LCD on Zoom2 dev board with DSS

LCD on Zoom2 dev board with DSS

[Yanick Saugy]

Hi all, 

I'm working on a zoom2 dev board (omap34x-II MDP). There is my actual config :

I've built kernel 2.6.35 from git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6.git
and then applied the following patchs :
[PATCH 1/2 V7] OMAP: ZOOM2/3&SDP3630: Add display board file for zoom boards <http://marc.info/?l=linux-omap&m=127445506720934&w=2>
[PATCH 2/2 V7] OMAP: ZOOM2/3&SDP3630: Add display board file for zoom boards <http://marc.info/?l=linux-omap&m=127445522921326&w=2>
[PATCH V6] OMAP: DSS: Add NEC NL8048HL11-01B display panel <http://marc.info/?l=linux-omap&m=127445535621669&w=2>

Finally I've enabled DSS and lcd NEC_NL8048HL11 in kernel config file.

At this time the kernel boots well, and my LCD backlight turns on but I can't see TUX while booting, and I can't draw anything after logging in.
I've checked, the framebuffer device is present and configured with size of 800x480.

I've played with sys filesystem like on this wiki, but nothing happened:
<http://www.omappedia.org/wiki/Bootargs_for_enabling_display>

To enable DSS at boot time, I passed following boot options:
vram=10M omapdss.def_disp=lcd


Perhaps I've missed something?

Thank you in advance.

---
Yanick

Re: LCD on Zoom2 dev board with DSS

[Felipe Balbi]

Hi,

On Mon, Sep 13, 2010 at 07:43:27AM -0500, Yanick Saugy wrote:
>Finally I've enabled DSS and lcd NEC_NL8048HL11 in kernel config file.
>
>At this time the kernel boots well, and my LCD backlight turns on but I
>can't see TUX while booting, and I can't draw anything after logging

to see tux you need to enable CONFIG_LOGO_LINUX_CLUT224 at least. Then
you also might want to enable the framebuffer console, just to get some
output on the screen.

-- 
balbi

Re: LCD on Zoom2 dev board with DSS

[Yanick Saugy]

Hi,

I solved my problem. It appeared the PIN which controls LCD's reset
signal (VGA_nRESET/h_GPIO_96) was not configured as a GPIO, and the
driver tries to use it as GPIO, so the logical value was 0. We had to
modify the OMAP MUX, and select this PIN (CAM_XCLKA) as an output GPIO
(OMAP_MUX_MODE4).

Be aware of changing this PIN will probably disable the camera, because
it was previously configured as a clock.

There is the patch for the LCD (diff -Naur):

--- a/arch/arm/mach-omap2/board-zoom2.c	2010-09-15 15:27:05.148399721
+0200
+++ b/arch/arm/mach-omap2/board-zoom2.c	2010-09-15 14:46:09.792900019
+0200
@@ -71,6 +71,7 @@
 
 #ifdef CONFIG_OMAP_MUX
 static struct omap_board_mux board_mux[] __initdata = {
+	OMAP3_MUX(CAM_XCLKA, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
 };
 #else



Le lundi 13 septembre 2010 à 14:43 +0200, Yanick Saugy a écrit :
> Hi all, 
> 
> I'm working on a zoom2 dev board (omap34x-II MDP). There is my actual config :
> 
> I've built kernel 2.6.35 from git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6.git
> and then applied the following patchs :
> [PATCH 1/2 V7] OMAP: ZOOM2/3&SDP3630: Add display board file for zoom boards <http://marc.info/?l=linux-omap&m=127445506720934&w=2>
> [PATCH 2/2 V7] OMAP: ZOOM2/3&SDP3630: Add display board file for zoom boards <http://marc.info/?l=linux-omap&m=127445522921326&w=2>
> [PATCH V6] OMAP: DSS: Add NEC NL8048HL11-01B display panel <http://marc.info/?l=linux-omap&m=127445535621669&w=2>
> 
> Finally I've enabled DSS and lcd NEC_NL8048HL11 in kernel config file.
> 
> At this time the kernel boots well, and my LCD backlight turns on but I can't see TUX while booting, and I can't draw anything after logging in.
> I've checked, the framebuffer device is present and configured with size of 800x480.
> 
> I've played with sys filesystem like on this wiki, but nothing happened:
> <http://www.omappedia.org/wiki/Bootargs_for_enabling_display>
> 
> To enable DSS at boot time, I passed following boot options:
> vram=10M omapdss.def_disp=lcd
> 
> 
> Perhaps I've missed something?
> 
> Thank you in advance.
> 
> ---
> Yanick
> 
> --
> To unsubscribe from this list: send the line "unsubscribe linux-omap" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html


--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: LCD on Zoom2 dev board with DSS

[Tony Lindgren]

* Yanick Saugy <yanick.saugy@heig-vd.ch> [100916 05:48]:
> Hi,
> 
> I solved my problem. It appeared the PIN which controls LCD's reset
> signal (VGA_nRESET/h_GPIO_96) was not configured as a GPIO, and the
> driver tries to use it as GPIO, so the logical value was 0. We had to
> modify the OMAP MUX, and select this PIN (CAM_XCLKA) as an output GPIO
> (OMAP_MUX_MODE4).
> 
> Be aware of changing this PIN will probably disable the camera, because
> it was previously configured as a clock.
> 
> There is the patch for the LCD (diff -Naur):
> 
> --- a/arch/arm/mach-omap2/board-zoom2.c	2010-09-15 15:27:05.148399721
> +0200
> +++ b/arch/arm/mach-omap2/board-zoom2.c	2010-09-15 14:46:09.792900019
> +0200
> @@ -71,6 +71,7 @@
>  
>  #ifdef CONFIG_OMAP_MUX
>  static struct omap_board_mux board_mux[] __initdata = {
> +	OMAP3_MUX(CAM_XCLKA, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
>  	{ .reg_offset = OMAP_MUX_TERMINATOR },
>  };
>  #else

Please repost with proper Signed-off-by. You might want to also
Cc Tomi Valkeinen.

Regards,

Tony

[PATCH] OMAP: ZOOM2: Change GPIO to enable LCD NEC NL8048HL11-01B on OMAP34x-II MDP

[Yanick Saugy]

The PIN which controls LCD's reset signal (VGA_nRESET/h_GPIO_96) was not
configured as a GPIO. We had to modify the OMAP MUX, and select this PIN
(CAM_XCLKA) as an output GPIO (OMAP_MUX_MODE4). (kernel 2.6.35)

Be aware of changing this PIN will probably disable the camera, because
it was previously configured as a camera clock.


Signed-off-by: Yanick Saugy <yanick.saugy@heig-vd.ch>

--- a/arch/arm/mach-omap2/board-zoom2.c 2010-09-15 15:27:05.148399721 +0200
+++ b/arch/arm/mach-omap2/board-zoom2.c 2010-09-15 14:46:09.792900019 +0200
@@ -71,6 +71,7 @@ static struct twl4030_platform_data zoom
 
 #ifdef CONFIG_OMAP_MUX
 static struct omap_board_mux board_mux[] __initdata = {
+   OMAP3_MUX(CAM_XCLKA, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
    { .reg_offset = OMAP_MUX_TERMINATOR },
 };
 #else
@@ -82,6 +83,7 @@ static void __init omap_zoom2_init(void)
    omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
    zoom_peripherals_init();
    zoom_debugboard_init();
+    zoom_display_init(OMAP_DSS_VENC_TYPE_COMPOSITE);
 }
 
 static void __init omap_zoom2_map_io(void)

Re: [PATCH] OMAP: ZOOM2: Change GPIO to enable LCD NEC NL8048HL11-01B on OMAP34x-II MDP

[Tony Lindgren]

* Yanick Saugy <yanick.saugy@heig-vd.ch> [100921 05:13]:
> The PIN which controls LCD's reset signal (VGA_nRESET/h_GPIO_96) was not
> configured as a GPIO. We had to modify the OMAP MUX, and select this PIN
> (CAM_XCLKA) as an output GPIO (OMAP_MUX_MODE4). (kernel 2.6.35)
> 
> Be aware of changing this PIN will probably disable the camera, because
> it was previously configured as a camera clock.
> 
> 
> Signed-off-by: Yanick Saugy <yanick.saugy@heig-vd.ch>

I'm assuming Tomi is queuing this.

Acked-by: Tony Lindgren <tony@atomide.com>

> 
> --- a/arch/arm/mach-omap2/board-zoom2.c 2010-09-15 15:27:05.148399721 +0200
> +++ b/arch/arm/mach-omap2/board-zoom2.c 2010-09-15 14:46:09.792900019 +0200
> @@ -71,6 +71,7 @@ static struct twl4030_platform_data zoom
>  
>  #ifdef CONFIG_OMAP_MUX
>  static struct omap_board_mux board_mux[] __initdata = {
> +   OMAP3_MUX(CAM_XCLKA, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
>     { .reg_offset = OMAP_MUX_TERMINATOR },
>  };
>  #else
> @@ -82,6 +83,7 @@ static void __init omap_zoom2_init(void)
>     omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
>     zoom_peripherals_init();
>     zoom_debugboard_init();
> +    zoom_display_init(OMAP_DSS_VENC_TYPE_COMPOSITE);
>  }
>  
>  static void __init omap_zoom2_map_io(void)
> 
> 
> 
> --
> To unsubscribe from this list: send the line "unsubscribe linux-omap" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH] OMAP: ZOOM2: Change GPIO to enable LCD NEC NL8048HL11-01B on OMAP34x-II MDP

[Tomi Valkeinen]

Hi,

On Tue, 2010-09-21 at 14:21 +0200, ext Yanick Saugy wrote:
> The PIN which controls LCD's reset signal (VGA_nRESET/h_GPIO_96) was not
> configured as a GPIO. We had to modify the OMAP MUX, and select this PIN
> (CAM_XCLKA) as an output GPIO (OMAP_MUX_MODE4). (kernel 2.6.35)
> 
> Be aware of changing this PIN will probably disable the camera, because
> it was previously configured as a camera clock.
> 
> 
> Signed-off-by: Yanick Saugy <yanick.saugy@heig-vd.ch>
> 
> --- a/arch/arm/mach-omap2/board-zoom2.c 2010-09-15 15:27:05.148399721 +0200
> +++ b/arch/arm/mach-omap2/board-zoom2.c 2010-09-15 14:46:09.792900019 +0200
> @@ -71,6 +71,7 @@ static struct twl4030_platform_data zoom
>  
>  #ifdef CONFIG_OMAP_MUX
>  static struct omap_board_mux board_mux[] __initdata = {
> +   OMAP3_MUX(CAM_XCLKA, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
>     { .reg_offset = OMAP_MUX_TERMINATOR },
>  };
>  #else
> @@ -82,6 +83,7 @@ static void __init omap_zoom2_init(void)
>     omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
>     zoom_peripherals_init();
>     zoom_debugboard_init();
> +    zoom_display_init(OMAP_DSS_VENC_TYPE_COMPOSITE);
>  }
>  
>  static void __init omap_zoom2_map_io(void)

How did you create this patch? It doesn't look like standard one, and
git am chokes on it. Also, it doesn't apply to the latest linux tree, so
you need to rebase.

 Tomi