set +# CONFIG_TWL4030_WATCHDOG is not set + +# +# USB-based Watchdog Cards +# +# CONFIG_USBPCWATCHDOG is not set +CONFIG_SSB_POSSIBLE=y + +# +# Sonics Silicon Backplane +# +# CONFIG_SSB is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_CORE is not set +# CONFIG_MFD_SM501 is not set +# CONFIG_MFD_ASIC3 is not set +# CONFIG_HTC_EGPIO is not set +# CONFIG_HTC_PASIC3 is not set +# CONFIG_TPS65010 is not set +CONFIG_TWL4030_CORE=y +# CONFIG_TWL4030_POWER is not set +# CONFIG_MFD_TMIO is not set +# CONFIG_MFD_T7L66XB is not set +# CONFIG_MFD_TC6387XB is not set +# CONFIG_MFD_TC6393XB is not set +# CONFIG_PMIC_DA903X is not set +# CONFIG_MFD_WM8400 is not set +# CONFIG_MFD_WM831X is not set +# CONFIG_MFD_WM8350_I2C is not set +# CONFIG_MFD_PCF50633 is not set +# CONFIG_MFD_MC13783 is not set +# CONFIG_AB3100_CORE is not set +# CONFIG_EZX_PCAP is not set +CONFIG_REGULATOR=y +# CONFIG_REGULATOR_DEBUG is not set +# CONFIG_REGULATOR_FIXED_VOLTAGE is not set +# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set +# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set +# CONFIG_REGULATOR_BQ24022 is not set +# CONFIG_REGULATOR_MAX1586 is not set +CONFIG_REGULATOR_TWL4030=y +# CONFIG_REGULATOR_LP3971 is not set +# CONFIG_REGULATOR_TPS65023 is not set +# CONFIG_REGULATOR_TPS6507X is not set +# CONFIG_MEDIA_SUPPORT is not set + +# +# Graphics support +# +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=m +# CONFIG_FB is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set + +# +# Console display driver support +# +# CONFIG_VGA_CONSOLE is not set +CONFIG_DUMMY_CONSOLE=y +CONFIG_SOUND=y +# CONFIG_SOUND_OSS_CORE is not set +CONFIG_SND=y +# CONFIG_SND_SEQUENCER is not set +# CONFIG_SND_MIXER_OSS is not set +# CONFIG_SND_PCM_OSS is not set +# CONFIG_SND_HRTIMER is not set +# CONFIG_SND_DYNAMIC_MINORS is not set +CONFIG_SND_SUPPORT_OLD_API=y +CONFIG_SND_VERBOSE_PROCFS=y +# CONFIG_SND_VERBOSE_PRINTK is not set +# CONFIG_SND_DEBUG is not set +# CONFIG_SND_RAWMIDI_SEQ is not set +# CONFIG_SND_OPL3_LIB_SEQ is not set +# CONFIG_SND_OPL4_LIB_SEQ is not set +# CONFIG_SND_SBAWE_SEQ is not set +# CONFIG_SND_EMU10K1_SEQ is not set +CONFIG_SND_DRIVERS=y +# CONFIG_SND_DUMMY is not set +# CONFIG_SND_MTPAV is not set +# CONFIG_SND_SERIAL_U16550 is not set +# CONFIG_SND_MPU401 is not set +CONFIG_SND_ARM=y +CONFIG_SND_SPI=y +CONFIG_SND_USB=y +# CONFIG_SND_USB_AUDIO is not set +# CONFIG_SND_USB_CAIAQ is not set +# CONFIG_SND_SOC is not set +# CONFIG_SOUND_PRIME is not set +CONFIG_HID_SUPPORT=y +CONFIG_HID=y +# CONFIG_HIDRAW is not set + +# +# USB Input Devices +# +CONFIG_USB_HID=y +# CONFIG_HID_PID is not set +# CONFIG_USB_HIDDEV is not set + +# +# Special HID drivers +# +# CONFIG_HID_A4TECH is not set +# CONFIG_HID_APPLE is not set +# CONFIG_HID_BELKIN is not set +# CONFIG_HID_CHERRY is not set +# CONFIG_HID_CHICONY is not set +# CONFIG_HID_CYPRESS is not set +# CONFIG_HID_DRAGONRISE is not set +# CONFIG_HID_EZKEY is not set +# CONFIG_HID_KYE is not set +# CONFIG_HID_GYRATION is not set +# CONFIG_HID_TWINHAN is not set +# CONFIG_HID_KENSINGTON is not set +# CONFIG_HID_LOGITECH is not set +# CONFIG_HID_MICROSOFT is not set +# CONFIG_HID_MONTEREY is not set +# CONFIG_HID_NTRIG is not set +# CONFIG_HID_PANTHERLORD is not set +# CONFIG_HID_PETALYNX is not set +# CONFIG_HID_SAMSUNG is not set +# CONFIG_HID_SONY is not set +# CONFIG_HID_SUNPLUS is not set +# CONFIG_HID_GREENASIA is not set +# CONFIG_HID_SMARTJOYPLUS is not set +# CONFIG_HID_TOPSEED is not set +# CONFIG_HID_THRUSTMASTER is not set +# CONFIG_HID_ZEROPLUS is not set +CONFIG_USB_SUPPORT=y +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y +CONFIG_USB=y +CONFIG_USB_DEBUG=y +CONFIG_USB_ANNOUNCE_NEW_DEVICES=y + +# +# Miscellaneous USB options +# +# CONFIG_USB_DEVICEFS is not set +CONFIG_USB_DEVICE_CLASS=y +# CONFIG_USB_DYNAMIC_MINORS is not set +CONFIG_USB_SUSPEND=y +CONFIG_USB_OTG=y +# CONFIG_USB_OTG_WHITELIST is not set +# CONFIG_USB_OTG_BLACKLIST_HUB is not set +CONFIG_USB_MON=y +# CONFIG_USB_WUSB is not set +# CONFIG_USB_WUSB_CBAF is not set + +# +# USB Host Controller Drivers +# +# CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_EHCI_HCD is not set +# CONFIG_USB_OXU210HP_HCD is not set +# CONFIG_USB_ISP116X_HCD is not set +# CONFIG_USB_ISP1760_HCD is not set +# CONFIG_USB_ISP1362_HCD is not set +# CONFIG_USB_OHCI_HCD is not set +# CONFIG_USB_SL811_HCD is not set +# CONFIG_USB_R8A66597_HCD is not set +# CONFIG_USB_HWA_HCD is not set +CONFIG_USB_MUSB_HDRC=y +CONFIG_USB_MUSB_SOC=y + +# +# OMAP 343x high speed USB support +# +# CONFIG_USB_MUSB_HOST is not set +# CONFIG_USB_MUSB_PERIPHERAL is not set +CONFIG_USB_MUSB_OTG=y +CONFIG_USB_GADGET_MUSB_HDRC=y +CONFIG_USB_MUSB_HDRC_HCD=y +# CONFIG_MUSB_PIO_ONLY is not set +CONFIG_USB_INVENTRA_DMA=y +# CONFIG_USB_TI_CPPI_DMA is not set +CONFIG_USB_MUSB_DEBUG=y + +# +# USB Device Class drivers +# +# CONFIG_USB_ACM is not set +# CONFIG_USB_PRINTER is not set +# CONFIG_USB_WDM is not set +# CONFIG_USB_TMC is not set + +# +# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may +# + +# +# also be needed; see USB_STORAGE Help for more info +# +CONFIG_USB_STORAGE=y +CONFIG_USB_STORAGE_DEBUG=y +# CONFIG_USB_STORAGE_DATAFAB is not set +# CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_ISD200 is not set +# CONFIG_USB_STORAGE_USBAT is not set +# CONFIG_USB_STORAGE_SDDR09 is not set +# CONFIG_USB_STORAGE_SDDR55 is not set +# CONFIG_USB_STORAGE_JUMPSHOT is not set +# CONFIG_USB_STORAGE_ALAUDA is not set +# CONFIG_USB_STORAGE_ONETOUCH is not set +# CONFIG_USB_STORAGE_KARMA is not set +# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set +# CONFIG_USB_LIBUSUAL is not set + +# +# USB Imaging devices +# +# CONFIG_USB_MDC800 is not set +# CONFIG_USB_MICROTEK is not set + +# +# USB port drivers +# +# CONFIG_USB_SERIAL is not set + +# +# USB Miscellaneous drivers +# +# CONFIG_USB_EMI62 is not set +# CONFIG_USB_EMI26 is not set +# CONFIG_USB_ADUTUX is not set +# CONFIG_USB_SEVSEG is not set +# CONFIG_USB_RIO500 is not set +# CONFIG_USB_LEGOTOWER is not set +# CONFIG_USB_LCD is not set +# CONFIG_USB_BERRY_CHARGE is not set +# CONFIG_USB_LED is not set +# CONFIG_USB_CYPRESS_CY7C63 is not set +# CONFIG_USB_CYTHERM is not set +# CONFIG_USB_IDMOUSE is not set +# CONFIG_USB_FTDI_ELAN is not set +# CONFIG_USB_APPLEDISPLAY is not set +# CONFIG_USB_SISUSBVGA is not set +# CONFIG_USB_LD is not set +# CONFIG_USB_TRANCEVIBRATOR is not set +# CONFIG_USB_IOWARRIOR is not set +# CONFIG_USB_TEST is not set +# CONFIG_USB_ISIGHTFW is not set +# CONFIG_USB_VST is not set +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_DEBUG=y +CONFIG_USB_GADGET_DEBUG_FILES=y +CONFIG_USB_GADGET_VBUS_DRAW=2 +CONFIG_USB_GADGET_SELECTED=y +# CONFIG_USB_GADGET_AT91 is not set +# CONFIG_USB_GADGET_ATMEL_USBA is not set +# CONFIG_USB_GADGET_FSL_USB2 is not set +# CONFIG_USB_GADGET_LH7A40X is not set +# CONFIG_USB_GADGET_OMAP is not set +# CONFIG_USB_GADGET_PXA25X is not set +# CONFIG_USB_GADGET_R8A66597 is not set +# CONFIG_USB_GADGET_PXA27X is not set +# CONFIG_USB_GADGET_S3C_HSOTG is not set +# CONFIG_USB_GADGET_IMX is not set +# CONFIG_USB_GADGET_S3C2410 is not set +# CONFIG_USB_GADGET_M66592 is not set +# CONFIG_USB_GADGET_AMD5536UDC is not set +# CONFIG_USB_GADGET_FSL_QE is not set +# CONFIG_USB_GADGET_CI13XXX is not set +# CONFIG_USB_GADGET_NET2280 is not set +# CONFIG_USB_GADGET_GOKU is not set +# CONFIG_USB_GADGET_LANGWELL is not set +# CONFIG_USB_GADGET_DUMMY_HCD is not set +CONFIG_USB_GADGET_DUALSPEED=y +CONFIG_USB_ZERO=y +# CONFIG_USB_ZERO_HNPTEST is not set +# CONFIG_USB_AUDIO is not set +# CONFIG_USB_ETH is not set +# CONFIG_USB_GADGETFS is not set +# CONFIG_USB_FILE_STORAGE is not set +# CONFIG_USB_G_SERIAL is not set +# CONFIG_USB_MIDI_GADGET is not set +# CONFIG_USB_G_PRINTER is not set +# CONFIG_USB_CDC_COMPOSITE is not set + +# +# OTG and related infrastructure +# +CONFIG_USB_OTG_UTILS=y +# CONFIG_USB_GPIO_VBUS is not set +# CONFIG_ISP1301_OMAP is not set +CONFIG_TWL4030_USB=y +# CONFIG_NOP_USB_XCEIV is not set +CONFIG_MMC=y +# CONFIG_MMC_DEBUG is not set +# CONFIG_MMC_UNSAFE_RESUME is not set + +# +# MMC/SD/SDIO Card Drivers +# +CONFIG_MMC_BLOCK=y +CONFIG_MMC_BLOCK_BOUNCE=y +# CONFIG_SDIO_UART is not set +# CONFIG_MMC_TEST is not set + +# +# MMC/SD/SDIO Host Controller Drivers +# +# CONFIG_MMC_SDHCI is not set +# CONFIG_MMC_OMAP is not set +CONFIG_MMC_OMAP_HS=y +# CONFIG_MMC_AT91 is not set +# CONFIG_MMC_ATMELMCI is not set +# CONFIG_MMC_SPI is not set +# CONFIG_MEMSTICK is not set +# CONFIG_NEW_LEDS is not set +# CONFIG_ACCESSIBILITY is not set +CONFIG_RTC_LIB=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_HCTOSYS=y +CONFIG_RTC_HCTOSYS_DEVICE="rtc0" +# CONFIG_RTC_DEBUG is not set + +# +# RTC interfaces +# +CONFIG_RTC_INTF_SYSFS=y +CONFIG_RTC_INTF_PROC=y +CONFIG_RTC_INTF_DEV=y +# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set +# CONFIG_RTC_DRV_TEST is not set + +# +# I2C RTC drivers +# +# CONFIG_RTC_DRV_DS1307 is not set +# CONFIG_RTC_DRV_DS1374 is not set +# CONFIG_RTC_DRV_DS1672 is not set +# CONFIG_RTC_DRV_MAX6900 is not set +# CONFIG_RTC_DRV_RS5C372 is not set +# CONFIG_RTC_DRV_ISL1208 is not set +# CONFIG_RTC_DRV_X1205 is not set +# CONFIG_RTC_DRV_PCF8563 is not set +# CONFIG_RTC_DRV_PCF8583 is not set +# CONFIG_RTC_DRV_M41T80 is not set +# CONFIG_RTC_DRV_TWL4030 is not set +# CONFIG_RTC_DRV_S35390A is not set +# CONFIG_RTC_DRV_FM3130 is not set +# CONFIG_RTC_DRV_RX8581 is not set +# CONFIG_RTC_DRV_RX8025 is not set + +# +# SPI RTC drivers +# +# CONFIG_RTC_DRV_M41T94 is not set +# CONFIG_RTC_DRV_DS1305 is not set +# CONFIG_RTC_DRV_DS1390 is not set +# CONFIG_RTC_DRV_MAX6902 is not set +# CONFIG_RTC_DRV_R9701 is not set +# CONFIG_RTC_DRV_RS5C348 is not set +# CONFIG_RTC_DRV_DS3234 is not set +# CONFIG_RTC_DRV_PCF2123 is not set + +# +# Platform RTC drivers +# +# CONFIG_RTC_DRV_CMOS is not set +# CONFIG_RTC_DRV_DS1286 is not set +# CONFIG_RTC_DRV_DS1511 is not set +# CONFIG_RTC_DRV_DS1553 is not set +# CONFIG_RTC_DRV_DS1742 is not set +# CONFIG_RTC_DRV_STK17TA8 is not set +# CONFIG_RTC_DRV_M48T86 is not set +# CONFIG_RTC_DRV_M48T35 is not set +# CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_BQ4802 is not set +# CONFIG_RTC_DRV_V3020 is not set + +# +# on-CPU RTC drivers +# +# CONFIG_DMADEVICES is not set +# CONFIG_AUXDISPLAY is not set +# CONFIG_UIO is not set + +# +# TI VLYNQ +# +# CONFIG_STAGING is not set + +# +# CBUS support +# +# CONFIG_CBUS is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +CONFIG_EXT3_FS=y +# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set +# CONFIG_EXT3_FS_XATTR is not set +# CONFIG_EXT4_FS is not set +CONFIG_JBD=y +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +CONFIG_FS_POSIX_ACL=y +# CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set +# CONFIG_OCFS2_FS is not set +# CONFIG_BTRFS_FS is not set +# CONFIG_NILFS2_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y +CONFIG_DNOTIFY=y +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +CONFIG_QUOTA=y +# CONFIG_QUOTA_NETLINK_INTERFACE is not set +CONFIG_PRINT_QUOTA_WARNING=y +CONFIG_QUOTA_TREE=y +# CONFIG_QFMT_V1 is not set +CONFIG_QFMT_V2=y +CONFIG_QUOTACTL=y +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# Caches +# +# CONFIG_FSCACHE is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +CONFIG_FAT_FS=y +CONFIG_MSDOS_FS=y +CONFIG_VFAT_FS=y +CONFIG_FAT_DEFAULT_CODEPAGE=437 +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +# CONFIG_CONFIGFS_FS is not set +CONFIG_MISC_FILESYSTEMS=y +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +# CONFIG_CRAMFS is not set +# CONFIG_SQUASHFS is not set +# CONFIG_VXFS_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_OMFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_ROMFS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set +CONFIG_NETWORK_FILESYSTEMS=y +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +CONFIG_NFS_V3_ACL=y +CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set +CONFIG_ROOT_NFS=y +# CONFIG_NFSD is not set +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_NFS_ACL_SUPPORT=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +CONFIG_SUNRPC_GSS=y +CONFIG_RPCSEC_GSS_KRB5=y +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set + +# +# Partition Types +# +CONFIG_PARTITION_ADVANCED=y +# CONFIG_ACORN_PARTITION is not set +# CONFIG_OSF_PARTITION is not set +# CONFIG_AMIGA_PARTITION is not set +# CONFIG_ATARI_PARTITION is not set +# CONFIG_MAC_PARTITION is not set +CONFIG_MSDOS_PARTITION=y +# CONFIG_BSD_DISKLABEL is not set +# CONFIG_MINIX_SUBPARTITION is not set +# CONFIG_SOLARIS_X86_PARTITION is not set +# CONFIG_UNIXWARE_DISKLABEL is not set +# CONFIG_LDM_PARTITION is not set +# CONFIG_SGI_PARTITION is not set +# CONFIG_ULTRIX_PARTITION is not set +# CONFIG_SUN_PARTITION is not set +# CONFIG_KARMA_PARTITION is not set +# CONFIG_EFI_PARTITION is not set +# CONFIG_SYSV68_PARTITION is not set +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +CONFIG_NLS_CODEPAGE_437=y +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +# CONFIG_NLS_CODEPAGE_850 is not set +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +CONFIG_NLS_ISO8859_1=y +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +# CONFIG_NLS_UTF8 is not set +# CONFIG_DLM is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y +CONFIG_ENABLE_MUST_CHECK=y +CONFIG_FRAME_WARN=1024 +CONFIG_MAGIC_SYSRQ=y +# CONFIG_STRIP_ASM_SYMS is not set +# CONFIG_UNUSED_SYMBOLS is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_HEADERS_CHECK is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_DEBUG_SHIRQ is not set +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set +CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 +CONFIG_DETECT_HUNG_TASK=y +# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set +CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0 +CONFIG_SCHED_DEBUG=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_OBJECTS is not set +# CONFIG_DEBUG_SLAB is not set +# CONFIG_DEBUG_KMEMLEAK is not set +# CONFIG_DEBUG_RT_MUTEXES is not set +# CONFIG_RT_MUTEX_TESTER is not set +# CONFIG_DEBUG_SPINLOCK is not set +CONFIG_DEBUG_MUTEXES=y +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set +# CONFIG_DEBUG_KOBJECT is not set +# CONFIG_DEBUG_BUGVERBOSE is not set +CONFIG_DEBUG_INFO=y +# CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_WRITECOUNT is not set +# CONFIG_DEBUG_MEMORY_INIT is not set +# CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set +# CONFIG_DEBUG_NOTIFIERS is not set +# CONFIG_DEBUG_CREDENTIALS is not set +# CONFIG_BOOT_PRINTK_DELAY is not set +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_RCU_CPU_STALL_DETECTOR is not set +# CONFIG_BACKTRACE_SELF_TEST is not set +# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set +# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set +# CONFIG_FAULT_INJECTION is not set +# CONFIG_LATENCYTOP is not set +# CONFIG_PAGE_POISONING is not set +CONFIG_HAVE_FUNCTION_TRACER=y +CONFIG_TRACING_SUPPORT=y +CONFIG_FTRACE=y +# CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set +# CONFIG_SCHED_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set +# CONFIG_BOOT_TRACER is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set +# CONFIG_STACK_TRACER is not set +# CONFIG_KMEMTRACE is not set +# CONFIG_WORKQUEUE_TRACER is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_SAMPLES is not set +CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_KGDB is not set +CONFIG_ARM_UNWIND=y +# CONFIG_DEBUG_USER is not set +# CONFIG_DEBUG_ERRORS is not set +# CONFIG_DEBUG_STACK_USAGE is not set +# CONFIG_DEBUG_LL is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set +CONFIG_CRYPTO=y + +# +# Crypto core or helper +# +CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_ALGAPI2=y +CONFIG_CRYPTO_AEAD2=y +CONFIG_CRYPTO_BLKCIPHER=y +CONFIG_CRYPTO_BLKCIPHER2=y +CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_HASH2=y +CONFIG_CRYPTO_RNG2=y +CONFIG_CRYPTO_PCOMP=y +CONFIG_CRYPTO_MANAGER=y +CONFIG_CRYPTO_MANAGER2=y +# CONFIG_CRYPTO_GF128MUL is not set +# CONFIG_CRYPTO_NULL is not set +CONFIG_CRYPTO_WORKQUEUE=y +# CONFIG_CRYPTO_CRYPTD is not set +# CONFIG_CRYPTO_AUTHENC is not set +# CONFIG_CRYPTO_TEST is not set + +# +# Authenticated Encryption with Associated Data +# +# CONFIG_CRYPTO_CCM is not set +# CONFIG_CRYPTO_GCM is not set +# CONFIG_CRYPTO_SEQIV is not set + +# +# Block modes +# +CONFIG_CRYPTO_CBC=y +# CONFIG_CRYPTO_CTR is not set +# CONFIG_CRYPTO_CTS is not set +CONFIG_CRYPTO_ECB=m +# CONFIG_CRYPTO_LRW is not set +CONFIG_CRYPTO_PCBC=m +# CONFIG_CRYPTO_XTS is not set + +# +# Hash modes +# +# CONFIG_CRYPTO_HMAC is not set +# CONFIG_CRYPTO_XCBC is not set +# CONFIG_CRYPTO_VMAC is not set + +# +# Digest +# +CONFIG_CRYPTO_CRC32C=y +# CONFIG_CRYPTO_GHASH is not set +# CONFIG_CRYPTO_MD4 is not set +CONFIG_CRYPTO_MD5=y +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_RMD128 is not set +# CONFIG_CRYPTO_RMD160 is not set +# CONFIG_CRYPTO_RMD256 is not set +# CONFIG_CRYPTO_RMD320 is not set +# CONFIG_CRYPTO_SHA1 is not set +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_TGR192 is not set +# CONFIG_CRYPTO_WP512 is not set + +# +# Ciphers +# +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +CONFIG_CRYPTO_DES=y +# CONFIG_CRYPTO_FCRYPT is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_SALSA20 is not set +# CONFIG_CRYPTO_SEED is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_TWOFISH is not set + +# +# Compression +# +# CONFIG_CRYPTO_DEFLATE is not set +# CONFIG_CRYPTO_ZLIB is not set +# CONFIG_CRYPTO_LZO is not set + +# +# Random Number Generation +# +# CONFIG_CRYPTO_ANSI_CPRNG is not set +CONFIG_CRYPTO_HW=y +# CONFIG_BINARY_PRINTF is not set + +# +# Library routines +# +CONFIG_BITREVERSE=y +CONFIG_GENERIC_FIND_LAST_BIT=y +CONFIG_CRC_CCITT=y +# CONFIG_CRC16 is not set +CONFIG_CRC_T10DIF=y +# CONFIG_CRC_ITU_T is not set +CONFIG_CRC32=y +# CONFIG_CRC7 is not set +CONFIG_LIBCRC32C=y +CONFIG_ZLIB_INFLATE=y +CONFIG_DECOMPRESS_GZIP=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y +CONFIG_NLATTR=y -- 1.6.5.1.69.g36942 ^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH v2 7/8] omap: 3630sdp: introduce 3630 sdp board support 2009-11-10 22:47 ` [PATCH v2 6/8] omap: zoom3: defconfig creation Vikram Pandita @ 2009-11-10 22:47 ` Vikram Pandita 2009-11-10 22:47 ` [PATCH v2 8/8] omap: 3630sdp: defconfig creation Vikram Pandita 0 siblings, 1 reply; 16+ messages in thread From: Vikram Pandita @ 2009-11-10 22:47 UTC (permalink / raw) To: linux-omap; +Cc: Vikram Pandita Add 3630SDP board support The board shares the same peripherals as a zoom2 main. So reuse the peripheral file of zoom platform. Peripheral zoom2 zoom3 sdp3630 --------------------------------------- Ethernet smsc smsc smc NOR n/a n/a B Onenand n/a n/a B HDMI A A B (persent on different i2c) NAND A A A (same nand) SDRAM A A A (same sdram) Keypad A A A (same twl) Camera A A A (same sensor can be mounted) LCD Display A A A (same wvga display) OPPs A A A (same chip feature) Audio A A A (same audio via twl5030) OMAP3630 details can be found here: http://focus.ti.com/general/docs/wtbu/wtbuproductcontent.tsp?templateId=6123&navigationId=12836&contentId=52606 Signed-off-by: Vikram Pandita <vikram.pandita@ti.com> --- arch/arm/mach-omap2/Kconfig | 4 ++ arch/arm/mach-omap2/Makefile | 3 + arch/arm/mach-omap2/board-3630sdp.c | 101 +++++++++++++++++++++++++++++++++++ 3 files changed, 108 insertions(+), 0 deletions(-) create mode 100755 arch/arm/mach-omap2/board-3630sdp.c diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig index 9824775..83551a8 100644 --- a/arch/arm/mach-omap2/Kconfig +++ b/arch/arm/mach-omap2/Kconfig @@ -105,6 +105,10 @@ config MACH_OMAP_ZOOM3 bool "OMAP3630 Zoom3 board" depends on ARCH_OMAP3 && ARCH_OMAP34XX +config MACH_OMAP_3630SDP + bool "OMAP3630 SDP board" + depends on ARCH_OMAP3 && ARCH_OMAP34XX + config MACH_OMAP_4430SDP bool "OMAP 4430 SDP board" depends on ARCH_OMAP4 diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index 712e7fc..90cf2cc 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -79,6 +79,9 @@ obj-$(CONFIG_MACH_OMAP_ZOOM3) += board-zoom3.o \ board-zoom-peripherals.o \ mmc-twl4030.o \ board-zoom-debugboard.o +obj-$(CONFIG_MACH_OMAP_3630SDP) += board-3630sdp.o \ + board-zoom-peripherals.o \ + mmc-twl4030.o obj-$(CONFIG_MACH_CM_T35) += board-cm-t35.o \ mmc-twl4030.o diff --git a/arch/arm/mach-omap2/board-3630sdp.c b/arch/arm/mach-omap2/board-3630sdp.c new file mode 100755 index 0000000..f0bc5c6 --- /dev/null +++ b/arch/arm/mach-omap2/board-3630sdp.c @@ -0,0 +1,101 @@ +/* + * Copyright (C) 2009 Texas Instruments Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/input.h> +#include <linux/gpio.h> + +#include <asm/mach-types.h> +#include <asm/mach/arch.h> + +#include <plat/common.h> +#include <plat/board.h> +#include <plat/gpmc-smc91x.h> +#include <plat/mux.h> +#include <plat/usb.h> + +#include "sdram-hynix-h8mbx00u0mer-0em.h" + +#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) + +static struct omap_smc91x_platform_data board_smc91x_data = { + .cs = 3, + .flags = GPMC_MUX_ADD_DATA | IORESOURCE_IRQ_LOWLEVEL, +}; + +static void __init board_smc91x_init(void) +{ + board_smc91x_data.gpio_irq = 158; + gpmc_smc91x_init(&board_smc91x_data); +} + +#else + +static inline void board_smc91x_init(void) +{ +} + +#endif /* defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) */ + +static void enable_board_wakeup_source(void) +{ + omap_cfg_reg(AF26_34XX_SYS_NIRQ); /* T2 interrupt line (keypad) */ +} + +static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = { + + .port_mode[0] = EHCI_HCD_OMAP_MODE_PHY, + .port_mode[1] = EHCI_HCD_OMAP_MODE_PHY, + .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN, + + .phy_reset = true, + .reset_gpio_port[0] = 126, + .reset_gpio_port[1] = 61, + .reset_gpio_port[2] = -EINVAL +}; + +static void __init omap_sdp_map_io(void) +{ + omap2_set_globals_343x(); + omap2_map_common_io(); +} + +static struct omap_board_config_kernel sdp_config[] __initdata = { +}; + +static void __init omap_sdp_init_irq(void) +{ + omap_board_config = sdp_config; + omap_board_config_size = ARRAY_SIZE(sdp_config); + omap2_init_common_hw(h8mbx00u0mer0em_sdrc_params, + h8mbx00u0mer0em_sdrc_params); + omap_init_irq(); + omap_gpio_init(); +} + +extern void __init zoom_peripherals_init(void); + +static void __init omap_sdp_init(void) +{ + zoom_peripherals_init(); + board_smc91x_init(); + enable_board_wakeup_source(); + usb_ehci_init(&ehci_pdata); +} + +MACHINE_START(OMAP_3630SDP, "OMAP 3630SDP board") + .phys_io = 0x48000000, + .io_pg_offst = ((0xfa000000) >> 18) & 0xfffc, + .boot_params = 0x80000100, + .map_io = omap_sdp_map_io, + .init_irq = omap_sdp_init_irq, + .init_machine = omap_sdp_init, + .timer = &omap_timer, +MACHINE_END -- 1.6.5.1.69.g36942 ^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH v2 8/8] omap: 3630sdp: defconfig creation 2009-11-10 22:47 ` [PATCH v2 7/8] omap: 3630sdp: introduce 3630 sdp board support Vikram Pandita @ 2009-11-10 22:47 ` Vikram Pandita 0 siblings, 0 replies; 16+ messages in thread From: Vikram Pandita @ 2009-11-10 22:47 UTC (permalink / raw) To: linux-omap; +Cc: Vikram Pandita Create 3630sdp defconfig file Signed-off-by: Vikram Pandita <vikram.pandita@ti.com> --- arch/arm/configs/omap_3630sdp_defconfig | 1606 +++++++++++++++++++++++++++++++ 1 files changed, 1606 insertions(+), 0 deletions(-) create mode 100644 arch/arm/configs/omap_3630sdp_defconfig diff --git a/arch/arm/configs/omap_3630sdp_defconfig b/arch/arm/configs/omap_3630sdp_defconfig new file mode 100644 index 0000000..eb96b1a --- /dev/null +++ b/arch/arm/configs/omap_3630sdp_defconfig @@ -0,0 +1,1606 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.32-rc5 +# Tue Nov 3 14:18:44 2009 +# +CONFIG_ARM=y +CONFIG_SYS_SUPPORTS_APM_EMULATION=y +CONFIG_GENERIC_GPIO=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_HARDIRQS=y +CONFIG_STACKTRACE_SUPPORT=y +CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_LOCKDEP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_ARCH_HAS_CPUFREQ=y +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y +CONFIG_VECTORS_BASE=0xffff0000 +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y + +# +# General setup +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +CONFIG_SWAP=y +CONFIG_SYSVIPC=y +CONFIG_SYSVIPC_SYSCTL=y +# CONFIG_POSIX_MQUEUE is not set +CONFIG_BSD_PROCESS_ACCT=y +# CONFIG_BSD_PROCESS_ACCT_V3 is not set +# CONFIG_TASKSTATS is not set +# CONFIG_AUDIT is not set + +# +# RCU Subsystem +# +CONFIG_TREE_RCU=y +# CONFIG_TREE_PREEMPT_RCU is not set +# CONFIG_RCU_TRACE is not set +CONFIG_RCU_FANOUT=32 +# CONFIG_RCU_FANOUT_EXACT is not set +# CONFIG_TREE_RCU_TRACE is not set +# CONFIG_IKCONFIG is not set +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_GROUP_SCHED=y +CONFIG_FAIR_GROUP_SCHED=y +# CONFIG_RT_GROUP_SCHED is not set +CONFIG_USER_SCHED=y +# CONFIG_CGROUP_SCHED is not set +# CONFIG_CGROUPS is not set +# CONFIG_SYSFS_DEPRECATED_V2 is not set +# CONFIG_RELAY is not set +# CONFIG_NAMESPACES is not set +CONFIG_BLK_DEV_INITRD=y +CONFIG_INITRAMFS_SOURCE="" +CONFIG_RD_GZIP=y +# CONFIG_RD_BZIP2 is not set +# CONFIG_RD_LZMA is not set +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +CONFIG_SYSCTL=y +CONFIG_ANON_INODES=y +CONFIG_EMBEDDED=y +CONFIG_UID16=y +# CONFIG_SYSCTL_SYSCALL is not set +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +CONFIG_KALLSYMS_EXTRA_PASS=y +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_TIMERFD=y +CONFIG_EVENTFD=y +CONFIG_SHMEM=y +CONFIG_AIO=y + +# +# Kernel Performance Events And Counters +# +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_COMPAT_BRK=y +CONFIG_SLAB=y +# CONFIG_SLUB is not set +# CONFIG_SLOB is not set +# CONFIG_PROFILING is not set +CONFIG_HAVE_OPROFILE=y +# CONFIG_KPROBES is not set +CONFIG_HAVE_KPROBES=y +CONFIG_HAVE_KRETPROBES=y +CONFIG_HAVE_CLK=y + +# +# GCOV-based kernel profiling +# +# CONFIG_SLOW_WORK is not set +CONFIG_HAVE_GENERIC_DMA_COHERENT=y +CONFIG_SLABINFO=y +CONFIG_RT_MUTEXES=y +CONFIG_BASE_SMALL=0 +CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +CONFIG_MODVERSIONS=y +CONFIG_MODULE_SRCVERSION_ALL=y +CONFIG_BLOCK=y +CONFIG_LBDAF=y +# CONFIG_BLK_DEV_BSG is not set +# CONFIG_BLK_DEV_INTEGRITY is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" +CONFIG_FREEZER=y + +# +# System Type +# +CONFIG_MMU=y +# CONFIG_ARCH_AAEC2000 is not set +# CONFIG_ARCH_INTEGRATOR is not set +# CONFIG_ARCH_REALVIEW is not set +# CONFIG_ARCH_VERSATILE is not set +# CONFIG_ARCH_AT91 is not set +# CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_GEMINI is not set +# CONFIG_ARCH_EBSA110 is not set +# CONFIG_ARCH_EP93XX is not set +# CONFIG_ARCH_FOOTBRIDGE is not set +# CONFIG_ARCH_MXC is not set +# CONFIG_ARCH_STMP3XXX is not set +# CONFIG_ARCH_NETX is not set +# CONFIG_ARCH_H720X is not set +# CONFIG_ARCH_NOMADIK is not set +# CONFIG_ARCH_IOP13XX is not set +# CONFIG_ARCH_IOP32X is not set +# CONFIG_ARCH_IOP33X is not set +# CONFIG_ARCH_IXP23XX is not set +# CONFIG_ARCH_IXP2000 is not set +# CONFIG_ARCH_IXP4XX is not set +# CONFIG_ARCH_L7200 is not set +# CONFIG_ARCH_KIRKWOOD is not set +# CONFIG_ARCH_LOKI is not set +# CONFIG_ARCH_MV78XX0 is not set +# CONFIG_ARCH_ORION5X is not set +# CONFIG_ARCH_MMP is not set +# CONFIG_ARCH_KS8695 is not set +# CONFIG_ARCH_NS9XXX is not set +# CONFIG_ARCH_W90X900 is not set +# CONFIG_ARCH_PNX4008 is not set +# CONFIG_ARCH_PXA is not set +# CONFIG_ARCH_MSM is not set +# CONFIG_ARCH_RPC is not set +# CONFIG_ARCH_SA1100 is not set +# CONFIG_ARCH_S3C2410 is not set +# CONFIG_ARCH_S3C64XX is not set +# CONFIG_ARCH_S5PC1XX is not set +# CONFIG_ARCH_SHARK is not set +# CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_U300 is not set +# CONFIG_ARCH_DAVINCI is not set +CONFIG_ARCH_OMAP=y +# CONFIG_ARCH_BCMRING is not set + +# +# TI OMAP Implementations +# +CONFIG_ARCH_OMAP_OTG=y +# CONFIG_ARCH_OMAP1 is not set +# CONFIG_ARCH_OMAP2 is not set +CONFIG_ARCH_OMAP3=y +# CONFIG_ARCH_OMAP4 is not set + +# +# OMAP Feature Selections +# +# CONFIG_OMAP_DEBUG_POWERDOMAIN is not set +# CONFIG_OMAP_DEBUG_CLOCKDOMAIN is not set +# CONFIG_OMAP_RESET_CLOCKS is not set +CONFIG_OMAP_MUX=y +CONFIG_OMAP_MUX_DEBUG=y +CONFIG_OMAP_MUX_WARNINGS=y +CONFIG_OMAP_MCBSP=y +# CONFIG_OMAP_MBOX_FWK is not set +# CONFIG_OMAP_MPU_TIMER is not set +CONFIG_OMAP_32K_TIMER=y +CONFIG_OMAP_32K_TIMER_HZ=128 +CONFIG_OMAP_DM_TIMER=y +CONFIG_OMAP_LL_DEBUG_UART1=y +# CONFIG_OMAP_LL_DEBUG_UART2 is not set +# CONFIG_OMAP_LL_DEBUG_UART3 is not set +# CONFIG_OMAP_LL_DEBUG_NONE is not set +# CONFIG_OMAP_PM_NONE is not set +CONFIG_OMAP_PM_NOOP=y +CONFIG_ARCH_OMAP34XX=y +CONFIG_ARCH_OMAP3430=y + +# +# OMAP Board Type +# +# CONFIG_MACH_OMAP3_BEAGLE is not set +# CONFIG_MACH_OMAP_LDP is not set +# CONFIG_MACH_OVERO is not set +# CONFIG_MACH_OMAP3EVM is not set +# CONFIG_MACH_OMAP3_PANDORA is not set +# CONFIG_MACH_OMAP_3430SDP is not set +# CONFIG_MACH_NOKIA_RX51 is not set +# CONFIG_MACH_OMAP_ZOOM2 is not set +# CONFIG_MACH_CM_T35 is not set +# CONFIG_MACH_OMAP_ZOOM3 is not set +CONFIG_MACH_OMAP_3630SDP=y + +# +# Processor Type +# +CONFIG_CPU_32=y +CONFIG_CPU_32v6K=y +CONFIG_CPU_V7=y +CONFIG_CPU_32v7=y +CONFIG_CPU_ABRT_EV7=y +CONFIG_CPU_PABRT_V7=y +CONFIG_CPU_CACHE_V7=y +CONFIG_CPU_CACHE_VIPT=y +CONFIG_CPU_COPY_V6=y +CONFIG_CPU_TLB_V7=y +CONFIG_CPU_HAS_ASID=y +CONFIG_CPU_CP15=y +CONFIG_CPU_CP15_MMU=y + +# +# Processor Features +# +CONFIG_ARM_THUMB=y +# CONFIG_ARM_THUMBEE is not set +# CONFIG_CPU_ICACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_DISABLE is not set +# CONFIG_CPU_BPREDICT_DISABLE is not set +CONFIG_HAS_TLS_REG=y +CONFIG_ARM_L1_CACHE_SHIFT=6 +# CONFIG_ARM_ERRATA_430973 is not set +# CONFIG_ARM_ERRATA_458693 is not set +# CONFIG_ARM_ERRATA_460075 is not set +CONFIG_COMMON_CLKDEV=y + +# +# Bus support +# +# CONFIG_PCI_SYSCALL is not set +# CONFIG_ARCH_SUPPORTS_MSI is not set +# CONFIG_PCCARD is not set + +# +# Kernel Features +# +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +CONFIG_VMSPLIT_3G=y +# CONFIG_VMSPLIT_2G is not set +# CONFIG_VMSPLIT_1G is not set +CONFIG_PAGE_OFFSET=0xC0000000 +CONFIG_PREEMPT_NONE=y +# CONFIG_PREEMPT_VOLUNTARY is not set +# CONFIG_PREEMPT is not set +CONFIG_HZ=128 +# CONFIG_THUMB2_KERNEL is not set +CONFIG_AEABI=y +CONFIG_OABI_COMPAT=y +# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set +# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set +# CONFIG_HIGHMEM is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +CONFIG_PAGEFLAGS_EXTENDED=y +CONFIG_SPLIT_PTLOCK_CPUS=4 +# CONFIG_PHYS_ADDR_T_64BIT is not set +CONFIG_ZONE_DMA_FLAG=0 +CONFIG_VIRT_TO_BUS=y +CONFIG_HAVE_MLOCK=y +CONFIG_HAVE_MLOCKED_PAGE_BIT=y +# CONFIG_KSM is not set +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 +# CONFIG_LEDS is not set +CONFIG_ALIGNMENT_TRAP=y +# CONFIG_UACCESS_WITH_MEMCPY is not set + +# +# Boot options +# +CONFIG_ZBOOT_ROM_TEXT=0x0 +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_CMDLINE="root=/dev/nfs nfsroot=192.168.0.1:/home/user/buildroot ip=192.168.0.2:192.168.0.1:192.168.0.1:255.255.255.0:tgt:eth0:off rw console=ttyS2,115200n8" +# CONFIG_XIP_KERNEL is not set +# CONFIG_KEXEC is not set + +# +# CPU Power Management +# +# CONFIG_CPU_FREQ is not set +# CONFIG_CPU_IDLE is not set + +# +# Floating point emulation +# + +# +# At least one emulation must be selected +# +CONFIG_FPE_NWFPE=y +# CONFIG_FPE_NWFPE_XP is not set +# CONFIG_FPE_FASTFPE is not set +CONFIG_VFP=y +CONFIG_VFPv3=y +# CONFIG_NEON is not set + +# +# Userspace binary formats +# +CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +CONFIG_HAVE_AOUT=y +# CONFIG_BINFMT_AOUT is not set +CONFIG_BINFMT_MISC=y + +# +# Power management options +# +CONFIG_PM=y +CONFIG_PM_DEBUG=y +CONFIG_PM_VERBOSE=y +CONFIG_CAN_PM_TRACE=y +CONFIG_PM_SLEEP=y +CONFIG_SUSPEND=y +# CONFIG_PM_TEST_SUSPEND is not set +CONFIG_SUSPEND_FREEZER=y +# CONFIG_APM_EMULATION is not set +# CONFIG_PM_RUNTIME is not set +CONFIG_ARCH_SUSPEND_POSSIBLE=y +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +CONFIG_XFRM=y +CONFIG_XFRM_USER=y +# CONFIG_XFRM_SUB_POLICY is not set +CONFIG_XFRM_MIGRATE=y +# CONFIG_XFRM_STATISTICS is not set +CONFIG_NET_KEY=y +CONFIG_NET_KEY_MIGRATE=y +CONFIG_INET=y +CONFIG_IP_MULTICAST=y +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +CONFIG_IP_PNP_RARP=y +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_IP_MROUTE is not set +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set +CONFIG_INET_XFRM_MODE_TRANSPORT=y +CONFIG_INET_XFRM_MODE_TUNNEL=y +CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +# CONFIG_IPV6 is not set +# CONFIG_NETWORK_SECMARK is not set +# CONFIG_NETFILTER is not set +# CONFIG_IP_DCCP is not set +# CONFIG_IP_SCTP is not set +# CONFIG_RDS is not set +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set +# CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set +# CONFIG_NET_SCHED is not set +# CONFIG_DCB is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_CAN is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_AF_RXRPC is not set +# CONFIG_WIRELESS is not set +# CONFIG_WIMAX is not set +# CONFIG_RFKILL is not set +# CONFIG_NET_9P is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +# CONFIG_DEVTMPFS is not set +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_FW_LOADER is not set +# CONFIG_DEBUG_DRIVER is not set +# CONFIG_DEBUG_DEVRES is not set +# CONFIG_SYS_HYPERVISOR is not set +CONFIG_CONNECTOR=y +CONFIG_PROC_EVENTS=y +# CONFIG_MTD is not set +# CONFIG_PARPORT is not set +CONFIG_BLK_DEV=y +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=y +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +# CONFIG_BLK_DEV_NBD is not set +# CONFIG_BLK_DEV_UB is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=16384 +# CONFIG_BLK_DEV_XIP is not set +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set +# CONFIG_MG_DISK is not set +CONFIG_MISC_DEVICES=y +# CONFIG_ICS932S401 is not set +# CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_ISL29003 is not set +# CONFIG_C2PORT is not set + +# +# EEPROM support +# +# CONFIG_EEPROM_AT24 is not set +# CONFIG_EEPROM_AT25 is not set +# CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set +# CONFIG_EEPROM_93CX6 is not set +CONFIG_HAVE_IDE=y +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +CONFIG_SCSI=y +CONFIG_SCSI_DMA=y +# CONFIG_SCSI_TGT is not set +# CONFIG_SCSI_NETLINK is not set +CONFIG_SCSI_PROC_FS=y + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=y +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set +# CONFIG_BLK_DEV_SR is not set +# CONFIG_CHR_DEV_SG is not set +# CONFIG_CHR_DEV_SCH is not set +# CONFIG_SCSI_MULTI_LUN is not set +# CONFIG_SCSI_CONSTANTS is not set +# CONFIG_SCSI_LOGGING is not set +# CONFIG_SCSI_SCAN_ASYNC is not set +CONFIG_SCSI_WAIT_SCAN=m + +# +# SCSI Transports +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set +CONFIG_SCSI_LOWLEVEL=y +# CONFIG_ISCSI_TCP is not set +# CONFIG_LIBFC is not set +# CONFIG_LIBFCOE is not set +# CONFIG_SCSI_DEBUG is not set +# CONFIG_SCSI_DH is not set +# CONFIG_SCSI_OSD_INITIATOR is not set +# CONFIG_ATA is not set +# CONFIG_MD is not set +CONFIG_NETDEVICES=y +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_MACVLAN is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set +# CONFIG_VETH is not set +CONFIG_PHYLIB=y + +# +# MII PHY device drivers +# +# CONFIG_MARVELL_PHY is not set +# CONFIG_DAVICOM_PHY is not set +# CONFIG_QSEMI_PHY is not set +# CONFIG_LXT_PHY is not set +# CONFIG_CICADA_PHY is not set +# CONFIG_VITESSE_PHY is not set +CONFIG_SMSC_PHY=y +# CONFIG_BROADCOM_PHY is not set +# CONFIG_ICPLUS_PHY is not set +# CONFIG_REALTEK_PHY is not set +# CONFIG_NATIONAL_PHY is not set +# CONFIG_STE10XP is not set +# CONFIG_LSI_ET1011C_PHY is not set +# CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +# CONFIG_AX88796 is not set +CONFIG_SMC91X=y +# CONFIG_DM9000 is not set +# CONFIG_ENC28J60 is not set +# CONFIG_ETHOC is not set +# CONFIG_SMC911X is not set +# CONFIG_SMSC911X is not set +# CONFIG_DNET is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set +# CONFIG_B44 is not set +# CONFIG_KS8842 is not set +# CONFIG_KS8851 is not set +# CONFIG_KS8851_MLL is not set +CONFIG_NETDEV_1000=y +CONFIG_NETDEV_10000=y +CONFIG_WLAN=y +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set + +# +# Enable WiMAX (Networking options) to see the WiMAX drivers +# + +# +# USB Network Adapters +# +# CONFIG_USB_CATC is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_RTL8150 is not set +# CONFIG_USB_USBNET is not set +# CONFIG_WAN is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set +# CONFIG_ISDN is not set +# CONFIG_PHONE is not set + +# +# Input device support +# +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set +# CONFIG_INPUT_POLLDEV is not set + +# +# Userland interfaces +# +# CONFIG_INPUT_MOUSEDEV is not set +# CONFIG_INPUT_JOYDEV is not set +CONFIG_INPUT_EVDEV=y +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TABLET is not set +CONFIG_INPUT_TOUCHSCREEN=y +CONFIG_TOUCHSCREEN_ADS7846=y +# CONFIG_TOUCHSCREEN_AD7877 is not set +# CONFIG_TOUCHSCREEN_AD7879_I2C is not set +# CONFIG_TOUCHSCREEN_AD7879_SPI is not set +# CONFIG_TOUCHSCREEN_AD7879 is not set +# CONFIG_TOUCHSCREEN_EETI is not set +# CONFIG_TOUCHSCREEN_FUJITSU is not set +# CONFIG_TOUCHSCREEN_GUNZE is not set +# CONFIG_TOUCHSCREEN_ELO is not set +# CONFIG_TOUCHSCREEN_WACOM_W8001 is not set +# CONFIG_TOUCHSCREEN_MCS5000 is not set +# CONFIG_TOUCHSCREEN_MTOUCH is not set +# CONFIG_TOUCHSCREEN_INEXIO is not set +# CONFIG_TOUCHSCREEN_MK712 is not set +# CONFIG_TOUCHSCREEN_PENMOUNT is not set +# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set +# CONFIG_TOUCHSCREEN_TOUCHWIN is not set +# CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set +# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set +# CONFIG_TOUCHSCREEN_TSC2007 is not set +# CONFIG_TOUCHSCREEN_W90X900 is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_CONSOLE_TRANSLATIONS=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_VT_HW_CONSOLE_BINDING is not set +CONFIG_DEVKMEM=y +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_NR_UARTS=32 +CONFIG_SERIAL_8250_RUNTIME_UARTS=4 +CONFIG_SERIAL_8250_EXTENDED=y +CONFIG_SERIAL_8250_MANY_PORTS=y +CONFIG_SERIAL_8250_SHARE_IRQ=y +CONFIG_SERIAL_8250_DETECT_IRQ=y +CONFIG_SERIAL_8250_RSA=y + +# +# Non-8250 serial port support +# +# CONFIG_SERIAL_MAX3100 is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_UNIX98_PTYS=y +# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set +# CONFIG_LEGACY_PTYS is not set +# CONFIG_IPMI_HANDLER is not set +CONFIG_HW_RANDOM=y +# CONFIG_HW_RANDOM_TIMERIOMEM is not set +# CONFIG_R3964 is not set +# CONFIG_RAW_DRIVER is not set +# CONFIG_TCG_TPM is not set +CONFIG_I2C=y +CONFIG_I2C_BOARDINFO=y +CONFIG_I2C_COMPAT=y +CONFIG_I2C_CHARDEV=y +CONFIG_I2C_HELPER_AUTO=y + +# +# I2C Hardware Bus support +# + +# +# I2C system bus drivers (mostly embedded / system-on-chip) +# +# CONFIG_I2C_DESIGNWARE is not set +# CONFIG_I2C_GPIO is not set +# CONFIG_I2C_OCORES is not set +CONFIG_I2C_OMAP=y +# CONFIG_I2C_SIMTEC is not set + +# +# External I2C/SMBus adapter drivers +# +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_TAOS_EVM is not set +# CONFIG_I2C_TINY_USB is not set + +# +# Other I2C/SMBus bus drivers +# +# CONFIG_I2C_PCA_PLATFORM is not set +# CONFIG_I2C_STUB is not set + +# +# Miscellaneous I2C Chip support +# +# CONFIG_DS1682 is not set +# CONFIG_SENSORS_TSL2550 is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set +CONFIG_SPI=y +# CONFIG_SPI_DEBUG is not set +CONFIG_SPI_MASTER=y + +# +# SPI Master Controller Drivers +# +# CONFIG_SPI_BITBANG is not set +# CONFIG_SPI_GPIO is not set +CONFIG_SPI_OMAP24XX=y + +# +# SPI Protocol Masters +# +# CONFIG_SPI_SPIDEV is not set +# CONFIG_SPI_TLE62X0 is not set + +# +# PPS support +# +# CONFIG_PPS is not set +CONFIG_ARCH_REQUIRE_GPIOLIB=y +CONFIG_GPIOLIB=y +# CONFIG_DEBUG_GPIO is not set +# CONFIG_GPIO_SYSFS is not set + +# +# Memory mapped GPIO expanders: +# + +# +# I2C GPIO expanders: +# +# CONFIG_GPIO_MAX732X is not set +# CONFIG_GPIO_PCA953X is not set +# CONFIG_GPIO_PCF857X is not set +CONFIG_GPIO_TWL4030=y + +# +# PCI GPIO expanders: +# + +# +# SPI GPIO expanders: +# +# CONFIG_GPIO_MAX7301 is not set +# CONFIG_GPIO_MCP23S08 is not set +# CONFIG_GPIO_MC33880 is not set + +# +# AC97 GPIO expanders: +# +CONFIG_W1=y +CONFIG_W1_CON=y + +# +# 1-wire Bus Masters +# +# CONFIG_W1_MASTER_DS2490 is not set +# CONFIG_W1_MASTER_DS2482 is not set +# CONFIG_W1_MASTER_DS1WM is not set +# CONFIG_W1_MASTER_GPIO is not set +# CONFIG_HDQ_MASTER_OMAP is not set + +# +# 1-wire Slaves +# +# CONFIG_W1_SLAVE_THERM is not set +# CONFIG_W1_SLAVE_SMEM is not set +# CONFIG_W1_SLAVE_DS2431 is not set +# CONFIG_W1_SLAVE_DS2433 is not set +# CONFIG_W1_SLAVE_DS2760 is not set +# CONFIG_W1_SLAVE_BQ27000 is not set +CONFIG_POWER_SUPPLY=y +# CONFIG_POWER_SUPPLY_DEBUG is not set +# CONFIG_PDA_POWER is not set +# CONFIG_BATTERY_DS2760 is not set +# CONFIG_BATTERY_DS2782 is not set +# CONFIG_BATTERY_BQ27x00 is not set +# CONFIG_BATTERY_MAX17040 is not set +# CONFIG_HWMON is not set +# CONFIG_THERMAL is not set +CONFIG_WATCHDOG=y +CONFIG_WATCHDOG_NOWAYOUT=y + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set +# CONFIG_OMAP_WATCHDOG is not set +# CONFIG_TWL4030_WATCHDOG is not set + +# +# USB-based Watchdog Cards +# +# CONFIG_USBPCWATCHDOG is not set +CONFIG_SSB_POSSIBLE=y + +# +# Sonics Silicon Backplane +# +# CONFIG_SSB is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_CORE is not set +# CONFIG_MFD_SM501 is not set +# CONFIG_MFD_ASIC3 is not set +# CONFIG_HTC_EGPIO is not set +# CONFIG_HTC_PASIC3 is not set +# CONFIG_TPS65010 is not set +CONFIG_TWL4030_CORE=y +# CONFIG_TWL4030_POWER is not set +# CONFIG_MFD_TMIO is not set +# CONFIG_MFD_T7L66XB is not set +# CONFIG_MFD_TC6387XB is not set +# CONFIG_MFD_TC6393XB is not set +# CONFIG_PMIC_DA903X is not set +# CONFIG_MFD_WM8400 is not set +# CONFIG_MFD_WM831X is not set +# CONFIG_MFD_WM8350_I2C is not set +# CONFIG_MFD_PCF50633 is not set +# CONFIG_MFD_MC13783 is not set +# CONFIG_AB3100_CORE is not set +# CONFIG_EZX_PCAP is not set +CONFIG_REGULATOR=y +# CONFIG_REGULATOR_DEBUG is not set +# CONFIG_REGULATOR_FIXED_VOLTAGE is not set +# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set +# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set +# CONFIG_REGULATOR_BQ24022 is not set +# CONFIG_REGULATOR_MAX1586 is not set +CONFIG_REGULATOR_TWL4030=y +# CONFIG_REGULATOR_LP3971 is not set +# CONFIG_REGULATOR_TPS65023 is not set +# CONFIG_REGULATOR_TPS6507X is not set +# CONFIG_MEDIA_SUPPORT is not set + +# +# Graphics support +# +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=m +# CONFIG_FB is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set + +# +# Console display driver support +# +# CONFIG_VGA_CONSOLE is not set +CONFIG_DUMMY_CONSOLE=y +CONFIG_SOUND=y +# CONFIG_SOUND_OSS_CORE is not set +CONFIG_SND=y +# CONFIG_SND_SEQUENCER is not set +# CONFIG_SND_MIXER_OSS is not set +# CONFIG_SND_PCM_OSS is not set +# CONFIG_SND_HRTIMER is not set +# CONFIG_SND_DYNAMIC_MINORS is not set +CONFIG_SND_SUPPORT_OLD_API=y +CONFIG_SND_VERBOSE_PROCFS=y +# CONFIG_SND_VERBOSE_PRINTK is not set +# CONFIG_SND_DEBUG is not set +# CONFIG_SND_RAWMIDI_SEQ is not set +# CONFIG_SND_OPL3_LIB_SEQ is not set +# CONFIG_SND_OPL4_LIB_SEQ is not set +# CONFIG_SND_SBAWE_SEQ is not set +# CONFIG_SND_EMU10K1_SEQ is not set +CONFIG_SND_DRIVERS=y +# CONFIG_SND_DUMMY is not set +# CONFIG_SND_MTPAV is not set +# CONFIG_SND_SERIAL_U16550 is not set +# CONFIG_SND_MPU401 is not set +CONFIG_SND_ARM=y +CONFIG_SND_SPI=y +CONFIG_SND_USB=y +# CONFIG_SND_USB_AUDIO is not set +# CONFIG_SND_USB_CAIAQ is not set +# CONFIG_SND_SOC is not set +# CONFIG_SOUND_PRIME is not set +CONFIG_HID_SUPPORT=y +CONFIG_HID=y +# CONFIG_HIDRAW is not set + +# +# USB Input Devices +# +CONFIG_USB_HID=y +# CONFIG_HID_PID is not set +# CONFIG_USB_HIDDEV is not set + +# +# Special HID drivers +# +# CONFIG_HID_A4TECH is not set +# CONFIG_HID_APPLE is not set +# CONFIG_HID_BELKIN is not set +# CONFIG_HID_CHERRY is not set +# CONFIG_HID_CHICONY is not set +# CONFIG_HID_CYPRESS is not set +# CONFIG_HID_DRAGONRISE is not set +# CONFIG_HID_EZKEY is not set +# CONFIG_HID_KYE is not set +# CONFIG_HID_GYRATION is not set +# CONFIG_HID_TWINHAN is not set +# CONFIG_HID_KENSINGTON is not set +# CONFIG_HID_LOGITECH is not set +# CONFIG_HID_MICROSOFT is not set +# CONFIG_HID_MONTEREY is not set +# CONFIG_HID_NTRIG is not set +# CONFIG_HID_PANTHERLORD is not set +# CONFIG_HID_PETALYNX is not set +# CONFIG_HID_SAMSUNG is not set +# CONFIG_HID_SONY is not set +# CONFIG_HID_SUNPLUS is not set +# CONFIG_HID_GREENASIA is not set +# CONFIG_HID_SMARTJOYPLUS is not set +# CONFIG_HID_TOPSEED is not set +# CONFIG_HID_THRUSTMASTER is not set +# CONFIG_HID_ZEROPLUS is not set +CONFIG_USB_SUPPORT=y +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y +CONFIG_USB=y +CONFIG_USB_DEBUG=y +CONFIG_USB_ANNOUNCE_NEW_DEVICES=y + +# +# Miscellaneous USB options +# +# CONFIG_USB_DEVICEFS is not set +CONFIG_USB_DEVICE_CLASS=y +# CONFIG_USB_DYNAMIC_MINORS is not set +CONFIG_USB_SUSPEND=y +CONFIG_USB_OTG=y +# CONFIG_USB_OTG_WHITELIST is not set +# CONFIG_USB_OTG_BLACKLIST_HUB is not set +CONFIG_USB_MON=y +# CONFIG_USB_WUSB is not set +# CONFIG_USB_WUSB_CBAF is not set + +# +# USB Host Controller Drivers +# +# CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_EHCI_HCD is not set +# CONFIG_USB_OXU210HP_HCD is not set +# CONFIG_USB_ISP116X_HCD is not set +# CONFIG_USB_ISP1760_HCD is not set +# CONFIG_USB_ISP1362_HCD is not set +# CONFIG_USB_OHCI_HCD is not set +# CONFIG_USB_SL811_HCD is not set +# CONFIG_USB_R8A66597_HCD is not set +# CONFIG_USB_HWA_HCD is not set +CONFIG_USB_MUSB_HDRC=y +CONFIG_USB_MUSB_SOC=y + +# +# OMAP 343x high speed USB support +# +# CONFIG_USB_MUSB_HOST is not set +# CONFIG_USB_MUSB_PERIPHERAL is not set +CONFIG_USB_MUSB_OTG=y +CONFIG_USB_GADGET_MUSB_HDRC=y +CONFIG_USB_MUSB_HDRC_HCD=y +# CONFIG_MUSB_PIO_ONLY is not set +CONFIG_USB_INVENTRA_DMA=y +# CONFIG_USB_TI_CPPI_DMA is not set +CONFIG_USB_MUSB_DEBUG=y + +# +# USB Device Class drivers +# +# CONFIG_USB_ACM is not set +# CONFIG_USB_PRINTER is not set +# CONFIG_USB_WDM is not set +# CONFIG_USB_TMC is not set + +# +# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may +# + +# +# also be needed; see USB_STORAGE Help for more info +# +CONFIG_USB_STORAGE=y +CONFIG_USB_STORAGE_DEBUG=y +# CONFIG_USB_STORAGE_DATAFAB is not set +# CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_ISD200 is not set +# CONFIG_USB_STORAGE_USBAT is not set +# CONFIG_USB_STORAGE_SDDR09 is not set +# CONFIG_USB_STORAGE_SDDR55 is not set +# CONFIG_USB_STORAGE_JUMPSHOT is not set +# CONFIG_USB_STORAGE_ALAUDA is not set +# CONFIG_USB_STORAGE_ONETOUCH is not set +# CONFIG_USB_STORAGE_KARMA is not set +# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set +# CONFIG_USB_LIBUSUAL is not set + +# +# USB Imaging devices +# +# CONFIG_USB_MDC800 is not set +# CONFIG_USB_MICROTEK is not set + +# +# USB port drivers +# +# CONFIG_USB_SERIAL is not set + +# +# USB Miscellaneous drivers +# +# CONFIG_USB_EMI62 is not set +# CONFIG_USB_EMI26 is not set +# CONFIG_USB_ADUTUX is not set +# CONFIG_USB_SEVSEG is not set +# CONFIG_USB_RIO500 is not set +# CONFIG_USB_LEGOTOWER is not set +# CONFIG_USB_LCD is not set +# CONFIG_USB_BERRY_CHARGE is not set +# CONFIG_USB_LED is not set +# CONFIG_USB_CYPRESS_CY7C63 is not set +# CONFIG_USB_CYTHERM is not set +# CONFIG_USB_IDMOUSE is not set +# CONFIG_USB_FTDI_ELAN is not set +# CONFIG_USB_APPLEDISPLAY is not set +# CONFIG_USB_SISUSBVGA is not set +# CONFIG_USB_LD is not set +# CONFIG_USB_TRANCEVIBRATOR is not set +# CONFIG_USB_IOWARRIOR is not set +# CONFIG_USB_TEST is not set +# CONFIG_USB_ISIGHTFW is not set +# CONFIG_USB_VST is not set +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_DEBUG=y +CONFIG_USB_GADGET_DEBUG_FILES=y +CONFIG_USB_GADGET_VBUS_DRAW=2 +CONFIG_USB_GADGET_SELECTED=y +# CONFIG_USB_GADGET_AT91 is not set +# CONFIG_USB_GADGET_ATMEL_USBA is not set +# CONFIG_USB_GADGET_FSL_USB2 is not set +# CONFIG_USB_GADGET_LH7A40X is not set +# CONFIG_USB_GADGET_OMAP is not set +# CONFIG_USB_GADGET_PXA25X is not set +# CONFIG_USB_GADGET_R8A66597 is not set +# CONFIG_USB_GADGET_PXA27X is not set +# CONFIG_USB_GADGET_S3C_HSOTG is not set +# CONFIG_USB_GADGET_IMX is not set +# CONFIG_USB_GADGET_S3C2410 is not set +# CONFIG_USB_GADGET_M66592 is not set +# CONFIG_USB_GADGET_AMD5536UDC is not set +# CONFIG_USB_GADGET_FSL_QE is not set +# CONFIG_USB_GADGET_CI13XXX is not set +# CONFIG_USB_GADGET_NET2280 is not set +# CONFIG_USB_GADGET_GOKU is not set +# CONFIG_USB_GADGET_LANGWELL is not set +# CONFIG_USB_GADGET_DUMMY_HCD is not set +CONFIG_USB_GADGET_DUALSPEED=y +CONFIG_USB_ZERO=y +# CONFIG_USB_ZERO_HNPTEST is not set +# CONFIG_USB_AUDIO is not set +# CONFIG_USB_ETH is not set +# CONFIG_USB_GADGETFS is not set +# CONFIG_USB_FILE_STORAGE is not set +# CONFIG_USB_G_SERIAL is not set +# CONFIG_USB_MIDI_GADGET is not set +# CONFIG_USB_G_PRINTER is not set +# CONFIG_USB_CDC_COMPOSITE is not set + +# +# OTG and related infrastructure +# +CONFIG_USB_OTG_UTILS=y +# CONFIG_USB_GPIO_VBUS is not set +# CONFIG_ISP1301_OMAP is not set +CONFIG_TWL4030_USB=y +# CONFIG_NOP_USB_XCEIV is not set +CONFIG_MMC=y +# CONFIG_MMC_DEBUG is not set +# CONFIG_MMC_UNSAFE_RESUME is not set + +# +# MMC/SD/SDIO Card Drivers +# +CONFIG_MMC_BLOCK=y +CONFIG_MMC_BLOCK_BOUNCE=y +# CONFIG_SDIO_UART is not set +# CONFIG_MMC_TEST is not set + +# +# MMC/SD/SDIO Host Controller Drivers +# +# CONFIG_MMC_SDHCI is not set +# CONFIG_MMC_OMAP is not set +CONFIG_MMC_OMAP_HS=y +# CONFIG_MMC_AT91 is not set +# CONFIG_MMC_ATMELMCI is not set +# CONFIG_MMC_SPI is not set +# CONFIG_MEMSTICK is not set +# CONFIG_NEW_LEDS is not set +# CONFIG_ACCESSIBILITY is not set +CONFIG_RTC_LIB=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_HCTOSYS=y +CONFIG_RTC_HCTOSYS_DEVICE="rtc0" +# CONFIG_RTC_DEBUG is not set + +# +# RTC interfaces +# +CONFIG_RTC_INTF_SYSFS=y +CONFIG_RTC_INTF_PROC=y +CONFIG_RTC_INTF_DEV=y +# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set +# CONFIG_RTC_DRV_TEST is not set + +# +# I2C RTC drivers +# +# CONFIG_RTC_DRV_DS1307 is not set +# CONFIG_RTC_DRV_DS1374 is not set +# CONFIG_RTC_DRV_DS1672 is not set +# CONFIG_RTC_DRV_MAX6900 is not set +# CONFIG_RTC_DRV_RS5C372 is not set +# CONFIG_RTC_DRV_ISL1208 is not set +# CONFIG_RTC_DRV_X1205 is not set +# CONFIG_RTC_DRV_PCF8563 is not set +# CONFIG_RTC_DRV_PCF8583 is not set +# CONFIG_RTC_DRV_M41T80 is not set +# CONFIG_RTC_DRV_TWL4030 is not set +# CONFIG_RTC_DRV_S35390A is not set +# CONFIG_RTC_DRV_FM3130 is not set +# CONFIG_RTC_DRV_RX8581 is not set +# CONFIG_RTC_DRV_RX8025 is not set + +# +# SPI RTC drivers +# +# CONFIG_RTC_DRV_M41T94 is not set +# CONFIG_RTC_DRV_DS1305 is not set +# CONFIG_RTC_DRV_DS1390 is not set +# CONFIG_RTC_DRV_MAX6902 is not set +# CONFIG_RTC_DRV_R9701 is not set +# CONFIG_RTC_DRV_RS5C348 is not set +# CONFIG_RTC_DRV_DS3234 is not set +# CONFIG_RTC_DRV_PCF2123 is not set + +# +# Platform RTC drivers +# +# CONFIG_RTC_DRV_CMOS is not set +# CONFIG_RTC_DRV_DS1286 is not set +# CONFIG_RTC_DRV_DS1511 is not set +# CONFIG_RTC_DRV_DS1553 is not set +# CONFIG_RTC_DRV_DS1742 is not set +# CONFIG_RTC_DRV_STK17TA8 is not set +# CONFIG_RTC_DRV_M48T86 is not set +# CONFIG_RTC_DRV_M48T35 is not set +# CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_BQ4802 is not set +# CONFIG_RTC_DRV_V3020 is not set + +# +# on-CPU RTC drivers +# +# CONFIG_DMADEVICES is not set +# CONFIG_AUXDISPLAY is not set +# CONFIG_UIO is not set + +# +# TI VLYNQ +# +# CONFIG_STAGING is not set + +# +# CBUS support +# +# CONFIG_CBUS is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +CONFIG_EXT3_FS=y +# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set +# CONFIG_EXT3_FS_XATTR is not set +# CONFIG_EXT4_FS is not set +CONFIG_JBD=y +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +CONFIG_FS_POSIX_ACL=y +# CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set +# CONFIG_OCFS2_FS is not set +# CONFIG_BTRFS_FS is not set +# CONFIG_NILFS2_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y +CONFIG_DNOTIFY=y +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +CONFIG_QUOTA=y +# CONFIG_QUOTA_NETLINK_INTERFACE is not set +CONFIG_PRINT_QUOTA_WARNING=y +CONFIG_QUOTA_TREE=y +# CONFIG_QFMT_V1 is not set +CONFIG_QFMT_V2=y +CONFIG_QUOTACTL=y +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# Caches +# +# CONFIG_FSCACHE is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +CONFIG_FAT_FS=y +CONFIG_MSDOS_FS=y +CONFIG_VFAT_FS=y +CONFIG_FAT_DEFAULT_CODEPAGE=437 +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +# CONFIG_CONFIGFS_FS is not set +CONFIG_MISC_FILESYSTEMS=y +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +# CONFIG_CRAMFS is not set +# CONFIG_SQUASHFS is not set +# CONFIG_VXFS_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_OMFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_ROMFS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set +CONFIG_NETWORK_FILESYSTEMS=y +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +CONFIG_NFS_V3_ACL=y +CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set +CONFIG_ROOT_NFS=y +# CONFIG_NFSD is not set +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_NFS_ACL_SUPPORT=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +CONFIG_SUNRPC_GSS=y +CONFIG_RPCSEC_GSS_KRB5=y +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set + +# +# Partition Types +# +CONFIG_PARTITION_ADVANCED=y +# CONFIG_ACORN_PARTITION is not set +# CONFIG_OSF_PARTITION is not set +# CONFIG_AMIGA_PARTITION is not set +# CONFIG_ATARI_PARTITION is not set +# CONFIG_MAC_PARTITION is not set +CONFIG_MSDOS_PARTITION=y +# CONFIG_BSD_DISKLABEL is not set +# CONFIG_MINIX_SUBPARTITION is not set +# CONFIG_SOLARIS_X86_PARTITION is not set +# CONFIG_UNIXWARE_DISKLABEL is not set +# CONFIG_LDM_PARTITION is not set +# CONFIG_SGI_PARTITION is not set +# CONFIG_ULTRIX_PARTITION is not set +# CONFIG_SUN_PARTITION is not set +# CONFIG_KARMA_PARTITION is not set +# CONFIG_EFI_PARTITION is not set +# CONFIG_SYSV68_PARTITION is not set +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +CONFIG_NLS_CODEPAGE_437=y +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +# CONFIG_NLS_CODEPAGE_850 is not set +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +CONFIG_NLS_ISO8859_1=y +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +# CONFIG_NLS_UTF8 is not set +# CONFIG_DLM is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y +CONFIG_ENABLE_MUST_CHECK=y +CONFIG_FRAME_WARN=1024 +CONFIG_MAGIC_SYSRQ=y +# CONFIG_STRIP_ASM_SYMS is not set +# CONFIG_UNUSED_SYMBOLS is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_HEADERS_CHECK is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_DEBUG_SHIRQ is not set +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set +CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 +CONFIG_DETECT_HUNG_TASK=y +# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set +CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0 +CONFIG_SCHED_DEBUG=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_OBJECTS is not set +# CONFIG_DEBUG_SLAB is not set +# CONFIG_DEBUG_KMEMLEAK is not set +# CONFIG_DEBUG_RT_MUTEXES is not set +# CONFIG_RT_MUTEX_TESTER is not set +# CONFIG_DEBUG_SPINLOCK is not set +CONFIG_DEBUG_MUTEXES=y +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set +# CONFIG_DEBUG_KOBJECT is not set +# CONFIG_DEBUG_BUGVERBOSE is not set +CONFIG_DEBUG_INFO=y +# CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_WRITECOUNT is not set +# CONFIG_DEBUG_MEMORY_INIT is not set +# CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set +# CONFIG_DEBUG_NOTIFIERS is not set +# CONFIG_DEBUG_CREDENTIALS is not set +# CONFIG_BOOT_PRINTK_DELAY is not set +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_RCU_CPU_STALL_DETECTOR is not set +# CONFIG_BACKTRACE_SELF_TEST is not set +# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set +# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set +# CONFIG_FAULT_INJECTION is not set +# CONFIG_LATENCYTOP is not set +# CONFIG_PAGE_POISONING is not set +CONFIG_HAVE_FUNCTION_TRACER=y +CONFIG_TRACING_SUPPORT=y +CONFIG_FTRACE=y +# CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set +# CONFIG_SCHED_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set +# CONFIG_BOOT_TRACER is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set +# CONFIG_STACK_TRACER is not set +# CONFIG_KMEMTRACE is not set +# CONFIG_WORKQUEUE_TRACER is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_SAMPLES is not set +CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_KGDB is not set +CONFIG_ARM_UNWIND=y +# CONFIG_DEBUG_USER is not set +# CONFIG_DEBUG_ERRORS is not set +# CONFIG_DEBUG_STACK_USAGE is not set +CONFIG_DEBUG_LL=y +# CONFIG_DEBUG_ICEDCC is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set +CONFIG_CRYPTO=y + +# +# Crypto core or helper +# +CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_ALGAPI2=y +CONFIG_CRYPTO_AEAD2=y +CONFIG_CRYPTO_BLKCIPHER=y +CONFIG_CRYPTO_BLKCIPHER2=y +CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_HASH2=y +CONFIG_CRYPTO_RNG2=y +CONFIG_CRYPTO_PCOMP=y +CONFIG_CRYPTO_MANAGER=y +CONFIG_CRYPTO_MANAGER2=y +# CONFIG_CRYPTO_GF128MUL is not set +# CONFIG_CRYPTO_NULL is not set +CONFIG_CRYPTO_WORKQUEUE=y +# CONFIG_CRYPTO_CRYPTD is not set +# CONFIG_CRYPTO_AUTHENC is not set +# CONFIG_CRYPTO_TEST is not set + +# +# Authenticated Encryption with Associated Data +# +# CONFIG_CRYPTO_CCM is not set +# CONFIG_CRYPTO_GCM is not set +# CONFIG_CRYPTO_SEQIV is not set + +# +# Block modes +# +CONFIG_CRYPTO_CBC=y +# CONFIG_CRYPTO_CTR is not set +# CONFIG_CRYPTO_CTS is not set +CONFIG_CRYPTO_ECB=m +# CONFIG_CRYPTO_LRW is not set +CONFIG_CRYPTO_PCBC=m +# CONFIG_CRYPTO_XTS is not set + +# +# Hash modes +# +# CONFIG_CRYPTO_HMAC is not set +# CONFIG_CRYPTO_XCBC is not set +# CONFIG_CRYPTO_VMAC is not set + +# +# Digest +# +CONFIG_CRYPTO_CRC32C=y +# CONFIG_CRYPTO_GHASH is not set +# CONFIG_CRYPTO_MD4 is not set +CONFIG_CRYPTO_MD5=y +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_RMD128 is not set +# CONFIG_CRYPTO_RMD160 is not set +# CONFIG_CRYPTO_RMD256 is not set +# CONFIG_CRYPTO_RMD320 is not set +# CONFIG_CRYPTO_SHA1 is not set +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_TGR192 is not set +# CONFIG_CRYPTO_WP512 is not set + +# +# Ciphers +# +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +CONFIG_CRYPTO_DES=y +# CONFIG_CRYPTO_FCRYPT is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_SALSA20 is not set +# CONFIG_CRYPTO_SEED is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_TWOFISH is not set + +# +# Compression +# +# CONFIG_CRYPTO_DEFLATE is not set +# CONFIG_CRYPTO_ZLIB is not set +# CONFIG_CRYPTO_LZO is not set + +# +# Random Number Generation +# +# CONFIG_CRYPTO_ANSI_CPRNG is not set +CONFIG_CRYPTO_HW=y +# CONFIG_BINARY_PRINTF is not set + +# +# Library routines +# +CONFIG_BITREVERSE=y +CONFIG_GENERIC_FIND_LAST_BIT=y +CONFIG_CRC_CCITT=y +# CONFIG_CRC16 is not set +CONFIG_CRC_T10DIF=y +# CONFIG_CRC_ITU_T is not set +CONFIG_CRC32=y +# CONFIG_CRC7 is not set +CONFIG_LIBCRC32C=y +CONFIG_ZLIB_INFLATE=y +CONFIG_DECOMPRESS_GZIP=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y +CONFIG_NLATTR=y -- 1.6.5.1.69.g36942 ^ permalink raw reply related [flat|nested] 16+ messages in thread
* Re: [PATCH v2 3/8] omap: zoom2: split board file for software reuse 2009-11-10 22:47 ` [PATCH v2 3/8] omap: zoom2: split board file for software reuse Vikram Pandita 2009-11-10 22:47 ` [PATCH v2 4/8] omap: zoom2: update defconfig for LL_DEBUG_NONE Vikram Pandita @ 2009-11-11 1:24 ` Tony Lindgren 1 sibling, 0 replies; 16+ messages in thread From: Tony Lindgren @ 2009-11-11 1:24 UTC (permalink / raw) To: Vikram Pandita; +Cc: linux-omap * Vikram Pandita <vikram.pandita@ti.com> [091110 14:48]: > Split zoom2 board file into: > base board file and a board-zoom-peripherals.c file > > that way the same peripherals file can be reused for: zoom3 and sdp3630 > > Following list shows the commonality across the three platforms and hence the > case for software reuse: > > Peripheral zoom2 zoom3 sdp3630 > --------------------------------------- > Ethernet smsc smsc smc > NOR n/a n/a B > Onenand n/a n/a B > HDMI A A B (present on different i2c) > NAND A A A (same nand) > SDRAM A A A (same sdram) > Keypad A A A (same twl) > Camera A A A (same sensor can be mounted) > LCD Display A A A (same wvga display) > OPPs A A A (same chip feature) > Audio A A A (same audio via twl5030) Thanks for pulling together all the 3630 patches! Can you please do this one in two steps: 1. Move the existing functions to board-zoom-peripherals.c without renaming or changing anything except minimal changes to compile. 2. Do the desired renames and changes. Then resend the patches using -M option for git to detect renames ;) That way it will be easy for everybody to see what exactly got changed. Regards, Tony > Signed-off-by: Vikram Pandita <vikram.pandita@ti.com> > --- > arch/arm/mach-omap2/Makefile | 1 + > arch/arm/mach-omap2/board-zoom-peripherals.c | 278 ++++++++++++++++++++++++++ > arch/arm/mach-omap2/board-zoom2.c | 247 +---------------------- > 3 files changed, 286 insertions(+), 240 deletions(-) > create mode 100644 arch/arm/mach-omap2/board-zoom-peripherals.c > > diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile > index 03cb4fc..4d66b42 100644 > --- a/arch/arm/mach-omap2/Makefile > +++ b/arch/arm/mach-omap2/Makefile > @@ -72,6 +72,7 @@ obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51.o \ > board-rx51-peripherals.o \ > mmc-twl4030.o > obj-$(CONFIG_MACH_OMAP_ZOOM2) += board-zoom2.o \ > + board-zoom-peripherals.o \ > mmc-twl4030.o \ > board-zoom-debugboard.o > obj-$(CONFIG_MACH_CM_T35) += board-cm-t35.o \ > diff --git a/arch/arm/mach-omap2/board-zoom-peripherals.c b/arch/arm/mach-omap2/board-zoom-peripherals.c > new file mode 100644 > index 0000000..d872588 > --- /dev/null > +++ b/arch/arm/mach-omap2/board-zoom-peripherals.c > @@ -0,0 +1,278 @@ > +/* > + * Copyright (C) 2009 Texas Instruments Inc. > + * > + * Modified from mach-omap2/board-zoom2.c > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + */ > + > +#include <linux/kernel.h> > +#include <linux/init.h> > +#include <linux/platform_device.h> > +#include <linux/input.h> > +#include <linux/input/matrix_keypad.h> > +#include <linux/gpio.h> > +#include <linux/i2c/twl4030.h> > +#include <linux/regulator/machine.h> > + > +#include <asm/mach-types.h> > +#include <asm/mach/arch.h> > +#include <asm/mach/map.h> > + > +#include <plat/common.h> > +#include <plat/usb.h> > + > +#include "mmc-twl4030.h" > + > +/* Zoom2 has Qwerty keyboard*/ > +static int zoom_board_keymap[] = { > + KEY(0, 0, KEY_E), > + KEY(1, 0, KEY_R), > + KEY(2, 0, KEY_T), > + KEY(3, 0, KEY_HOME), > + KEY(6, 0, KEY_I), > + KEY(7, 0, KEY_LEFTSHIFT), > + KEY(0, 1, KEY_D), > + KEY(1, 1, KEY_F), > + KEY(2, 1, KEY_G), > + KEY(3, 1, KEY_SEND), > + KEY(6, 1, KEY_K), > + KEY(7, 1, KEY_ENTER), > + KEY(0, 2, KEY_X), > + KEY(1, 2, KEY_C), > + KEY(2, 2, KEY_V), > + KEY(3, 2, KEY_END), > + KEY(6, 2, KEY_DOT), > + KEY(7, 2, KEY_CAPSLOCK), > + KEY(0, 3, KEY_Z), > + KEY(1, 3, KEY_KPPLUS), > + KEY(2, 3, KEY_B), > + KEY(3, 3, KEY_F1), > + KEY(6, 3, KEY_O), > + KEY(7, 3, KEY_SPACE), > + KEY(0, 4, KEY_W), > + KEY(1, 4, KEY_Y), > + KEY(2, 4, KEY_U), > + KEY(3, 4, KEY_F2), > + KEY(4, 4, KEY_VOLUMEUP), > + KEY(6, 4, KEY_L), > + KEY(7, 4, KEY_LEFT), > + KEY(0, 5, KEY_S), > + KEY(1, 5, KEY_H), > + KEY(2, 5, KEY_J), > + KEY(3, 5, KEY_F3), > + KEY(5, 5, KEY_VOLUMEDOWN), > + KEY(6, 5, KEY_M), > + KEY(4, 5, KEY_ENTER), > + KEY(7, 5, KEY_RIGHT), > + KEY(0, 6, KEY_Q), > + KEY(1, 6, KEY_A), > + KEY(2, 6, KEY_N), > + KEY(3, 6, KEY_BACKSPACE), > + KEY(6, 6, KEY_P), > + KEY(7, 6, KEY_UP), > + KEY(6, 7, KEY_SELECT), > + KEY(7, 7, KEY_DOWN), > + KEY(0, 7, KEY_PROG1), /*MACRO 1 <User defined> */ > + KEY(1, 7, KEY_PROG2), /*MACRO 2 <User defined> */ > + KEY(2, 7, KEY_PROG3), /*MACRO 3 <User defined> */ > + KEY(3, 7, KEY_PROG4), /*MACRO 4 <User defined> */ > + 0 > +}; > + > +static struct matrix_keymap_data zoom_board_map_data = { > + .keymap = zoom_board_keymap, > + .keymap_size = ARRAY_SIZE(zoom_board_keymap), > +}; > + > +static struct twl4030_keypad_data zoom_kp_twl4030_data = { > + .keymap_data = &zoom_board_map_data, > + .rows = 8, > + .cols = 8, > + .rep = 1, > +}; > + > +static struct twl4030_madc_platform_data zoom_madc_data = { > + .irq_line = 1, > +}; > + > +static struct twl4030_hsmmc_info zoom_mmc[] = { > + { > + .name = "external", > + .mmc = 1, > + .wires = 4, > + .cover_only = true, > + .gpio_cd = -EINVAL, > + .gpio_wp = -EINVAL, > + .power_saving = true, > + }, > + { > + .name = "internal", > + .mmc = 2, > + .wires = 8, > + .gpio_cd = -EINVAL, > + .gpio_wp = -EINVAL, > + .nonremovable = true, > + .power_saving = true, > + }, > + {} /* Terminator */ > +}; > + > +static struct regulator_consumer_supply zoom_vmmc1_supply = { > + .supply = "vmmc", > +}; > + > +static struct regulator_consumer_supply zoom_vmmc2_supply = { > + .supply = "vmmc", > +}; > + > +static struct regulator_consumer_supply zoom_vsim_supply = { > + .supply = "vmmc_aux", > +}; > + > +/* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */ > +static struct regulator_init_data zoom_vmmc1 = { > + .constraints = { > + .min_uV = 1850000, > + .max_uV = 3150000, > + .valid_modes_mask = REGULATOR_MODE_NORMAL > + | REGULATOR_MODE_STANDBY, > + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE > + | REGULATOR_CHANGE_MODE > + | REGULATOR_CHANGE_STATUS, > + }, > + .num_consumer_supplies = 1, > + .consumer_supplies = &zoom_vmmc1_supply, > +}; > + > +/* VMMC2 for MMC2 card */ > +static struct regulator_init_data zoom_vmmc2 = { > + .constraints = { > + .name = "VMMC2_30", > + .min_uV = 1850000, > + .max_uV = 1850000, > + .apply_uV = true, > + .valid_modes_mask = REGULATOR_MODE_NORMAL > + | REGULATOR_MODE_STANDBY, > + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE > + | REGULATOR_CHANGE_MODE > + | REGULATOR_CHANGE_STATUS, > + }, > + .num_consumer_supplies = 1, > + .consumer_supplies = &zoom_vmmc2_supply, > +}; > + > +/* VSIM for OMAP VDD_MMC1A (i/o for DAT4..DAT7) */ > +static struct regulator_init_data zoom_vsim = { > + .constraints = { > + .name = "VMMC2_IO_18", > + .min_uV = 1800000, > + .max_uV = 3000000, > + .apply_uV = true, > + .valid_modes_mask = REGULATOR_MODE_NORMAL > + | REGULATOR_MODE_STANDBY, > + .valid_ops_mask = REGULATOR_CHANGE_MODE > + | REGULATOR_CHANGE_STATUS, > + }, > + .num_consumer_supplies = 1, > + .consumer_supplies = &zoom_vsim_supply, > +}; > + > +static int zoom_twl_gpio_setup(struct device *dev, > + unsigned gpio, unsigned ngpio) > +{ > + /* gpio + 0 is "mmc0_cd" (input/IRQ), > + * gpio + 1 is "mmc1_cd" (input/IRQ) > + */ > + zoom_mmc[0].gpio_cd = gpio + 0; > + zoom_mmc[1].gpio_cd = gpio + 1; > + twl4030_mmc_init(zoom_mmc); > + > + /* link regulators to MMC adapters ... we "know" the > + * regulators will be set up only *after* we return. > + */ > + zoom_vmmc1_supply.dev = zoom_mmc[0].dev; > + zoom_vmmc2_supply.dev = zoom_mmc[1].dev; > + zoom_vsim_supply.dev = zoom_mmc[0].dev; > + > + return 0; > +} > + > +static struct twl4030_gpio_platform_data zoom_gpio_data = { > + .gpio_base = OMAP_MAX_GPIO_LINES, > + .irq_base = TWL4030_GPIO_IRQ_BASE, > + .irq_end = TWL4030_GPIO_IRQ_END, > + .setup = zoom_twl_gpio_setup, > +}; > + > +static struct twl4030_usb_data zoom_usb_data = { > + .usb_mode = T2_USB_MODE_ULPI, > +}; > + > +static int zoom_batt_table[] = { > +/* 0 C*/ > +30800, 29500, 28300, 27100, > +26000, 24900, 23900, 22900, 22000, 21100, 20300, 19400, 18700, 17900, > +17200, 16500, 15900, 15300, 14700, 14100, 13600, 13100, 12600, 12100, > +11600, 11200, 10800, 10400, 10000, 9630, 9280, 8950, 8620, 8310, > +8020, 7730, 7460, 7200, 6950, 6710, 6470, 6250, 6040, 5830, > +5640, 5450, 5260, 5090, 4920, 4760, 4600, 4450, 4310, 4170, > +4040, 3910, 3790, 3670, 3550 > +}; > + > +static struct twl4030_bci_platform_data zoom_bci_data = { > + .battery_tmp_tbl = zoom_batt_table, > + .tblsize = ARRAY_SIZE(zoom_batt_table), > +}; > + > +static struct twl4030_platform_data zoom_twldata = { > + .irq_base = TWL4030_IRQ_BASE, > + .irq_end = TWL4030_IRQ_END, > + > + /* platform_data for children goes here */ > + .bci = &zoom_bci_data, > + .madc = &zoom_madc_data, > + .usb = &zoom_usb_data, > + .gpio = &zoom_gpio_data, > + .keypad = &zoom_kp_twl4030_data, > + .vmmc1 = &zoom_vmmc1, > + .vmmc2 = &zoom_vmmc2, > + .vsim = &zoom_vsim, > +}; > + > +static struct i2c_board_info __initdata zoom_i2c_boardinfo[] = { > + { > + I2C_BOARD_INFO("twl5030", 0x48), > + .flags = I2C_CLIENT_WAKE, > + .irq = INT_34XX_SYS_NIRQ, > + .platform_data = &zoom_twldata, > + }, > +}; > + > +static int __init zoom_i2c_init(void) > +{ > + omap_register_i2c_bus(1, 2200, zoom_i2c_boardinfo, > + ARRAY_SIZE(zoom_i2c_boardinfo)); > + > + /* TODO: I2C2 on zoom2/3: > + * Add Synaptic RMI controller > + * Add Camera sensor IMX046 > + * Add Camera sensor LV8093 > + */ > + omap_register_i2c_bus(2, 100, NULL, 0); > + > + /* TODO: I2C3 on Zoom2/3: > + * Add: SIL9022 HDMI > + */ > + omap_register_i2c_bus(3, 100, NULL, 0); > + return 0; > +} > + > +void __init zoom_peripherals_init(void) > +{ > + zoom_i2c_init(); > + omap_serial_init(); > + usb_musb_init(); > +} > diff --git a/arch/arm/mach-omap2/board-zoom2.c b/arch/arm/mach-omap2/board-zoom2.c > index 4ad9b94..1330915 100644 > --- a/arch/arm/mach-omap2/board-zoom2.c > +++ b/arch/arm/mach-omap2/board-zoom2.c > @@ -1,8 +1,6 @@ > /* > * Copyright (C) 2009 Texas Instruments Inc. > - * Mikkel Christensen <mlc@ti.com> > * > - * Modified from mach-omap2/board-ldp.c > * > * This program is free software; you can redistribute it and/or modify > * it under the terms of the GNU General Public License version 2 as > @@ -13,203 +11,24 @@ > #include <linux/init.h> > #include <linux/platform_device.h> > #include <linux/input.h> > -#include <linux/input/matrix_keypad.h> > #include <linux/gpio.h> > -#include <linux/i2c/twl4030.h> > -#include <linux/regulator/machine.h> > > #include <asm/mach-types.h> > #include <asm/mach/arch.h> > > #include <plat/common.h> > -#include <plat/usb.h> > +#include <plat/board.h> > > -#include "mmc-twl4030.h" > #include "sdram-micron-mt46h32m32lf-6.h" > > -/* Zoom2 has Qwerty keyboard*/ > -static int board_keymap[] = { > - KEY(0, 0, KEY_E), > - KEY(1, 0, KEY_R), > - KEY(2, 0, KEY_T), > - KEY(3, 0, KEY_HOME), > - KEY(6, 0, KEY_I), > - KEY(7, 0, KEY_LEFTSHIFT), > - KEY(0, 1, KEY_D), > - KEY(1, 1, KEY_F), > - KEY(2, 1, KEY_G), > - KEY(3, 1, KEY_SEND), > - KEY(6, 1, KEY_K), > - KEY(7, 1, KEY_ENTER), > - KEY(0, 2, KEY_X), > - KEY(1, 2, KEY_C), > - KEY(2, 2, KEY_V), > - KEY(3, 2, KEY_END), > - KEY(6, 2, KEY_DOT), > - KEY(7, 2, KEY_CAPSLOCK), > - KEY(0, 3, KEY_Z), > - KEY(1, 3, KEY_KPPLUS), > - KEY(2, 3, KEY_B), > - KEY(3, 3, KEY_F1), > - KEY(6, 3, KEY_O), > - KEY(7, 3, KEY_SPACE), > - KEY(0, 4, KEY_W), > - KEY(1, 4, KEY_Y), > - KEY(2, 4, KEY_U), > - KEY(3, 4, KEY_F2), > - KEY(4, 4, KEY_VOLUMEUP), > - KEY(6, 4, KEY_L), > - KEY(7, 4, KEY_LEFT), > - KEY(0, 5, KEY_S), > - KEY(1, 5, KEY_H), > - KEY(2, 5, KEY_J), > - KEY(3, 5, KEY_F3), > - KEY(5, 5, KEY_VOLUMEDOWN), > - KEY(6, 5, KEY_M), > - KEY(4, 5, KEY_ENTER), > - KEY(7, 5, KEY_RIGHT), > - KEY(0, 6, KEY_Q), > - KEY(1, 6, KEY_A), > - KEY(2, 6, KEY_N), > - KEY(3, 6, KEY_BACKSPACE), > - KEY(6, 6, KEY_P), > - KEY(7, 6, KEY_UP), > - KEY(6, 7, KEY_SELECT), > - KEY(7, 7, KEY_DOWN), > - KEY(0, 7, KEY_PROG1), /*MACRO 1 <User defined> */ > - KEY(1, 7, KEY_PROG2), /*MACRO 2 <User defined> */ > - KEY(2, 7, KEY_PROG3), /*MACRO 3 <User defined> */ > - KEY(3, 7, KEY_PROG4), /*MACRO 4 <User defined> */ > - 0 > -}; > - > -static struct matrix_keymap_data board_map_data = { > - .keymap = board_keymap, > - .keymap_size = ARRAY_SIZE(board_keymap), > -}; > - > -static struct twl4030_keypad_data zoom2_kp_twl4030_data = { > - .keymap_data = &board_map_data, > - .rows = 8, > - .cols = 8, > - .rep = 1, > -}; > - > -static struct omap_board_config_kernel zoom2_config[] __initdata = { > -}; > - > -static struct regulator_consumer_supply zoom2_vmmc1_supply = { > - .supply = "vmmc", > -}; > - > -static struct regulator_consumer_supply zoom2_vsim_supply = { > - .supply = "vmmc_aux", > -}; > - > -static struct regulator_consumer_supply zoom2_vmmc2_supply = { > - .supply = "vmmc", > -}; > - > -/* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */ > -static struct regulator_init_data zoom2_vmmc1 = { > - .constraints = { > - .min_uV = 1850000, > - .max_uV = 3150000, > - .valid_modes_mask = REGULATOR_MODE_NORMAL > - | REGULATOR_MODE_STANDBY, > - .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE > - | REGULATOR_CHANGE_MODE > - | REGULATOR_CHANGE_STATUS, > - }, > - .num_consumer_supplies = 1, > - .consumer_supplies = &zoom2_vmmc1_supply, > -}; > - > -/* VMMC2 for MMC2 card */ > -static struct regulator_init_data zoom2_vmmc2 = { > - .constraints = { > - .min_uV = 1850000, > - .max_uV = 1850000, > - .apply_uV = true, > - .valid_modes_mask = REGULATOR_MODE_NORMAL > - | REGULATOR_MODE_STANDBY, > - .valid_ops_mask = REGULATOR_CHANGE_MODE > - | REGULATOR_CHANGE_STATUS, > - }, > - .num_consumer_supplies = 1, > - .consumer_supplies = &zoom2_vmmc2_supply, > -}; > - > -/* VSIM for OMAP VDD_MMC1A (i/o for DAT4..DAT7) */ > -static struct regulator_init_data zoom2_vsim = { > - .constraints = { > - .min_uV = 1800000, > - .max_uV = 3000000, > - .valid_modes_mask = REGULATOR_MODE_NORMAL > - | REGULATOR_MODE_STANDBY, > - .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE > - | REGULATOR_CHANGE_MODE > - | REGULATOR_CHANGE_STATUS, > - }, > - .num_consumer_supplies = 1, > - .consumer_supplies = &zoom2_vsim_supply, > -}; > - > -static struct twl4030_hsmmc_info mmc[] __initdata = { > - { > - .mmc = 1, > - .wires = 4, > - .gpio_wp = -EINVAL, > - }, > - { > - .mmc = 2, > - .wires = 4, > - .gpio_wp = -EINVAL, > - }, > - {} /* Terminator */ > -}; > - > -static int zoom2_twl_gpio_setup(struct device *dev, > - unsigned gpio, unsigned ngpio) > +static void __init omap_zoom2_map_io(void) > { > - /* gpio + 0 is "mmc0_cd" (input/IRQ), > - * gpio + 1 is "mmc1_cd" (input/IRQ) > - */ > - mmc[0].gpio_cd = gpio + 0; > - mmc[1].gpio_cd = gpio + 1; > - twl4030_mmc_init(mmc); > - > - /* link regulators to MMC adapters ... we "know" the > - * regulators will be set up only *after* we return. > - */ > - zoom2_vmmc1_supply.dev = mmc[0].dev; > - zoom2_vsim_supply.dev = mmc[0].dev; > - zoom2_vmmc2_supply.dev = mmc[1].dev; > - > - return 0; > + omap2_set_globals_343x(); > + omap2_map_common_io(); > } > > - > -static int zoom2_batt_table[] = { > -/* 0 C*/ > -30800, 29500, 28300, 27100, > -26000, 24900, 23900, 22900, 22000, 21100, 20300, 19400, 18700, 17900, > -17200, 16500, 15900, 15300, 14700, 14100, 13600, 13100, 12600, 12100, > -11600, 11200, 10800, 10400, 10000, 9630, 9280, 8950, 8620, 8310, > -8020, 7730, 7460, 7200, 6950, 6710, 6470, 6250, 6040, 5830, > -5640, 5450, 5260, 5090, 4920, 4760, 4600, 4450, 4310, 4170, > -4040, 3910, 3790, 3670, 3550 > -}; > - > -static struct twl4030_bci_platform_data zoom2_bci_data = { > - .battery_tmp_tbl = zoom2_batt_table, > - .tblsize = ARRAY_SIZE(zoom2_batt_table), > -}; > - > -static struct twl4030_usb_data zoom2_usb_data = { > - .usb_mode = T2_USB_MODE_ULPI, > +static struct omap_board_config_kernel zoom2_config[] __initdata = { > }; > - > static void __init omap_zoom2_init_irq(void) > { > omap_board_config = zoom2_config; > @@ -220,65 +39,13 @@ static void __init omap_zoom2_init_irq(void) > omap_gpio_init(); > } > > -static struct twl4030_gpio_platform_data zoom2_gpio_data = { > - .gpio_base = OMAP_MAX_GPIO_LINES, > - .irq_base = TWL4030_GPIO_IRQ_BASE, > - .irq_end = TWL4030_GPIO_IRQ_END, > - .setup = zoom2_twl_gpio_setup, > -}; > - > -static struct twl4030_madc_platform_data zoom2_madc_data = { > - .irq_line = 1, > -}; > - > -static struct twl4030_platform_data zoom2_twldata = { > - .irq_base = TWL4030_IRQ_BASE, > - .irq_end = TWL4030_IRQ_END, > - > - /* platform_data for children goes here */ > - .bci = &zoom2_bci_data, > - .madc = &zoom2_madc_data, > - .usb = &zoom2_usb_data, > - .gpio = &zoom2_gpio_data, > - .keypad = &zoom2_kp_twl4030_data, > - .vmmc1 = &zoom2_vmmc1, > - .vmmc2 = &zoom2_vmmc2, > - .vsim = &zoom2_vsim, > - > -}; > - > -static struct i2c_board_info __initdata zoom2_i2c_boardinfo[] = { > - { > - I2C_BOARD_INFO("twl4030", 0x48), > - .flags = I2C_CLIENT_WAKE, > - .irq = INT_34XX_SYS_NIRQ, > - .platform_data = &zoom2_twldata, > - }, > -}; > - > -static int __init omap_i2c_init(void) > -{ > - omap_register_i2c_bus(1, 2600, zoom2_i2c_boardinfo, > - ARRAY_SIZE(zoom2_i2c_boardinfo)); > - omap_register_i2c_bus(2, 400, NULL, 0); > - omap_register_i2c_bus(3, 400, NULL, 0); > - return 0; > -} > - > extern int __init omap_zoom2_debugboard_init(void); > +extern void __init zoom_peripherals_init(void); > > static void __init omap_zoom2_init(void) > { > - omap_i2c_init(); > - omap_serial_init(); > + zoom_peripherals_init(); > omap_zoom2_debugboard_init(); > - usb_musb_init(); > -} > - > -static void __init omap_zoom2_map_io(void) > -{ > - omap2_set_globals_343x(); > - omap2_map_common_io(); > } > > MACHINE_START(OMAP_ZOOM2, "OMAP Zoom2 board") > -- > 1.6.5.1.69.g36942 > > -- > To unsubscribe from this list: send the line "unsubscribe linux-omap" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 16+ messages in thread
* [APPLIED] [PATCH v2 2/8] omap: introduce OMAP_LL_DEBUG_NONE DEBUG_LL config 2009-11-10 22:47 ` [PATCH v2 2/8] omap: introduce OMAP_LL_DEBUG_NONE DEBUG_LL config Vikram Pandita 2009-11-10 22:47 ` [PATCH v2 3/8] omap: zoom2: split board file for software reuse Vikram Pandita @ 2009-11-11 1:32 ` Tony Lindgren 1 sibling, 0 replies; 16+ messages in thread From: Tony Lindgren @ 2009-11-11 1:32 UTC (permalink / raw) To: linux-omap This patch has been applied to the linux-omap by youw fwiendly patch wobot. Branch in linux-omap: for-next Initial commit ID (Likely to change): 6c6b4924e24051c432259f3ee917cd08aabdc0ec PatchWorks http://patchwork.kernel.org/patch/59197/ Git (Likely to change, and takes a while to get mirrored) http://git.kernel.org/?p=linux/kernel/git/tmlind/linux-omap-2.6.git;a=commit;h=6c6b4924e24051c432259f3ee917cd08aabdc0ec ^ permalink raw reply [flat|nested] 16+ messages in thread
* [APPLIED] [PATCH v2 1/8] omap: 3630: update is_chip variable 2009-11-10 22:47 ` [PATCH v2 1/8] omap: 3630: update is_chip variable Vikram Pandita 2009-11-10 22:47 ` [PATCH v2 2/8] omap: introduce OMAP_LL_DEBUG_NONE DEBUG_LL config Vikram Pandita @ 2009-11-11 1:27 ` Tony Lindgren 1 sibling, 0 replies; 16+ messages in thread From: Tony Lindgren @ 2009-11-11 1:27 UTC (permalink / raw) To: linux-omap This patch has been applied to the linux-omap by youw fwiendly patch wobot. Branch in linux-omap: for-next Initial commit ID (Likely to change): 4d2b130c190627af16cb7b9961da037436ad6d36 PatchWorks http://patchwork.kernel.org/patch/59199/ Git (Likely to change, and takes a while to get mirrored) http://git.kernel.org/?p=linux/kernel/git/tmlind/linux-omap-2.6.git;a=commit;h=4d2b130c190627af16cb7b9961da037436ad6d36 ^ permalink raw reply [flat|nested] 16+ messages in thread
* RE: [PATCH v2 0/8] introduce 3630 boards 2009-11-10 22:47 [PATCH v2 0/8] introduce 3630 boards Vikram Pandita 2009-11-10 22:47 ` [PATCH v2 1/8] omap: 3630: update is_chip variable Vikram Pandita @ 2009-11-11 15:15 ` Gadiyar, Anand 2009-11-11 15:19 ` Gadiyar, Anand 2 siblings, 0 replies; 16+ messages in thread From: Gadiyar, Anand @ 2009-11-11 15:15 UTC (permalink / raw) To: Pandita, Vikram, linux-omap@vger.kernel.org > -----Original Message----- > From: linux-omap-owner@vger.kernel.org > [mailto:linux-omap-owner@vger.kernel.org] On Behalf Of Pandita, Vikram > Sent: Wednesday, November 11, 2009 4:17 AM > To: linux-omap@vger.kernel.org > Cc: Pandita, Vikram > Subject: [PATCH v2 0/8] introduce 3630 boards > > Introducing 3630 boards: zoom3 and sdp3630 > > The peripherals are very similar for the two bards as per > this discussion: > http://marc.info/?l=linux-omap&m=125676595710748&w=2 > > So maximum reuse is done for the board files for zoom3 and sdp3630 > > V1: Review comments incorporated: > http://marc.info/?l=linux-omap&m=125632676504364&w=2 > http://marc.info/?l=linux-omap&m=125632720804869&w=2 > http://marc.info/?l=linux-omap&m=125633994320138&w=2 > > V2: Review comments by Nishanth Menon > http://marc.info/?l=linux-omap&m=125728617825678&w=2 > http://marc.info/?l=linux-omap&m=125728665226332&w=2 > http://marc.info/?l=linux-omap&m=125728729027309&w=2 > http://marc.info/?l=linux-omap&m=125728749327603&w=2 > Vikram, I'm afraid current linux-omap master + these patches does not boot on my 3630SDP. The bootargs used were: mem=256M console=ttyS0,115200n8 noinitrd root=/dev/nfs rw nfsroot=172.24.162.66:/vol/vol2/swcoe_omapsw_linux1/anand/target,nolock,tcp ip=172.24.190.229:172.24.162.66:172.24.188.1:255.255.252.0:myomap::off The image hangs after "Uncompressing kernel...... done, booting the kernel." - Anand > Vikram Pandita (8): > omap: 3630: update is_chip variable > omap: DEBUG_LL: allow no omap uart configuration > omap: zoom2: split board file for reuse > omap: zoom2: update defconfig > omap: zoom3: introduce zoom3 board support > omap: zoom3: defconfig creation > omap: 3630sdp: introduce 3630 sdp board support > omap: 3630sdp: defconfig creation > > arch/arm/configs/omap_3630sdp_defconfig | 1606 ++++++++++++++++++++ > arch/arm/configs/omap_zoom2_defconfig | 231 ++-- > arch/arm/configs/omap_zoom3_defconfig | 1605 +++++++++++++++++++ > arch/arm/mach-omap2/Kconfig | 8 + > arch/arm/mach-omap2/Makefile | 8 + > arch/arm/mach-omap2/board-3630sdp.c | 96 ++ > arch/arm/mach-omap2/board-zoom-peripherals.c | 403 +++++ > arch/arm/mach-omap2/board-zoom2.c | 261 +--- > arch/arm/mach-omap2/board-zoom3.c | 59 + > arch/arm/mach-omap2/id.c | 2 + > arch/arm/mach-omap2/sdram-hynix-h8mbx00u0mer-0em.h | 52 + > arch/arm/plat-omap/Kconfig | 3 + > arch/arm/plat-omap/include/plat/cpu.h | 7 +- > arch/arm/plat-omap/include/plat/uncompress.h | 4 +- > 14 files changed, 4005 insertions(+), 340 deletions(-) > create mode 100644 arch/arm/configs/omap_3630sdp_defconfig > create mode 100644 arch/arm/configs/omap_zoom3_defconfig > create mode 100755 arch/arm/mach-omap2/board-3630sdp.c > create mode 100644 arch/arm/mach-omap2/board-zoom-peripherals.c > create mode 100644 arch/arm/mach-omap2/board-zoom3.c > create mode 100644 arch/arm/mach-omap2/sdram-hynix-h8mbx00u0mer-0em.h > > -- > To unsubscribe from this list: send the line "unsubscribe > linux-omap" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html > > ^ permalink raw reply [flat|nested] 16+ messages in thread
* RE: [PATCH v2 0/8] introduce 3630 boards 2009-11-10 22:47 [PATCH v2 0/8] introduce 3630 boards Vikram Pandita 2009-11-10 22:47 ` [PATCH v2 1/8] omap: 3630: update is_chip variable Vikram Pandita 2009-11-11 15:15 ` [PATCH v2 0/8] introduce 3630 boards Gadiyar, Anand @ 2009-11-11 15:19 ` Gadiyar, Anand 2009-11-11 15:28 ` Pandita, Vikram 2 siblings, 1 reply; 16+ messages in thread From: Gadiyar, Anand @ 2009-11-11 15:19 UTC (permalink / raw) To: Pandita, Vikram, linux-omap@vger.kernel.org > Vikram, > > I'm afraid current linux-omap master + these patches does not boot > on my 3630SDP. > > The bootargs used were: > mem=256M console=ttyS0,115200n8 noinitrd root=/dev/nfs rw > nfsroot=172.24.162.66:/vol/vol2/swcoe_omapsw_linux1/anand/targ > et,nolock,tcp > ip=172.24.190.229:172.24.162.66:172.24.188.1:255.255.252.0:myomap::off > > The image hangs after "Uncompressing kernel...... done, > booting the kernel." > And I just remembered we now need to patch kernel/printk.c to see low-level printks. And here's what I get: <6>Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <7>PM: Adding info for platform:serial8250 <7>PM: Adding info for No Bus:ttyS0 <7>PM: Adding info for No Bus:ttyS1 <7>PM: Adding info for No Bus:ttyS2 <7>PM: Adding info for No Bus:ttyS3 <7>PM: Removing info for No Bus:ttyS0 <1>Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa06a000 <0>Internal error: : 1028 [#1] <0>last sysfs file: <d>Modules linked in: CPU: 0 Not tainted (2.6.32-rc6-06432-ge7e7a61-dirty #13) PC is at mem_serial_in+0xc/0x14 LR is at serial8250_config_port+0x86c/0xb1c pc : [<c018c82c>] lr : [<c018e184>] psr: 00000093 sp : cf823d80 ip : c018c834 fp : 00000003 r10: 00000003 r9 : 00000001 r8 : 20000013 r7 : c03b3650 r6 : 00000060 r5 : 00000700 r4 : 00000700 r3 : 00000002 r2 : fa06a000 r1 : 00000000 r0 : c03b3650 Flags: nzcv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel Control: 10c5387d Table: 80004019 DAC: 00000017 <0>Process swapper (pid: 1, stack limit = 0xcf8222e8) <0>Stack: (0xcf823d80 to 0xcf824000) <0>3d80: c03b3650 fffffffe 10000000 02dc6c00 00000000 00000002 c03b3650 4806a000 <0>3da0: cf872000 c0377dc0 c039b1c4 c018a444 cf8dd488 cf8ab548 cf8ab560 c00e3400 <0>3dc0: cf8ab548 cf87202c cf8ac0c0 c039b300 cf8a9308 c039b300 cf8aed80 c01639e4 <0>3de0: cf8a9324 c0163984 cf872000 c0164648 cf8a9300 c03b3650 00000000 c0281a70 <0>3e00: 00000000 c03b3650 cf872000 02dc6c00 00000000 00000002 00000002 4806a000 <0>3e20: c03b3650 c0377dc0 cf823e78 c018f8f0 00000000 c037813c 00000000 4806a000 <0>3e40: c0377e10 c0377e18 00000000 10000000 fa06a000 c027f2ec cf847a80 cf8a90c0 <0>3e60: cf823e9c 00000001 cf872174 ffffffff cf823eac c0377e18 00000000 fa06a000 <0>3e80: 00000000 00000000 00000048 00000080 02dc6c00 00000000 00020200 00000000 <0>3ea0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 <0>3ec0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 10000000 <0>3ee0: 00000000 00000000 00000000 00000000 00000000 00000000 4806a000 c0377e18 <0>3f00: 00000000 c0377dc0 00000000 c0377e18 c0377e18 c039b2b0 cf8f6dc0 c039b4f8 <0>3f20: 00000000 00000000 00000000 c0193ab8 c0377e18 c0192cb4 c0377e18 c0377e4c <0>3f40: c039b2b0 cf8f6dc0 c039b4f8 c0192dc0 00000000 c0192d60 c039b2b0 c0192588 <0>3f60: cf803af8 cf8457f0 c03b3970 c039b2b0 c039b2b0 c0191ee8 c0304289 c0304289 <0>3f80: 00000001 c03b3970 00000005 c039b2b0 00000000 00000000 00000000 c0193090 <0>3fa0: c03b3970 00000005 cf8dd488 00000000 00000000 c00181e0 c0022dd4 00000000 <0>3fc0: c00180f0 c0028334 00000031 00000000 00000000 00000192 00000000 c0022dd4 <0>3fe0: 00000000 00000000 00000000 c0008578 00000000 c0029dbc 00000000 00000000 [<c018c82c>] (mem_serial_in+0xc/0x14) from [<c018e184>] (serial8250_config_port+0x86c/0xb1c) [<c018e184>] (serial8250_config_port+0x86c/0xb1c) from [<c018a444>] (uart_add_one_port+0xf4/0x2f0) [<c018a444>] (uart_add_one_port+0xf4/0x2f0) from [<c018f8f0>] (serial8250_register_port+0x1bc/0x1ec) [<c018f8f0>] (serial8250_register_port+0x1bc/0x1ec) from [<c027f2ec>] (serial8250_probe+0xb4/0x130) [<c027f2ec>] (serial8250_probe+0xb4/0x130) from [<c0193ab8>] (platform_drv_probe+0x18/0x1c) [<c0193ab8>] (platform_drv_probe+0x18/0x1c) from [<c0192cb4>] (driver_probe_device+0xa0/0x14c) [<c0192cb4>] (driver_probe_device+0xa0/0x14c) from [<c0192dc0>] (__driver_attach+0x60/0x84) [<c0192dc0>] (__driver_attach+0x60/0x84) from [<c0192588>] (bus_for_each_dev+0x44/0x74) [<c0192588>] (bus_for_each_dev+0x44/0x74) from [<c0191ee8>] (bus_add_driver+0x9c/0x220) [<c0191ee8>] (bus_add_driver+0x9c/0x220) from [<c0193090>] (driver_register+0xa8/0x130) [<c0193090>] (driver_register+0xa8/0x130) from [<c00181e0>] (serial8250_init+0xf0/0x140) [<c00181e0>] (serial8250_init+0xf0/0x140) from [<c0028334>] (do_one_initcall+0x5c/0x1b4) [<c0028334>] (do_one_initcall+0x5c/0x1b4) from [<c0008578>] (kernel_init+0x90/0x10c) [<c0008578>] (kernel_init+0x90/0x10c) from [<c0029dbc>] (kernel_thread_exit+0x0/0x8) <0>Code: e8bd8010 e5d03021 e5902004 e1a01311 (e7d20001) <4>---[ end trace 04a098cdbfa0583b ]--- <0>Kernel panic - not syncing: Attempted to kill init! ^ permalink raw reply [flat|nested] 16+ messages in thread
* RE: [PATCH v2 0/8] introduce 3630 boards 2009-11-11 15:19 ` Gadiyar, Anand @ 2009-11-11 15:28 ` Pandita, Vikram 2009-11-11 15:32 ` Gadiyar, Anand 0 siblings, 1 reply; 16+ messages in thread From: Pandita, Vikram @ 2009-11-11 15:28 UTC (permalink / raw) To: Gadiyar, Anand, linux-omap@vger.kernel.org >-----Original Message----- >From: Gadiyar, Anand >Sent: Wednesday, November 11, 2009 9:19 AM >To: Pandita, Vikram; linux-omap@vger.kernel.org >Subject: RE: [PATCH v2 0/8] introduce 3630 boards > >> Vikram, >> >> I'm afraid current linux-omap master + these patches does not boot >> on my 3630SDP. Yes you are right because its missing one patch for the 8250 driver. Refer: git://dev.omapzoom.org/pub/scm/vikram/omap3.git zoom3 Patch: HACK: 8250: fix RX fifo access for 3630 I don't have a good implementation for this patch yet and hence I have kept it in my tree as a hack patch for now. Once the board files are upstreamed, I plan to look into this 8250 patch. 8250 maintainer is not there (alan cox). Also the omap-serial patch is being worked in parallel, and does not have this crash issue. So there are variables and reasons not to post that patch yet. >> >> The bootargs used were: >> mem=256M console=ttyS0,115200n8 noinitrd root=/dev/nfs rw >> nfsroot=172.24.162.66:/vol/vol2/swcoe_omapsw_linux1/anand/targ >> et,nolock,tcp >> ip=172.24.190.229:172.24.162.66:172.24.188.1:255.255.252.0:myomap::off >> ^ permalink raw reply [flat|nested] 16+ messages in thread
* RE: [PATCH v2 0/8] introduce 3630 boards 2009-11-11 15:28 ` Pandita, Vikram @ 2009-11-11 15:32 ` Gadiyar, Anand 0 siblings, 0 replies; 16+ messages in thread From: Gadiyar, Anand @ 2009-11-11 15:32 UTC (permalink / raw) To: Pandita, Vikram, linux-omap@vger.kernel.org > >> > >> I'm afraid current linux-omap master + these patches does not boot > >> on my 3630SDP. > > Yes you are right because its missing one patch for the 8250 driver. > > Refer: > git://dev.omapzoom.org/pub/scm/vikram/omap3.git zoom3 > > Patch: HACK: 8250: fix RX fifo access for 3630 > > I don't have a good implementation for this patch yet and > hence I have kept it in my tree as a hack patch for now. > > Once the board files are upstreamed, I plan to look into this 8250 patch. > 8250 maintainer is not there (alan cox). > Also the omap-serial patch is being worked in parallel, and does not have this crash issue. > > So there are variables and reasons not to post that patch yet. > Works great with this patch. Thanks. - Anand ^ permalink raw reply [flat|nested] 16+ messages in thread
end of thread, other threads:[~2009-11-11 15:32 UTC | newest] Thread overview: 16+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2009-11-10 22:47 [PATCH v2 0/8] introduce 3630 boards Vikram Pandita 2009-11-10 22:47 ` [PATCH v2 1/8] omap: 3630: update is_chip variable Vikram Pandita 2009-11-10 22:47 ` [PATCH v2 2/8] omap: introduce OMAP_LL_DEBUG_NONE DEBUG_LL config Vikram Pandita 2009-11-10 22:47 ` [PATCH v2 3/8] omap: zoom2: split board file for software reuse Vikram Pandita 2009-11-10 22:47 ` [PATCH v2 4/8] omap: zoom2: update defconfig for LL_DEBUG_NONE Vikram Pandita 2009-11-10 22:47 ` [PATCH v2 5/8] omap: zoom3: introduce zoom3 board support Vikram Pandita 2009-11-10 22:47 ` [PATCH v2 6/8] omap: zoom3: defconfig creation Vikram Pandita 2009-11-10 22:47 ` [PATCH v2 7/8] omap: 3630sdp: introduce 3630 sdp board support Vikram Pandita 2009-11-10 22:47 ` [PATCH v2 8/8] omap: 3630sdp: defconfig creation Vikram Pandita 2009-11-11 1:24 ` [PATCH v2 3/8] omap: zoom2: split board file for software reuse Tony Lindgren 2009-11-11 1:32 ` [APPLIED] [PATCH v2 2/8] omap: introduce OMAP_LL_DEBUG_NONE DEBUG_LL config Tony Lindgren 2009-11-11 1:27 ` [APPLIED] [PATCH v2 1/8] omap: 3630: update is_chip variable Tony Lindgren 2009-11-11 15:15 ` [PATCH v2 0/8] introduce 3630 boards Gadiyar, Anand 2009-11-11 15:19 ` Gadiyar, Anand 2009-11-11 15:28 ` Pandita, Vikram 2009-11-11 15:32 ` Gadiyar, Anand
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox