linux-omap.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Pavel Machek <pavel@ucw.cz>
To: Sebastian Reichel <sre@kernel.org>
Cc: "Michael Welling" <mwelling@ieee.org>,
	"Pali Rohár" <pali.rohar@gmail.com>,
	"Tony Lindgren" <tony@atomide.com>,
	"Ivaylo Dimitrov" <ivo.g.dimitrov.75@gmail.com>,
	"Aaro Koskinen" <aaro.koskinen@iki.fi>,
	"Nishanth Menon" <nm@ti.com>,
	linux-omap@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: Re: linux 4.2-rc1 broken Nokia N900
Date: Wed, 22 Jul 2015 15:30:38 +0200	[thread overview]
Message-ID: <20150722133038.GA20106@amd> (raw)
In-Reply-To: <20150722020306.GA8379@earth>

On Wed 2015-07-22 04:03:07, Sebastian Reichel wrote:
> Hi,
> 
> On Tue, Jul 21, 2015 at 07:17:41PM -0500, Michael Welling wrote:
> > On Tue, Jul 21, 2015 at 11:34:41AM +0200, Pavel Machek wrote:
> > 
> > This code has my head spinning.
> > 
> > I found that the errors do not occur when the driver is built into the kernel.
> > 
> > I also found that with the patch below the errors go away.
> > 
> > Not sure if it is acceptible but see if it fixes things on your side.
> > 
> > 
> > diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c
> > index cf8b91b..3164d13 100644
> > --- a/drivers/spi/spi.c
> > +++ b/drivers/spi/spi.c
> > @@ -1801,11 +1801,11 @@ int spi_setup(struct spi_device *spi)
> >  	if (!spi->max_speed_hz)
> >  		spi->max_speed_hz = spi->master->max_speed_hz;
> >  
> > -	spi_set_cs(spi, false);
> > -
> >  	if (spi->master->setup)
> >  		status = spi->master->setup(spi);
> >  
> > +	spi_set_cs(spi, false);
> > +
> >  	dev_dbg(&spi->dev, "setup mode %d, %s%s%s%s%u bits/w, %u Hz max --> %d\n",
> >  			(int) (spi->mode & (SPI_CPOL | SPI_CPHA)),
> >  			(spi->mode & SPI_CS_HIGH) ? "cs_high, " : "",
> 
> mh. maybe a runtime PM issue?
> 
>  * external abort on non-linefetch: address cannot be accessed,
>    since the module's clocks are disabled
>  * built-in works, module not: built-in is probably a little bit
>    faster (module must not be loaded from filesystem), so that
>    the device has not yet been suspended
>  * Before 4.2, omap2_mcspi_set_cs() was called in the setup
>    routine, which acquired runtime PM
>  * In 4.2, omap2_mcspi_set_cs() seems to be called without a
>    prior pm_runtime_get_sync()
>  * With your workaround, the device has not yet returned to
>    suspend after the runtime PM acquisition in setup()
> 
> So I suggest trying the following (compile tested only) patch:

Solves problem for me. I had to apply it by patch -l.

Tested-by: Pavel Machek <pavel@ucw.cz>
									Pavel
									

> -- Sebastian
> 
> diff --git a/drivers/spi/spi-omap2-mcspi.c b/drivers/spi/spi-omap2-mcspi.c
> index 5867384..f7d9ffd 100644
> --- a/drivers/spi/spi-omap2-mcspi.c
> +++ b/drivers/spi/spi-omap2-mcspi.c
> @@ -245,6 +245,7 @@ static void omap2_mcspi_set_enable(const struct spi_device *spi, int enable)
>  
>  static void omap2_mcspi_set_cs(struct spi_device *spi, bool enable)
>  {
> +       struct omap2_mcspi *mcspi = spi_master_get_devdata(spi->master);
>         u32 l;
>  
>         /* The controller handles the inverted chip selects
> @@ -255,6 +256,8 @@ static void omap2_mcspi_set_cs(struct spi_device *spi, bool enable)
>                 enable = !enable;
>  
>         if (spi->controller_state) {
> +               pm_runtime_get_sync(mcspi->dev);
> +
>                 l = mcspi_cached_chconf0(spi);
>  
>                 if (enable)
> @@ -263,6 +266,9 @@ static void omap2_mcspi_set_cs(struct spi_device *spi, bool enable)
>                         l |= OMAP2_MCSPI_CHCONF_FORCE;
>  
>                 mcspi_write_chconf0(spi, l);
> +
> +               pm_runtime_mark_last_busy(mcspi->dev);
> +               pm_runtime_put_autosuspend(mcspi->dev);
>         }
>  }
>  



-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

  parent reply	other threads:[~2015-07-22 13:30 UTC|newest]

Thread overview: 53+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2015-07-11 12:05 linux 4.2-rc1 broken Nokia N900 Pali Rohár
2015-07-13  6:44 ` Tony Lindgren
2015-07-13  8:09   ` Sebastian Reichel
2015-07-13 17:03     ` Michael Welling
2015-07-13 17:09       ` Pali Rohár
2015-07-13 17:56         ` Michael Welling
2015-07-13 20:28         ` Michael Welling
2015-07-13 20:34           ` Pali Rohár
2015-07-13 21:52             ` Michael Welling
2015-07-13 22:02               ` Pali Rohár
2015-07-13 22:36                 ` Michael Welling
2015-07-14  7:14                   ` Pali Rohár
2015-07-14  7:45                     ` Tony Lindgren
2015-07-14 16:33                     ` Michael Welling
2015-07-14 20:01                       ` Pavel Machek
2015-07-14 20:17                         ` Michael Welling
2015-07-15 19:49                           ` Pavel Machek
2015-07-15 20:10                             ` Michael Welling
2015-07-21  7:31                               ` Pavel Machek
2015-07-21  7:33                                 ` Pavel Machek
2015-07-21  8:04                                   ` Pali Rohár
2015-07-20 20:48                             ` Michael Welling
2015-07-20 20:46                     ` Michael Welling
2015-07-20 20:58                       ` Pali Rohár
2015-07-21  9:34                       ` Pavel Machek
2015-07-21 21:28                         ` Michael Welling
2015-07-22  0:17                         ` Michael Welling
2015-07-22  2:03                           ` Sebastian Reichel
2015-07-22  5:13                             ` Michael Welling
2015-07-22  7:27                               ` Pali Rohár
2015-07-22 13:33                                 ` Sebastian Reichel
2015-07-22 14:27                                   ` Pali Rohár
2015-07-22 13:30                             ` Pavel Machek [this message]
2015-07-25  8:55                             ` Pali Rohár
2015-07-28  8:39                               ` Pali Rohár
2015-07-28 12:26                                 ` Sebastian Reichel
2015-07-28 12:32                                   ` Pali Rohár
2015-07-13 11:10   ` Pali Rohár
2015-07-13 13:26     ` Tony Lindgren
2015-07-13 15:51 ` Sebastian Reichel
2015-07-13 16:05   ` Pali Rohár
2015-07-13 19:32     ` Sebastian Reichel
2015-07-14  0:18       ` Krzysztof Kozlowski
2015-07-24  8:18 ` Dave Young
2015-07-24  8:30   ` Ivaylo Dimitrov
2015-07-24 10:28     ` Dave Young
2015-07-24 10:53       ` Pali Rohár
2015-07-24  8:40   ` Pali Rohár
2015-07-24 10:33     ` Dave Young
2015-07-24 10:52       ` Pali Rohár
2015-07-24 15:50     ` Pali Rohár
2015-07-24  8:51   ` Pavel Machek
2015-07-24 10:39     ` Dave Young

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20150722133038.GA20106@amd \
    --to=pavel@ucw.cz \
    --cc=aaro.koskinen@iki.fi \
    --cc=ivo.g.dimitrov.75@gmail.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-omap@vger.kernel.org \
    --cc=mwelling@ieee.org \
    --cc=nm@ti.com \
    --cc=pali.rohar@gmail.com \
    --cc=sre@kernel.org \
    --cc=tony@atomide.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).