From: Tony Lindgren <tony@atomide.com>
To: linux-arm-kernel@lists.infradead.org
Cc: linux-omap@vger.kernel.org, Sanjeev Premi <premi@ti.com>
Subject: [PATCH 02/23] omap3evm: Add mux settings for keypad
Date: Wed, 17 Feb 2010 17:31:53 -0800 [thread overview]
Message-ID: <20100218013153.32075.57522.stgit@baageli.muru.com> (raw)
In-Reply-To: <20100218013012.32075.43788.stgit@baageli.muru.com>
From: Sanjeev Premi <premi@ti.com>
This patch sets SYS_NIRQ for keypad input. It also
sets the same as a wakeup event from OFF mode.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-omap3evm.c | 4 ++++
1 files changed, 4 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index 45227f3..3b473cf 100644
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -647,6 +647,10 @@ static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
+ OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP |
+ OMAP_PIN_OFF_INPUT_PULLUP |
+ OMAP_PIN_OFF_WAKEUPENABLE),
+
{ .reg_offset = OMAP_MUX_TERMINATOR },
};
#else
next prev parent reply other threads:[~2010-02-18 1:31 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-02-18 1:31 [PATCH 00/23] Series short description Tony Lindgren
2010-02-18 1:31 ` [PATCH 01/23] omap: zoom3: enable ehci support Tony Lindgren
2010-02-18 1:31 ` Tony Lindgren [this message]
2010-02-18 1:31 ` [PATCH 03/23] omap3evm: Fixes after moving to matrix_keypad Tony Lindgren
2010-02-18 1:31 ` [PATCH 04/23] omap3evm: Configure GPIO175 for touchscreen PEN_IRQ Tony Lindgren
2010-02-18 1:32 ` [PATCH 05/23] OMAP: pandora: add DSS2 support and related regulators Tony Lindgren
2010-02-18 1:32 ` [PATCH 06/23] omap3: pandora: update regulator setup Tony Lindgren
2010-02-18 1:32 ` [PATCH 07/23] omap3: pandora: update defconfig Tony Lindgren
2010-02-18 1:32 ` [PATCH 08/23] omap3: Add platform data for the twl4030_codec MFD on IGEP v2 Tony Lindgren
2010-02-18 1:32 ` [PATCH 09/23] omap3: Fix typo on IGEP v2 board Tony Lindgren
2010-02-18 1:32 ` [PATCH 10/23] omap3: Add platform init code for EHCI driver on IGEP v2 Tony Lindgren
2010-02-18 1:32 ` [PATCH 11/23] omap3: Enable DSS2 for IGEP v2 board Tony Lindgren
2010-02-18 1:32 ` [PATCH 12/23] omap3: Add support for flash on " Tony Lindgren
2010-02-18 1:32 ` [PATCH 13/23] ARM: OMAP3: SDRC: add timing data for Numonyx M65KxxxxAM Tony Lindgren
2010-02-18 1:32 ` [PATCH 14/23] omap3: Use timing data for omap2_init_common_hw on IGEP v2 Tony Lindgren
2010-02-18 1:32 ` [PATCH 15/23] omap3: Update defconfig for IGEP v2 to allow new drivers andfeatures Tony Lindgren
2010-02-18 1:32 ` [PATCH 16/23] IGEPv2: Added WIFI support Tony Lindgren
2010-02-18 1:32 ` [PATCH 17/23] IGEPv2: Use Red Led1 as Heartbeat if configured Tony Lindgren
2010-02-18 1:32 ` [PATCH 18/23] AM3517: Enable basic I2C Support Tony Lindgren
2010-02-18 1:32 ` [PATCH 19/23] AM3517: Enable RTC driver support for AM3517EVM Tony Lindgren
2010-02-18 1:32 ` [PATCH 20/23] AM3517: Enable I2C-GPIO Expander " Tony Lindgren
2010-02-18 1:32 ` [PATCH 21/23] Add minimal support for DevKit8000 Tony Lindgren
2010-02-18 1:32 ` [PATCH 22/23] Add devkit8000_defconfig Tony Lindgren
2010-02-18 1:32 ` [PATCH 23/23] OMAP3EVM: PM: Update defconfig Tony Lindgren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20100218013153.32075.57522.stgit@baageli.muru.com \
--to=tony@atomide.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-omap@vger.kernel.org \
--cc=premi@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox