From mboxrd@z Thu Jan 1 00:00:00 1970 From: Josh Karabin Subject: Re: About to tag v2.6.26-omap1, patch queue deleted, please check and repost Date: Wed, 06 Aug 2008 17:31:13 -0400 Message-ID: <489A1821.6080300@vocollect.com> References: <20080805143519.GS7193@atomide.com> <5A47E75E594F054BAF48C5E4FC4B92AB02569B8A85@dbde02.ent.ti.com> <489897CD.6040802@googlemail.com> Mime-Version: 1.0 Content-Type: text/plain; charset=UTF-8; format=flowed Content-Transfer-Encoding: QUOTED-PRINTABLE Return-path: Received: from mx4.vocollect.com ([64.212.175.114]:3076 "EHLO mx4.vocollect.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1763473AbYHFVbP convert rfc822-to-8bit (ORCPT ); Wed, 6 Aug 2008 17:31:15 -0400 In-Reply-To: <489897CD.6040802@googlemail.com> Sender: linux-omap-owner@vger.kernel.org List-Id: linux-omap@vger.kernel.org To: Dirk Behme Cc: Tony Lindgren , "linux-omap@vger.kernel.org" On an omap3evm with the defconfig, the kernel is failing to identify a=20 jffs2 filesystem. It's booting from NFS just fine. I had built the latest code checked into linux-omap last week - file=20 system booting had been working, IIRC. Loading TI reference 2.6.22=20 kernel finds the file system just fine as well. I'll begin looking int= o=20 this next week if someone else doesn't beat me to it. ---- Texas Instruments X-Loader 1.41 Detected Samsung MuxOneNAND1G Flash Starting OS Bootloader... U-Boot 1.1.4 (Jun 6 2008 - 18:25:31) OMAP3-GP rev 2, CPU-OPP2 L3-165MHz OMAP3EVM 1.0 Version + mPOP (Boot ONND) DRAM: 128 MB OneNAND Manufacturer: Samsung (0xec) Muxed OneNAND 128MB 1.8V 16-bit (0x30) OneNAND version =3D 0x0221 Scanning device for bad blocks num of blocks =3D 2048 In: serial Out: serial Err: serial Reseting CHIP... Done LAN9x18 (0x01150002) detected. Setting mac address: 00:50:c2:7e:86:9f start Auto negotiation... (take ~2sec) Auto negotiation complete, 100BaseTX, full duplex Hit any key to stop autoboot: 0 OMAP3EVM # run boot_fs Done ## Booting image at 80000000 ... Image Name: Linux-2.6.26-omap1-04784-g040378 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1515692 Bytes =3D 1.4 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux............................................................. =2E.................................... done, booting the kernel. <5>Linux version 2.6.26-omap1-04784-g040378c-dirty (gkarabin@gkarabin-f9) (gcc v ersion 4.2.1 (CodeSourcery Sourcery G++ Lite 2007q3-51)) #3 Tue Aug 5 14:45:54 E DT 2008 CPU: ARMv7 Processor [411fc082] revision 2 (ARMv7), cr=3D00c5387f Machine: OMAP3 EVM Memory policy: ECC disabled, Data cache writeback <7>On node 0 totalpages: 32768 <7> DMA zone: 256 pages used for memmap <7> DMA zone: 0 pages reserved <7> DMA zone: 32512 pages, LIFO batch:7 <7> Normal zone: 0 pages used for memmap <7> Movable zone: 0 pages used for memmap <6>OMAP3430 ES2.2 <6>SRAM: Mapped pa 0x40200000 to va 0xd7000000 size: 0x100000 CPU0: D VIPT write-through cache CPU0: cache: 768 bytes, associativity 1, 8 byte lines, 64 sets Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 <5>Kernel command line: mem=3D128M console=3DttyS0,115200n8 noinitrd root=3D/dev/mtdbl ock4 rw rootfstype=3Djffs2 ip=3D10.51.0.10:10.51.0.30:10.2.8.1:255.255.252.0:omap-ev m0:eth0:on <6>Clocking rate (Crystal/DPLL/ARM core): 26.0/332/500 MHz <6>GPMC revision 5.0 <6>IRQ: Found an INTC at 0xd8200000 (revision 4.0) with 96 interrupts <6>Total of 96 interrupts on 1 active controller <6>OMAP34xx GPIO hardware version 2.5 PID hash table entries: 512 (order: 9, 2048 bytes) Console: colour dummy device 80x30 <6>Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) <6>Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) <6>Memory: 128MB =3D 128MB total <5>Memory: 126720KB available (2776K code, 230K data, 116K init) <7>Calibrating delay loop... 498.87 BogoMIPS (lpj=3D1945600) Mount-cache hash table entries: 512 <6>CPU: Testing write buffer coherency: ok <6>net_namespace: 192 bytes <6>NET: Registered protocol family 16 <4>Warning: L2 cache not enabled. Check your bootloader. L2 off results in perfo rmance loss <6>OMAP DMA hardware revision 4.0 <3>USB: No board-specific platform config found <6>i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz <6>i2c_omap i2c_omap.2: bus 2 rev3.12 at 400 kHz <6>i2c_omap i2c_omap.3: bus 3 rev3.12 at 400 kHz <6>TWL4030: TRY attach Slave TWL4030-ID0 on Adapter OMAP I2C adapter [1= ] <6>TWL4030: TRY attach Slave TWL4030-ID1 on Adapter OMAP I2C adapter [1= ] <6>TWL4030: TRY attach Slave TWL4030-ID2 on Adapter OMAP I2C adapter [1= ] <6>TWL4030: TRY attach Slave TWL4030-ID3 on Adapter OMAP I2C adapter [1= ] <6>Initialized TWL4030 USB module <5>SCSI subsystem initialized <6>NET: Registered protocol family 2 <7>Switched to high resolution mode on CPU 0 <6>IP route cache hash table entries: 1024 (order: 0, 4096 bytes) <6>TCP established hash table entries: 4096 (order: 3, 32768 bytes) <6>TCP bind hash table entries: 4096 (order: 2, 16384 bytes) <6>TCP: Hash tables configured (established 4096 bind 4096) <6>TCP reno registered <6>NET: Registered protocol family 1 <4>NetWinder Floating Point Emulator V0.97 (double precision) <5>VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>JFFS2 version 2.2. (NAND) =EF=BF=BD=C2=A9 2001-2006 Red Hat, Inc. <6>msgmni has been set to 247 <6>io scheduler noop registered <6>io scheduler anticipatory registered (default) <6>io scheduler deadline registered <6>io scheduler cfq registered <6>omapfb: configured for panel omap3evm <6>omapfb: DISPC version 3.0 initialized <6>omapfb: Framebuffer initialized. Total vram 614400 planes 1 <6>omapfb: Pixclock 24000 kHz hfreq 45.2 kHz vfreq 70.3 Hz <6>Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled <6>serial8250.0: ttyS0 at MMIO 0x4806a000 (irq =3D 72) is a ST16654 <6>console [ttyS0] enabled Linux version 2.6.26-omap1-04784-g040378c-dirty (gkarabin@gkarabin-f9) (gcc vers ion 4.2.1 (CodeSourcery Sourcery G++ Lite 2007q3-51)) #3 Tue Aug 5 14:45:54 EDT 2008 CPU: ARMv7 Processor [411fc082] revision 2 (ARMv7), cr=3D00c5387f Machine: OMAP3 EVM Memory policy: ECC disabled, Data cache writeback OMAP3430 ES2.2 SRAM: Mapped pa 0x40200000 to va 0xd7000000 size: 0x100000 CPU0: D VIPT write-through cache CPU0: cache: 768 bytes, associativity 1, 8 byte lines, 64 sets Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: mem=3D128M console=3DttyS0,115200n8 noinitrd root=3D/dev/mtdblock 4 rw rootfstype=3Djffs2 ip=3D10.51.0.10:10.51.0.30:10.2.8.1:255.255.252.0:omap-evm0: eth0:on Clocking rate (Crystal/DPLL/ARM core): 26.0/332/500 MHz GPMC revision 5.0 IRQ: Found an INTC at 0xd8200000 (revision 4.0) with 96 interrupts Total of 96 interrupts on 1 active controller OMAP34xx GPIO hardware version 2.5 PID hash table entries: 512 (order: 9, 2048 bytes) Console: colour dummy device 80x30 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 128MB =3D 128MB total Memory: 126720KB available (2776K code, 230K data, 116K init) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok net_namespace: 192 bytes NET: Registered protocol family 16 Warning: L2 cache not enabled. Check your bootloader. L2 off results in performa nce loss OMAP DMA hardware revision 4.0 USB: No board-specific platform config found i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz i2c_omap i2c_omap.2: bus 2 rev3.12 at 400 kHz i2c_omap i2c_omap.3: bus 3 rev3.12 at 400 kHz TWL4030: TRY attach Slave TWL4030-ID0 on Adapter OMAP I2C adapter [1] TWL4030: TRY attach Slave TWL4030-ID1 on Adapter OMAP I2C adapter [1] TWL4030: TRY attach Slave TWL4030-ID2 on Adapter OMAP I2C adapter [1] TWL4030: TRY attach Slave TWL4030-ID3 on Adapter OMAP I2C adapter [1] Initialized TWL4030 USB module SCSI subsystem initialized NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 NetWinder Floating Point Emulator V0.97 (double precision) VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) JFFS2 version 2.2. (NAND) =EF=BF=BD=C2=A9 2001-2006 Red Hat, Inc. msgmni has been set to 247 io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered omapfb: configured for panel omap3evm omapfb: DISPC version 3.0 initialized omapfb: Framebuffer initialized. Total vram 614400 planes 1 omapfb: Pixclock 24000 kHz hfreq 45.2 kHz vfreq 70.3 Hz Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enable= d serial8250.0: ttyS0 at MMIO 0x4806a000 (irq =3D 72) is a ST16654 console [ttyS0] enabled <6>serial8250.0: ttyS1 at MMIO 0x4806c000 (irq =3D 73) is a ST16654 serial8250.0: ttyS1 at MMIO 0x4806c000 (irq =3D 73) is a ST16654 <6>serial8250.0: ttyS2 at MMIO 0x49020000 (irq =3D 74) is a ST16654 serial8250.0: ttyS2 at MMIO 0x49020000 (irq =3D 74) is a ST16654 <6>brd: module loaded brd: module loaded <6>loop: module loaded loop: module loaded eth0: LAN9115 (rev 2) at 0xc8850000 IRQ 336eth0: LAN9115 (rev 2) at 0xc8850000 I RQ 336 eth0: Ethernet addr: eth0: Ethernet addr: 00:00:50:50:c2:c2:7e:7e:86:86:9f 9f <7>eth0: LAN911x Internal PHY <6>i2c /dev entries driver i2c /dev entries driver <6>TWL4030 GPIO Demux: IRQ Range 384 to 402, Initialization Success TWL4030 GPIO Demux: IRQ Range 384 to 402, Initialization Success <4>Driver 'sd' needs updating - please use bus_type methods Driver 'sd' needs updating - please use bus_type methods <6>OMAP2 OneNAND driver initializing OMAP2 OneNAND driver initializing <6>omap2-onenand omap2-onenand: initializing on CS0, phys base 0x20000000, virtu al base c8880000 omap2-onenand omap2-onenand: initializing on CS0, phys base 0x20000000, virtual base c8880000 <7>OneNAND Manufacturer: Samsung (0xec) <6>Muxed OneNAND 128MB 1.8V 16-bit (0x30) Muxed OneNAND 128MB 1.8V 16-bit (0x30) <6>OneNAND version =3D 0x0221 OneNAND version =3D 0x0221 <7>Chip support all block unlock <6>Scanning device for bad blocks Scanning device for bad blocks <6>TCP cubic registered TCP cubic registered <6>NET: Registered protocol family 17 NET: Registered protocol family 17 <6>NET: Registered protocol family 15 NET: Registered protocol family 15 <6>RPC: Registered udp transport module. RPC: Registered udp transport module. <6>RPC: Registered tcp transport module. RPC: Registered tcp transport module. <3>Power Management for TI OMAP3. Power Management for TI OMAP3. <6>VFP support v0.3: VFP support v0.3: implementor 41 architecture 3 part 30 var iant c rev 1 implementor 41 architecture 3 part 30 variant c rev 1 <6>eth0: link down eth0: link down <3>IP-Config: Gateway not on directly connected network. IP-Config: Gateway not on directly connected network. <5>Looking up port of RPC 100003/2 on 10.51.0.30 Looking up port of RPC 100003/2 on 10.51.0.30 <6>eth0: link up, 100Mbps, full-duplex, lpa 0x03E1 eth0: link up, 100Mbps, full-duplex, lpa 0x03E1 <5>Looking up port of RPC 100005/1 on 10.51.0.30 Looking up port of RPC 100005/1 on 10.51.0.30 <3>Root-NFS: Server returned error -13 while mounting /tftpboot/omap-evm0 Root-NFS: Server returned error -13 while mounting /tftpboot/omap-evm0 <3>VFS: Unable to mount root fs via NFS, trying floppy. VFS: Unable to mount root fs via NFS, trying floppy. List of all partitions: List of all partitions: No filesystem could mount root, tried: No filesystem could mount root, tried: j ffs2 jffs2 <0>Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0 ) Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0) Dirk Behme wrote: >=20 > Gadiyar, Anand wrote: >>> Hi all, >>> >>> I've pushed all the patches I have in my omap inbox, except for >>> the omap serial driver that I want to look more. >>> >>> I've tried to comment on the ones that did not get pushed, then >>> erased everything from my omap inbox. Some drivers should get >>> integrated via other mailing lists, and some debug patches can >>> probably stay as debug patches, and some patches I probably >>> have accidentally deleted :) And the PM patches I lost track of, >>> so those should be reposted. >>> >>> So please check your patches, and repost your patches if something >>> is left out. Also please check that things work for your board, >>> let's try to tag v2.6.26-omap1 within next few days so we can >>> move on again. >>> >>> Cheers, >>> >>> Tony >> >> >> Boot tested on 3430SDP with the defconfig. Things work okay so far. >=20 > Same with BeagleBoard. >=20 > Dirk >=20 > --=20 > To unsubscribe from this list: send the line "unsubscribe linux-omap"= in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-omap" i= n the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html