* [PATCH 2/3] arm: dts: Add Siemens Draco SOM dtsi
2014-02-05 12:12 [PATCH 1/3] arm: dts: am33xx.dtsi: Add node name to rtc device node Stefan Roese
@ 2014-02-05 12:12 ` Stefan Roese
2014-02-05 12:12 ` [PATCH 3/3] arm: dts: Add Siemens am335x-dxr2-e.dts Stefan Roese
` (2 subsequent siblings)
3 siblings, 0 replies; 5+ messages in thread
From: Stefan Roese @ 2014-02-05 12:12 UTC (permalink / raw)
To: linux-arm-kernel
Cc: linux-omap, Lukas Stockmann, Benoit Cousson, Tony Lindgren
This patch adds support for the Siemens Draco SOM (System On Module) which
is used by multiple Siemens boards. Support for one is posted in this
series as well, the dxr2-e.
This SOM is based on the TI AM3352 with the following configuration:
- CPU: AM3352BZCEA30
- RAM: 128MB DDR3@303MHz
- NAND FLASH: 256MB
- RTC: disabled via hw wiring (registers not available!)
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Lukas Stockmann <lukas.stockmann@siemens.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
---
arch/arm/boot/dts/am335x-draco.dtsi | 163 ++++++++++++++++++++++++++++++++++++
1 file changed, 163 insertions(+)
create mode 100644 arch/arm/boot/dts/am335x-draco.dtsi
diff --git a/arch/arm/boot/dts/am335x-draco.dtsi b/arch/arm/boot/dts/am335x-draco.dtsi
new file mode 100644
index 0000000..88b414a
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-draco.dtsi
@@ -0,0 +1,163 @@
+/*
+ * Common support for Siemens Draco SOM (AM335x based)
+ *
+ * Copyright (C) 2013,2014 - Stefan Roese <sr@denx.de>
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/ {
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x08000000>; /* 128 MB */
+ };
+
+ am33xx_pinmux: pinmux@44e10800 {
+ i2c0_pins: pinmux_i2c0_pins {
+ pinctrl-single,pins = <
+ 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */
+ 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */
+ >;
+ };
+
+ uart0_pins: pinmux_uart0_pins {
+ pinctrl-single,pins = <
+ 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
+ 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
+ >;
+ };
+
+ nandflash_pins: nandflash_pins {
+ pinctrl-single,pins = <
+ 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */
+ 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */
+ 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */
+ 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */
+ 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */
+ 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */
+ 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */
+ 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */
+ 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */
+ 0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_30 */
+ 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */
+ 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */
+ 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */
+ 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */
+ 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */
+ >;
+ };
+ };
+
+ ocp {
+ uart0: serial@44e09000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+ status = "okay";
+ };
+
+ i2c0: i2c@44e0b000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+
+ status = "okay";
+ clock-frequency = <400000>;
+
+ eeprom: eeprom@50 {
+ compatible = "atmel,24c128";
+ reg = <0x50>;
+ pagesize = <64>;
+ };
+ };
+
+ musb: usb@47400000 {
+ status = "okay";
+
+ control@44e10000 {
+ status = "okay";
+ };
+
+ usb-phy@47401300 {
+ status = "okay";
+ };
+
+ usb-phy@47401b00 {
+ status = "okay";
+ };
+
+ usb@47401000 {
+ status = "okay";
+ };
+
+ usb@47401800 {
+ status = "okay";
+ dr_mode = "host";
+ };
+
+ dma-controller@07402000 {
+ status = "okay";
+ };
+ };
+ };
+};
+
+&timer3 {
+ status = "disabled";
+};
+
+&uart4 {
+ status = "disabled";
+};
+
+&elm {
+ status = "okay";
+};
+
+&gpmc {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&nandflash_pins>;
+
+ ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */
+
+ nand@0,0 {
+ reg = <0 0 0>; /* CS0, offset 0 */
+ nand-bus-width = <8>;
+ ti,nand-ecc-opt = "bch8";
+ gpmc,device-nand = "true";
+ gpmc,device-width = <1>;
+ gpmc,sync-clk-ps = <0>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <44>;
+ gpmc,cs-wr-off-ns = <44>;
+ gpmc,adv-on-ns = <6>;
+ gpmc,adv-rd-off-ns = <34>;
+ gpmc,adv-wr-off-ns = <44>;
+ gpmc,we-on-ns = <0>;
+ gpmc,we-off-ns = <40>;
+ gpmc,oe-on-ns = <0>;
+ gpmc,oe-off-ns = <54>;
+ gpmc,access-ns = <64>;
+ gpmc,rd-cycle-ns = <82>;
+ gpmc,wr-cycle-ns = <82>;
+ gpmc,wait-on-read = "true";
+ gpmc,wait-on-write = "true";
+ gpmc,bus-turnaround-ns = <0>;
+ gpmc,cycle2cycle-delay-ns = <0>;
+ gpmc,clk-activation-ns = <0>;
+ gpmc,wait-monitoring-ns = <0>;
+ gpmc,wr-access-ns = <40>;
+ gpmc,wr-data-mux-bus-ns = <0>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ elm_id = <&elm>;
+ };
+};
+
+/* disable the RTC node as its not accessible on the draco/dxr2 board */
+&rtc {
+ status = "disabled";
+ ti,hwmods = "disabled";
+};
--
1.8.5.3
^ permalink raw reply related [flat|nested] 5+ messages in thread* [PATCH 3/3] arm: dts: Add Siemens am335x-dxr2-e.dts
2014-02-05 12:12 [PATCH 1/3] arm: dts: am33xx.dtsi: Add node name to rtc device node Stefan Roese
2014-02-05 12:12 ` [PATCH 2/3] arm: dts: Add Siemens Draco SOM dtsi Stefan Roese
@ 2014-02-05 12:12 ` Stefan Roese
2014-02-05 18:29 ` [PATCH 1/3] arm: dts: am33xx.dtsi: Add node name to rtc device node Sergei Shtylyov
2014-02-28 22:45 ` Tony Lindgren
3 siblings, 0 replies; 5+ messages in thread
From: Stefan Roese @ 2014-02-05 12:12 UTC (permalink / raw)
To: linux-arm-kernel
Cc: linux-omap, Lukas Stockmann, Benoit Cousson, Tony Lindgren
Add support for the Siemens DXR2 board. The DXR2-E is the first one
that is pushed now. It uses the Draco SOM and therefor includes this
dtsi file for the common device nodes.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Lukas Stockmann <lukas.stockmann@siemens.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
---
arch/arm/boot/dts/am335x-dxr2-e.dts | 242 ++++++++++++++++++++++++++++++++++++
1 file changed, 242 insertions(+)
create mode 100644 arch/arm/boot/dts/am335x-dxr2-e.dts
diff --git a/arch/arm/boot/dts/am335x-dxr2-e.dts b/arch/arm/boot/dts/am335x-dxr2-e.dts
new file mode 100644
index 0000000..5fef637
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-dxr2-e.dts
@@ -0,0 +1,242 @@
+/*
+ * Support for Siemens DXR2.E board
+ *
+ * Copyright (C) 2013,2014 - Stefan Roese <sr@denx.de>
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/dts-v1/;
+
+#include "am33xx.dtsi"
+#include "am335x-draco.dtsi"
+#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Siemens DXR2.E";
+ compatible = "siemens,dxr2", "ti,am33xx";
+
+ /* ethernet alias is needed for the MAC address passing from U-Boot */
+ aliases {
+ ethernet0 = &cpsw_emac0;
+ mdio-gpio0 = &mdio0;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ button0 {
+ label = "button0";
+ gpios = <&gpio0 27 0>;
+ linux,code = <KEY_F1>; /* button0 */
+ };
+ };
+
+ am33xx_pinmux: pinmux@44e10800 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_mux_pins>;
+
+ gpio_mux_pins: gpio_mux_pins {
+ pinctrl-single,pins = <
+ 0x020 (PIN_OUTPUT | MUX_MODE4) /* GPMC_AD8, sinus inverter */
+ 0x024 (PIN_OUTPUT | MUX_MODE4) /* GPMC_AD9, sinus inverter */
+ 0x028 (PIN_INPUT | MUX_MODE4) /* GPMC_AD10, sinus inverter */
+ 0x02c (PIN_INPUT | MUX_MODE7) /* GPMC_AD11, button */
+ 0x030 (PIN_OUTPUT | MUX_MODE7) /* GPMC_AD12, UI */
+ 0x034 (PIN_OUTPUT | MUX_MODE7) /* GPMC_AD13, UI */
+ 0x038 (PIN_OUTPUT | MUX_MODE7) /* conf_gpmc_ad14, relay0 */
+ 0x03c (PIN_OUTPUT | MUX_MODE7) /* GPMC_AD15, UI */
+ 0x08c (PIN_OUTPUT | MUX_MODE7) /* GPMC_CLK, UI */
+ 0x0d4 (PIN_OUTPUT | MUX_MODE7) /* LCD_DATA13, AO_EN */
+ 0x0dc (PIN_OUTPUT | MUX_MODE7) /* LCD_DATA15, UI */
+ 0x0ec (PIN_INPUT | MUX_MODE7) /* LCD_AC_BIAS_EN, PWfail */
+ 0x0f0 (PIN_OUTPUT | MUX_MODE7) /* MMC0_DAT3, UI */
+ 0x0f4 (PIN_OUTPUT | MUX_MODE7) /* MMC0_DAT2, UI */
+ 0x0f8 (PIN_OUTPUT | MUX_MODE7) /* MMC0_DAT1, UI */
+ 0x0fc (PIN_OUTPUT | MUX_MODE7) /* MMC0_DAT0, UI */
+ 0x108 (PIN_OUTPUT | MUX_MODE7) /* MII1_COL, relay1 */
+ 0x100 (PIN_OUTPUT | MUX_MODE7) /* MMC0_CLK, UI */
+ 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* MII1_RX_DV.gpio3.4, di0 */
+ 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* MII1_TXD2.gpio0.17, di1 */
+ 0x12c (PIN_OUTPUT | MUX_MODE1) /* MII1_TXCLK, MSTP RX2 */
+ 0x164 (PIN_OUTPUT | MUX_MODE7) /* ECAP0_IN_PWM0_OUT, relay2 */
+ 0x168 (PIN_INPUT | MUX_MODE1) /* MII1_RXCLK, tpuart RX4 */
+ 0x16c (PIN_OUTPUT | MUX_MODE1) /* LCD_DATA9, tpuart TX4 */
+ 0x178 (PIN_OUTPUT | MUX_MODE7) /* UART1_CTS, UI */
+ 0x1b0 (PIN_OUTPUT | MUX_MODE7) /* XDMA_EVENT_INTR0, KNX Power */
+ 0x1d0 (PIN_INPUT | MUX_MODE0) /* tms jtag */
+ 0x1d4 (PIN_INPUT | MUX_MODE0) /* tdi jtag */
+ 0x1d8 (PIN_OUTPUT | MUX_MODE0) /* tdo jtag */
+ 0x1dc (PIN_INPUT | MUX_MODE0) /* tck jtag */
+ 0x1e0 (PIN_INPUT | MUX_MODE0) /* trstn jtag */
+ >;
+ };
+
+ user_leds_s0: user_leds_s0 {
+ pinctrl-single,pins = <
+ 0x88 (PIN_INPUT | MUX_MODE7) /* gpmc_csn3.gpio2_0 */
+ 0x1e4 (PIN_INPUT | MUX_MODE7) /* emu0.gpio3_7 */
+ >;
+ };
+
+ epwmss0_pins: epwmss0_pins {
+ pinctrl-single,pins = <
+ 0x150 (PIN_OUTPUT | MUX_MODE3) /* conf_spi0_sclk.ehrpwm0A */
+ 0x154 (PIN_OUTPUT | MUX_MODE3) /* conf_spi0_d0.ehrpwm0B */
+ >;
+ };
+
+ epwmss1_pins: epwmss1_pins {
+ pinctrl-single,pins = <
+ 0x0c8 (PIN_OUTPUT | MUX_MODE2) /* lcd_data10.lcd_data10 */
+ 0x0cc (PIN_OUTPUT | MUX_MODE2) /* lcd_data11.lcd_data11 */
+ >;
+ };
+
+ ecap1_pins: ecap1_pins {
+ pinctrl-single,pins = <
+ 0x160 (PIN_OUTPUT | MUX_MODE2) /* conf_spi0_cs1*/
+ >;
+ };
+
+ cpsw_default: cpsw_default {
+ pinctrl-single,pins = <
+ 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_crs.rmii1_crs_dv */
+ 0x114 (PIN_OUTPUT | MUX_MODE1) /* mii1_txen.mii1_txen */
+ 0x124 (PIN_OUTPUT | MUX_MODE1) /* mii1_txd1.mii1_txd1 */
+ 0x128 (PIN_OUTPUT | MUX_MODE1) /* mii1_txd0.mii1_txd0 */
+ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd1.mii1_rxd1 */
+ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd0.mii1_rxd0 */
+ 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii1_refclk.rmii1_refclk */
+ >;
+ };
+
+ cpsw_sleep: cpsw_sleep {
+ pinctrl-single,pins = <
+ 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
+
+ davinci_mdio_default: davinci_mdio_default {
+ pinctrl-single,pins = <
+ /* MDIO */
+ 0x148 (PIN_INPUT | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
+ 0x14c (PIN_OUTPUT | MUX_MODE0) /* mdio_clk.mdio_clk */
+ >;
+ };
+
+ davinci_mdio_sleep: davinci_mdio_sleep {
+ pinctrl-single,pins = <
+ /* MDIO reset value */
+ 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
+
+ gpio_mdio_default: gpio_mdio_default {
+ pinctrl-single,pins = <
+ /* MDIO via GPIO */
+ 0x148 (PIN_INPUT | MUX_MODE7) /* mdio_data.mdio_data GPIO0_0 */
+ 0x14c (PIN_OUTPUT | MUX_MODE7) /* mdio_clk.mdio_clk GPIO0_1 */
+ >;
+ };
+ };
+
+ ocp {
+ epwmss0: epwmss@48300000 {
+ status = "okay";
+ compatible = "ti,am33xx-pwmss";
+
+ ehrpwm0: ehrpwm@48300200 {
+ compatible = "ti,am33xx-ehrpwm";
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&epwmss0_pins>;
+ };
+ };
+
+ epwmss1: epwmss@48302000 {
+ status = "okay";
+ compatible = "ti,am33xx-pwmss";
+
+ ecap1: ecap@48302100 {
+ compatible = "ti,am33xx-ecap";
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&ecap1_pins>;
+ };
+
+ ehrpwm1: ehrpwm@48302200 {
+ compatible = "ti,am33xx-ehrpwm";
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&epwmss1_pins>;
+ };
+ };
+ };
+
+ leds {
+ pinctrl-names = "default";
+ pinctrl-0 = <&user_leds_s0>;
+ compatible = "gpio-leds";
+
+ led@0 {
+ label = "led0";
+ gpios = <&gpio2 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ led@1 {
+ label = "led1";
+ gpios = <&gpio3 7 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ };
+};
+
+&mac {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&cpsw_default>;
+ pinctrl-1 = <&cpsw_sleep>;
+ slaves = <1>; /* use only one emac if */
+
+ mdio0: gpio {
+ compatible = "virtual,mdio-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_mdio_default>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpios = <&gpio0 1 GPIO_ACTIVE_HIGH /* MDIO-CLK */
+ &gpio0 0 GPIO_ACTIVE_HIGH>; /* MDIO-DATA */
+
+ phy0: ethernet-phy@1 {
+ reg = <0>;
+ };
+ };
+};
+
+/* Disable davinci/am335x mdio interface on this platform */
+&davinci_mdio {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&davinci_mdio_default>;
+ pinctrl-1 = <&davinci_mdio_sleep>;
+ status = "disabled";
+};
+
+&cpsw_emac0 {
+ phy_id = <&mdio0>, <0>;
+ phy-mode = "rmii";
+};
+
+&phy_sel {
+ rmii-clock-ext;
+};
--
1.8.5.3
^ permalink raw reply related [flat|nested] 5+ messages in thread* Re: [PATCH 1/3] arm: dts: am33xx.dtsi: Add node name to rtc device node
2014-02-05 12:12 [PATCH 1/3] arm: dts: am33xx.dtsi: Add node name to rtc device node Stefan Roese
2014-02-05 12:12 ` [PATCH 2/3] arm: dts: Add Siemens Draco SOM dtsi Stefan Roese
2014-02-05 12:12 ` [PATCH 3/3] arm: dts: Add Siemens am335x-dxr2-e.dts Stefan Roese
@ 2014-02-05 18:29 ` Sergei Shtylyov
2014-02-28 22:45 ` Tony Lindgren
3 siblings, 0 replies; 5+ messages in thread
From: Sergei Shtylyov @ 2014-02-05 18:29 UTC (permalink / raw)
To: Stefan Roese, linux-arm-kernel
Cc: Tony Lindgren, Lukas Stockmann, linux-omap, Benoit Cousson
Hello.
On 02/05/2014 03:12 PM, Stefan Roese wrote:
> Making it possible to reference and therefor change (disable) this
> device node from other dts file which import this dtsi file.
> Signed-off-by: Stefan Roese <sr@denx.de>
> Cc: Lukas Stockmann <lukas.stockmann@siemens.com>
> Cc: Benoit Cousson <bcousson@baylibre.com>
> Cc: Tony Lindgren <tony@atomide.com>
> ---
> arch/arm/boot/dts/am33xx.dtsi | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
> diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
> index 6d95d3d..b8daf8c 100644
> --- a/arch/arm/boot/dts/am33xx.dtsi
> +++ b/arch/arm/boot/dts/am33xx.dtsi
> @@ -399,7 +399,7 @@
> ti,timer-pwm;
> };
>
> - rtc@44e3e000 {
> + rtc: rtc@44e3e000 {
Node name is "rtc@44e3e000" -- what you are adding is a label.
WBR, Sergei
^ permalink raw reply [flat|nested] 5+ messages in thread* Re: [PATCH 1/3] arm: dts: am33xx.dtsi: Add node name to rtc device node
2014-02-05 12:12 [PATCH 1/3] arm: dts: am33xx.dtsi: Add node name to rtc device node Stefan Roese
` (2 preceding siblings ...)
2014-02-05 18:29 ` [PATCH 1/3] arm: dts: am33xx.dtsi: Add node name to rtc device node Sergei Shtylyov
@ 2014-02-28 22:45 ` Tony Lindgren
3 siblings, 0 replies; 5+ messages in thread
From: Tony Lindgren @ 2014-02-28 22:45 UTC (permalink / raw)
To: Stefan Roese
Cc: linux-arm-kernel, linux-omap, Lukas Stockmann, Benoit Cousson
* Stefan Roese <sr@denx.de> [140205 04:14]:
> Making it possible to reference and therefor change (disable) this
> device node from other dts file which import this dtsi file.
>
> Signed-off-by: Stefan Roese <sr@denx.de>
> Cc: Lukas Stockmann <lukas.stockmann@siemens.com>
> Cc: Benoit Cousson <bcousson@baylibre.com>
> Cc: Tony Lindgren <tony@atomide.com>
Thanks applying into omap-for-v3.15/dt.
Tony
> ---
> arch/arm/boot/dts/am33xx.dtsi | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
> index 6d95d3d..b8daf8c 100644
> --- a/arch/arm/boot/dts/am33xx.dtsi
> +++ b/arch/arm/boot/dts/am33xx.dtsi
> @@ -399,7 +399,7 @@
> ti,timer-pwm;
> };
>
> - rtc@44e3e000 {
> + rtc: rtc@44e3e000 {
> compatible = "ti,da830-rtc";
> reg = <0x44e3e000 0x1000>;
> interrupts = <75
> --
> 1.8.5.3
>
^ permalink raw reply [flat|nested] 5+ messages in thread