From: Tony Lindgren <tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>
To: linux-omap-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: "Benoît Cousson"
<bcousson-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
"Dmitry Lifshitz"
<lifshitz-UTxiZqZC01RS1MOuV/RT9w@public.gmane.org>,
"Tomi Valkeinen" <tomi.valkeinen-l0cyMroinI0@public.gmane.org>
Subject: [PATCH] ARM: dts: Disable HDMI CEC internal pull-ups
Date: Tue, 27 Jun 2017 01:58:32 -0700 [thread overview]
Message-ID: <20170627085832.30949-1-tony@atomide.com> (raw)
Devices using an external encoder, ESD protection and level shifter
such as tpd12s015 or ip4791cz12 have the CEC pull in the encoder
chip. And on var-som-om44, there is external pull up resistor R30.
So the internal CEC pull-up resistor needs to be disabled as otherwise
the external and internal pull are parallel making the pull value
much smaller than intended. This leads into the CEC not working as
reported by Hans Verkuil <hverkuil-qWit8jRvyhVmR6Xm/wNWPw@public.gmane.org>.
Reported-by: Hans Verkuil <hverkuil-qWit8jRvyhVmR6Xm/wNWPw@public.gmane.org>
Cc: Dmitry Lifshitz <lifshitz-UTxiZqZC01RS1MOuV/RT9w@public.gmane.org>
Cc: Tomi Valkeinen <tomi.valkeinen-l0cyMroinI0@public.gmane.org>
Signed-off-by: Tony Lindgren <tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>
---
Dmitry, care to check that also omap5-cm-t54 has external pull on CEC pin?
---
arch/arm/boot/dts/omap4-droid4-xt894.dts | 2 +-
arch/arm/boot/dts/omap4-duovero-parlor.dts | 2 +-
arch/arm/boot/dts/omap4-panda-common.dtsi | 2 +-
arch/arm/boot/dts/omap4-sdp-es23plus.dts | 2 +-
arch/arm/boot/dts/omap4-sdp.dts | 2 +-
arch/arm/boot/dts/omap4-var-om44customboard.dtsi | 2 +-
arch/arm/boot/dts/omap5-board-common.dtsi | 2 +-
arch/arm/boot/dts/omap5-cm-t54.dts | 2 +-
8 files changed, 8 insertions(+), 8 deletions(-)
diff --git a/arch/arm/boot/dts/omap4-droid4-xt894.dts b/arch/arm/boot/dts/omap4-droid4-xt894.dts
--- a/arch/arm/boot/dts/omap4-droid4-xt894.dts
+++ b/arch/arm/boot/dts/omap4-droid4-xt894.dts
@@ -373,7 +373,7 @@
/* hdmi_cec.hdmi_cec, hdmi_scl.hdmi_scl, hdmi_sda.hdmi_sda */
dss_hdmi_pins: pinmux_dss_hdmi_pins {
pinctrl-single,pins = <
- OMAP4_IOPAD(0x09a, PIN_INPUT_PULLUP | MUX_MODE0)
+ OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0)
OMAP4_IOPAD(0x09c, PIN_INPUT | MUX_MODE0)
OMAP4_IOPAD(0x09e, PIN_INPUT | MUX_MODE0)
>;
diff --git a/arch/arm/boot/dts/omap4-duovero-parlor.dts b/arch/arm/boot/dts/omap4-duovero-parlor.dts
--- a/arch/arm/boot/dts/omap4-duovero-parlor.dts
+++ b/arch/arm/boot/dts/omap4-duovero-parlor.dts
@@ -100,7 +100,7 @@
dss_hdmi_pins: pinmux_dss_hdmi_pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x098, PIN_INPUT | MUX_MODE3) /* hdmi_hpd.gpio_63 */
- OMAP4_IOPAD(0x09a, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */
+ OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0) /* hdmi_cec.hdmi_cec */
OMAP4_IOPAD(0x09c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_ddc_scl.hdmi_ddc_scl */
OMAP4_IOPAD(0x09e, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_ddc_sda.hdmi_ddc_sda */
>;
diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi
--- a/arch/arm/boot/dts/omap4-panda-common.dtsi
+++ b/arch/arm/boot/dts/omap4-panda-common.dtsi
@@ -267,7 +267,7 @@
dss_hdmi_pins: pinmux_dss_hdmi_pins {
pinctrl-single,pins = <
- OMAP4_IOPAD(0x09a, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */
+ OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0) /* hdmi_cec.hdmi_cec */
OMAP4_IOPAD(0x09c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_scl.hdmi_scl */
OMAP4_IOPAD(0x09e, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_sda.hdmi_sda */
>;
diff --git a/arch/arm/boot/dts/omap4-sdp-es23plus.dts b/arch/arm/boot/dts/omap4-sdp-es23plus.dts
--- a/arch/arm/boot/dts/omap4-sdp-es23plus.dts
+++ b/arch/arm/boot/dts/omap4-sdp-es23plus.dts
@@ -10,7 +10,7 @@
/* SDP boards with 4430 ES2.3+ or 4460 have external pullups on SCL & SDA */
&dss_hdmi_pins {
pinctrl-single,pins = <
- OMAP4_IOPAD(0x09a, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */
+ OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0) /* hdmi_cec.hdmi_cec */
OMAP4_IOPAD(0x09c, PIN_INPUT | MUX_MODE0) /* hdmi_scl.hdmi_scl */
OMAP4_IOPAD(0x09e, PIN_INPUT | MUX_MODE0) /* hdmi_sda.hdmi_sda */
>;
diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts
--- a/arch/arm/boot/dts/omap4-sdp.dts
+++ b/arch/arm/boot/dts/omap4-sdp.dts
@@ -290,7 +290,7 @@
dss_hdmi_pins: pinmux_dss_hdmi_pins {
pinctrl-single,pins = <
- OMAP4_IOPAD(0x09a, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */
+ OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0) /* hdmi_cec.hdmi_cec */
OMAP4_IOPAD(0x09c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_scl.hdmi_scl */
OMAP4_IOPAD(0x09e, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_sda.hdmi_sda */
>;
diff --git a/arch/arm/boot/dts/omap4-var-om44customboard.dtsi b/arch/arm/boot/dts/omap4-var-om44customboard.dtsi
--- a/arch/arm/boot/dts/omap4-var-om44customboard.dtsi
+++ b/arch/arm/boot/dts/omap4-var-om44customboard.dtsi
@@ -122,7 +122,7 @@
dss_hdmi_pins: pinmux_dss_hdmi_pins {
pinctrl-single,pins = <
- OMAP4_IOPAD(0x09a, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */
+ OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0) /* hdmi_cec.hdmi_cec */
OMAP4_IOPAD(0x09c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_scl.hdmi_scl */
OMAP4_IOPAD(0x09e, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_sda.hdmi_sda */
>;
diff --git a/arch/arm/boot/dts/omap5-board-common.dtsi b/arch/arm/boot/dts/omap5-board-common.dtsi
--- a/arch/arm/boot/dts/omap5-board-common.dtsi
+++ b/arch/arm/boot/dts/omap5-board-common.dtsi
@@ -294,7 +294,7 @@
dss_hdmi_pins: pinmux_dss_hdmi_pins {
pinctrl-single,pins = <
- OMAP5_IOPAD(0x13c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */
+ OMAP5_IOPAD(0x13c, PIN_INPUT | MUX_MODE0) /* hdmi_cec.hdmi_cec */
OMAP5_IOPAD(0x140, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl.hdmi_ddc_scl */
OMAP5_IOPAD(0x142, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_sda.hdmi_ddc_sda */
>;
diff --git a/arch/arm/boot/dts/omap5-cm-t54.dts b/arch/arm/boot/dts/omap5-cm-t54.dts
--- a/arch/arm/boot/dts/omap5-cm-t54.dts
+++ b/arch/arm/boot/dts/omap5-cm-t54.dts
@@ -266,7 +266,7 @@
dss_hdmi_pins: pinmux_dss_hdmi_pins {
pinctrl-single,pins = <
- OMAP5_IOPAD(0x013c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec */
+ OMAP5_IOPAD(0x013c, PIN_INPUT | MUX_MODE0) /* hdmi_cec */
OMAP5_IOPAD(0x0140, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl */
OMAP5_IOPAD(0x0142, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_sda */
>;
--
2.13.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next reply other threads:[~2017-06-27 8:58 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-06-27 8:58 Tony Lindgren [this message]
[not found] ` <20170627085832.30949-1-tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>
2017-06-27 9:06 ` [PATCH] ARM: dts: Disable HDMI CEC internal pull-ups Sebastian Reichel
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20170627085832.30949-1-tony@atomide.com \
--to=tony-4v6ys6ai5vpbdgjk7y7tuq@public.gmane.org \
--cc=bcousson-rdvid1DuHRBWk0Htik3J/w@public.gmane.org \
--cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=lifshitz-UTxiZqZC01RS1MOuV/RT9w@public.gmane.org \
--cc=linux-omap-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=tomi.valkeinen-l0cyMroinI0@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox