From: Tony Lindgren <tony@atomide.com>
To: linux-omap@vger.kernel.org
Cc: Nishanth Menon <nm@ti.com>,
Grygorii Strashko <grygorii.strashko@ti.com>,
Marcel Partap <mpartap@gmx.net>, Dave Gerlach <d-gerlach@ti.com>,
Pavel Machek <pavel@ucw.cz>, Keerthy <j-keerthy@ti.com>,
Merlijn Wajer <merlijn@wizzup.org>,
Sebastian Reichel <sre@kernel.org>, Tero Kristo <t-kristo@ti.com>,
NeKit <nekit1000@gmail.com>, Eyal Reizer <eyalr@ti.com>,
linux-arm-kernel@lists.infradead.org,
Michael Scott <hashcode0f@gmail.com>,
Kalle Valo <kvalo@codeaurora.org>, Ash Charles <ash@gumstix.com>
Subject: [PATCH 2/4] ARM: dts: Fix omap l4per idling with wlcore edge sensitive interrupt
Date: Thu, 17 May 2018 16:35:40 -0700 [thread overview]
Message-ID: <20180517233542.30629-3-tony@atomide.com> (raw)
In-Reply-To: <20180517233542.30629-1-tony@atomide.com>
The wl1835mod.pdf data sheet says this pretty clearly for WL_IRQ line:
"WLAN SDIO out-of-band interrupt line. Set to rising edge (active high)
by default."
And it seems this interrupt can be optionally configured to use falling
edge too since commit bd763482c82e ("wl18xx: wlan_irq: support platform
dependent interrupt types").
On omaps, if the wlcore interrupt is configured as level instead of edge,
L4PER will stop doing hardware based idling after ifconfig wlan0 down is
done and the WL_EN line is pulled down.
The symptoms show up with L4PER status registers no longer showing the
IDLEST bits as 2 but as 0 for all the active GPIO banks and for
L4PER_CLKCTRL. Also the l4per_pwrdm RET count stops increasing in
the /sys/kernel/debug/pm_debug/count.
I'm guessing wlcore was at some point configured to use level interrupts
because of edge handling issues in gpio-omap. However, with the recent
fixes to gpio-omap the edge interrupts seem to be working just fine.
Let's fix the issue for all omap boards with wlcore interrupt set as level.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Eyal Reizer <eyalr@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/boot/dts/am335x-baltos.dtsi | 2 +-
arch/arm/boot/dts/am335x-evm.dts | 2 +-
arch/arm/boot/dts/am335x-evmsk.dts | 2 +-
arch/arm/boot/dts/am437x-gp-evm.dts | 2 +-
arch/arm/boot/dts/logicpd-som-lv.dtsi | 2 +-
arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts | 2 +-
arch/arm/boot/dts/omap3-cm-t3517.dts | 2 +-
arch/arm/boot/dts/omap3-cm-t3730.dts | 2 +-
arch/arm/boot/dts/omap3-evm-common.dtsi | 2 +-
arch/arm/boot/dts/omap3-igep0020-rev-f.dts | 2 +-
arch/arm/boot/dts/omap3-igep0030-rev-g.dts | 2 +-
arch/arm/boot/dts/omap3-zoom3.dts | 2 +-
arch/arm/boot/dts/omap4-droid4-xt894.dts | 2 +-
arch/arm/boot/dts/omap4-panda-common.dtsi | 2 +-
arch/arm/boot/dts/omap4-sdp.dts | 2 +-
arch/arm/boot/dts/omap4-var-som-om44-wlan.dtsi | 2 +-
arch/arm/boot/dts/omap5-board-common.dtsi | 2 +-
17 files changed, 17 insertions(+), 17 deletions(-)
diff --git a/arch/arm/boot/dts/am335x-baltos.dtsi b/arch/arm/boot/dts/am335x-baltos.dtsi
--- a/arch/arm/boot/dts/am335x-baltos.dtsi
+++ b/arch/arm/boot/dts/am335x-baltos.dtsi
@@ -396,7 +396,7 @@
compatible = "ti,wl1835";
reg = <2>;
interrupt-parent = <&gpio3>;
- interrupts = <7 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <7 IRQ_TYPE_EDGE_RISING>;
};
};
diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/am335x-evm.dts
--- a/arch/arm/boot/dts/am335x-evm.dts
+++ b/arch/arm/boot/dts/am335x-evm.dts
@@ -771,7 +771,7 @@
compatible = "ti,wl1835";
reg = <2>;
interrupt-parent = <&gpio3>;
- interrupts = <17 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <17 IRQ_TYPE_EDGE_RISING>;
};
};
diff --git a/arch/arm/boot/dts/am335x-evmsk.dts b/arch/arm/boot/dts/am335x-evmsk.dts
--- a/arch/arm/boot/dts/am335x-evmsk.dts
+++ b/arch/arm/boot/dts/am335x-evmsk.dts
@@ -682,7 +682,7 @@
compatible = "ti,wl1271";
reg = <2>;
interrupt-parent = <&gpio0>;
- interrupts = <31 IRQ_TYPE_LEVEL_HIGH>; /* gpio 31 */
+ interrupts = <31 IRQ_TYPE_EDGE_RISING>; /* gpio 31 */
ref-clock-frequency = <38400000>;
};
};
diff --git a/arch/arm/boot/dts/am437x-gp-evm.dts b/arch/arm/boot/dts/am437x-gp-evm.dts
--- a/arch/arm/boot/dts/am437x-gp-evm.dts
+++ b/arch/arm/boot/dts/am437x-gp-evm.dts
@@ -790,7 +790,7 @@
compatible = "ti,wl1835";
reg = <2>;
interrupt-parent = <&gpio1>;
- interrupts = <23 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <23 IRQ_TYPE_EDGE_RISING>;
};
};
diff --git a/arch/arm/boot/dts/logicpd-som-lv.dtsi b/arch/arm/boot/dts/logicpd-som-lv.dtsi
--- a/arch/arm/boot/dts/logicpd-som-lv.dtsi
+++ b/arch/arm/boot/dts/logicpd-som-lv.dtsi
@@ -113,7 +113,7 @@
compatible = "ti,wl1273";
reg = <2>;
interrupt-parent = <&gpio1>;
- interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; /* gpio 2 */
+ interrupts = <2 IRQ_TYPE_EDGE_RISING>; /* gpio 2 */
ref-clock-frequency = <26000000>;
};
};
diff --git a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts
--- a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts
+++ b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts
@@ -48,7 +48,7 @@
compatible = "ti,wl1283";
reg = <2>;
interrupt-parent = <&gpio5>;
- interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */
+ interrupts = <24 IRQ_TYPE_EDGE_RISING>; /* gpio 152 */
ref-clock-frequency = <26000000>;
tcxo-clock-frequency = <26000000>;
};
diff --git a/arch/arm/boot/dts/omap3-cm-t3517.dts b/arch/arm/boot/dts/omap3-cm-t3517.dts
--- a/arch/arm/boot/dts/omap3-cm-t3517.dts
+++ b/arch/arm/boot/dts/omap3-cm-t3517.dts
@@ -141,7 +141,7 @@
compatible = "ti,wl1271";
reg = <2>;
interrupt-parent = <&gpio5>;
- interrupts = <17 IRQ_TYPE_LEVEL_HIGH>; /* gpio 145 */
+ interrupts = <17 IRQ_TYPE_EDGE_RISING>; /* gpio 145 */
ref-clock-frequency = <38400000>;
};
};
diff --git a/arch/arm/boot/dts/omap3-cm-t3730.dts b/arch/arm/boot/dts/omap3-cm-t3730.dts
--- a/arch/arm/boot/dts/omap3-cm-t3730.dts
+++ b/arch/arm/boot/dts/omap3-cm-t3730.dts
@@ -81,7 +81,7 @@
compatible = "ti,wl1271";
reg = <2>;
interrupt-parent = <&gpio5>;
- interrupts = <8 IRQ_TYPE_LEVEL_HIGH>; /* gpio 136 */
+ interrupts = <8 IRQ_TYPE_EDGE_RISING>; /* gpio 136 */
ref-clock-frequency = <38400000>;
};
};
diff --git a/arch/arm/boot/dts/omap3-evm-common.dtsi b/arch/arm/boot/dts/omap3-evm-common.dtsi
--- a/arch/arm/boot/dts/omap3-evm-common.dtsi
+++ b/arch/arm/boot/dts/omap3-evm-common.dtsi
@@ -133,7 +133,7 @@
compatible = "ti,wl1271";
reg = <2>;
interrupt-parent = <&gpio5>;
- interrupts = <21 IRQ_TYPE_LEVEL_HIGH>; /* gpio 149 */
+ interrupts = <21 IRQ_TYPE_EDGE_RISING>; /* gpio 149 */
ref-clock-frequency = <38400000>;
};
};
diff --git a/arch/arm/boot/dts/omap3-igep0020-rev-f.dts b/arch/arm/boot/dts/omap3-igep0020-rev-f.dts
--- a/arch/arm/boot/dts/omap3-igep0020-rev-f.dts
+++ b/arch/arm/boot/dts/omap3-igep0020-rev-f.dts
@@ -49,6 +49,6 @@
compatible = "ti,wl1835";
reg = <2>;
interrupt-parent = <&gpio6>;
- interrupts = <17 IRQ_TYPE_LEVEL_HIGH>; /* gpio 177 */
+ interrupts = <17 IRQ_TYPE_EDGE_RISING>; /* gpio 177 */
};
};
diff --git a/arch/arm/boot/dts/omap3-igep0030-rev-g.dts b/arch/arm/boot/dts/omap3-igep0030-rev-g.dts
--- a/arch/arm/boot/dts/omap3-igep0030-rev-g.dts
+++ b/arch/arm/boot/dts/omap3-igep0030-rev-g.dts
@@ -71,6 +71,6 @@
compatible = "ti,wl1835";
reg = <2>;
interrupt-parent = <&gpio5>;
- interrupts = <8 IRQ_TYPE_LEVEL_HIGH>; /* gpio 136 */
+ interrupts = <8 IRQ_TYPE_EDGE_RISING>; /* gpio 136 */
};
};
diff --git a/arch/arm/boot/dts/omap3-zoom3.dts b/arch/arm/boot/dts/omap3-zoom3.dts
--- a/arch/arm/boot/dts/omap3-zoom3.dts
+++ b/arch/arm/boot/dts/omap3-zoom3.dts
@@ -202,7 +202,7 @@
compatible = "ti,wl1271";
reg = <2>;
interrupt-parent = <&gpio6>;
- interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; /* gpio 162 */
+ interrupts = <2 IRQ_TYPE_EDGE_RISING>; /* gpio 162 */
ref-clock-frequency = <26000000>;
};
};
diff --git a/arch/arm/boot/dts/omap4-droid4-xt894.dts b/arch/arm/boot/dts/omap4-droid4-xt894.dts
--- a/arch/arm/boot/dts/omap4-droid4-xt894.dts
+++ b/arch/arm/boot/dts/omap4-droid4-xt894.dts
@@ -372,7 +372,7 @@
compatible = "ti,wl1285", "ti,wl1283";
reg = <2>;
interrupt-parent = <&gpio4>;
- interrupts = <4 IRQ_TYPE_LEVEL_HIGH>; /* gpio100 */
+ interrupts = <4 IRQ_TYPE_EDGE_RISING>; /* gpio100 */
ref-clock-frequency = <26000000>;
tcxo-clock-frequency = <26000000>;
};
diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi
--- a/arch/arm/boot/dts/omap4-panda-common.dtsi
+++ b/arch/arm/boot/dts/omap4-panda-common.dtsi
@@ -464,7 +464,7 @@
compatible = "ti,wl1271";
reg = <2>;
interrupt-parent = <&gpio2>;
- interrupts = <21 IRQ_TYPE_LEVEL_HIGH>; /* gpio 53 */
+ interrupts = <21 IRQ_TYPE_EDGE_RISING>; /* gpio 53 */
ref-clock-frequency = <38400000>;
};
};
diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts
--- a/arch/arm/boot/dts/omap4-sdp.dts
+++ b/arch/arm/boot/dts/omap4-sdp.dts
@@ -493,7 +493,7 @@
compatible = "ti,wl1281";
reg = <2>;
interrupt-parent = <&gpio1>;
- interrupts = <21 IRQ_TYPE_LEVEL_HIGH>; /* gpio 53 */
+ interrupts = <21 IRQ_TYPE_EDGE_RISING>; /* gpio 53 */
ref-clock-frequency = <26000000>;
tcxo-clock-frequency = <26000000>;
};
diff --git a/arch/arm/boot/dts/omap4-var-som-om44-wlan.dtsi b/arch/arm/boot/dts/omap4-var-som-om44-wlan.dtsi
--- a/arch/arm/boot/dts/omap4-var-som-om44-wlan.dtsi
+++ b/arch/arm/boot/dts/omap4-var-som-om44-wlan.dtsi
@@ -72,7 +72,7 @@
compatible = "ti,wl1271";
reg = <2>;
interrupt-parent = <&gpio2>;
- interrupts = <9 IRQ_TYPE_LEVEL_HIGH>; /* gpio 41 */
+ interrupts = <9 IRQ_TYPE_EDGE_RISING>; /* gpio 41 */
ref-clock-frequency = <38400000>;
};
};
diff --git a/arch/arm/boot/dts/omap5-board-common.dtsi b/arch/arm/boot/dts/omap5-board-common.dtsi
--- a/arch/arm/boot/dts/omap5-board-common.dtsi
+++ b/arch/arm/boot/dts/omap5-board-common.dtsi
@@ -364,7 +364,7 @@
pinctrl-names = "default";
pinctrl-0 = <&wlcore_irq_pin>;
interrupt-parent = <&gpio1>;
- interrupts = <14 IRQ_TYPE_LEVEL_HIGH>; /* gpio 14 */
+ interrupts = <14 IRQ_TYPE_EDGE_RISING>; /* gpio 14 */
ref-clock-frequency = <26000000>;
};
};
--
2.17.0
next prev parent reply other threads:[~2018-05-17 23:35 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-05-17 23:35 [PATCH 0/4] Correct wlcore irqs for PM improvments for omap4 boards Tony Lindgren
2018-05-17 23:35 ` [PATCH 1/4] ARM: OMAP2+: Make sure LOGICRETSTATE bits are not cleared Tony Lindgren
2018-05-17 23:35 ` Tony Lindgren [this message]
2018-05-17 23:35 ` [PATCH 3/4] ARM: dts: Configure duovero for to allow core retention during idle Tony Lindgren
2018-05-17 23:35 ` [PATCH 4/4] omap4-droid4: Use software debounce for gpio-keys Tony Lindgren
2018-05-18 7:21 ` Pavel Machek
2018-05-18 14:32 ` Tony Lindgren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180517233542.30629-3-tony@atomide.com \
--to=tony@atomide.com \
--cc=ash@gumstix.com \
--cc=d-gerlach@ti.com \
--cc=eyalr@ti.com \
--cc=grygorii.strashko@ti.com \
--cc=hashcode0f@gmail.com \
--cc=j-keerthy@ti.com \
--cc=kvalo@codeaurora.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-omap@vger.kernel.org \
--cc=merlijn@wizzup.org \
--cc=mpartap@gmx.net \
--cc=nekit1000@gmail.com \
--cc=nm@ti.com \
--cc=pavel@ucw.cz \
--cc=sre@kernel.org \
--cc=t-kristo@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).