From: Paul Walmsley <paul@pwsan.com>
To: linux-omap@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org
Cc: NeilBrown <neilb@suse.de>, Evgeniy Polyakov <zbr@ioremap.net>
Subject: [PATCH 8/8] W1: OMAP HDQ1W: use runtime PM
Date: Sat, 21 Jan 2012 16:59:36 -0700 [thread overview]
Message-ID: <20120121235935.17619.42743.stgit@dusk> (raw)
In-Reply-To: <20120121235333.17619.56725.stgit@dusk>
Convert the OMAP HDQ driver to use runtime PM. Compile- and boot-tested,
but not tested in actual use.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
---
drivers/w1/masters/omap_hdq.c | 78 +++++++----------------------------------
1 files changed, 13 insertions(+), 65 deletions(-)
diff --git a/drivers/w1/masters/omap_hdq.c b/drivers/w1/masters/omap_hdq.c
index 5ef385b..63e3eda 100644
--- a/drivers/w1/masters/omap_hdq.c
+++ b/drivers/w1/masters/omap_hdq.c
@@ -1,7 +1,7 @@
/*
* drivers/w1/masters/omap_hdq.c
*
- * Copyright (C) 2007 Texas Instruments, Inc.
+ * Copyright (C) 2007,2012 Texas Instruments, Inc.
*
* This file is licensed under the terms of the GNU General Public License
* version 2. This program is licensed "as is" without any warranty of any
@@ -14,9 +14,9 @@
#include <linux/interrupt.h>
#include <linux/slab.h>
#include <linux/err.h>
-#include <linux/clk.h>
#include <linux/io.h>
#include <linux/sched.h>
+#include <linux/pm_runtime.h>
#include <asm/irq.h>
#include <mach/hardware.h>
@@ -61,8 +61,6 @@ struct hdq_data {
/* lock status update */
struct mutex hdq_mutex;
int hdq_usecount;
- struct clk *hdq_ick;
- struct clk *hdq_fck;
u8 hdq_irqstatus;
/* device lock */
spinlock_t hdq_spinlock;
@@ -419,17 +417,8 @@ static int omap_hdq_get(struct hdq_data *hdq_data)
hdq_data->hdq_usecount++;
try_module_get(THIS_MODULE);
if (1 == hdq_data->hdq_usecount) {
- if (clk_enable(hdq_data->hdq_ick)) {
- dev_dbg(hdq_data->dev, "Can not enable ick\n");
- ret = -ENODEV;
- goto clk_err;
- }
- if (clk_enable(hdq_data->hdq_fck)) {
- dev_dbg(hdq_data->dev, "Can not enable fck\n");
- clk_disable(hdq_data->hdq_ick);
- ret = -ENODEV;
- goto clk_err;
- }
+
+ pm_runtime_get_sync(hdq_data->dev);
/* make sure HDQ is out of reset */
if (!(hdq_reg_in(hdq_data, OMAP_HDQ_SYSSTATUS) &
@@ -450,9 +439,6 @@ static int omap_hdq_get(struct hdq_data *hdq_data)
}
}
-clk_err:
- clk_put(hdq_data->hdq_ick);
- clk_put(hdq_data->hdq_fck);
out:
mutex_unlock(&hdq_data->hdq_mutex);
rtn:
@@ -475,10 +461,8 @@ static int omap_hdq_put(struct hdq_data *hdq_data)
} else {
hdq_data->hdq_usecount--;
module_put(THIS_MODULE);
- if (0 == hdq_data->hdq_usecount) {
- clk_disable(hdq_data->hdq_ick);
- clk_disable(hdq_data->hdq_fck);
- }
+ if (0 == hdq_data->hdq_usecount)
+ pm_runtime_put_sync(hdq_data->dev);
}
mutex_unlock(&hdq_data->hdq_mutex);
@@ -591,35 +575,11 @@ static int __devinit omap_hdq_probe(struct platform_device *pdev)
goto err_ioremap;
}
- /* get interface & functional clock objects */
- hdq_data->hdq_ick = clk_get(&pdev->dev, "ick");
- if (IS_ERR(hdq_data->hdq_ick)) {
- dev_dbg(&pdev->dev, "Can't get HDQ ick clock object\n");
- ret = PTR_ERR(hdq_data->hdq_ick);
- goto err_ick;
- }
-
- hdq_data->hdq_fck = clk_get(&pdev->dev, "fck");
- if (IS_ERR(hdq_data->hdq_fck)) {
- dev_dbg(&pdev->dev, "Can't get HDQ fck clock object\n");
- ret = PTR_ERR(hdq_data->hdq_fck);
- goto err_fck;
- }
-
hdq_data->hdq_usecount = 0;
mutex_init(&hdq_data->hdq_mutex);
- if (clk_enable(hdq_data->hdq_ick)) {
- dev_dbg(&pdev->dev, "Can not enable ick\n");
- ret = -ENODEV;
- goto err_intfclk;
- }
-
- if (clk_enable(hdq_data->hdq_fck)) {
- dev_dbg(&pdev->dev, "Can not enable fck\n");
- ret = -ENODEV;
- goto err_fnclk;
- }
+ pm_runtime_enable(&pdev->dev);
+ pm_runtime_get_sync(&pdev->dev);
rev = hdq_reg_in(hdq_data, OMAP_HDQ_REVISION);
dev_info(&pdev->dev, "OMAP HDQ Hardware Rev %c.%c. Driver in %s mode\n",
@@ -641,9 +601,7 @@ static int __devinit omap_hdq_probe(struct platform_device *pdev)
omap_hdq_break(hdq_data);
- /* don't clock the HDQ until it is needed */
- clk_disable(hdq_data->hdq_ick);
- clk_disable(hdq_data->hdq_fck);
+ pm_runtime_put_sync(&pdev->dev);
omap_w1_master.data = hdq_data;
@@ -655,20 +613,11 @@ static int __devinit omap_hdq_probe(struct platform_device *pdev)
return 0;
-err_w1:
err_irq:
- clk_disable(hdq_data->hdq_fck);
-
-err_fnclk:
- clk_disable(hdq_data->hdq_ick);
-
-err_intfclk:
- clk_put(hdq_data->hdq_fck);
-
-err_fck:
- clk_put(hdq_data->hdq_ick);
+ pm_runtime_put_sync(&pdev->dev);
+err_w1:
+ pm_runtime_disable(&pdev->dev);
-err_ick:
iounmap(hdq_data->hdq_base);
err_ioremap:
@@ -696,8 +645,7 @@ static int omap_hdq_remove(struct platform_device *pdev)
mutex_unlock(&hdq_data->hdq_mutex);
/* remove module dependency */
- clk_put(hdq_data->hdq_ick);
- clk_put(hdq_data->hdq_fck);
+ pm_runtime_disable(&pdev->dev);
free_irq(INT_24XX_HDQ_IRQ, hdq_data);
platform_set_drvdata(pdev, NULL);
iounmap(hdq_data->hdq_base);
prev parent reply other threads:[~2012-01-21 23:59 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-01-21 23:59 [PATCH 0/8] ARM: OMAP: HDQ/1-wire: update driver to use runtime PM Paul Walmsley
2012-01-21 23:59 ` [PATCH 1/8] ARM: OMAP3: clock data: add clockdomain for HDQ functional clock Paul Walmsley
2012-01-21 23:59 ` [PATCH 2/8] ARM: OMAP2+: HDQ1W: add custom reset function Paul Walmsley
2012-01-21 23:59 ` [PATCH 4/8] ARM: OMAP3: hwmod data: add HDQ/1-wire hwmod Paul Walmsley
2012-01-21 23:59 ` [PATCH 3/8] ARM: OMAP2+: hwmod data: add HDQ/1-wire hwmod shared data Paul Walmsley
2012-01-21 23:59 ` [PATCH 5/8] ARM: OMAP2xxx: hwmod data: add HDQ/1-wire hwmod Paul Walmsley
2012-01-21 23:59 ` [PATCH 6/8] ARM: OMAP4: " Paul Walmsley
2012-01-22 3:47 ` Paul Walmsley
2012-01-21 23:59 ` [PATCH 7/8] ARM: OMAP2+: HDQ1W: use omap_device Paul Walmsley
2012-01-21 23:59 ` Paul Walmsley [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20120121235935.17619.42743.stgit@dusk \
--to=paul@pwsan.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=neilb@suse.de \
--cc=zbr@ioremap.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).