* [PATCH v2] board-n8x0: add USB initialization
@ 2010-03-01 22:13 Francisco Alecrim
2010-03-02 22:05 ` Tony Lindgren
0 siblings, 1 reply; 2+ messages in thread
From: Francisco Alecrim @ 2010-03-01 22:13 UTC (permalink / raw)
To: linux-omap; +Cc: Francisco Alecrim, Kalle Valo, Tony Lindgren
From: Francisco Alecrim <francisco.alecrim@openbossa.org>
Based on Kalle's and Tony's patches. Some variables re-organized and
unused code remove(68499cc5716bbeca16ca8c83ec6e9f04b8dbfacb).
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Francisco Alecrim <francisco.alecrim@openbossa.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-n8x0.c | 92 ++++++++++++++++++++++++++++++++++
arch/arm/mach-omap2/clock2420_data.c | 1 +
include/linux/usb/musb.h | 4 ++
3 files changed, 97 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-n8x0.c b/arch/arm/mach-omap2/board-n8x0.c
index ee548dd..79d659a 100644
--- a/arch/arm/mach-omap2/board-n8x0.c
+++ b/arch/arm/mach-omap2/board-n8x0.c
@@ -32,6 +32,97 @@
#include <plat/serial.h>
#include <plat/cbus.h>
+#if defined(CONFIG_USB_TUSB6010) || \
+ defined(CONFIG_USB_TUSB6010_MODULE)
+/*
+ * Enable or disable power to TUSB6010. When enabling, turn on 3.3 V and
+ * 1.5 V voltage regulators of PM companion chip. Companion chip will then
+ * provide then PGOOD signal to TUSB6010 which will release it from reset.
+ */
+static int tusb_set_power(int state)
+{
+ int i, retval = 0;
+
+ if (state) {
+ gpio_set_value(TUSB6010_GPIO_ENABLE, 1);
+ msleep(1);
+
+ /* Wait until TUSB6010 pulls INT pin down */
+ i = 100;
+ while (i && gpio_get_value(TUSB6010_GPIO_INT)) {
+ msleep(1);
+ i--;
+ }
+
+ if (!i) {
+ printk(KERN_ERR "tusb: powerup failed\n");
+ retval = -ENODEV;
+ }
+ } else {
+ gpio_set_value(TUSB6010_GPIO_ENABLE, 0);
+ msleep(10);
+ }
+
+ return retval;
+}
+
+static struct musb_hdrc_config musb_config = {
+ .multipoint = 1,
+ .dyn_fifo = 1,
+ .num_eps = 16,
+ .ram_bits = 12,
+};
+
+static struct musb_hdrc_platform_data tusb_data = {
+#if defined(CONFIG_USB_MUSB_OTG)
+ .mode = MUSB_OTG,
+#elif defined(CONFIG_USB_MUSB_PERIPHERAL)
+ .mode = MUSB_PERIPHERAL,
+#else /* defined(CONFIG_USB_MUSB_HOST) */
+ .mode = MUSB_HOST,
+#endif
+ .set_power = tusb_set_power,
+ .min_power = 25, /* x2 = 50 mA drawn from VBUS as peripheral */
+ .power = 100, /* Max 100 mA VBUS for host mode */
+ .config = &musb_config,
+};
+
+static void __init n8x0_usb_init(void)
+{
+ int ret = 0;
+ static char announce[] __initdata = KERN_INFO "TUSB 6010\n";
+
+ /* PM companion chip power control pin */
+ ret = gpio_request(TUSB6010_GPIO_ENABLE, "TUSB6010 enable");
+ if (ret != 0) {
+ printk(KERN_ERR "Could not get TUSB power GPIO%i\n",
+ TUSB6010_GPIO_ENABLE);
+ return;
+ }
+ gpio_direction_output(TUSB6010_GPIO_ENABLE, 0);
+
+ tusb_set_power(0);
+
+ ret = tusb6010_setup_interface(&tusb_data, TUSB6010_REFCLK_19, 2,
+ TUSB6010_ASYNC_CS, TUSB6010_SYNC_CS,
+ TUSB6010_GPIO_INT, 0x3f);
+ if (ret != 0)
+ goto err;
+
+ printk(announce);
+
+ return;
+
+err:
+ gpio_free(TUSB6010_GPIO_ENABLE);
+}
+#else
+
+static void __init n8x0_usb_init(void) {}
+
+#endif /*CONFIG_USB_TUSB6010 */
+
+
static struct omap2_mcspi_device_config p54spi_mcspi_config = {
.turbo_mode = 0,
.single_channel = 1,
@@ -148,6 +239,7 @@ static void __init n8x0_init_machine(void)
omap_serial_init();
n8x0_onenand_init();
+ n8x0_usb_init();
}
MACHINE_START(NOKIA_N800, "Nokia N800")
diff --git a/arch/arm/mach-omap2/clock2420_data.c b/arch/arm/mach-omap2/clock2420_data.c
index f12af95..d932b14 100644
--- a/arch/arm/mach-omap2/clock2420_data.c
+++ b/arch/arm/mach-omap2/clock2420_data.c
@@ -1841,6 +1841,7 @@ static struct omap_clk omap2420_clks[] = {
CLK(NULL, "aes_ick", &aes_ick, CK_242X),
CLK(NULL, "pka_ick", &pka_ick, CK_242X),
CLK(NULL, "usb_fck", &usb_fck, CK_242X),
+ CLK("musb_hdrc", "fck", &osc_ck, CK_242X),
};
/*
diff --git a/include/linux/usb/musb.h b/include/linux/usb/musb.h
index 3fdeef5..c281ce0 100644
--- a/include/linux/usb/musb.h
+++ b/include/linux/usb/musb.h
@@ -98,6 +98,10 @@ struct musb_hdrc_platform_data {
#define TUSB6010_OSCCLK_60 16667 /* psec/clk @ 60.0 MHz */
#define TUSB6010_REFCLK_24 41667 /* psec/clk @ 24.0 MHz XI */
#define TUSB6010_REFCLK_19 52083 /* psec/clk @ 19.2 MHz CLKIN */
+#define TUSB6010_ASYNC_CS 1
+#define TUSB6010_SYNC_CS 4
+#define TUSB6010_GPIO_INT 58
+#define TUSB6010_GPIO_ENABLE 0
#ifdef CONFIG_ARCH_OMAP2
--
1.6.3.3
^ permalink raw reply related [flat|nested] 2+ messages in thread
* Re: [PATCH v2] board-n8x0: add USB initialization
2010-03-01 22:13 [PATCH v2] board-n8x0: add USB initialization Francisco Alecrim
@ 2010-03-02 22:05 ` Tony Lindgren
0 siblings, 0 replies; 2+ messages in thread
From: Tony Lindgren @ 2010-03-02 22:05 UTC (permalink / raw)
To: Francisco Alecrim; +Cc: linux-omap, Francisco Alecrim, Kalle Valo
* Francisco Alecrim <alecrim@gmail.com> [100301 14:12]:
> From: Francisco Alecrim <francisco.alecrim@openbossa.org>
>
> Based on Kalle's and Tony's patches. Some variables re-organized and
> unused code remove(68499cc5716bbeca16ca8c83ec6e9f04b8dbfacb).
Looks like this needs to be refreshed against what's now in mainline.
Tony
> Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
> Signed-off-by: Francisco Alecrim <francisco.alecrim@openbossa.org>
> Signed-off-by: Tony Lindgren <tony@atomide.com>
> ---
> arch/arm/mach-omap2/board-n8x0.c | 92 ++++++++++++++++++++++++++++++++++
> arch/arm/mach-omap2/clock2420_data.c | 1 +
> include/linux/usb/musb.h | 4 ++
> 3 files changed, 97 insertions(+), 0 deletions(-)
>
> diff --git a/arch/arm/mach-omap2/board-n8x0.c b/arch/arm/mach-omap2/board-n8x0.c
> index ee548dd..79d659a 100644
> --- a/arch/arm/mach-omap2/board-n8x0.c
> +++ b/arch/arm/mach-omap2/board-n8x0.c
> @@ -32,6 +32,97 @@
> #include <plat/serial.h>
> #include <plat/cbus.h>
>
> +#if defined(CONFIG_USB_TUSB6010) || \
> + defined(CONFIG_USB_TUSB6010_MODULE)
> +/*
> + * Enable or disable power to TUSB6010. When enabling, turn on 3.3 V and
> + * 1.5 V voltage regulators of PM companion chip. Companion chip will then
> + * provide then PGOOD signal to TUSB6010 which will release it from reset.
> + */
> +static int tusb_set_power(int state)
> +{
> + int i, retval = 0;
> +
> + if (state) {
> + gpio_set_value(TUSB6010_GPIO_ENABLE, 1);
> + msleep(1);
> +
> + /* Wait until TUSB6010 pulls INT pin down */
> + i = 100;
> + while (i && gpio_get_value(TUSB6010_GPIO_INT)) {
> + msleep(1);
> + i--;
> + }
> +
> + if (!i) {
> + printk(KERN_ERR "tusb: powerup failed\n");
> + retval = -ENODEV;
> + }
> + } else {
> + gpio_set_value(TUSB6010_GPIO_ENABLE, 0);
> + msleep(10);
> + }
> +
> + return retval;
> +}
> +
> +static struct musb_hdrc_config musb_config = {
> + .multipoint = 1,
> + .dyn_fifo = 1,
> + .num_eps = 16,
> + .ram_bits = 12,
> +};
> +
> +static struct musb_hdrc_platform_data tusb_data = {
> +#if defined(CONFIG_USB_MUSB_OTG)
> + .mode = MUSB_OTG,
> +#elif defined(CONFIG_USB_MUSB_PERIPHERAL)
> + .mode = MUSB_PERIPHERAL,
> +#else /* defined(CONFIG_USB_MUSB_HOST) */
> + .mode = MUSB_HOST,
> +#endif
> + .set_power = tusb_set_power,
> + .min_power = 25, /* x2 = 50 mA drawn from VBUS as peripheral */
> + .power = 100, /* Max 100 mA VBUS for host mode */
> + .config = &musb_config,
> +};
> +
> +static void __init n8x0_usb_init(void)
> +{
> + int ret = 0;
> + static char announce[] __initdata = KERN_INFO "TUSB 6010\n";
> +
> + /* PM companion chip power control pin */
> + ret = gpio_request(TUSB6010_GPIO_ENABLE, "TUSB6010 enable");
> + if (ret != 0) {
> + printk(KERN_ERR "Could not get TUSB power GPIO%i\n",
> + TUSB6010_GPIO_ENABLE);
> + return;
> + }
> + gpio_direction_output(TUSB6010_GPIO_ENABLE, 0);
> +
> + tusb_set_power(0);
> +
> + ret = tusb6010_setup_interface(&tusb_data, TUSB6010_REFCLK_19, 2,
> + TUSB6010_ASYNC_CS, TUSB6010_SYNC_CS,
> + TUSB6010_GPIO_INT, 0x3f);
> + if (ret != 0)
> + goto err;
> +
> + printk(announce);
> +
> + return;
> +
> +err:
> + gpio_free(TUSB6010_GPIO_ENABLE);
> +}
> +#else
> +
> +static void __init n8x0_usb_init(void) {}
> +
> +#endif /*CONFIG_USB_TUSB6010 */
> +
> +
> static struct omap2_mcspi_device_config p54spi_mcspi_config = {
> .turbo_mode = 0,
> .single_channel = 1,
> @@ -148,6 +239,7 @@ static void __init n8x0_init_machine(void)
>
> omap_serial_init();
> n8x0_onenand_init();
> + n8x0_usb_init();
> }
>
> MACHINE_START(NOKIA_N800, "Nokia N800")
> diff --git a/arch/arm/mach-omap2/clock2420_data.c b/arch/arm/mach-omap2/clock2420_data.c
> index f12af95..d932b14 100644
> --- a/arch/arm/mach-omap2/clock2420_data.c
> +++ b/arch/arm/mach-omap2/clock2420_data.c
> @@ -1841,6 +1841,7 @@ static struct omap_clk omap2420_clks[] = {
> CLK(NULL, "aes_ick", &aes_ick, CK_242X),
> CLK(NULL, "pka_ick", &pka_ick, CK_242X),
> CLK(NULL, "usb_fck", &usb_fck, CK_242X),
> + CLK("musb_hdrc", "fck", &osc_ck, CK_242X),
> };
>
> /*
> diff --git a/include/linux/usb/musb.h b/include/linux/usb/musb.h
> index 3fdeef5..c281ce0 100644
> --- a/include/linux/usb/musb.h
> +++ b/include/linux/usb/musb.h
> @@ -98,6 +98,10 @@ struct musb_hdrc_platform_data {
> #define TUSB6010_OSCCLK_60 16667 /* psec/clk @ 60.0 MHz */
> #define TUSB6010_REFCLK_24 41667 /* psec/clk @ 24.0 MHz XI */
> #define TUSB6010_REFCLK_19 52083 /* psec/clk @ 19.2 MHz CLKIN */
> +#define TUSB6010_ASYNC_CS 1
> +#define TUSB6010_SYNC_CS 4
> +#define TUSB6010_GPIO_INT 58
> +#define TUSB6010_GPIO_ENABLE 0
>
> #ifdef CONFIG_ARCH_OMAP2
>
> --
> 1.6.3.3
>
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2010-03-02 22:03 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2010-03-01 22:13 [PATCH v2] board-n8x0: add USB initialization Francisco Alecrim
2010-03-02 22:05 ` Tony Lindgren
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox