public inbox for linux-omap@vger.kernel.org
 help / color / mirror / Atom feed
From: Grygorii Strashko <grygorii.strashko@ti.com>
To: "David S. Miller" <davem@davemloft.net>,
	Tony Lindgren <tony@atomide.com>,
	Kishon Vijay Abraham I <kishon@ti.com>,
	Rob Herring <robh+dt@kernel.org>
Cc: netdev@vger.kernel.org, Sekhar Nori <nsekhar@ti.com>,
	linux-kernel@vger.kernel.org,
	linux-arm-kernel@lists.infradead.org,
	Andrew Lunn <andrew@lunn.ch>,
	devicetree@vger.kernel.org, linux-omap@vger.kernel.org,
	Grygorii Strashko <grygorii.strashko@ti.com>
Subject: [PATCH linux-next 10/10] net: ethernet: ti: cpsw: deprecate cpsw-phy-sel driver
Date: Sun, 25 Nov 2018 18:15:31 -0600	[thread overview]
Message-ID: <20181126001531.12974-11-grygorii.strashko@ti.com> (raw)
In-Reply-To: <20181126001531.12974-1-grygorii.strashko@ti.com>

Deprecate cpsw-phy-sel driver as it's been replaced with new
TI phy-gmii-sel PHY driver.

Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
---
 drivers/net/ethernet/ti/Kconfig | 6 +++---
 drivers/net/ethernet/ti/cpsw.h  | 6 ++++++
 2 files changed, 9 insertions(+), 3 deletions(-)

diff --git a/drivers/net/ethernet/ti/Kconfig b/drivers/net/ethernet/ti/Kconfig
index f932923..96415da 100644
--- a/drivers/net/ethernet/ti/Kconfig
+++ b/drivers/net/ethernet/ti/Kconfig
@@ -49,10 +49,11 @@ config TI_DAVINCI_CPDMA
 	  will be called davinci_cpdma.  This is recommended.
 
 config TI_CPSW_PHY_SEL
-	bool
+	bool "TI CPSW Phy mode Selection (DEPRECATED)"
+	default n
 	---help---
 	  This driver supports configuring of the phy mode connected to
-	  the CPSW.
+	  the CPSW. DEPRECATED: use PHY_TI_GMII_SEL.
 
 config TI_CPSW_ALE
 	tristate "TI CPSW ALE Support"
@@ -64,7 +65,6 @@ config TI_CPSW
 	depends on ARCH_DAVINCI || ARCH_OMAP2PLUS || COMPILE_TEST
 	select TI_DAVINCI_CPDMA
 	select TI_DAVINCI_MDIO
-	select TI_CPSW_PHY_SEL
 	select TI_CPSW_ALE
 	select MFD_SYSCON
 	select REGMAP
diff --git a/drivers/net/ethernet/ti/cpsw.h b/drivers/net/ethernet/ti/cpsw.h
index cf111db..907e05fc 100644
--- a/drivers/net/ethernet/ti/cpsw.h
+++ b/drivers/net/ethernet/ti/cpsw.h
@@ -21,7 +21,13 @@
 			 ((mac)[2] << 16) | ((mac)[3] << 24))
 #define mac_lo(mac)	(((mac)[4] << 0) | ((mac)[5] << 8))
 
+#if IS_ENABLED(CONFIG_TI_CPSW_PHY_SEL)
 void cpsw_phy_sel(struct device *dev, phy_interface_t phy_mode, int slave);
+#else
+static inline
+void cpsw_phy_sel(struct device *dev, phy_interface_t phy_mode, int slave)
+{}
+#endif
 int ti_cm_get_macid(struct device *dev, int slave, u8 *mac_addr);
 
 #endif /* __CPSW_H__ */
-- 
2.10.5

      parent reply	other threads:[~2018-11-26  0:15 UTC|newest]

Thread overview: 14+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-11-26  0:15 [PATCH linux-next 00/10] net: ethernet: ti: cpsw: replace cpsw-phy-sel with phy driver Grygorii Strashko
2018-11-26  0:15 ` [PATCH linux-next 01/10] dt-bindings: phy: add cpsw port interface mode selection phy bindings Grygorii Strashko
2018-11-27 18:22   ` Tony Lindgren
2018-11-26  0:15 ` [PATCH linux-next 02/10] phy: ti: introduce phy-gmii-sel driver Grygorii Strashko
2018-11-26  0:15 ` [PATCH linux-next 03/10] dt-bindings: net: ti: cpsw: switch to use phy-gmii-sel phy Grygorii Strashko
2018-11-26  0:15 ` [PATCH linux-next 04/10] net: ethernet: ti: cpsw: add support for port interface mode selection phy Grygorii Strashko
2018-11-26  0:15 ` [PATCH linux-next 05/10] ARM: dts: dra7: switch to use phy-gmii-sel Grygorii Strashko
2018-11-26  0:15 ` [PATCH linux-next 06/10] ARM: dts: dm814x: " Grygorii Strashko
2018-11-26  0:15 ` [PATCH linux-next 07/10] ARM: dts: am4372: " Grygorii Strashko
2018-11-26  0:15 ` [PATCH linux-next 08/10] ARM: dts: am335x: " Grygorii Strashko
2018-11-26  0:15 ` [PATCH linux-next 09/10] dt-bindings: net: ti: deprecate cpsw-phy-sel bindings Grygorii Strashko
2018-11-26 19:58   ` Rob Herring
2018-11-27 18:29     ` Grygorii Strashko
2018-11-26  0:15 ` Grygorii Strashko [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20181126001531.12974-11-grygorii.strashko@ti.com \
    --to=grygorii.strashko@ti.com \
    --cc=andrew@lunn.ch \
    --cc=davem@davemloft.net \
    --cc=devicetree@vger.kernel.org \
    --cc=kishon@ti.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-omap@vger.kernel.org \
    --cc=netdev@vger.kernel.org \
    --cc=nsekhar@ti.com \
    --cc=robh+dt@kernel.org \
    --cc=tony@atomide.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox