From: Felipe Balbi <balbi@ti.com>
To: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Felipe Balbi <balbi@ti.com>,
Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
linux-usb@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-omap@vger.kernel.org,
Kishon Vijay Abraham I <kishon@ti.com>
Subject: Re: [PATCH] usb: otg: twl4030: Change TWL4030_MODULE_* ids to TWL_MODULE_*
Date: Tue, 13 Nov 2012 11:47:22 +0200 [thread overview]
Message-ID: <20121113094722.GB10395@arwen.pp.htv.fi> (raw)
In-Reply-To: <1352799818-22363-1-git-send-email-peter.ujfalusi@ti.com>
[-- Attachment #1: Type: text/plain, Size: 5792 bytes --]
On Tue, Nov 13, 2012 at 10:43:38AM +0100, Peter Ujfalusi wrote:
> To facilitate upcoming cleanup in twl stack.
> No functional changes.
>
> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
I guess this one must go together with the rest of your series...
Acked-by: Felipe Balbi <balbi@ti.com>
> ---
> drivers/usb/otg/twl4030-usb.c | 46 ++++++++++++++++++++-----------------------
> 1 file changed, 21 insertions(+), 25 deletions(-)
>
> diff --git a/drivers/usb/otg/twl4030-usb.c b/drivers/usb/otg/twl4030-usb.c
> index f0d2e75..11b2a12 100644
> --- a/drivers/usb/otg/twl4030-usb.c
> +++ b/drivers/usb/otg/twl4030-usb.c
> @@ -123,10 +123,10 @@
> #define PHY_CLK_CTRL_STS 0xFF
> #define PHY_DPLL_CLK (1 << 0)
>
> -/* In module TWL4030_MODULE_PM_MASTER */
> +/* In module TWL_MODULE_PM_MASTER */
> #define STS_HW_CONDITIONS 0x0F
>
> -/* In module TWL4030_MODULE_PM_RECEIVER */
> +/* In module TWL_MODULE_PM_RECEIVER */
> #define VUSB_DEDICATED1 0x7D
> #define VUSB_DEDICATED2 0x7E
> #define VUSB1V5_DEV_GRP 0x71
> @@ -195,14 +195,14 @@ static int twl4030_i2c_write_u8_verify(struct twl4030_usb *twl,
> }
>
> #define twl4030_usb_write_verify(twl, address, data) \
> - twl4030_i2c_write_u8_verify(twl, TWL4030_MODULE_USB, (data), (address))
> + twl4030_i2c_write_u8_verify(twl, TWL_MODULE_USB, (data), (address))
>
> static inline int twl4030_usb_write(struct twl4030_usb *twl,
> u8 address, u8 data)
> {
> int ret = 0;
>
> - ret = twl_i2c_write_u8(TWL4030_MODULE_USB, data, address);
> + ret = twl_i2c_write_u8(TWL_MODULE_USB, data, address);
> if (ret < 0)
> dev_dbg(twl->dev,
> "TWL4030:USB:Write[0x%x] Error %d\n", address, ret);
> @@ -227,7 +227,7 @@ static inline int twl4030_readb(struct twl4030_usb *twl, u8 module, u8 address)
>
> static inline int twl4030_usb_read(struct twl4030_usb *twl, u8 address)
> {
> - return twl4030_readb(twl, TWL4030_MODULE_USB, address);
> + return twl4030_readb(twl, TWL_MODULE_USB, address);
> }
>
> /*-------------------------------------------------------------------------*/
> @@ -264,8 +264,7 @@ static enum omap_musb_vbus_id_status
> * signal is active, the OTG module is activated, and
> * its interrupt may be raised (may wake the system).
> */
> - status = twl4030_readb(twl, TWL4030_MODULE_PM_MASTER,
> - STS_HW_CONDITIONS);
> + status = twl4030_readb(twl, TWL_MODULE_PM_MASTER, STS_HW_CONDITIONS);
> if (status < 0)
> dev_err(twl->dev, "USB link status err %d\n", status);
> else if (status & (BIT(7) | BIT(2))) {
> @@ -372,8 +371,7 @@ static void twl4030_phy_power(struct twl4030_usb *twl, int on)
> * SLEEP. We work around this by clearing the bit after usv3v1
> * is re-activated. This ensures that VUSB3V1 is really active.
> */
> - twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0,
> - VUSB_DEDICATED2);
> + twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB_DEDICATED2);
> regulator_enable(twl->usb1v5);
> __twl4030_phy_power(twl, 1);
> twl4030_usb_write(twl, PHY_CLK_CTRL,
> @@ -419,50 +417,48 @@ static void twl4030_phy_resume(struct twl4030_usb *twl)
> static int twl4030_usb_ldo_init(struct twl4030_usb *twl)
> {
> /* Enable writing to power configuration registers */
> - twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER,
> - TWL4030_PM_MASTER_KEY_CFG1,
> - TWL4030_PM_MASTER_PROTECT_KEY);
> + twl_i2c_write_u8(TWL_MODULE_PM_MASTER, TWL4030_PM_MASTER_KEY_CFG1,
> + TWL4030_PM_MASTER_PROTECT_KEY);
>
> - twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER,
> - TWL4030_PM_MASTER_KEY_CFG2,
> - TWL4030_PM_MASTER_PROTECT_KEY);
> + twl_i2c_write_u8(TWL_MODULE_PM_MASTER, TWL4030_PM_MASTER_KEY_CFG2,
> + TWL4030_PM_MASTER_PROTECT_KEY);
>
> /* Keep VUSB3V1 LDO in sleep state until VBUS/ID change detected*/
> - /*twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB_DEDICATED2);*/
> + /*twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB_DEDICATED2);*/
>
> /* input to VUSB3V1 LDO is from VBAT, not VBUS */
> - twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0x14, VUSB_DEDICATED1);
> + twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0x14, VUSB_DEDICATED1);
>
> /* Initialize 3.1V regulator */
> - twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB3V1_DEV_GRP);
> + twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB3V1_DEV_GRP);
>
> twl->usb3v1 = regulator_get(twl->dev, "usb3v1");
> if (IS_ERR(twl->usb3v1))
> return -ENODEV;
>
> - twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB3V1_TYPE);
> + twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB3V1_TYPE);
>
> /* Initialize 1.5V regulator */
> - twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB1V5_DEV_GRP);
> + twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB1V5_DEV_GRP);
>
> twl->usb1v5 = regulator_get(twl->dev, "usb1v5");
> if (IS_ERR(twl->usb1v5))
> goto fail1;
>
> - twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB1V5_TYPE);
> + twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB1V5_TYPE);
>
> /* Initialize 1.8V regulator */
> - twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB1V8_DEV_GRP);
> + twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB1V8_DEV_GRP);
>
> twl->usb1v8 = regulator_get(twl->dev, "usb1v8");
> if (IS_ERR(twl->usb1v8))
> goto fail2;
>
> - twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB1V8_TYPE);
> + twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB1V8_TYPE);
>
> /* disable access to power configuration registers */
> - twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER, 0,
> - TWL4030_PM_MASTER_PROTECT_KEY);
> + twl_i2c_write_u8(TWL_MODULE_PM_MASTER, 0,
> + TWL4030_PM_MASTER_PROTECT_KEY);
>
> return 0;
>
> --
> 1.8.0
>
--
balbi
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]
next prev parent reply other threads:[~2012-11-13 9:47 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-11-13 9:43 [PATCH] usb: otg: twl4030: Change TWL4030_MODULE_* ids to TWL_MODULE_* Peter Ujfalusi
2012-11-13 9:47 ` Felipe Balbi [this message]
2012-11-13 10:28 ` Peter Ujfalusi
2012-11-13 10:37 ` Felipe Balbi
2012-11-13 10:57 ` Peter Ujfalusi
2012-11-13 11:03 ` Felipe Balbi
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20121113094722.GB10395@arwen.pp.htv.fi \
--to=balbi@ti.com \
--cc=gregkh@linuxfoundation.org \
--cc=kishon@ti.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=peter.ujfalusi@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox