[PATCH 5/6] ARM: OMAP2+: clean up OMAP clock Makefile sections

Paul Walmsley
2012-09-08T00:41:47Z

Clean up the OMAP clock code sections of the Makefile to save
some lines of diff.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
---
arch/arm/mach-omap2/Makefile | 21 ++++++++-------------
1 file changed, 8 insertions(+), 13 deletions(-)

diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index e9de8d2..89e0daf 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -6,9 +6,6 @@
obj-y := id.o io.o control.o mux.o devices.o serial.o gpmc.o timer.o pm.o \
common.o gpio.o dma.o wd_timer.o display.o i2c.o hdq1w.o omap_hwmod.o

-clock-common = clock.o clock_common_data.o \
- clkt_dpll.o clkt_clksel.o
-
# INTCPS IP block support - XXX should be moved to drivers/
obj-$(CONFIG_ARCH_OMAP2) += irq.o
obj-$(CONFIG_ARCH_OMAP3) += irq.o
@@ -155,24 +152,22 @@ obj-$(CONFIG_SOC_OMAP5) += $(clockdomain-common)
obj-$(CONFIG_SOC_OMAP5) += clockdomain44xx.o

# Clock framework
-obj-$(CONFIG_ARCH_OMAP2) += $(clock-common) clock2xxx.o
-obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_sys.o
-obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_dpllcore.o
+obj-y += clock.o clock_common_data.o \
+ clkt_dpll.o clkt_clksel.o
+obj-$(CONFIG_ARCH_OMAP2) += clock2xxx.o
+obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_dpllcore.o clkt2xxx_sys.o
obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_virt_prcm_set.o
obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_apll.o clkt2xxx_osc.o
obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_dpll.o clkt_iclk.o
obj-$(CONFIG_SOC_OMAP2420) += clock2420_data.o
obj-$(CONFIG_SOC_OMAP2430) += clock2430.o clock2430_data.o
-obj-$(CONFIG_ARCH_OMAP3) += $(clock-common) clock3xxx.o
+obj-$(CONFIG_ARCH_OMAP3) += clock3xxx.o
obj-$(CONFIG_ARCH_OMAP3) += clock34xx.o clkt34xx_dpll3m2.o
-obj-$(CONFIG_ARCH_OMAP3) += clock3517.o clock36xx.o
+obj-$(CONFIG_ARCH_OMAP3) += clock3517.o clock36xx.o clkt_iclk.o
obj-$(CONFIG_ARCH_OMAP3) += dpll3xxx.o clock3xxx_data.o
-obj-$(CONFIG_ARCH_OMAP3) += clkt_iclk.o
-obj-$(CONFIG_ARCH_OMAP4) += $(clock-common) clock44xx_data.o
+obj-$(CONFIG_ARCH_OMAP4) += clock44xx_data.o
obj-$(CONFIG_ARCH_OMAP4) += dpll3xxx.o dpll44xx.o
-obj-$(CONFIG_SOC_AM33XX) += $(clock-common) dpll3xxx.o
-obj-$(CONFIG_SOC_AM33XX) += clock33xx_data.o
-obj-$(CONFIG_SOC_OMAP5) += $(clock-common)
+obj-$(CONFIG_SOC_AM33XX) += dpll3xxx.o clock33xx_data.o
obj-$(CONFIG_SOC_OMAP5) += dpll3xxx.o dpll44xx.o

# OMAP2 clock rate set data (old "OPP" data)