receiving data from mcbsp1 in master mode

receiving data from mcbsp1 in master mode

[Andreas Kemnade]

[-- Attachment #1: Type: text/plain, Size: 496 bytes --]

Hi,

I tried a couple of times with different kernels to use mcbsp1 of dm3730
in master mode (so that it sends out clocks).
The result always is that I can send data out. but arecord gets no input. It
waits for input but does not get anything, although clocks are generated,
checked that with a scope. 

I even took a driver which works in master mode on another mcbsp and just changed
the mcbsp number.
What needs to be done to receive data from mcbsp1?

Greetings
Andreas Kemnade

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 198 bytes --]

Re: receiving data from mcbsp1 in master mode

[Peter Ujfalusi]

On 08/21/2012 08:42 AM, Andreas Kemnade wrote:
> Hi,
> 
> I tried a couple of times with different kernels to use mcbsp1 of dm3730
> in master mode (so that it sends out clocks).
> The result always is that I can send data out. but arecord gets no input. It
> waits for input but does not get anything, although clocks are generated,
> checked that with a scope. 
> 
> I even took a driver which works in master mode on another mcbsp and just changed
> the mcbsp number.
> What needs to be done to receive data from mcbsp1?

You should check the PIN mux configuration of McBSP1 FSR/CLKR pins. McBSP1 on
dm3730 have 6 pin configuration. I think the capture should work fine if you
select the FSX as FSR source, and CLKX as CLKR source.

-- 
Péter
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: receiving data from mcbsp1 in master mode

[Andreas Kemnade]

[-- Attachment #1: Type: text/plain, Size: 1706 bytes --]

Hi,

On Tue, 21 Aug 2012 16:42:19 +0300
Peter Ujfalusi <peter.ujfalusi@ti.com> wrote:

> On 08/21/2012 08:42 AM, Andreas Kemnade wrote:
> > Hi,
> > 
> > I tried a couple of times with different kernels to use mcbsp1 of dm3730
> > in master mode (so that it sends out clocks).
> > The result always is that I can send data out. but arecord gets no input. It
> > waits for input but does not get anything, although clocks are generated,
> > checked that with a scope. 
> > 
> > I even took a driver which works in master mode on another mcbsp and just changed
> > the mcbsp number.
> > What needs to be done to receive data from mcbsp1?
> 
> You should check the PIN mux configuration of McBSP1 FSR/CLKR pins. McBSP1 on
> dm3730 have 6 pin configuration. I think the capture should work fine if you
> select the FSX as FSR source, and CLKX as CLKR source.
>
if I understand the TRM correctly, according to Figure 21-26 in chapter 21.4.2.3.
if GSYNC is set, the receiver uses the signal from the sample rate generator,
so CLKX does not need to be the CLKR source.
But I tried also with the DEVCONF0 MCBSP1_CLKR bit as you proposed.
I tried
 snd_soc_dai_set_sysclk(cpu_dai, OMAP_MCBSP_CLKR_SRC_CLKX, 0,
                                     SND_SOC_CLOCK_OUT);
 snd_soc_dai_set_sysclk(cpu_dai, OMAP_MCBSP_FSR_SRC_FSX, 0,
                                     SND_SOC_CLOCK_OUT);

 That is why I send you my patch about that mux settings. But I had no success.
The CLKX as CLKR source and FSX as FSR source setting I have only seen when
mcbsp1 is used in slave mode. If you know any working code which uses mcbsp1 in
master mode then let me know.

Greetings
Andreas Kemnade

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 198 bytes --]

Re: receiving data from mcbsp1 in master mode

[Peter Ujfalusi]

On 08/22/2012 11:19 PM, Andreas Kemnade wrote:
> if I understand the TRM correctly, according to Figure 21-26 in chapter 21.4.2.3.
> if GSYNC is set, the receiver uses the signal from the sample rate generator,
> so CLKX does not need to be the CLKR source.
> But I tried also with the DEVCONF0 MCBSP1_CLKR bit as you proposed.
> I tried
>  snd_soc_dai_set_sysclk(cpu_dai, OMAP_MCBSP_CLKR_SRC_CLKX, 0,
>                                      SND_SOC_CLOCK_OUT);
>  snd_soc_dai_set_sysclk(cpu_dai, OMAP_MCBSP_FSR_SRC_FSX, 0,
>                                      SND_SOC_CLOCK_OUT);

There is an issue with the 6pin mux code, try to add this patch:
http://mailman.alsa-project.org/pipermail/alsa-devel/2012-August/054041.html

>  That is why I send you my patch about that mux settings. But I had no success.
> The CLKX as CLKR source and FSX as FSR source setting I have only seen when
> mcbsp1 is used in slave mode. If you know any working code which uses mcbsp1 in
> master mode then let me know.

No, I don't have board which uses McBSP1.

-- 
Péter
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: receiving data from mcbsp1 in master mode

[Andreas Kemnade]

[-- Attachment #1: Type: text/plain, Size: 1381 bytes --]

On Thu, 23 Aug 2012 11:47:59 +0300
Peter Ujfalusi <peter.ujfalusi@ti.com> wrote:

> On 08/22/2012 11:19 PM, Andreas Kemnade wrote:
> > if I understand the TRM correctly, according to Figure 21-26 in chapter 21.4.2.3.
> > if GSYNC is set, the receiver uses the signal from the sample rate generator,
> > so CLKX does not need to be the CLKR source.
> > But I tried also with the DEVCONF0 MCBSP1_CLKR bit as you proposed.
> > I tried
> >  snd_soc_dai_set_sysclk(cpu_dai, OMAP_MCBSP_CLKR_SRC_CLKX, 0,
> >                                      SND_SOC_CLOCK_OUT);
> >  snd_soc_dai_set_sysclk(cpu_dai, OMAP_MCBSP_FSR_SRC_FSX, 0,
> >                                      SND_SOC_CLOCK_OUT);
> 
> There is an issue with the 6pin mux code, try to add this patch:
> http://mailman.alsa-project.org/pipermail/alsa-devel/2012-August/054041.html
> 
That is exactly the patch I was talking about in the next line, see
http://marc.info/?l=linux-omap&m=134540540412165&w=2

> >  That is why I send you my patch about that mux settings. But I had no success.
     ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
> > The CLKX as CLKR source and FSX as FSR source setting I have only seen when
> > mcbsp1 is used in slave mode. If you know any working code which uses mcbsp1 in
> > master mode then let me know.
> 
> No, I don't have board which uses McBSP1.
> 
> -- 
> Péter
> 
> 

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 198 bytes --]