Copying executables into H2 board

Copying executables into H2 board

[Phanee Sistla]

I have the linux 2.6.9 kernel up and running on the OMAP1610 H2 board.
Booting the kernel from H2 board generates the follwoing o/p on the minicom
terminal:


MUX: Setting register MMC_DAT0
      FUNC_MUX_CTRL_B (0xfffe1030) = 0x00000000 -> 0x00000000
      PU_PD_SEL_2 (0xfffe10bc) = 0x0041f000 -> 0x0041f000
      PULL_DWN_CTRL_2 (0xfffe1048) = 0x00000410 -> 0x00000410

 MMC card not present
MMC1: Unable to get IRQ for MMC cover switch
OMAP16XX TSC2101 Audio support initialized
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET: Registered protocol family 1
NET: Registered protocol family 17
eth0: link up
Sending DHCP requests ., OK
IP-Config: Got DHCP answer from 129.119.113.107, my address is
129.119.126.126
IP-Config: Complete:
      device=eth0, addr=129.119.126.126, mask=255.255.255.0, gw=
129.119.126.1,
     host= 129.119.126.126, domain=seas.smu.edu, nis-domain=(none),
     bootserver=129.119.113.107, rootserver=129.119.124.64 , rootpath=<7>
evbug.c: Event. Dev: <NULL>, Type: 1, Code: 184, Value: 2
Looking up port of RPC 100003/2 on 129.119.124.64
Looking up port of RPC 100005/1 on 129.119.124.64
VFS: Mounted root (nfs filesystem).
Mounted devfs on /dev
Freeing init memory: 104K
init started:  BusyBox v1.00-pre8 (2004.03.05-22:18+0000) multi-call binary

******************************************
Starting System Init for innovator
******************************************

Please press Enter to activate this console.


The target board has a root file system that is NFS mounted from the host
pc. I tried to run a simple c program " Helloworld.c" from the H2 board. For
this I cross compiled the source code using snapgear toolchain. This
generated an executable "Helloworld". I dont know how to load this
executable into the H2 board. Kindly help me in this regard.

Thanking you in advance,
Phanee

Re: Copying executables into H2 board

[Francisco Alecrim]

ext Phanee Sistla wrote:
> I have the linux 2.6.9 kernel up and running on the OMAP1610 H2 board.
> Booting the kernel from H2 board generates the follwoing o/p on the minicom
> terminal:
>
>
> MUX: Setting register MMC_DAT0
>       FUNC_MUX_CTRL_B (0xfffe1030) = 0x00000000 -> 0x00000000
>       PU_PD_SEL_2 (0xfffe10bc) = 0x0041f000 -> 0x0041f000
>       PULL_DWN_CTRL_2 (0xfffe1048) = 0x00000410 -> 0x00000410
>
>  MMC card not present
> MMC1: Unable to get IRQ for MMC cover switch
> OMAP16XX TSC2101 Audio support initialized
> NET: Registered protocol family 2
> IP: routing cache hash table of 512 buckets, 4Kbytes
> TCP: Hash tables configured (established 2048 bind 4096)
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> eth0: link up
> Sending DHCP requests ., OK
> IP-Config: Got DHCP answer from 129.119.113.107, my address is
> 129.119.126.126
> IP-Config: Complete:
>       device=eth0, addr=129.119.126.126, mask=255.255.255.0, gw=
> 129.119.126.1,
>      host= 129.119.126.126, domain=seas.smu.edu, nis-domain=(none),
>      bootserver=129.119.113.107, rootserver=129.119.124.64 , rootpath=<7>
> evbug.c: Event. Dev: <NULL>, Type: 1, Code: 184, Value: 2
> Looking up port of RPC 100003/2 on 129.119.124.64
> Looking up port of RPC 100005/1 on 129.119.124.64
> VFS: Mounted root (nfs filesystem).
> Mounted devfs on /dev
> Freeing init memory: 104K
> init started:  BusyBox v1.00-pre8 (2004.03.05-22:18+0000) multi-call binary
>
> ******************************************
> Starting System Init for innovator
> ******************************************
>
> Please press Enter to activate this console.
>
>
> The target board has a root file system that is NFS mounted from the host
> pc. 
The file system is the host machine. Put the "Helloworld" in the 
directory exported by NFS.  :)

> I tried to run a simple c program " Helloworld.c" from the H2 board. For
> this I cross compiled the source code using snapgear toolchain. This
> generated an executable "Helloworld". I dont know how to load this
> executable into the H2 board. Kindly help me in this regard.
>
> Thanking you in advance,
> Phanee
> _______________________________________________
> Linux-omap-open-source mailing list
> Linux-omap-open-source@linux.omap.com
> http://linux.omap.com/mailman/listinfo/linux-omap-open-source
>
>   


-- 
Francisco Keppler Silva Alecrim
INdT - OSMRC - Manaus
Core team

Tel   : (+55 92) 2126 1017
Mobile: (+55 92) 9198 4214
Skype : keppleralecrim
Jabber: alecrim@gmail.com