* [PATCH 0/8] RFC: introduce 3630 boards @ 2009-11-03 21:20 Vikram Pandita 2009-11-03 21:20 ` [PATCH 1/8] omap: 3630: update is_chip variable Vikram Pandita 2009-11-03 21:23 ` [PATCH 0/8] RFC: introduce 3630 boards Pandita, Vikram 0 siblings, 2 replies; 16+ messages in thread From: Vikram Pandita @ 2009-11-03 21:20 UTC (permalink / raw) To: linux-omap; +Cc: Vikram Pandita Introducing 3630 boards: zoom3 and sdp3630 The peripherals are very similar for the two bards as per this discussion: http://marc.info/?l=linux-omap&m=125676595710748&w=2 So maximum reuse is done for the board files for zoom3 and sdp3630 Review comments incorporated: http://marc.info/?l=linux-omap&m=125632676504364&w=2 http://marc.info/?l=linux-omap&m=125632720804869&w=2 http://marc.info/?l=linux-omap&m=125633994320138&w=2 Vikram Pandita (8): omap: 3630: update is_chip variable omap: DEBUG_LL: allow no omap uart configuration omap: zoom2: split baord file for reuse omap: zoom2: update defconfig omap: zoom3: introduce zoom3 board support omap: zoom3: defconfig creation omap: 3630sdp: introduce 3630 sdp board support omap: 3630sdp: defconfig creation arch/arm/configs/omap_3630sdp_defconfig | 1606 ++++++++++++++++++++ arch/arm/configs/omap_zoom2_defconfig | 231 ++-- arch/arm/configs/omap_zoom3_defconfig | 1605 +++++++++++++++++++ arch/arm/mach-omap2/Kconfig | 8 + arch/arm/mach-omap2/Makefile | 8 + arch/arm/mach-omap2/board-3630sdp.c | 96 ++ arch/arm/mach-omap2/board-zoom-peripherals.c | 414 +++++ arch/arm/mach-omap2/board-zoom2.c | 261 +--- arch/arm/mach-omap2/board-zoom3.c | 59 + arch/arm/mach-omap2/id.c | 2 + arch/arm/mach-omap2/sdram-hynix-h8mbx00u0mer-0em.h | 54 + arch/arm/plat-omap/Kconfig | 3 + arch/arm/plat-omap/include/plat/cpu.h | 7 +- arch/arm/plat-omap/include/plat/uncompress.h | 4 +- 14 files changed, 4018 insertions(+), 340 deletions(-) create mode 100644 arch/arm/configs/omap_3630sdp_defconfig create mode 100644 arch/arm/configs/omap_zoom3_defconfig create mode 100755 arch/arm/mach-omap2/board-3630sdp.c create mode 100755 arch/arm/mach-omap2/board-zoom-peripherals.c mode change 100644 => 100755 arch/arm/mach-omap2/board-zoom2.c create mode 100755 arch/arm/mach-omap2/board-zoom3.c create mode 100644 arch/arm/mach-omap2/sdram-hynix-h8mbx00u0mer-0em.h ^ permalink raw reply [flat|nested] 16+ messages in thread
* [PATCH 1/8] omap: 3630: update is_chip variable 2009-11-03 21:20 [PATCH 0/8] RFC: introduce 3630 boards Vikram Pandita @ 2009-11-03 21:20 ` Vikram Pandita 2009-11-03 21:20 ` [PATCH 2/8] omap: DEBUG_LL: allow no omap uart configuration Vikram Pandita 2009-11-03 21:23 ` [PATCH 0/8] RFC: introduce 3630 boards Pandita, Vikram 1 sibling, 1 reply; 16+ messages in thread From: Vikram Pandita @ 2009-11-03 21:20 UTC (permalink / raw) To: linux-omap; +Cc: Vikram Pandita 3630 is getting treated like next rev of 3430 omap_chip.oc variable has to be updated for 3630 version Otherwise the Core power domain is not getting registered. This gets used in the registration of power domains in: "arch/arm/mach-omap2/powerdomains34xx.h" core_34xx_es3_1_pwrdm OMAP_CHIP_INIT(CHIP_GE_OMAP3430ES3_1) Core power doman will get registered for 3630 only when .oc is pouplated correctly. Tested on Zoom3(3630) board Signed-off-by: Vikram Pandita <vikram.pandita@ti.com> Acked-by: Alexander Shishkin <virtuoso@slind.org> Acked-by: Ari Kauppi <kauppi@papupata.org> --- arch/arm/mach-omap2/id.c | 2 ++ arch/arm/plat-omap/include/plat/cpu.h | 7 +++++-- 2 files changed, 7 insertions(+), 2 deletions(-) diff --git a/arch/arm/mach-omap2/id.c b/arch/arm/mach-omap2/id.c index 1c15112..189cf7a 100644 --- a/arch/arm/mach-omap2/id.c +++ b/arch/arm/mach-omap2/id.c @@ -359,6 +359,8 @@ void __init omap2_check_revision(void) omap_chip.oc |= CHIP_IS_OMAP3430ES3_0; else if (omap_rev() == OMAP3430_REV_ES3_1) omap_chip.oc |= CHIP_IS_OMAP3430ES3_1; + else if (omap_rev() == OMAP3630_REV_ES1_0) + omap_chip.oc |= CHIP_IS_OMAP3630ES1; } else { pr_err("Uninitialized omap_chip, please fix!\n"); } diff --git a/arch/arm/plat-omap/include/plat/cpu.h b/arch/arm/plat-omap/include/plat/cpu.h index 7cb0556..05a0a33 100644 --- a/arch/arm/plat-omap/include/plat/cpu.h +++ b/arch/arm/plat-omap/include/plat/cpu.h @@ -454,6 +454,7 @@ IS_OMAP_TYPE(3430, 0x3430) #define CHIP_IS_OMAP3430ES2 (1 << 4) #define CHIP_IS_OMAP3430ES3_0 (1 << 5) #define CHIP_IS_OMAP3430ES3_1 (1 << 6) +#define CHIP_IS_OMAP3630ES1 (1 << 7) #define CHIP_IS_OMAP24XX (CHIP_IS_OMAP2420 | CHIP_IS_OMAP2430) @@ -465,8 +466,10 @@ IS_OMAP_TYPE(3430, 0x3430) */ #define CHIP_GE_OMAP3430ES2 (CHIP_IS_OMAP3430ES2 | \ CHIP_IS_OMAP3430ES3_0 | \ - CHIP_IS_OMAP3430ES3_1) -#define CHIP_GE_OMAP3430ES3_1 (CHIP_IS_OMAP3430ES3_1) + CHIP_IS_OMAP3430ES3_1 | \ + CHIP_IS_OMAP3630ES1) +#define CHIP_GE_OMAP3430ES3_1 (CHIP_IS_OMAP3430ES3_1 | \ + CHIP_IS_OMAP3630ES1) int omap_chip_is(struct omap_chip_id oci); -- 1.6.5.1.69.g36942 ^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH 2/8] omap: DEBUG_LL: allow no omap uart configuration 2009-11-03 21:20 ` [PATCH 1/8] omap: 3630: update is_chip variable Vikram Pandita @ 2009-11-03 21:20 ` Vikram Pandita 2009-11-03 21:20 ` [PATCH 3/8] omap: zoom2: split baord file for reuse Vikram Pandita 2009-11-03 22:09 ` [PATCH 2/8] omap: DEBUG_LL: allow no omap uart configuration Nishanth Menon 0 siblings, 2 replies; 16+ messages in thread From: Vikram Pandita @ 2009-11-03 21:20 UTC (permalink / raw) To: linux-omap; +Cc: Vikram Pandita Zoom2/Zoom3 kind of boards do not use omap uarts these boards should not have DEBUG_LL writing to omap uarts Signed-off-by: Vikram Pandita <vikram.pandita@ti.com> --- arch/arm/plat-omap/Kconfig | 3 +++ arch/arm/plat-omap/include/plat/uncompress.h | 4 +++- 2 files changed, 6 insertions(+), 1 deletions(-) diff --git a/arch/arm/plat-omap/Kconfig b/arch/arm/plat-omap/Kconfig index 64b3f52..c912e0e 100644 --- a/arch/arm/plat-omap/Kconfig +++ b/arch/arm/plat-omap/Kconfig @@ -176,6 +176,9 @@ config OMAP_LL_DEBUG_UART2 config OMAP_LL_DEBUG_UART3 bool "UART3" +config OMAP_LL_DEBUG_NONE + bool "None" + endchoice config OMAP_SERIAL_WAKE diff --git a/arch/arm/plat-omap/include/plat/uncompress.h b/arch/arm/plat-omap/include/plat/uncompress.h index e22f575..49b38f0 100644 --- a/arch/arm/plat-omap/include/plat/uncompress.h +++ b/arch/arm/plat-omap/include/plat/uncompress.h @@ -44,8 +44,10 @@ static void putc(int c) uart = (volatile u8 *)(OMAP_UART3_BASE); #elif defined(CONFIG_OMAP_LL_DEBUG_UART2) uart = (volatile u8 *)(OMAP_UART2_BASE); -#else +#elif defined(CONFIG_OMAP_LL_DEBUG_UART1) uart = (volatile u8 *)(OMAP_UART1_BASE); +#elif defined(CONFIG_OMAP_LL_DEBUG_NONE) + return; #endif #ifdef CONFIG_ARCH_OMAP1 -- 1.6.5.1.69.g36942 ^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH 3/8] omap: zoom2: split baord file for reuse 2009-11-03 21:20 ` [PATCH 2/8] omap: DEBUG_LL: allow no omap uart configuration Vikram Pandita @ 2009-11-03 21:20 ` Vikram Pandita 2009-11-03 21:20 ` [PATCH 4/8] omap: zoom2: update defconfig Vikram Pandita 2009-11-03 22:17 ` [PATCH 3/8] omap: zoom2: split baord file for reuse Nishanth Menon 2009-11-03 22:09 ` [PATCH 2/8] omap: DEBUG_LL: allow no omap uart configuration Nishanth Menon 1 sibling, 2 replies; 16+ messages in thread From: Vikram Pandita @ 2009-11-03 21:20 UTC (permalink / raw) To: linux-omap; +Cc: Vikram Pandita, Vikram Pandita Split zoom2 board file into: base board file and a board-zoom-peripherals.c file that way the same peripherals file can be reused for: zoom3 and sdp3630 Signed-off-by: Vikram Pandita <vikram.pandtia@ti.com> --- arch/arm/mach-omap2/Makefile | 1 + arch/arm/mach-omap2/board-zoom-peripherals.c | 414 ++++++++++++++++++++++++++ arch/arm/mach-omap2/board-zoom2.c | 261 +--------------- 3 files changed, 429 insertions(+), 247 deletions(-) create mode 100755 arch/arm/mach-omap2/board-zoom-peripherals.c mode change 100644 => 100755 arch/arm/mach-omap2/board-zoom2.c diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index 03cb4fc..4d66b42 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -72,6 +72,7 @@ obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51.o \ board-rx51-peripherals.o \ mmc-twl4030.o obj-$(CONFIG_MACH_OMAP_ZOOM2) += board-zoom2.o \ + board-zoom-peripherals.o \ mmc-twl4030.o \ board-zoom-debugboard.o obj-$(CONFIG_MACH_CM_T35) += board-cm-t35.o \ diff --git a/arch/arm/mach-omap2/board-zoom-peripherals.c b/arch/arm/mach-omap2/board-zoom-peripherals.c new file mode 100755 index 0000000..c799eca --- /dev/null +++ b/arch/arm/mach-omap2/board-zoom-peripherals.c @@ -0,0 +1,414 @@ +/* + * Copyright (C) 2009 Texas Instruments Inc. + * + * Modified from mach-omap2/board-ldp.c + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/input.h> +#include <linux/input/matrix_keypad.h> +#include <linux/gpio.h> +#include <linux/i2c/twl4030.h> +#include <linux/regulator/machine.h> + +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <asm/mach/map.h> + +#include <plat/common.h> +#include <plat/usb.h> + +#include "mmc-twl4030.h" + +/* Zoom2 has Qwerty keyboard*/ +static int board_keymap[] = { + KEY(0, 0, KEY_E), + KEY(1, 0, KEY_R), + KEY(2, 0, KEY_T), + KEY(3, 0, KEY_HOME), + KEY(6, 0, KEY_I), + KEY(7, 0, KEY_LEFTSHIFT), + KEY(0, 1, KEY_D), + KEY(1, 1, KEY_F), + KEY(2, 1, KEY_G), + KEY(3, 1, KEY_SEND), + KEY(6, 1, KEY_K), + KEY(7, 1, KEY_ENTER), + KEY(0, 2, KEY_X), + KEY(1, 2, KEY_C), + KEY(2, 2, KEY_V), + KEY(3, 2, KEY_END), + KEY(6, 2, KEY_DOT), + KEY(7, 2, KEY_CAPSLOCK), + KEY(0, 3, KEY_Z), + KEY(1, 3, KEY_KPPLUS), + KEY(2, 3, KEY_B), + KEY(3, 3, KEY_F1), + KEY(6, 3, KEY_O), + KEY(7, 3, KEY_SPACE), + KEY(0, 4, KEY_W), + KEY(1, 4, KEY_Y), + KEY(2, 4, KEY_U), + KEY(3, 4, KEY_F2), + KEY(4, 4, KEY_VOLUMEUP), + KEY(6, 4, KEY_L), + KEY(7, 4, KEY_LEFT), + KEY(0, 5, KEY_S), + KEY(1, 5, KEY_H), + KEY(2, 5, KEY_J), + KEY(3, 5, KEY_F3), + KEY(5, 5, KEY_VOLUMEDOWN), + KEY(6, 5, KEY_M), + KEY(4, 5, KEY_ENTER), + KEY(7, 5, KEY_RIGHT), + KEY(0, 6, KEY_Q), + KEY(1, 6, KEY_A), + KEY(2, 6, KEY_N), + KEY(3, 6, KEY_BACKSPACE), + KEY(6, 6, KEY_P), + KEY(7, 6, KEY_UP), + KEY(6, 7, KEY_SELECT), + KEY(7, 7, KEY_DOWN), + KEY(0, 7, KEY_PROG1), /*MACRO 1 <User defined> */ + KEY(1, 7, KEY_PROG2), /*MACRO 2 <User defined> */ + KEY(2, 7, KEY_PROG3), /*MACRO 3 <User defined> */ + KEY(3, 7, KEY_PROG4), /*MACRO 4 <User defined> */ + 0 +}; + +static struct matrix_keymap_data board_map_data = { + .keymap = board_keymap, + .keymap_size = ARRAY_SIZE(board_keymap), +}; + +static struct twl4030_keypad_data zoom_kp_twl4030_data = { + .keymap_data = &board_map_data, + .rows = 8, + .cols = 8, + .rep = 1, +}; + +static struct twl4030_madc_platform_data zoom_madc_data = { + .irq_line = 1, +}; + +static struct twl4030_hsmmc_info mmc[] = { + { + .name = "external", + .mmc = 1, + .wires = 4, + .cover_only = true, + .gpio_cd = -EINVAL, + .gpio_wp = -EINVAL, + .power_saving = true, + }, + { + .name = "internal", + .mmc = 2, + .wires = 8, + .gpio_cd = -EINVAL, + .gpio_wp = -EINVAL, + .nonremovable = true, + .power_saving = true, + }, + {} /* Terminator */ +}; + +static struct regulator_consumer_supply zoom_vmmc1_supply = { + .supply = "vmmc", +}; + +static struct regulator_consumer_supply zoom_vmmc2_supply = { + .supply = "vmmc", +}; + +static struct regulator_consumer_supply zoom_vsim_supply = { + .supply = "vmmc_aux", +}; + +/* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */ +static struct regulator_init_data zoom_vmmc1 = { + .constraints = { + .min_uV = 1850000, + .max_uV = 3150000, + .valid_modes_mask = REGULATOR_MODE_NORMAL + | REGULATOR_MODE_STANDBY, + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE + | REGULATOR_CHANGE_MODE + | REGULATOR_CHANGE_STATUS, + }, + .num_consumer_supplies = 1, + .consumer_supplies = &zoom_vmmc1_supply, +}; + +/* VMMC2 for MMC2 card */ +static struct regulator_init_data zoom_vmmc2 = { + .constraints = { + .name = "VMMC2_30", + .min_uV = 1850000, + .max_uV = 1850000, + .apply_uV = true, + .valid_modes_mask = REGULATOR_MODE_NORMAL + | REGULATOR_MODE_STANDBY, + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE + | REGULATOR_CHANGE_MODE + | REGULATOR_CHANGE_STATUS, + }, + .num_consumer_supplies = 1, + .consumer_supplies = &zoom_vmmc2_supply, +}; + +/* VSIM for OMAP VDD_MMC1A (i/o for DAT4..DAT7) */ +static struct regulator_init_data zoom_vsim = { + .constraints = { + .name = "VMMC2_IO_18", + .min_uV = 1800000, + .max_uV = 3000000, + .apply_uV = true, + .valid_modes_mask = REGULATOR_MODE_NORMAL + | REGULATOR_MODE_STANDBY, + .valid_ops_mask = REGULATOR_CHANGE_MODE + | REGULATOR_CHANGE_STATUS, + }, + .num_consumer_supplies = 1, + .consumer_supplies = &zoom_vsim_supply, +}; + +static int zoom_twl_gpio_setup(struct device *dev, + unsigned gpio, unsigned ngpio) +{ + /* gpio + 0 is "mmc0_cd" (input/IRQ), + * gpio + 1 is "mmc1_cd" (input/IRQ) + */ + mmc[0].gpio_cd = gpio + 0; + mmc[1].gpio_cd = gpio + 1; + twl4030_mmc_init(mmc); + + /* link regulators to MMC adapters ... we "know" the + * regulators will be set up only *after* we return. + */ + zoom_vmmc1_supply.dev = mmc[0].dev; + zoom_vmmc2_supply.dev = mmc[1].dev; + zoom_vsim_supply.dev = mmc[0].dev; + + return 0; +} + +//static struct twl4030_gpio_platform_data zoom_gpio_data = { +// .gpio_base = OMAP_MAX_GPIO_LINES, +// .irq_base = TWL4030_GPIO_IRQ_BASE, +// .irq_end = TWL4030_GPIO_IRQ_END, +// .pulldowns = BIT(0) | BIT(1) | BIT(2) | BIT(3) +// | BIT(4) | BIT(5) +// | BIT(8) | BIT(9) | BIT(10) | BIT(11) +// | BIT(12) | BIT(13) | BIT(14) | BIT(15) +// | BIT(16) | BIT(17) , +// .setup = zoom_twlgpio_setup, +//}; +static struct twl4030_gpio_platform_data zoom_gpio_data = { + .gpio_base = OMAP_MAX_GPIO_LINES, + .irq_base = TWL4030_GPIO_IRQ_BASE, + .irq_end = TWL4030_GPIO_IRQ_END, + .setup = zoom_twl_gpio_setup, +}; + +static struct twl4030_usb_data zoom_usb_data = { + .usb_mode = T2_USB_MODE_ULPI, +}; + +/* TODO: enable T2 scripts */ +#if 0 +static struct twl4030_ins sleep_on_seq[] __initdata = { +/* + * Turn off VDD1 and VDD2. + */ + {MSG_SINGULAR(DEV_GRP_P1, 0xf, RES_STATE_OFF), 4}, + {MSG_SINGULAR(DEV_GRP_P1, 0x10, RES_STATE_OFF), 2}, +/* + * And also turn off the OMAP3 PLLs and the sysclk output. + */ + {MSG_SINGULAR(DEV_GRP_P1, 0x7, RES_STATE_OFF), 3}, + {MSG_SINGULAR(DEV_GRP_P1, 0x17, RES_STATE_OFF), 3}, +}; + +static struct twl4030_script sleep_on_script __initdata = { + .script = sleep_on_seq, + .size = ARRAY_SIZE(sleep_on_seq), + .flags = TWL4030_SLEEP_SCRIPT, +}; + +static struct twl4030_ins wakeup_seq[] __initdata = { +/* + * Reenable the OMAP3 PLLs. + * Wakeup VDD1 and VDD2. + * Reenable sysclk output. + */ + {MSG_SINGULAR(DEV_GRP_P1, 0x7, RES_STATE_ACTIVE), 0x30}, + {MSG_SINGULAR(DEV_GRP_P1, 0xf, RES_STATE_ACTIVE), 0x30}, + {MSG_SINGULAR(DEV_GRP_P1, 0x10, RES_STATE_ACTIVE), 0x37}, + {MSG_SINGULAR(DEV_GRP_P1, 0x19, RES_STATE_ACTIVE), 3}, +}; + +static struct twl4030_script wakeup_script __initdata = { + .script = wakeup_seq, + .size = ARRAY_SIZE(wakeup_seq), + .flags = TWL4030_WAKEUP12_SCRIPT, +}; + +static struct twl4030_ins wakeup_p3_seq[] __initdata = { +/* + * Wakeup VDD1 (dummy to be able to insert a delay) + * Enable CLKEN + */ + {MSG_SINGULAR(DEV_GRP_P1, 0x17, RES_STATE_ACTIVE), 3}, +}; + +static struct twl4030_script wakeup_p3_script __initdata = { + .script = wakeup_p3_seq, + .size = ARRAY_SIZE(wakeup_p3_seq), + .flags = TWL4030_WAKEUP3_SCRIPT, +}; + +static struct twl4030_ins wrst_seq[] __initdata = { +/* + * Reset twl4030. + * Reset VDD1 regulator. + * Reset VDD2 regulator. + * Reset VPLL1 regulator. + * Enable sysclk output. + * Reenable twl4030. + */ + {MSG_SINGULAR(DEV_GRP_NULL, RES_RESET, RES_STATE_OFF), 2}, + {MSG_BROADCAST(DEV_GRP_NULL, RES_GRP_ALL, 0, 1, RES_STATE_ACTIVE), + 0x13}, + {MSG_BROADCAST(DEV_GRP_NULL, RES_GRP_PP, 0, 2, RES_STATE_WRST), 0x13}, + {MSG_BROADCAST(DEV_GRP_NULL, RES_GRP_PP, 0, 3, RES_STATE_OFF), 0x13}, + {MSG_SINGULAR(DEV_GRP_NULL, RES_VDD1, RES_STATE_WRST), 0x13}, + {MSG_SINGULAR(DEV_GRP_NULL, RES_VDD2, RES_STATE_WRST), 0x13}, + {MSG_SINGULAR(DEV_GRP_NULL, RES_VPLL1, RES_STATE_WRST), 0x35}, + {MSG_SINGULAR(DEV_GRP_P1, RES_HFCLKOUT, RES_STATE_ACTIVE), 2}, + {MSG_SINGULAR(DEV_GRP_NULL, RES_RESET, RES_STATE_ACTIVE), 2}, +}; + +static struct twl4030_script wrst_script __initdata = { + .script = wrst_seq, + .size = ARRAY_SIZE(wrst_seq), + .flags = TWL4030_WRST_SCRIPT, +}; + +static struct twl4030_script *twl4030_scripts[] __initdata = { + /* wakeup12 script should be loaded before sleep script, otherwise a + board might hit retention before loading of wakeup script is + completed. This can cause boot failures depending on timing issues. + */ + &wakeup_script, + &sleep_on_script, + &wakeup_p3_script, + &wrst_script, +}; + +static struct twl4030_resconfig twl4030_rconfig[] __initdata = { + { .resource = RES_VINTANA1, .devgroup = -1, .type = -1, .type2 = 1 }, + { .resource = RES_VINTANA2, .devgroup = -1, .type = -1, .type2 = 1 }, + { .resource = RES_VINTDIG, .devgroup = -1, .type = -1, .type2 = 1 }, + { .resource = RES_VMMC1, .devgroup = -1, .type = -1, .type2 = 3}, + { .resource = RES_VMMC2, .devgroup = DEV_GRP_NULL, .type = -1, + .type2 = 3}, + { .resource = RES_VAUX1, .devgroup = -1, .type = -1, .type2 = 3}, + { .resource = RES_VAUX2, .devgroup = -1, .type = -1, .type2 = 3}, + { .resource = RES_VAUX3, .devgroup = -1, .type = -1, .type2 = 3}, + { .resource = RES_VAUX4, .devgroup = -1, .type = -1, .type2 = 3}, + { .resource = RES_VPLL2, .devgroup = -1, .type = -1, .type2 = 3}, + { .resource = RES_VDAC, .devgroup = -1, .type = -1, .type2 = 3}, + { .resource = RES_VSIM, .devgroup = DEV_GRP_NULL, .type = -1, + .type2 = 3}, + { .resource = RES_CLKEN, .devgroup = DEV_GRP_P3, .type = -1, + .type2 = 1 }, + { 0, 0}, +}; + +static struct twl4030_power_data zoom_t2scripts_data __initdata = { + .scripts = twl4030_scripts, + .num = ARRAY_SIZE(twl4030_scripts), + .resource_config = twl4030_rconfig, +}; +#endif + +static int zoom_batt_table[] = { +/* 0 C*/ +30800, 29500, 28300, 27100, +26000, 24900, 23900, 22900, 22000, 21100, 20300, 19400, 18700, 17900, +17200, 16500, 15900, 15300, 14700, 14100, 13600, 13100, 12600, 12100, +11600, 11200, 10800, 10400, 10000, 9630, 9280, 8950, 8620, 8310, +8020, 7730, 7460, 7200, 6950, 6710, 6470, 6250, 6040, 5830, +5640, 5450, 5260, 5090, 4920, 4760, 4600, 4450, 4310, 4170, +4040, 3910, 3790, 3670, 3550 +}; + +static struct twl4030_bci_platform_data zoom_bci_data = { + .battery_tmp_tbl = zoom_batt_table, + .tblsize = ARRAY_SIZE(zoom_batt_table), +}; + + +static struct twl4030_platform_data zoom_twldata = { + .irq_base = TWL4030_IRQ_BASE, + .irq_end = TWL4030_IRQ_END, + + /* platform_data for children goes here */ + .bci = &zoom_bci_data, + .madc = &zoom_madc_data, + .usb = &zoom_usb_data, + .gpio = &zoom_gpio_data, + .keypad = &zoom_kp_twl4030_data, + /* .power = &zoom_t2scripts_data,*/ + .vmmc1 = &zoom_vmmc1, + .vmmc2 = &zoom_vmmc2, + /* .vaux1 = &zoom_vaux1,*/ + /* .vaux2 = &zoom_vaux2,*/ + /* .vaux4 = &zoom_vaux4,*/ + .vsim = &zoom_vsim, + /* .vdac = &zoom_vdac,*/ +}; + +static struct i2c_board_info __initdata zoom_i2c_boardinfo[] = { + { + I2C_BOARD_INFO("twl5030", 0x48), + .flags = I2C_CLIENT_WAKE, + .irq = INT_34XX_SYS_NIRQ, + .platform_data = &zoom_twldata, + }, +}; + +static int __init zoom_i2c_init(void) +{ + omap_register_i2c_bus(1, 2200, zoom_i2c_boardinfo, + ARRAY_SIZE(zoom_i2c_boardinfo)); + + /* TODO: I2C2 on zoom2/3: + * Add Synaptic RMI controller + * Add Camera sensor IMX046 + * Add Camera sensor LV8093 + */ + omap_register_i2c_bus(2, 100, NULL, 0); + + /* TODO: I2C3 on Zoom2/3: + * Add: SIL9022 HDMI + */ + omap_register_i2c_bus(3, 100, NULL, 0); + return 0; +} + + +void __init zoom_peripherals_init(void) +{ + zoom_i2c_init(); + omap_serial_init(); + usb_musb_init(); +} diff --git a/arch/arm/mach-omap2/board-zoom2.c b/arch/arm/mach-omap2/board-zoom2.c old mode 100644 new mode 100755 index 4ad9b94..abcc1ae --- a/arch/arm/mach-omap2/board-zoom2.c +++ b/arch/arm/mach-omap2/board-zoom2.c @@ -1,8 +1,6 @@ /* * Copyright (C) 2009 Texas Instruments Inc. - * Mikkel Christensen <mlc@ti.com> * - * Modified from mach-omap2/board-ldp.c * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as @@ -13,280 +11,49 @@ #include <linux/init.h> #include <linux/platform_device.h> #include <linux/input.h> -#include <linux/input/matrix_keypad.h> #include <linux/gpio.h> -#include <linux/i2c/twl4030.h> -#include <linux/regulator/machine.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> #include <plat/common.h> -#include <plat/usb.h> +#include <plat/board.h> -#include "mmc-twl4030.h" #include "sdram-micron-mt46h32m32lf-6.h" -/* Zoom2 has Qwerty keyboard*/ -static int board_keymap[] = { - KEY(0, 0, KEY_E), - KEY(1, 0, KEY_R), - KEY(2, 0, KEY_T), - KEY(3, 0, KEY_HOME), - KEY(6, 0, KEY_I), - KEY(7, 0, KEY_LEFTSHIFT), - KEY(0, 1, KEY_D), - KEY(1, 1, KEY_F), - KEY(2, 1, KEY_G), - KEY(3, 1, KEY_SEND), - KEY(6, 1, KEY_K), - KEY(7, 1, KEY_ENTER), - KEY(0, 2, KEY_X), - KEY(1, 2, KEY_C), - KEY(2, 2, KEY_V), - KEY(3, 2, KEY_END), - KEY(6, 2, KEY_DOT), - KEY(7, 2, KEY_CAPSLOCK), - KEY(0, 3, KEY_Z), - KEY(1, 3, KEY_KPPLUS), - KEY(2, 3, KEY_B), - KEY(3, 3, KEY_F1), - KEY(6, 3, KEY_O), - KEY(7, 3, KEY_SPACE), - KEY(0, 4, KEY_W), - KEY(1, 4, KEY_Y), - KEY(2, 4, KEY_U), - KEY(3, 4, KEY_F2), - KEY(4, 4, KEY_VOLUMEUP), - KEY(6, 4, KEY_L), - KEY(7, 4, KEY_LEFT), - KEY(0, 5, KEY_S), - KEY(1, 5, KEY_H), - KEY(2, 5, KEY_J), - KEY(3, 5, KEY_F3), - KEY(5, 5, KEY_VOLUMEDOWN), - KEY(6, 5, KEY_M), - KEY(4, 5, KEY_ENTER), - KEY(7, 5, KEY_RIGHT), - KEY(0, 6, KEY_Q), - KEY(1, 6, KEY_A), - KEY(2, 6, KEY_N), - KEY(3, 6, KEY_BACKSPACE), - KEY(6, 6, KEY_P), - KEY(7, 6, KEY_UP), - KEY(6, 7, KEY_SELECT), - KEY(7, 7, KEY_DOWN), - KEY(0, 7, KEY_PROG1), /*MACRO 1 <User defined> */ - KEY(1, 7, KEY_PROG2), /*MACRO 2 <User defined> */ - KEY(2, 7, KEY_PROG3), /*MACRO 3 <User defined> */ - KEY(3, 7, KEY_PROG4), /*MACRO 4 <User defined> */ - 0 -}; - -static struct matrix_keymap_data board_map_data = { - .keymap = board_keymap, - .keymap_size = ARRAY_SIZE(board_keymap), -}; - -static struct twl4030_keypad_data zoom2_kp_twl4030_data = { - .keymap_data = &board_map_data, - .rows = 8, - .cols = 8, - .rep = 1, -}; - -static struct omap_board_config_kernel zoom2_config[] __initdata = { -}; - -static struct regulator_consumer_supply zoom2_vmmc1_supply = { - .supply = "vmmc", -}; - -static struct regulator_consumer_supply zoom2_vsim_supply = { - .supply = "vmmc_aux", -}; - -static struct regulator_consumer_supply zoom2_vmmc2_supply = { - .supply = "vmmc", -}; - -/* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */ -static struct regulator_init_data zoom2_vmmc1 = { - .constraints = { - .min_uV = 1850000, - .max_uV = 3150000, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE - | REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = 1, - .consumer_supplies = &zoom2_vmmc1_supply, -}; - -/* VMMC2 for MMC2 card */ -static struct regulator_init_data zoom2_vmmc2 = { - .constraints = { - .min_uV = 1850000, - .max_uV = 1850000, - .apply_uV = true, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = 1, - .consumer_supplies = &zoom2_vmmc2_supply, -}; - -/* VSIM for OMAP VDD_MMC1A (i/o for DAT4..DAT7) */ -static struct regulator_init_data zoom2_vsim = { - .constraints = { - .min_uV = 1800000, - .max_uV = 3000000, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE - | REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = 1, - .consumer_supplies = &zoom2_vsim_supply, -}; - -static struct twl4030_hsmmc_info mmc[] __initdata = { - { - .mmc = 1, - .wires = 4, - .gpio_wp = -EINVAL, - }, - { - .mmc = 2, - .wires = 4, - .gpio_wp = -EINVAL, - }, - {} /* Terminator */ -}; - -static int zoom2_twl_gpio_setup(struct device *dev, - unsigned gpio, unsigned ngpio) +static void __init omap_zoom_map_io(void) { - /* gpio + 0 is "mmc0_cd" (input/IRQ), - * gpio + 1 is "mmc1_cd" (input/IRQ) - */ - mmc[0].gpio_cd = gpio + 0; - mmc[1].gpio_cd = gpio + 1; - twl4030_mmc_init(mmc); - - /* link regulators to MMC adapters ... we "know" the - * regulators will be set up only *after* we return. - */ - zoom2_vmmc1_supply.dev = mmc[0].dev; - zoom2_vsim_supply.dev = mmc[0].dev; - zoom2_vmmc2_supply.dev = mmc[1].dev; - - return 0; + omap2_set_globals_343x(); + omap2_map_common_io(); } - -static int zoom2_batt_table[] = { -/* 0 C*/ -30800, 29500, 28300, 27100, -26000, 24900, 23900, 22900, 22000, 21100, 20300, 19400, 18700, 17900, -17200, 16500, 15900, 15300, 14700, 14100, 13600, 13100, 12600, 12100, -11600, 11200, 10800, 10400, 10000, 9630, 9280, 8950, 8620, 8310, -8020, 7730, 7460, 7200, 6950, 6710, 6470, 6250, 6040, 5830, -5640, 5450, 5260, 5090, 4920, 4760, 4600, 4450, 4310, 4170, -4040, 3910, 3790, 3670, 3550 -}; - -static struct twl4030_bci_platform_data zoom2_bci_data = { - .battery_tmp_tbl = zoom2_batt_table, - .tblsize = ARRAY_SIZE(zoom2_batt_table), +static struct omap_board_config_kernel zoom_config[] __initdata = { }; - -static struct twl4030_usb_data zoom2_usb_data = { - .usb_mode = T2_USB_MODE_ULPI, -}; - -static void __init omap_zoom2_init_irq(void) +static void __init omap_zoom_init_irq(void) { - omap_board_config = zoom2_config; - omap_board_config_size = ARRAY_SIZE(zoom2_config); + omap_board_config = zoom_config; + omap_board_config_size = ARRAY_SIZE(zoom_config); omap2_init_common_hw(mt46h32m32lf6_sdrc_params, mt46h32m32lf6_sdrc_params); omap_init_irq(); omap_gpio_init(); } -static struct twl4030_gpio_platform_data zoom2_gpio_data = { - .gpio_base = OMAP_MAX_GPIO_LINES, - .irq_base = TWL4030_GPIO_IRQ_BASE, - .irq_end = TWL4030_GPIO_IRQ_END, - .setup = zoom2_twl_gpio_setup, -}; - -static struct twl4030_madc_platform_data zoom2_madc_data = { - .irq_line = 1, -}; - -static struct twl4030_platform_data zoom2_twldata = { - .irq_base = TWL4030_IRQ_BASE, - .irq_end = TWL4030_IRQ_END, - - /* platform_data for children goes here */ - .bci = &zoom2_bci_data, - .madc = &zoom2_madc_data, - .usb = &zoom2_usb_data, - .gpio = &zoom2_gpio_data, - .keypad = &zoom2_kp_twl4030_data, - .vmmc1 = &zoom2_vmmc1, - .vmmc2 = &zoom2_vmmc2, - .vsim = &zoom2_vsim, - -}; - -static struct i2c_board_info __initdata zoom2_i2c_boardinfo[] = { - { - I2C_BOARD_INFO("twl4030", 0x48), - .flags = I2C_CLIENT_WAKE, - .irq = INT_34XX_SYS_NIRQ, - .platform_data = &zoom2_twldata, - }, -}; - -static int __init omap_i2c_init(void) -{ - omap_register_i2c_bus(1, 2600, zoom2_i2c_boardinfo, - ARRAY_SIZE(zoom2_i2c_boardinfo)); - omap_register_i2c_bus(2, 400, NULL, 0); - omap_register_i2c_bus(3, 400, NULL, 0); - return 0; -} - extern int __init omap_zoom2_debugboard_init(void); +extern void __init zoom_peripherals_init(void); -static void __init omap_zoom2_init(void) +static void __init omap_zoom_init(void) { - omap_i2c_init(); - omap_serial_init(); + zoom_peripherals_init(); omap_zoom2_debugboard_init(); - usb_musb_init(); -} - -static void __init omap_zoom2_map_io(void) -{ - omap2_set_globals_343x(); - omap2_map_common_io(); } MACHINE_START(OMAP_ZOOM2, "OMAP Zoom2 board") .phys_io = 0x48000000, .io_pg_offst = ((0xfa000000) >> 18) & 0xfffc, .boot_params = 0x80000100, - .map_io = omap_zoom2_map_io, - .init_irq = omap_zoom2_init_irq, - .init_machine = omap_zoom2_init, + .map_io = omap_zoom_map_io, + .init_irq = omap_zoom_init_irq, + .init_machine = omap_zoom_init, .timer = &omap_timer, MACHINE_END -- 1.6.5.1.69.g36942 ^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH 4/8] omap: zoom2: update defconfig 2009-11-03 21:20 ` [PATCH 3/8] omap: zoom2: split baord file for reuse Vikram Pandita @ 2009-11-03 21:20 ` Vikram Pandita 2009-11-03 21:20 ` [PATCH 5/8] omap: zoom3: introduce zoom3 board support Vikram Pandita 2009-11-04 7:09 ` [PATCH 4/8] omap: zoom2: update defconfig G, Manjunath Kondaiah 2009-11-03 22:17 ` [PATCH 3/8] omap: zoom2: split baord file for reuse Nishanth Menon 1 sibling, 2 replies; 16+ messages in thread From: Vikram Pandita @ 2009-11-03 21:20 UTC (permalink / raw) To: linux-omap; +Cc: Vikram Pandita Update DEBUG_LL for zoom2 board as CONFIG_OMAP_LL_DEBUG_NONE Sync zoom2 defconfig with menuconfig Signed-off-by: Vikram Pandita <vikram.pandita@ti.com> --- arch/arm/configs/omap_zoom2_defconfig | 231 ++++++++++++++++++++------------- 1 files changed, 141 insertions(+), 90 deletions(-) diff --git a/arch/arm/configs/omap_zoom2_defconfig b/arch/arm/configs/omap_zoom2_defconfig index f1739fa..db4fc1c 100644 --- a/arch/arm/configs/omap_zoom2_defconfig +++ b/arch/arm/configs/omap_zoom2_defconfig @@ -1,15 +1,13 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-omap1 -# Fri Jun 12 17:25:46 2009 +# Linux kernel version: 2.6.32-rc5 +# Tue Nov 3 12:00:13 2009 # CONFIG_ARM=y CONFIG_SYS_SUPPORTS_APM_EMULATION=y CONFIG_GENERIC_GPIO=y CONFIG_GENERIC_TIME=y CONFIG_GENERIC_CLOCKEVENTS=y -CONFIG_MMU=y -# CONFIG_NO_IOPORT is not set CONFIG_GENERIC_HARDIRQS=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y @@ -18,13 +16,13 @@ CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_HARDIRQS_SW_RESEND=y CONFIG_GENERIC_IRQ_PROBE=y CONFIG_RWSEM_GENERIC_SPINLOCK=y -# CONFIG_ARCH_HAS_ILOG2_U32 is not set -# CONFIG_ARCH_HAS_ILOG2_U64 is not set +CONFIG_ARCH_HAS_CPUFREQ=y CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y CONFIG_VECTORS_BASE=0xffff0000 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -46,11 +44,12 @@ CONFIG_BSD_PROCESS_ACCT=y # # RCU Subsystem # -CONFIG_CLASSIC_RCU=y -# CONFIG_TREE_RCU is not set -# CONFIG_PREEMPT_RCU is not set +CONFIG_TREE_RCU=y +# CONFIG_TREE_PREEMPT_RCU is not set +# CONFIG_RCU_TRACE is not set +CONFIG_RCU_FANOUT=32 +# CONFIG_RCU_FANOUT_EXACT is not set # CONFIG_TREE_RCU_TRACE is not set -# CONFIG_PREEMPT_RCU_TRACE is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=14 CONFIG_GROUP_SCHED=y @@ -77,7 +76,6 @@ CONFIG_UID16=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_ALL is not set CONFIG_KALLSYMS_EXTRA_PASS=y -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -90,18 +88,25 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y + +# +# Kernel Performance Events And Counters +# CONFIG_VM_EVENT_COUNTERS=y CONFIG_COMPAT_BRK=y CONFIG_SLAB=y # CONFIG_SLUB is not set # CONFIG_SLOB is not set # CONFIG_PROFILING is not set -# CONFIG_MARKERS is not set CONFIG_HAVE_OPROFILE=y # CONFIG_KPROBES is not set CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_CLK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set CONFIG_HAVE_GENERIC_DMA_COHERENT=y CONFIG_SLABINFO=y @@ -114,7 +119,7 @@ CONFIG_MODULE_UNLOAD=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -135,19 +140,22 @@ CONFIG_FREEZER=y # # System Type # +CONFIG_MMU=y # CONFIG_ARCH_AAEC2000 is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_REALVIEW is not set # CONFIG_ARCH_VERSATILE is not set # CONFIG_ARCH_AT91 is not set # CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_GEMINI is not set # CONFIG_ARCH_EBSA110 is not set # CONFIG_ARCH_EP93XX is not set -# CONFIG_ARCH_GEMINI is not set # CONFIG_ARCH_FOOTBRIDGE is not set +# CONFIG_ARCH_MXC is not set +# CONFIG_ARCH_STMP3XXX is not set # CONFIG_ARCH_NETX is not set # CONFIG_ARCH_H720X is not set -# CONFIG_ARCH_IMX is not set +# CONFIG_ARCH_NOMADIK is not set # CONFIG_ARCH_IOP13XX is not set # CONFIG_ARCH_IOP32X is not set # CONFIG_ARCH_IOP33X is not set @@ -156,25 +164,27 @@ CONFIG_FREEZER=y # CONFIG_ARCH_IXP4XX is not set # CONFIG_ARCH_L7200 is not set # CONFIG_ARCH_KIRKWOOD is not set -# CONFIG_ARCH_KS8695 is not set -# CONFIG_ARCH_NS9XXX is not set # CONFIG_ARCH_LOKI is not set # CONFIG_ARCH_MV78XX0 is not set -# CONFIG_ARCH_MXC is not set # CONFIG_ARCH_ORION5X is not set +# CONFIG_ARCH_MMP is not set +# CONFIG_ARCH_KS8695 is not set +# CONFIG_ARCH_NS9XXX is not set +# CONFIG_ARCH_W90X900 is not set # CONFIG_ARCH_PNX4008 is not set # CONFIG_ARCH_PXA is not set -# CONFIG_ARCH_MMP is not set +# CONFIG_ARCH_MSM is not set # CONFIG_ARCH_RPC is not set # CONFIG_ARCH_SA1100 is not set # CONFIG_ARCH_S3C2410 is not set # CONFIG_ARCH_S3C64XX is not set +# CONFIG_ARCH_S5PC1XX is not set # CONFIG_ARCH_SHARK is not set # CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_U300 is not set # CONFIG_ARCH_DAVINCI is not set CONFIG_ARCH_OMAP=y -# CONFIG_ARCH_MSM is not set -# CONFIG_ARCH_W90X900 is not set +# CONFIG_ARCH_BCMRING is not set # # TI OMAP Implementations @@ -202,21 +212,26 @@ CONFIG_OMAP_32K_TIMER_HZ=128 CONFIG_OMAP_DM_TIMER=y # CONFIG_OMAP_LL_DEBUG_UART1 is not set # CONFIG_OMAP_LL_DEBUG_UART2 is not set -CONFIG_OMAP_LL_DEBUG_UART3=y +# CONFIG_OMAP_LL_DEBUG_UART3 is not set +CONFIG_OMAP_LL_DEBUG_NONE=y +# CONFIG_OMAP_PM_NONE is not set +CONFIG_OMAP_PM_NOOP=y CONFIG_ARCH_OMAP34XX=y CONFIG_ARCH_OMAP3430=y # # OMAP Board Type # -# CONFIG_MACH_NOKIA_RX51 is not set -# CONFIG_MACH_OMAP_LDP is not set -# CONFIG_MACH_OMAP_3430SDP is not set -# CONFIG_MACH_OMAP3EVM is not set # CONFIG_MACH_OMAP3_BEAGLE is not set +# CONFIG_MACH_OMAP_LDP is not set # CONFIG_MACH_OVERO is not set +# CONFIG_MACH_OMAP3EVM is not set # CONFIG_MACH_OMAP3_PANDORA is not set +# CONFIG_MACH_OMAP_3430SDP is not set +# CONFIG_MACH_NOKIA_RX51 is not set CONFIG_MACH_OMAP_ZOOM2=y +# CONFIG_MACH_CM_T35 is not set +# CONFIG_MACH_OMAP_ZOOM3 is not set # # Processor Type @@ -226,7 +241,7 @@ CONFIG_CPU_32v6K=y CONFIG_CPU_V7=y CONFIG_CPU_32v7=y CONFIG_CPU_ABRT_EV7=y -CONFIG_CPU_PABRT_IFAR=y +CONFIG_CPU_PABRT_V7=y CONFIG_CPU_CACHE_V7=y CONFIG_CPU_CACHE_VIPT=y CONFIG_CPU_COPY_V6=y @@ -244,7 +259,7 @@ CONFIG_ARM_THUMB=y # CONFIG_CPU_DCACHE_DISABLE is not set # CONFIG_CPU_BPREDICT_DISABLE is not set CONFIG_HAS_TLS_REG=y -# CONFIG_OUTER_CACHE is not set +CONFIG_ARM_L1_CACHE_SHIFT=6 # CONFIG_ARM_ERRATA_430973 is not set # CONFIG_ARM_ERRATA_458693 is not set # CONFIG_ARM_ERRATA_460075 is not set @@ -268,11 +283,13 @@ CONFIG_VMSPLIT_3G=y # CONFIG_VMSPLIT_2G is not set # CONFIG_VMSPLIT_1G is not set CONFIG_PAGE_OFFSET=0xC0000000 +CONFIG_PREEMPT_NONE=y +# CONFIG_PREEMPT_VOLUNTARY is not set # CONFIG_PREEMPT is not set CONFIG_HZ=128 +# CONFIG_THUMB2_KERNEL is not set CONFIG_AEABI=y CONFIG_OABI_COMPAT=y -# CONFIG_ARCH_HAS_HOLES_MEMORYMODEL is not set # CONFIG_ARCH_SPARSEMEM_DEFAULT is not set # CONFIG_ARCH_SELECT_MEMORY_MODEL is not set # CONFIG_HIGHMEM is not set @@ -287,11 +304,13 @@ CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=0 CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +# CONFIG_KSM is not set +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 # CONFIG_LEDS is not set CONFIG_ALIGNMENT_TRAP=y +# CONFIG_UACCESS_WITH_MEMCPY is not set # # Boot options @@ -343,6 +362,7 @@ CONFIG_SUSPEND=y # CONFIG_PM_TEST_SUSPEND is not set CONFIG_SUSPEND_FREEZER=y # CONFIG_APM_EMULATION is not set +# CONFIG_PM_RUNTIME is not set CONFIG_ARCH_SUSPEND_POSSIBLE=y CONFIG_NET=y @@ -392,6 +412,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_NETFILTER is not set # CONFIG_IP_DCCP is not set # CONFIG_IP_SCTP is not set +# CONFIG_RDS is not set # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set @@ -406,6 +427,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -431,6 +453,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # Generic Driver Options # CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +# CONFIG_DEVTMPFS is not set CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_FW_LOADER is not set @@ -453,9 +476,9 @@ CONFIG_BLK_DEV_RAM_SIZE=16384 # CONFIG_BLK_DEV_XIP is not set # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set +# CONFIG_MG_DISK is not set CONFIG_MISC_DEVICES=y # CONFIG_ICS932S401 is not set -# CONFIG_OMAP_STI is not set # CONFIG_ENCLOSURE_SERVICES is not set # CONFIG_ISL29003 is not set # CONFIG_C2PORT is not set @@ -466,6 +489,7 @@ CONFIG_MISC_DEVICES=y # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_AT25 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -489,10 +513,6 @@ CONFIG_BLK_DEV_SD=y # CONFIG_BLK_DEV_SR is not set # CONFIG_CHR_DEV_SG is not set # CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# # CONFIG_SCSI_MULTI_LUN is not set # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set @@ -517,7 +537,6 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_ATA is not set # CONFIG_MD is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -562,12 +581,12 @@ CONFIG_SMSC911X=y # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set +# CONFIG_KS8851 is not set +# CONFIG_KS8851_MLL is not set CONFIG_NETDEV_1000=y CONFIG_NETDEV_10000=y - -# -# Wireless LAN -# +CONFIG_WLAN=y # CONFIG_WLAN_PRE80211 is not set # CONFIG_WLAN_80211 is not set @@ -590,6 +609,7 @@ CONFIG_NETDEV_10000=y # CONFIG_NETPOLL is not set # CONFIG_NET_POLL_CONTROLLER is not set # CONFIG_ISDN is not set +# CONFIG_PHONE is not set # # Input device support @@ -619,21 +639,22 @@ CONFIG_TOUCHSCREEN_ADS7846=y # CONFIG_TOUCHSCREEN_AD7879_I2C is not set # CONFIG_TOUCHSCREEN_AD7879_SPI is not set # CONFIG_TOUCHSCREEN_AD7879 is not set +# CONFIG_TOUCHSCREEN_EETI is not set # CONFIG_TOUCHSCREEN_FUJITSU is not set # CONFIG_TOUCHSCREEN_GUNZE is not set # CONFIG_TOUCHSCREEN_ELO is not set # CONFIG_TOUCHSCREEN_WACOM_W8001 is not set +# CONFIG_TOUCHSCREEN_MCS5000 is not set # CONFIG_TOUCHSCREEN_MTOUCH is not set # CONFIG_TOUCHSCREEN_INEXIO is not set # CONFIG_TOUCHSCREEN_MK712 is not set # CONFIG_TOUCHSCREEN_PENMOUNT is not set # CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set # CONFIG_TOUCHSCREEN_TOUCHWIN is not set -# CONFIG_TOUCHSCREEN_TSC2005 is not set -# CONFIG_TOUCHSCREEN_TSC210X is not set # CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set # CONFIG_TOUCHSCREEN_TOUCHIT213 is not set # CONFIG_TOUCHSCREEN_TSC2007 is not set +# CONFIG_TOUCHSCREEN_W90X900 is not set # CONFIG_INPUT_MISC is not set # @@ -683,6 +704,7 @@ CONFIG_HW_RANDOM=y # CONFIG_TCG_TPM is not set CONFIG_I2C=y CONFIG_I2C_BOARDINFO=y +CONFIG_I2C_COMPAT=y CONFIG_I2C_CHARDEV=y CONFIG_I2C_HELPER_AUTO=y @@ -693,6 +715,7 @@ CONFIG_I2C_HELPER_AUTO=y # # I2C system bus drivers (mostly embedded / system-on-chip) # +# CONFIG_I2C_DESIGNWARE is not set # CONFIG_I2C_GPIO is not set # CONFIG_I2C_OCORES is not set CONFIG_I2C_OMAP=y @@ -715,12 +738,6 @@ CONFIG_I2C_OMAP=y # Miscellaneous I2C Chip support # # CONFIG_DS1682 is not set -# CONFIG_SENSORS_PCF8574 is not set -# CONFIG_PCF8575 is not set -# CONFIG_SENSORS_PCA9539 is not set -# CONFIG_TWL4030_MADC is not set -# CONFIG_TWL4030_POWEROFF is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set @@ -742,6 +759,11 @@ CONFIG_SPI_OMAP24XX=y # # CONFIG_SPI_SPIDEV is not set # CONFIG_SPI_TLE62X0 is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_REQUIRE_GPIOLIB=y CONFIG_GPIOLIB=y # CONFIG_DEBUG_GPIO is not set @@ -768,6 +790,11 @@ CONFIG_GPIO_TWL4030=y # # CONFIG_GPIO_MAX7301 is not set # CONFIG_GPIO_MCP23S08 is not set +# CONFIG_GPIO_MC33880 is not set + +# +# AC97 GPIO expanders: +# CONFIG_W1=y CONFIG_W1_CON=y @@ -793,10 +820,11 @@ CONFIG_POWER_SUPPLY=y # CONFIG_POWER_SUPPLY_DEBUG is not set # CONFIG_PDA_POWER is not set # CONFIG_BATTERY_DS2760 is not set +# CONFIG_BATTERY_DS2782 is not set # CONFIG_BATTERY_BQ27x00 is not set +# CONFIG_BATTERY_MAX17040 is not set # CONFIG_HWMON is not set # CONFIG_THERMAL is not set -# CONFIG_THERMAL_HWMON is not set CONFIG_WATCHDOG=y CONFIG_WATCHDOG_NOWAYOUT=y @@ -805,6 +833,7 @@ CONFIG_WATCHDOG_NOWAYOUT=y # # CONFIG_SOFT_WATCHDOG is not set # CONFIG_OMAP_WATCHDOG is not set +# CONFIG_TWL4030_WATCHDOG is not set # # USB-based Watchdog Cards @@ -827,31 +856,31 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_HTC_PASIC3 is not set # CONFIG_TPS65010 is not set CONFIG_TWL4030_CORE=y +# CONFIG_TWL4030_POWER is not set # CONFIG_MFD_TMIO is not set # CONFIG_MFD_T7L66XB is not set # CONFIG_MFD_TC6387XB is not set # CONFIG_MFD_TC6393XB is not set # CONFIG_PMIC_DA903X is not set # CONFIG_MFD_WM8400 is not set +# CONFIG_MFD_WM831X is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y -# CONFIG_USB_DABUSB is not set +# CONFIG_MFD_MC13783 is not set +# CONFIG_AB3100_CORE is not set +# CONFIG_EZX_PCAP is not set +CONFIG_REGULATOR=y +# CONFIG_REGULATOR_DEBUG is not set +# CONFIG_REGULATOR_FIXED_VOLTAGE is not set +# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set +# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set +# CONFIG_REGULATOR_BQ24022 is not set +# CONFIG_REGULATOR_MAX1586 is not set +CONFIG_REGULATOR_TWL4030=y +# CONFIG_REGULATOR_LP3971 is not set +# CONFIG_REGULATOR_TPS65023 is not set +# CONFIG_REGULATOR_TPS6507X is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -883,6 +912,11 @@ CONFIG_SND_SUPPORT_OLD_API=y CONFIG_SND_VERBOSE_PROCFS=y # CONFIG_SND_VERBOSE_PRINTK is not set # CONFIG_SND_DEBUG is not set +# CONFIG_SND_RAWMIDI_SEQ is not set +# CONFIG_SND_OPL3_LIB_SEQ is not set +# CONFIG_SND_OPL4_LIB_SEQ is not set +# CONFIG_SND_SBAWE_SEQ is not set +# CONFIG_SND_EMU10K1_SEQ is not set CONFIG_SND_DRIVERS=y # CONFIG_SND_DUMMY is not set # CONFIG_SND_MTPAV is not set @@ -897,7 +931,6 @@ CONFIG_SND_USB=y # CONFIG_SOUND_PRIME is not set CONFIG_HID_SUPPORT=y CONFIG_HID=y -# CONFIG_HID_DEBUG is not set # CONFIG_HIDRAW is not set # @@ -916,10 +949,11 @@ CONFIG_USB_HID=y # CONFIG_HID_CHERRY is not set # CONFIG_HID_CHICONY is not set # CONFIG_HID_CYPRESS is not set -# CONFIG_DRAGONRISE_FF is not set +# CONFIG_HID_DRAGONRISE is not set # CONFIG_HID_EZKEY is not set # CONFIG_HID_KYE is not set # CONFIG_HID_GYRATION is not set +# CONFIG_HID_TWINHAN is not set # CONFIG_HID_KENSINGTON is not set # CONFIG_HID_LOGITECH is not set # CONFIG_HID_MICROSOFT is not set @@ -930,10 +964,11 @@ CONFIG_USB_HID=y # CONFIG_HID_SAMSUNG is not set # CONFIG_HID_SONY is not set # CONFIG_HID_SUNPLUS is not set -# CONFIG_GREENASIA_FF is not set +# CONFIG_HID_GREENASIA is not set +# CONFIG_HID_SMARTJOYPLUS is not set # CONFIG_HID_TOPSEED is not set -# CONFIG_THRUSTMASTER_FF is not set -# CONFIG_ZEROPLUS_FF is not set +# CONFIG_HID_THRUSTMASTER is not set +# CONFIG_HID_ZEROPLUS is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y @@ -964,6 +999,7 @@ CONFIG_USB_MON=y # CONFIG_USB_OXU210HP_HCD is not set # CONFIG_USB_ISP116X_HCD is not set # CONFIG_USB_ISP1760_HCD is not set +# CONFIG_USB_ISP1362_HCD is not set # CONFIG_USB_OHCI_HCD is not set # CONFIG_USB_SL811_HCD is not set # CONFIG_USB_R8A66597_HCD is not set @@ -1030,9 +1066,11 @@ CONFIG_USB_MUSB_DEBUG=y # CONFIG_USB_IDMOUSE is not set # CONFIG_USB_FTDI_ELAN is not set # CONFIG_USB_APPLEDISPLAY is not set +# CONFIG_USB_SISUSBVGA is not set # CONFIG_USB_LD is not set # CONFIG_USB_TRANCEVIBRATOR is not set # CONFIG_USB_IOWARRIOR is not set +# CONFIG_USB_TEST is not set # CONFIG_USB_ISIGHTFW is not set # CONFIG_USB_VST is not set CONFIG_USB_GADGET=y @@ -1046,19 +1084,23 @@ CONFIG_USB_GADGET_SELECTED=y # CONFIG_USB_GADGET_LH7A40X is not set # CONFIG_USB_GADGET_OMAP is not set # CONFIG_USB_GADGET_PXA25X is not set +# CONFIG_USB_GADGET_R8A66597 is not set # CONFIG_USB_GADGET_PXA27X is not set -# CONFIG_USB_GADGET_S3C2410 is not set +# CONFIG_USB_GADGET_S3C_HSOTG is not set # CONFIG_USB_GADGET_IMX is not set +# CONFIG_USB_GADGET_S3C2410 is not set # CONFIG_USB_GADGET_M66592 is not set # CONFIG_USB_GADGET_AMD5536UDC is not set # CONFIG_USB_GADGET_FSL_QE is not set # CONFIG_USB_GADGET_CI13XXX is not set # CONFIG_USB_GADGET_NET2280 is not set # CONFIG_USB_GADGET_GOKU is not set +# CONFIG_USB_GADGET_LANGWELL is not set # CONFIG_USB_GADGET_DUMMY_HCD is not set CONFIG_USB_GADGET_DUALSPEED=y -CONFIG_USB_ZERO=y +CONFIG_USB_ZERO=m # CONFIG_USB_ZERO_HNPTEST is not set +# CONFIG_USB_AUDIO is not set # CONFIG_USB_ETH is not set # CONFIG_USB_GADGETFS is not set # CONFIG_USB_FILE_STORAGE is not set @@ -1091,11 +1133,14 @@ CONFIG_MMC_BLOCK_BOUNCE=y # MMC/SD/SDIO Host Controller Drivers # # CONFIG_MMC_SDHCI is not set +# CONFIG_MMC_OMAP is not set CONFIG_MMC_OMAP_HS=y +# CONFIG_MMC_AT91 is not set +# CONFIG_MMC_ATMELMCI is not set # CONFIG_MMC_SPI is not set # CONFIG_MEMSTICK is not set -# CONFIG_ACCESSIBILITY is not set # CONFIG_NEW_LEDS is not set +# CONFIG_ACCESSIBILITY is not set CONFIG_RTC_LIB=y CONFIG_RTC_CLASS=y CONFIG_RTC_HCTOSYS=y @@ -1128,6 +1173,7 @@ CONFIG_RTC_INTF_DEV=y # CONFIG_RTC_DRV_S35390A is not set # CONFIG_RTC_DRV_FM3130 is not set # CONFIG_RTC_DRV_RX8581 is not set +# CONFIG_RTC_DRV_RX8025 is not set # # SPI RTC drivers @@ -1139,6 +1185,7 @@ CONFIG_RTC_INTF_DEV=y # CONFIG_RTC_DRV_R9701 is not set # CONFIG_RTC_DRV_RS5C348 is not set # CONFIG_RTC_DRV_DS3234 is not set +# CONFIG_RTC_DRV_PCF2123 is not set # # Platform RTC drivers @@ -1160,13 +1207,11 @@ CONFIG_RTC_INTF_DEV=y # # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set -CONFIG_REGULATOR=y -# CONFIG_REGULATOR_DEBUG is not set -# CONFIG_REGULATOR_FIXED_VOLTAGE is not set -# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set -# CONFIG_REGULATOR_BQ24022 is not set -CONFIG_REGULATOR_TWL4030=y # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1188,10 +1233,13 @@ CONFIG_JBD=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set CONFIG_FS_POSIX_ACL=y -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +# CONFIG_NILFS2_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1256,12 +1304,12 @@ CONFIG_MISC_FILESYSTEMS=y # CONFIG_ROMFS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set -# CONFIG_NILFS2_FS is not set CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y CONFIG_NFS_V3_ACL=y CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set CONFIG_ROOT_NFS=y # CONFIG_NFSD is not set CONFIG_LOCKD=y @@ -1349,6 +1397,7 @@ CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y CONFIG_FRAME_WARN=1024 CONFIG_MAGIC_SYSRQ=y +# CONFIG_STRIP_ASM_SYMS is not set # CONFIG_UNUSED_SYMBOLS is not set # CONFIG_DEBUG_FS is not set # CONFIG_HEADERS_CHECK is not set @@ -1365,6 +1414,7 @@ CONFIG_SCHED_DEBUG=y # CONFIG_TIMER_STATS is not set # CONFIG_DEBUG_OBJECTS is not set # CONFIG_DEBUG_SLAB is not set +# CONFIG_DEBUG_KMEMLEAK is not set # CONFIG_DEBUG_RT_MUTEXES is not set # CONFIG_RT_MUTEX_TESTER is not set # CONFIG_DEBUG_SPINLOCK is not set @@ -1383,27 +1433,27 @@ CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set +# CONFIG_DEBUG_CREDENTIALS is not set # CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set # CONFIG_DEBUG_BLOCK_EXT_DEVT is not set +# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set # CONFIG_FAULT_INJECTION is not set # CONFIG_LATENCYTOP is not set # CONFIG_PAGE_POISONING is not set CONFIG_HAVE_FUNCTION_TRACER=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# +CONFIG_FTRACE=y # CONFIG_FUNCTION_TRACER is not set # CONFIG_IRQSOFF_TRACER is not set # CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set # CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set # CONFIG_STACK_TRACER is not set # CONFIG_KMEMTRACE is not set # CONFIG_WORKQUEUE_TRACER is not set @@ -1430,7 +1480,6 @@ CONFIG_CRYPTO=y # # Crypto core or helper # -# CONFIG_CRYPTO_FIPS is not set CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_ALGAPI2=y CONFIG_CRYPTO_AEAD2=y @@ -1472,11 +1521,13 @@ CONFIG_CRYPTO_PCBC=m # # CONFIG_CRYPTO_HMAC is not set # CONFIG_CRYPTO_XCBC is not set +# CONFIG_CRYPTO_VMAC is not set # # Digest # CONFIG_CRYPTO_CRC32C=y +# CONFIG_CRYPTO_GHASH is not set # CONFIG_CRYPTO_MD4 is not set CONFIG_CRYPTO_MD5=y # CONFIG_CRYPTO_MICHAEL_MIC is not set -- 1.6.5.1.69.g36942 ^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH 5/8] omap: zoom3: introduce zoom3 board support 2009-11-03 21:20 ` [PATCH 4/8] omap: zoom2: update defconfig Vikram Pandita @ 2009-11-03 21:20 ` Vikram Pandita 2009-11-03 21:20 ` [PATCH 6/8] omap: zoom3: defconfig creation Vikram Pandita 2009-11-03 22:28 ` [PATCH 5/8] omap: zoom3: introduce zoom3 " Nishanth Menon 2009-11-04 7:09 ` [PATCH 4/8] omap: zoom2: update defconfig G, Manjunath Kondaiah 1 sibling, 2 replies; 16+ messages in thread From: Vikram Pandita @ 2009-11-03 21:20 UTC (permalink / raw) To: linux-omap; +Cc: Vikram Pandita, Vikram Pandita Zoom3 is the next versoin of Zoom2 board. There has been a silicon update from zoom2 to zoom3. Zoom2 has OMAP34xx Zoom3 has OMAP3630 Zoom3 = OMAP3630 SOM board + same zoom2 main board + same debugboard Zoom3 has a different SDRAM part from Hynix Zoom2 had SDRAM part from micron Reuse the zoom2 files as much for zoom3, as at board level, there is no change at all. Signed-off-by: Vikram Pandita <vikram.pandtia@ti.com> --- arch/arm/mach-omap2/Kconfig | 4 + arch/arm/mach-omap2/Makefile | 4 + arch/arm/mach-omap2/board-zoom3.c | 59 ++++++++++++++++++++ arch/arm/mach-omap2/sdram-hynix-h8mbx00u0mer-0em.h | 54 ++++++++++++++++++ 4 files changed, 121 insertions(+), 0 deletions(-) create mode 100755 arch/arm/mach-omap2/board-zoom3.c create mode 100644 arch/arm/mach-omap2/sdram-hynix-h8mbx00u0mer-0em.h diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig index 8685df5..9824775 100644 --- a/arch/arm/mach-omap2/Kconfig +++ b/arch/arm/mach-omap2/Kconfig @@ -101,6 +101,10 @@ config MACH_CM_T35 bool "CompuLab CM-T35 module" depends on ARCH_OMAP3 && ARCH_OMAP34XX +config MACH_OMAP_ZOOM3 + bool "OMAP3630 Zoom3 board" + depends on ARCH_OMAP3 && ARCH_OMAP34XX + config MACH_OMAP_4430SDP bool "OMAP 4430 SDP board" depends on ARCH_OMAP4 diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index 4d66b42..712e7fc 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -75,6 +75,10 @@ obj-$(CONFIG_MACH_OMAP_ZOOM2) += board-zoom2.o \ board-zoom-peripherals.o \ mmc-twl4030.o \ board-zoom-debugboard.o +obj-$(CONFIG_MACH_OMAP_ZOOM3) += board-zoom3.o \ + board-zoom-peripherals.o \ + mmc-twl4030.o \ + board-zoom-debugboard.o obj-$(CONFIG_MACH_CM_T35) += board-cm-t35.o \ mmc-twl4030.o diff --git a/arch/arm/mach-omap2/board-zoom3.c b/arch/arm/mach-omap2/board-zoom3.c new file mode 100755 index 0000000..aebe7b8 --- /dev/null +++ b/arch/arm/mach-omap2/board-zoom3.c @@ -0,0 +1,59 @@ +/* + * Copyright (C) 2009 Texas Instruments Inc. + * + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/input.h> +#include <linux/gpio.h> + +#include <asm/mach-types.h> +#include <asm/mach/arch.h> + +#include <plat/common.h> +#include <plat/board.h> + +#include "sdram-hynix-h8mbx00u0mer-0em.h" + +static void __init omap_zoom_map_io(void) +{ + omap2_set_globals_343x(); + omap2_map_common_io(); +} + +static struct omap_board_config_kernel zoom_config[] __initdata = { +}; +static void __init omap_zoom_init_irq(void) +{ + omap_board_config = zoom_config; + omap_board_config_size = ARRAY_SIZE(zoom_config); + omap2_init_common_hw(h8mbx00u0mer0em_sdrc_params, + h8mbx00u0mer0em_sdrc_params); + omap_init_irq(); + omap_gpio_init(); +} + +extern int __init omap_zoom2_debugboard_init(void); +extern void __init zoom_peripherals_init(void); + +static void __init omap_zoom_init(void) +{ + zoom_peripherals_init(); + omap_zoom2_debugboard_init(); +} + +MACHINE_START(OMAP_ZOOM3, "OMAP Zoom3 board") + .phys_io = 0x48000000, + .io_pg_offst = ((0xfa000000) >> 18) & 0xfffc, + .boot_params = 0x80000100, + .map_io = omap_zoom_map_io, + .init_irq = omap_zoom_init_irq, + .init_machine = omap_zoom_init, + .timer = &omap_timer, +MACHINE_END diff --git a/arch/arm/mach-omap2/sdram-hynix-h8mbx00u0mer-0em.h b/arch/arm/mach-omap2/sdram-hynix-h8mbx00u0mer-0em.h new file mode 100644 index 0000000..c469c48 --- /dev/null +++ b/arch/arm/mach-omap2/sdram-hynix-h8mbx00u0mer-0em.h @@ -0,0 +1,54 @@ +/* + * SDRC register values for the Hynix H8MBX00U0MER-0EM + * + * Copyright (C) 2008-2009 Texas Instruments, Inc. + * Copyright (C) 2008-2009 Nokia Corporation + * + * Nicole Chalhoub / Vincent Bour + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef ARCH_ARM_MACH_OMAP2_SDRAM_HYNIX_H8MBX00U0MER0EM +#define ARCH_ARM_MACH_OMAP2_SDRAM_HYNIX_H8MBX00U0MER0EM + +#include <plat/sdrc.h> + +/* Hynix H8MBX00U0MER-0EM */ +static struct omap_sdrc_params h8mbx00u0mer0em_sdrc_params[] = { + [0] = { + .rate = 200000000, + .actim_ctrla = 0xa2e1b4c6, + .actim_ctrlb = 0x0002131c, + .rfr_ctrl = 0x0005e601, + .mr = 0x00000032, + }, + [1] = { + .rate = 166000000, + .actim_ctrla = 0x629db4c6, + .actim_ctrlb = 0x00012214, + .rfr_ctrl = 0x0004dc01, + .mr = 0x00000032, + }, + [2] = { + .rate = 100000000, + .actim_ctrla = 0x51912284, + .actim_ctrlb = 0x0002120e, + .rfr_ctrl = 0x0002d101, + .mr = 0x00000022, + }, + [3] = { + .rate = 83000000, + .actim_ctrla = 0x31512283, + .actim_ctrlb = 0x0001220a, + .rfr_ctrl = 0x00025501, + .mr = 0x00000022, + }, + [4] = { + .rate = 0 + }, +}; + +#endif -- 1.6.5.1.69.g36942 ^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH 6/8] omap: zoom3: defconfig creation 2009-11-03 21:20 ` [PATCH 5/8] omap: zoom3: introduce zoom3 board support Vikram Pandita @ 2009-11-03 21:20 ` Vikram Pandita 2009-11-03 21:20 ` [PATCH 7/8] omap: 3630sdp: introduce 3630 sdp board support Vikram Pandita 2009-11-03 22:28 ` [PATCH 5/8] omap: zoom3: introduce zoom3 " Nishanth Menon 1 sibling, 1 reply; 16+ messages in thread From: Vikram Pandita @ 2009-11-03 21:20 UTC (permalink / raw) To: linux-omap; +Cc: Vikram Pandita Create zoom3 defconfig file Signed-off-by: Vikram Pandita <vikram.pandita@ti.com> --- arch/arm/configs/omap_zoom3_defconfig | 1605 +++++++++++++++++++++++++++++++++ 1 files changed, 1605 insertions(+), 0 deletions(-) create mode 100644 arch/arm/configs/omap_zoom3_defconfig diff --git a/arch/arm/configs/omap_zoom3_defconfig b/arch/arm/configs/omap_zoom3_defconfig new file mode 100644 index 0000000..989cedd --- /dev/null +++ b/arch/arm/configs/omap_zoom3_defconfig @@ -0,0 +1,1605 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.32-rc5 +# Tue Nov 3 09:50:40 2009 +# +CONFIG_ARM=y +CONFIG_SYS_SUPPORTS_APM_EMULATION=y +CONFIG_GENERIC_GPIO=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_HARDIRQS=y +CONFIG_STACKTRACE_SUPPORT=y +CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_LOCKDEP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_ARCH_HAS_CPUFREQ=y +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y +CONFIG_VECTORS_BASE=0xffff0000 +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y + +# +# General setup +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +CONFIG_SWAP=y +CONFIG_SYSVIPC=y +CONFIG_SYSVIPC_SYSCTL=y +# CONFIG_POSIX_MQUEUE is not set +CONFIG_BSD_PROCESS_ACCT=y +# CONFIG_BSD_PROCESS_ACCT_V3 is not set +# CONFIG_TASKSTATS is not set +# CONFIG_AUDIT is not set + +# +# RCU Subsystem +# +CONFIG_TREE_RCU=y +# CONFIG_TREE_PREEMPT_RCU is not set +# CONFIG_RCU_TRACE is not set +CONFIG_RCU_FANOUT=32 +# CONFIG_RCU_FANOUT_EXACT is not set +# CONFIG_TREE_RCU_TRACE is not set +# CONFIG_IKCONFIG is not set +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_GROUP_SCHED=y +CONFIG_FAIR_GROUP_SCHED=y +# CONFIG_RT_GROUP_SCHED is not set +CONFIG_USER_SCHED=y +# CONFIG_CGROUP_SCHED is not set +# CONFIG_CGROUPS is not set +CONFIG_SYSFS_DEPRECATED=y +CONFIG_SYSFS_DEPRECATED_V2=y +# CONFIG_RELAY is not set +# CONFIG_NAMESPACES is not set +CONFIG_BLK_DEV_INITRD=y +CONFIG_INITRAMFS_SOURCE="" +CONFIG_RD_GZIP=y +# CONFIG_RD_BZIP2 is not set +# CONFIG_RD_LZMA is not set +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +CONFIG_SYSCTL=y +CONFIG_ANON_INODES=y +CONFIG_EMBEDDED=y +CONFIG_UID16=y +# CONFIG_SYSCTL_SYSCALL is not set +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +CONFIG_KALLSYMS_EXTRA_PASS=y +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_TIMERFD=y +CONFIG_EVENTFD=y +CONFIG_SHMEM=y +CONFIG_AIO=y + +# +# Kernel Performance Events And Counters +# +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_COMPAT_BRK=y +CONFIG_SLAB=y +# CONFIG_SLUB is not set +# CONFIG_SLOB is not set +# CONFIG_PROFILING is not set +CONFIG_HAVE_OPROFILE=y +# CONFIG_KPROBES is not set +CONFIG_HAVE_KPROBES=y +CONFIG_HAVE_KRETPROBES=y +CONFIG_HAVE_CLK=y + +# +# GCOV-based kernel profiling +# +# CONFIG_SLOW_WORK is not set +CONFIG_HAVE_GENERIC_DMA_COHERENT=y +CONFIG_SLABINFO=y +CONFIG_RT_MUTEXES=y +CONFIG_BASE_SMALL=0 +CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +CONFIG_MODVERSIONS=y +CONFIG_MODULE_SRCVERSION_ALL=y +CONFIG_BLOCK=y +CONFIG_LBDAF=y +# CONFIG_BLK_DEV_BSG is not set +# CONFIG_BLK_DEV_INTEGRITY is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" +CONFIG_FREEZER=y + +# +# System Type +# +CONFIG_MMU=y +# CONFIG_ARCH_AAEC2000 is not set +# CONFIG_ARCH_INTEGRATOR is not set +# CONFIG_ARCH_REALVIEW is not set +# CONFIG_ARCH_VERSATILE is not set +# CONFIG_ARCH_AT91 is not set +# CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_GEMINI is not set +# CONFIG_ARCH_EBSA110 is not set +# CONFIG_ARCH_EP93XX is not set +# CONFIG_ARCH_FOOTBRIDGE is not set +# CONFIG_ARCH_MXC is not set +# CONFIG_ARCH_STMP3XXX is not set +# CONFIG_ARCH_NETX is not set +# CONFIG_ARCH_H720X is not set +# CONFIG_ARCH_NOMADIK is not set +# CONFIG_ARCH_IOP13XX is not set +# CONFIG_ARCH_IOP32X is not set +# CONFIG_ARCH_IOP33X is not set +# CONFIG_ARCH_IXP23XX is not set +# CONFIG_ARCH_IXP2000 is not set +# CONFIG_ARCH_IXP4XX is not set +# CONFIG_ARCH_L7200 is not set +# CONFIG_ARCH_KIRKWOOD is not set +# CONFIG_ARCH_LOKI is not set +# CONFIG_ARCH_MV78XX0 is not set +# CONFIG_ARCH_ORION5X is not set +# CONFIG_ARCH_MMP is not set +# CONFIG_ARCH_KS8695 is not set +# CONFIG_ARCH_NS9XXX is not set +# CONFIG_ARCH_W90X900 is not set +# CONFIG_ARCH_PNX4008 is not set +# CONFIG_ARCH_PXA is not set +# CONFIG_ARCH_MSM is not set +# CONFIG_ARCH_RPC is not set +# CONFIG_ARCH_SA1100 is not set +# CONFIG_ARCH_S3C2410 is not set +# CONFIG_ARCH_S3C64XX is not set +# CONFIG_ARCH_S5PC1XX is not set +# CONFIG_ARCH_SHARK is not set +# CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_U300 is not set +# CONFIG_ARCH_DAVINCI is not set +CONFIG_ARCH_OMAP=y +# CONFIG_ARCH_BCMRING is not set + +# +# TI OMAP Implementations +# +CONFIG_ARCH_OMAP_OTG=y +# CONFIG_ARCH_OMAP1 is not set +# CONFIG_ARCH_OMAP2 is not set +CONFIG_ARCH_OMAP3=y +# CONFIG_ARCH_OMAP4 is not set + +# +# OMAP Feature Selections +# +# CONFIG_OMAP_DEBUG_POWERDOMAIN is not set +# CONFIG_OMAP_DEBUG_CLOCKDOMAIN is not set +# CONFIG_OMAP_RESET_CLOCKS is not set +CONFIG_OMAP_MUX=y +CONFIG_OMAP_MUX_DEBUG=y +CONFIG_OMAP_MUX_WARNINGS=y +CONFIG_OMAP_MCBSP=y +# CONFIG_OMAP_MBOX_FWK is not set +# CONFIG_OMAP_MPU_TIMER is not set +CONFIG_OMAP_32K_TIMER=y +CONFIG_OMAP_32K_TIMER_HZ=128 +CONFIG_OMAP_DM_TIMER=y +# CONFIG_OMAP_LL_DEBUG_UART1 is not set +# CONFIG_OMAP_LL_DEBUG_UART2 is not set +# CONFIG_OMAP_LL_DEBUG_UART3 is not set +CONFIG_OMAP_LL_DEBUG_NONE=y +# CONFIG_OMAP_PM_NONE is not set +CONFIG_OMAP_PM_NOOP=y +CONFIG_ARCH_OMAP34XX=y +CONFIG_ARCH_OMAP3430=y + +# +# OMAP Board Type +# +# CONFIG_MACH_OMAP3_BEAGLE is not set +# CONFIG_MACH_OMAP_LDP is not set +# CONFIG_MACH_OVERO is not set +# CONFIG_MACH_OMAP3EVM is not set +# CONFIG_MACH_OMAP3_PANDORA is not set +# CONFIG_MACH_OMAP_3430SDP is not set +# CONFIG_MACH_NOKIA_RX51 is not set +# CONFIG_MACH_OMAP_ZOOM2 is not set +# CONFIG_MACH_CM_T35 is not set +CONFIG_MACH_OMAP_ZOOM3=y + +# +# Processor Type +# +CONFIG_CPU_32=y +CONFIG_CPU_32v6K=y +CONFIG_CPU_V7=y +CONFIG_CPU_32v7=y +CONFIG_CPU_ABRT_EV7=y +CONFIG_CPU_PABRT_V7=y +CONFIG_CPU_CACHE_V7=y +CONFIG_CPU_CACHE_VIPT=y +CONFIG_CPU_COPY_V6=y +CONFIG_CPU_TLB_V7=y +CONFIG_CPU_HAS_ASID=y +CONFIG_CPU_CP15=y +CONFIG_CPU_CP15_MMU=y + +# +# Processor Features +# +CONFIG_ARM_THUMB=y +# CONFIG_ARM_THUMBEE is not set +# CONFIG_CPU_ICACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_DISABLE is not set +# CONFIG_CPU_BPREDICT_DISABLE is not set +CONFIG_HAS_TLS_REG=y +CONFIG_ARM_L1_CACHE_SHIFT=6 +# CONFIG_ARM_ERRATA_430973 is not set +# CONFIG_ARM_ERRATA_458693 is not set +# CONFIG_ARM_ERRATA_460075 is not set +CONFIG_COMMON_CLKDEV=y + +# +# Bus support +# +# CONFIG_PCI_SYSCALL is not set +# CONFIG_ARCH_SUPPORTS_MSI is not set +# CONFIG_PCCARD is not set + +# +# Kernel Features +# +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +CONFIG_VMSPLIT_3G=y +# CONFIG_VMSPLIT_2G is not set +# CONFIG_VMSPLIT_1G is not set +CONFIG_PAGE_OFFSET=0xC0000000 +CONFIG_PREEMPT_NONE=y +# CONFIG_PREEMPT_VOLUNTARY is not set +# CONFIG_PREEMPT is not set +CONFIG_HZ=128 +# CONFIG_THUMB2_KERNEL is not set +CONFIG_AEABI=y +CONFIG_OABI_COMPAT=y +# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set +# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set +# CONFIG_HIGHMEM is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +CONFIG_PAGEFLAGS_EXTENDED=y +CONFIG_SPLIT_PTLOCK_CPUS=4 +# CONFIG_PHYS_ADDR_T_64BIT is not set +CONFIG_ZONE_DMA_FLAG=0 +CONFIG_VIRT_TO_BUS=y +CONFIG_HAVE_MLOCK=y +CONFIG_HAVE_MLOCKED_PAGE_BIT=y +# CONFIG_KSM is not set +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 +# CONFIG_LEDS is not set +CONFIG_ALIGNMENT_TRAP=y +# CONFIG_UACCESS_WITH_MEMCPY is not set + +# +# Boot options +# +CONFIG_ZBOOT_ROM_TEXT=0x0 +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_CMDLINE="root=/dev/nfs nfsroot=192.168.0.1:/home/user/buildroot ip=192.168.0.2:192.168.0.1:192.168.0.1:255.255.255.0:tgt:eth0:off rw console=ttyS2,115200n8" +# CONFIG_XIP_KERNEL is not set +# CONFIG_KEXEC is not set + +# +# CPU Power Management +# +# CONFIG_CPU_FREQ is not set +# CONFIG_CPU_IDLE is not set + +# +# Floating point emulation +# + +# +# At least one emulation must be selected +# +CONFIG_FPE_NWFPE=y +# CONFIG_FPE_NWFPE_XP is not set +# CONFIG_FPE_FASTFPE is not set +CONFIG_VFP=y +CONFIG_VFPv3=y +# CONFIG_NEON is not set + +# +# Userspace binary formats +# +CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +CONFIG_HAVE_AOUT=y +# CONFIG_BINFMT_AOUT is not set +CONFIG_BINFMT_MISC=y + +# +# Power management options +# +CONFIG_PM=y +CONFIG_PM_DEBUG=y +CONFIG_PM_VERBOSE=y +CONFIG_CAN_PM_TRACE=y +CONFIG_PM_SLEEP=y +CONFIG_SUSPEND=y +# CONFIG_PM_TEST_SUSPEND is not set +CONFIG_SUSPEND_FREEZER=y +# CONFIG_APM_EMULATION is not set +# CONFIG_PM_RUNTIME is not set +CONFIG_ARCH_SUSPEND_POSSIBLE=y +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +CONFIG_XFRM=y +CONFIG_XFRM_USER=y +# CONFIG_XFRM_SUB_POLICY is not set +CONFIG_XFRM_MIGRATE=y +# CONFIG_XFRM_STATISTICS is not set +CONFIG_NET_KEY=y +CONFIG_NET_KEY_MIGRATE=y +CONFIG_INET=y +CONFIG_IP_MULTICAST=y +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +CONFIG_IP_PNP_RARP=y +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_IP_MROUTE is not set +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set +CONFIG_INET_XFRM_MODE_TRANSPORT=y +CONFIG_INET_XFRM_MODE_TUNNEL=y +CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +# CONFIG_IPV6 is not set +# CONFIG_NETWORK_SECMARK is not set +# CONFIG_NETFILTER is not set +# CONFIG_IP_DCCP is not set +# CONFIG_IP_SCTP is not set +# CONFIG_RDS is not set +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set +# CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set +# CONFIG_NET_SCHED is not set +# CONFIG_DCB is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_CAN is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_AF_RXRPC is not set +# CONFIG_WIRELESS is not set +# CONFIG_WIMAX is not set +# CONFIG_RFKILL is not set +# CONFIG_NET_9P is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +# CONFIG_DEVTMPFS is not set +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_FW_LOADER is not set +# CONFIG_DEBUG_DRIVER is not set +# CONFIG_DEBUG_DEVRES is not set +# CONFIG_SYS_HYPERVISOR is not set +CONFIG_CONNECTOR=y +CONFIG_PROC_EVENTS=y +# CONFIG_MTD is not set +# CONFIG_PARPORT is not set +CONFIG_BLK_DEV=y +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=y +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +# CONFIG_BLK_DEV_NBD is not set +# CONFIG_BLK_DEV_UB is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=16384 +# CONFIG_BLK_DEV_XIP is not set +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set +# CONFIG_MG_DISK is not set +CONFIG_MISC_DEVICES=y +# CONFIG_ICS932S401 is not set +# CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_ISL29003 is not set +# CONFIG_C2PORT is not set + +# +# EEPROM support +# +# CONFIG_EEPROM_AT24 is not set +# CONFIG_EEPROM_AT25 is not set +# CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set +# CONFIG_EEPROM_93CX6 is not set +CONFIG_HAVE_IDE=y +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +CONFIG_SCSI=y +CONFIG_SCSI_DMA=y +# CONFIG_SCSI_TGT is not set +# CONFIG_SCSI_NETLINK is not set +CONFIG_SCSI_PROC_FS=y + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=y +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set +# CONFIG_BLK_DEV_SR is not set +# CONFIG_CHR_DEV_SG is not set +# CONFIG_CHR_DEV_SCH is not set +# CONFIG_SCSI_MULTI_LUN is not set +# CONFIG_SCSI_CONSTANTS is not set +# CONFIG_SCSI_LOGGING is not set +# CONFIG_SCSI_SCAN_ASYNC is not set +CONFIG_SCSI_WAIT_SCAN=m + +# +# SCSI Transports +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set +CONFIG_SCSI_LOWLEVEL=y +# CONFIG_ISCSI_TCP is not set +# CONFIG_LIBFC is not set +# CONFIG_LIBFCOE is not set +# CONFIG_SCSI_DEBUG is not set +# CONFIG_SCSI_DH is not set +# CONFIG_SCSI_OSD_INITIATOR is not set +# CONFIG_ATA is not set +# CONFIG_MD is not set +CONFIG_NETDEVICES=y +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_MACVLAN is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set +# CONFIG_VETH is not set +CONFIG_PHYLIB=y + +# +# MII PHY device drivers +# +# CONFIG_MARVELL_PHY is not set +# CONFIG_DAVICOM_PHY is not set +# CONFIG_QSEMI_PHY is not set +# CONFIG_LXT_PHY is not set +# CONFIG_CICADA_PHY is not set +# CONFIG_VITESSE_PHY is not set +CONFIG_SMSC_PHY=y +# CONFIG_BROADCOM_PHY is not set +# CONFIG_ICPLUS_PHY is not set +# CONFIG_REALTEK_PHY is not set +# CONFIG_NATIONAL_PHY is not set +# CONFIG_STE10XP is not set +# CONFIG_LSI_ET1011C_PHY is not set +# CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +# CONFIG_AX88796 is not set +# CONFIG_SMC91X is not set +# CONFIG_DM9000 is not set +# CONFIG_ENC28J60 is not set +# CONFIG_ETHOC is not set +# CONFIG_SMC911X is not set +CONFIG_SMSC911X=y +# CONFIG_DNET is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set +# CONFIG_B44 is not set +# CONFIG_KS8842 is not set +# CONFIG_KS8851 is not set +# CONFIG_KS8851_MLL is not set +CONFIG_NETDEV_1000=y +CONFIG_NETDEV_10000=y +CONFIG_WLAN=y +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set + +# +# Enable WiMAX (Networking options) to see the WiMAX drivers +# + +# +# USB Network Adapters +# +# CONFIG_USB_CATC is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_RTL8150 is not set +# CONFIG_USB_USBNET is not set +# CONFIG_WAN is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set +# CONFIG_ISDN is not set +# CONFIG_PHONE is not set + +# +# Input device support +# +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set +# CONFIG_INPUT_POLLDEV is not set + +# +# Userland interfaces +# +# CONFIG_INPUT_MOUSEDEV is not set +# CONFIG_INPUT_JOYDEV is not set +CONFIG_INPUT_EVDEV=y +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TABLET is not set +CONFIG_INPUT_TOUCHSCREEN=y +CONFIG_TOUCHSCREEN_ADS7846=y +# CONFIG_TOUCHSCREEN_AD7877 is not set +# CONFIG_TOUCHSCREEN_AD7879_I2C is not set +# CONFIG_TOUCHSCREEN_AD7879_SPI is not set +# CONFIG_TOUCHSCREEN_AD7879 is not set +# CONFIG_TOUCHSCREEN_EETI is not set +# CONFIG_TOUCHSCREEN_FUJITSU is not set +# CONFIG_TOUCHSCREEN_GUNZE is not set +# CONFIG_TOUCHSCREEN_ELO is not set +# CONFIG_TOUCHSCREEN_WACOM_W8001 is not set +# CONFIG_TOUCHSCREEN_MCS5000 is not set +# CONFIG_TOUCHSCREEN_MTOUCH is not set +# CONFIG_TOUCHSCREEN_INEXIO is not set +# CONFIG_TOUCHSCREEN_MK712 is not set +# CONFIG_TOUCHSCREEN_PENMOUNT is not set +# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set +# CONFIG_TOUCHSCREEN_TOUCHWIN is not set +# CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set +# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set +# CONFIG_TOUCHSCREEN_TSC2007 is not set +# CONFIG_TOUCHSCREEN_W90X900 is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_CONSOLE_TRANSLATIONS=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_VT_HW_CONSOLE_BINDING is not set +CONFIG_DEVKMEM=y +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_NR_UARTS=32 +CONFIG_SERIAL_8250_RUNTIME_UARTS=4 +CONFIG_SERIAL_8250_EXTENDED=y +CONFIG_SERIAL_8250_MANY_PORTS=y +CONFIG_SERIAL_8250_SHARE_IRQ=y +CONFIG_SERIAL_8250_DETECT_IRQ=y +CONFIG_SERIAL_8250_RSA=y + +# +# Non-8250 serial port support +# +# CONFIG_SERIAL_MAX3100 is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_UNIX98_PTYS=y +# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set +# CONFIG_LEGACY_PTYS is not set +# CONFIG_IPMI_HANDLER is not set +CONFIG_HW_RANDOM=y +# CONFIG_HW_RANDOM_TIMERIOMEM is not set +# CONFIG_R3964 is not set +# CONFIG_RAW_DRIVER is not set +# CONFIG_TCG_TPM is not set +CONFIG_I2C=y +CONFIG_I2C_BOARDINFO=y +CONFIG_I2C_COMPAT=y +CONFIG_I2C_CHARDEV=y +CONFIG_I2C_HELPER_AUTO=y + +# +# I2C Hardware Bus support +# + +# +# I2C system bus drivers (mostly embedded / system-on-chip) +# +# CONFIG_I2C_DESIGNWARE is not set +# CONFIG_I2C_GPIO is not set +# CONFIG_I2C_OCORES is not set +CONFIG_I2C_OMAP=y +# CONFIG_I2C_SIMTEC is not set + +# +# External I2C/SMBus adapter drivers +# +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_TAOS_EVM is not set +# CONFIG_I2C_TINY_USB is not set + +# +# Other I2C/SMBus bus drivers +# +# CONFIG_I2C_PCA_PLATFORM is not set +# CONFIG_I2C_STUB is not set + +# +# Miscellaneous I2C Chip support +# +# CONFIG_DS1682 is not set +# CONFIG_SENSORS_TSL2550 is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set +CONFIG_SPI=y +# CONFIG_SPI_DEBUG is not set +CONFIG_SPI_MASTER=y + +# +# SPI Master Controller Drivers +# +# CONFIG_SPI_BITBANG is not set +# CONFIG_SPI_GPIO is not set +CONFIG_SPI_OMAP24XX=y + +# +# SPI Protocol Masters +# +# CONFIG_SPI_SPIDEV is not set +# CONFIG_SPI_TLE62X0 is not set + +# +# PPS support +# +# CONFIG_PPS is not set +CONFIG_ARCH_REQUIRE_GPIOLIB=y +CONFIG_GPIOLIB=y +# CONFIG_DEBUG_GPIO is not set +# CONFIG_GPIO_SYSFS is not set + +# +# Memory mapped GPIO expanders: +# + +# +# I2C GPIO expanders: +# +# CONFIG_GPIO_MAX732X is not set +# CONFIG_GPIO_PCA953X is not set +# CONFIG_GPIO_PCF857X is not set +CONFIG_GPIO_TWL4030=y + +# +# PCI GPIO expanders: +# + +# +# SPI GPIO expanders: +# +# CONFIG_GPIO_MAX7301 is not set +# CONFIG_GPIO_MCP23S08 is not set +# CONFIG_GPIO_MC33880 is not set + +# +# AC97 GPIO expanders: +# +CONFIG_W1=y +CONFIG_W1_CON=y + +# +# 1-wire Bus Masters +# +# CONFIG_W1_MASTER_DS2490 is not set +# CONFIG_W1_MASTER_DS2482 is not set +# CONFIG_W1_MASTER_DS1WM is not set +# CONFIG_W1_MASTER_GPIO is not set +# CONFIG_HDQ_MASTER_OMAP is not set + +# +# 1-wire Slaves +# +# CONFIG_W1_SLAVE_THERM is not set +# CONFIG_W1_SLAVE_SMEM is not set +# CONFIG_W1_SLAVE_DS2431 is not set +# CONFIG_W1_SLAVE_DS2433 is not set +# CONFIG_W1_SLAVE_DS2760 is not set +# CONFIG_W1_SLAVE_BQ27000 is not set +CONFIG_POWER_SUPPLY=y +# CONFIG_POWER_SUPPLY_DEBUG is not set +# CONFIG_PDA_POWER is not set +# CONFIG_BATTERY_DS2760 is not set +# CONFIG_BATTERY_DS2782 is not set +# CONFIG_BATTERY_BQ27x00 is not set +# CONFIG_BATTERY_MAX17040 is not set +# CONFIG_HWMON is not set +# CONFIG_THERMAL is not set +CONFIG_WATCHDOG=y +CONFIG_WATCHDOG_NOWAYOUT=y + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set +# CONFIG_OMAP_WATCHDOG is not set +# CONFIG_TWL4030_WATCHDOG is not set + +# +# USB-based Watchdog Cards +# +# CONFIG_USBPCWATCHDOG is not set +CONFIG_SSB_POSSIBLE=y + +# +# Sonics Silicon Backplane +# +# CONFIG_SSB is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_CORE is not set +# CONFIG_MFD_SM501 is not set +# CONFIG_MFD_ASIC3 is not set +# CONFIG_HTC_EGPIO is not set +# CONFIG_HTC_PASIC3 is not set +# CONFIG_TPS65010 is not set +CONFIG_TWL4030_CORE=y +# CONFIG_TWL4030_POWER is not set +# CONFIG_MFD_TMIO is not set +# CONFIG_MFD_T7L66XB is not set +# CONFIG_MFD_TC6387XB is not set +# CONFIG_MFD_TC6393XB is not set +# CONFIG_PMIC_DA903X is not set +# CONFIG_MFD_WM8400 is not set +# CONFIG_MFD_WM831X is not set +# CONFIG_MFD_WM8350_I2C is not set +# CONFIG_MFD_PCF50633 is not set +# CONFIG_MFD_MC13783 is not set +# CONFIG_AB3100_CORE is not set +# CONFIG_EZX_PCAP is not set +CONFIG_REGULATOR=y +# CONFIG_REGULATOR_DEBUG is not set +# CONFIG_REGULATOR_FIXED_VOLTAGE is not set +# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set +# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set +# CONFIG_REGULATOR_BQ24022 is not set +# CONFIG_REGULATOR_MAX1586 is not set +CONFIG_REGULATOR_TWL4030=y +# CONFIG_REGULATOR_LP3971 is not set +# CONFIG_REGULATOR_TPS65023 is not set +# CONFIG_REGULATOR_TPS6507X is not set +# CONFIG_MEDIA_SUPPORT is not set + +# +# Graphics support +# +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=m +# CONFIG_FB is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set + +# +# Console display driver support +# +# CONFIG_VGA_CONSOLE is not set +CONFIG_DUMMY_CONSOLE=y +CONFIG_SOUND=y +# CONFIG_SOUND_OSS_CORE is not set +CONFIG_SND=y +# CONFIG_SND_SEQUENCER is not set +# CONFIG_SND_MIXER_OSS is not set +# CONFIG_SND_PCM_OSS is not set +# CONFIG_SND_HRTIMER is not set +# CONFIG_SND_DYNAMIC_MINORS is not set +CONFIG_SND_SUPPORT_OLD_API=y +CONFIG_SND_VERBOSE_PROCFS=y +# CONFIG_SND_VERBOSE_PRINTK is not set +# CONFIG_SND_DEBUG is not set +# CONFIG_SND_RAWMIDI_SEQ is not set +# CONFIG_SND_OPL3_LIB_SEQ is not set +# CONFIG_SND_OPL4_LIB_SEQ is not set +# CONFIG_SND_SBAWE_SEQ is not set +# CONFIG_SND_EMU10K1_SEQ is not set +CONFIG_SND_DRIVERS=y +# CONFIG_SND_DUMMY is not set +# CONFIG_SND_MTPAV is not set +# CONFIG_SND_SERIAL_U16550 is not set +# CONFIG_SND_MPU401 is not set +CONFIG_SND_ARM=y +CONFIG_SND_SPI=y +CONFIG_SND_USB=y +# CONFIG_SND_USB_AUDIO is not set +# CONFIG_SND_USB_CAIAQ is not set +# CONFIG_SND_SOC is not set +# CONFIG_SOUND_PRIME is not set +CONFIG_HID_SUPPORT=y +CONFIG_HID=y +# CONFIG_HIDRAW is not set + +# +# USB Input Devices +# +CONFIG_USB_HID=y +# CONFIG_HID_PID is not set +# CONFIG_USB_HIDDEV is not set + +# +# Special HID drivers +# +# CONFIG_HID_A4TECH is not set +# CONFIG_HID_APPLE is not set +# CONFIG_HID_BELKIN is not set +# CONFIG_HID_CHERRY is not set +# CONFIG_HID_CHICONY is not set +# CONFIG_HID_CYPRESS is not set +# CONFIG_HID_DRAGONRISE is not set +# CONFIG_HID_EZKEY is not set +# CONFIG_HID_KYE is not set +# CONFIG_HID_GYRATION is not set +# CONFIG_HID_TWINHAN is not set +# CONFIG_HID_KENSINGTON is not set +# CONFIG_HID_LOGITECH is not set +# CONFIG_HID_MICROSOFT is not set +# CONFIG_HID_MONTEREY is not set +# CONFIG_HID_NTRIG is not set +# CONFIG_HID_PANTHERLORD is not set +# CONFIG_HID_PETALYNX is not set +# CONFIG_HID_SAMSUNG is not set +# CONFIG_HID_SONY is not set +# CONFIG_HID_SUNPLUS is not set +# CONFIG_HID_GREENASIA is not set +# CONFIG_HID_SMARTJOYPLUS is not set +# CONFIG_HID_TOPSEED is not set +# CONFIG_HID_THRUSTMASTER is not set +# CONFIG_HID_ZEROPLUS is not set +CONFIG_USB_SUPPORT=y +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y +CONFIG_USB=y +CONFIG_USB_DEBUG=y +CONFIG_USB_ANNOUNCE_NEW_DEVICES=y + +# +# Miscellaneous USB options +# +# CONFIG_USB_DEVICEFS is not set +CONFIG_USB_DEVICE_CLASS=y +# CONFIG_USB_DYNAMIC_MINORS is not set +CONFIG_USB_SUSPEND=y +CONFIG_USB_OTG=y +# CONFIG_USB_OTG_WHITELIST is not set +# CONFIG_USB_OTG_BLACKLIST_HUB is not set +CONFIG_USB_MON=y +# CONFIG_USB_WUSB is not set +# CONFIG_USB_WUSB_CBAF is not set + +# +# USB Host Controller Drivers +# +# CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_EHCI_HCD is not set +# CONFIG_USB_OXU210HP_HCD is not set +# CONFIG_USB_ISP116X_HCD is not set +# CONFIG_USB_ISP1760_HCD is not set +# CONFIG_USB_ISP1362_HCD is not set +# CONFIG_USB_OHCI_HCD is not set +# CONFIG_USB_SL811_HCD is not set +# CONFIG_USB_R8A66597_HCD is not set +# CONFIG_USB_HWA_HCD is not set +CONFIG_USB_MUSB_HDRC=y +CONFIG_USB_MUSB_SOC=y + +# +# OMAP 343x high speed USB support +# +# CONFIG_USB_MUSB_HOST is not set +# CONFIG_USB_MUSB_PERIPHERAL is not set +CONFIG_USB_MUSB_OTG=y +CONFIG_USB_GADGET_MUSB_HDRC=y +CONFIG_USB_MUSB_HDRC_HCD=y +# CONFIG_MUSB_PIO_ONLY is not set +CONFIG_USB_INVENTRA_DMA=y +# CONFIG_USB_TI_CPPI_DMA is not set +CONFIG_USB_MUSB_DEBUG=y + +# +# USB Device Class drivers +# +# CONFIG_USB_ACM is not set +# CONFIG_USB_PRINTER is not set +# CONFIG_USB_WDM is not set +# CONFIG_USB_TMC is not set + +# +# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may +# + +# +# also be needed; see USB_STORAGE Help for more info +# +CONFIG_USB_STORAGE=y +CONFIG_USB_STORAGE_DEBUG=y +# CONFIG_USB_STORAGE_DATAFAB is not set +# CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_ISD200 is not set +# CONFIG_USB_STORAGE_USBAT is not set +# CONFIG_USB_STORAGE_SDDR09 is not set +# CONFIG_USB_STORAGE_SDDR55 is not set +# CONFIG_USB_STORAGE_JUMPSHOT is not set +# CONFIG_USB_STORAGE_ALAUDA is not set +# CONFIG_USB_STORAGE_ONETOUCH is not set +# CONFIG_USB_STORAGE_KARMA is not set +# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set +# CONFIG_USB_LIBUSUAL is not set + +# +# USB Imaging devices +# +# CONFIG_USB_MDC800 is not set +# CONFIG_USB_MICROTEK is not set + +# +# USB port drivers +# +# CONFIG_USB_SERIAL is not set + +# +# USB Miscellaneous drivers +# +# CONFIG_USB_EMI62 is not set +# CONFIG_USB_EMI26 is not set +# CONFIG_USB_ADUTUX is not set +# CONFIG_USB_SEVSEG is not set +# CONFIG_USB_RIO500 is not set +# CONFIG_USB_LEGOTOWER is not set +# CONFIG_USB_LCD is not set +# CONFIG_USB_BERRY_CHARGE is not set +# CONFIG_USB_LED is not set +# CONFIG_USB_CYPRESS_CY7C63 is not set +# CONFIG_USB_CYTHERM is not set +# CONFIG_USB_IDMOUSE is not set +# CONFIG_USB_FTDI_ELAN is not set +# CONFIG_USB_APPLEDISPLAY is not set +# CONFIG_USB_SISUSBVGA is not set +# CONFIG_USB_LD is not set +# CONFIG_USB_TRANCEVIBRATOR is not set +# CONFIG_USB_IOWARRIOR is not set +# CONFIG_USB_TEST is not set +# CONFIG_USB_ISIGHTFW is not set +# CONFIG_USB_VST is not set +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_DEBUG=y +CONFIG_USB_GADGET_DEBUG_FILES=y +CONFIG_USB_GADGET_VBUS_DRAW=2 +CONFIG_USB_GADGET_SELECTED=y +# CONFIG_USB_GADGET_AT91 is not set +# CONFIG_USB_GADGET_ATMEL_USBA is not set +# CONFIG_USB_GADGET_FSL_USB2 is not set +# CONFIG_USB_GADGET_LH7A40X is not set +# CONFIG_USB_GADGET_OMAP is not set +# CONFIG_USB_GADGET_PXA25X is not set +# CONFIG_USB_GADGET_R8A66597 is not set +# CONFIG_USB_GADGET_PXA27X is not set +# CONFIG_USB_GADGET_S3C_HSOTG is not set +# CONFIG_USB_GADGET_IMX is not set +# CONFIG_USB_GADGET_S3C2410 is not set +# CONFIG_USB_GADGET_M66592 is not set +# CONFIG_USB_GADGET_AMD5536UDC is not set +# CONFIG_USB_GADGET_FSL_QE is not set +# CONFIG_USB_GADGET_CI13XXX is not set +# CONFIG_USB_GADGET_NET2280 is not set +# CONFIG_USB_GADGET_GOKU is not set +# CONFIG_USB_GADGET_LANGWELL is not set +# CONFIG_USB_GADGET_DUMMY_HCD is not set +CONFIG_USB_GADGET_DUALSPEED=y +CONFIG_USB_ZERO=y +# CONFIG_USB_ZERO_HNPTEST is not set +# CONFIG_USB_AUDIO is not set +# CONFIG_USB_ETH is not set +# CONFIG_USB_GADGETFS is not set +# CONFIG_USB_FILE_STORAGE is not set +# CONFIG_USB_G_SERIAL is not set +# CONFIG_USB_MIDI_GADGET is not set +# CONFIG_USB_G_PRINTER is not set +# CONFIG_USB_CDC_COMPOSITE is not set + +# +# OTG and related infrastructure +# +CONFIG_USB_OTG_UTILS=y +# CONFIG_USB_GPIO_VBUS is not set +# CONFIG_ISP1301_OMAP is not set +CONFIG_TWL4030_USB=y +# CONFIG_NOP_USB_XCEIV is not set +CONFIG_MMC=y +# CONFIG_MMC_DEBUG is not set +# CONFIG_MMC_UNSAFE_RESUME is not set + +# +# MMC/SD/SDIO Card Drivers +# +CONFIG_MMC_BLOCK=y +CONFIG_MMC_BLOCK_BOUNCE=y +# CONFIG_SDIO_UART is not set +# CONFIG_MMC_TEST is not set + +# +# MMC/SD/SDIO Host Controller Drivers +# +# CONFIG_MMC_SDHCI is not set +# CONFIG_MMC_OMAP is not set +CONFIG_MMC_OMAP_HS=y +# CONFIG_MMC_AT91 is not set +# CONFIG_MMC_ATMELMCI is not set +# CONFIG_MMC_SPI is not set +# CONFIG_MEMSTICK is not set +# CONFIG_NEW_LEDS is not set +# CONFIG_ACCESSIBILITY is not set +CONFIG_RTC_LIB=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_HCTOSYS=y +CONFIG_RTC_HCTOSYS_DEVICE="rtc0" +# CONFIG_RTC_DEBUG is not set + +# +# RTC interfaces +# +CONFIG_RTC_INTF_SYSFS=y +CONFIG_RTC_INTF_PROC=y +CONFIG_RTC_INTF_DEV=y +# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set +# CONFIG_RTC_DRV_TEST is not set + +# +# I2C RTC drivers +# +# CONFIG_RTC_DRV_DS1307 is not set +# CONFIG_RTC_DRV_DS1374 is not set +# CONFIG_RTC_DRV_DS1672 is not set +# CONFIG_RTC_DRV_MAX6900 is not set +# CONFIG_RTC_DRV_RS5C372 is not set +# CONFIG_RTC_DRV_ISL1208 is not set +# CONFIG_RTC_DRV_X1205 is not set +# CONFIG_RTC_DRV_PCF8563 is not set +# CONFIG_RTC_DRV_PCF8583 is not set +# CONFIG_RTC_DRV_M41T80 is not set +# CONFIG_RTC_DRV_TWL4030 is not set +# CONFIG_RTC_DRV_S35390A is not set +# CONFIG_RTC_DRV_FM3130 is not set +# CONFIG_RTC_DRV_RX8581 is not set +# CONFIG_RTC_DRV_RX8025 is not set + +# +# SPI RTC drivers +# +# CONFIG_RTC_DRV_M41T94 is not set +# CONFIG_RTC_DRV_DS1305 is not set +# CONFIG_RTC_DRV_DS1390 is not set +# CONFIG_RTC_DRV_MAX6902 is not set +# CONFIG_RTC_DRV_R9701 is not set +# CONFIG_RTC_DRV_RS5C348 is not set +# CONFIG_RTC_DRV_DS3234 is not set +# CONFIG_RTC_DRV_PCF2123 is not set + +# +# Platform RTC drivers +# +# CONFIG_RTC_DRV_CMOS is not set +# CONFIG_RTC_DRV_DS1286 is not set +# CONFIG_RTC_DRV_DS1511 is not set +# CONFIG_RTC_DRV_DS1553 is not set +# CONFIG_RTC_DRV_DS1742 is not set +# CONFIG_RTC_DRV_STK17TA8 is not set +# CONFIG_RTC_DRV_M48T86 is not set +# CONFIG_RTC_DRV_M48T35 is not set +# CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_BQ4802 is not set +# CONFIG_RTC_DRV_V3020 is not set + +# +# on-CPU RTC drivers +# +# CONFIG_DMADEVICES is not set +# CONFIG_AUXDISPLAY is not set +# CONFIG_UIO is not set + +# +# TI VLYNQ +# +# CONFIG_STAGING is not set + +# +# CBUS support +# +# CONFIG_CBUS is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +CONFIG_EXT3_FS=y +# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set +# CONFIG_EXT3_FS_XATTR is not set +# CONFIG_EXT4_FS is not set +CONFIG_JBD=y +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +CONFIG_FS_POSIX_ACL=y +# CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set +# CONFIG_OCFS2_FS is not set +# CONFIG_BTRFS_FS is not set +# CONFIG_NILFS2_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y +CONFIG_DNOTIFY=y +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +CONFIG_QUOTA=y +# CONFIG_QUOTA_NETLINK_INTERFACE is not set +CONFIG_PRINT_QUOTA_WARNING=y +CONFIG_QUOTA_TREE=y +# CONFIG_QFMT_V1 is not set +CONFIG_QFMT_V2=y +CONFIG_QUOTACTL=y +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# Caches +# +# CONFIG_FSCACHE is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +CONFIG_FAT_FS=y +CONFIG_MSDOS_FS=y +CONFIG_VFAT_FS=y +CONFIG_FAT_DEFAULT_CODEPAGE=437 +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +# CONFIG_CONFIGFS_FS is not set +CONFIG_MISC_FILESYSTEMS=y +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +# CONFIG_CRAMFS is not set +# CONFIG_SQUASHFS is not set +# CONFIG_VXFS_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_OMFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_ROMFS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set +CONFIG_NETWORK_FILESYSTEMS=y +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +CONFIG_NFS_V3_ACL=y +CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set +CONFIG_ROOT_NFS=y +# CONFIG_NFSD is not set +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_NFS_ACL_SUPPORT=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +CONFIG_SUNRPC_GSS=y +CONFIG_RPCSEC_GSS_KRB5=y +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set + +# +# Partition Types +# +CONFIG_PARTITION_ADVANCED=y +# CONFIG_ACORN_PARTITION is not set +# CONFIG_OSF_PARTITION is not set +# CONFIG_AMIGA_PARTITION is not set +# CONFIG_ATARI_PARTITION is not set +# CONFIG_MAC_PARTITION is not set +CONFIG_MSDOS_PARTITION=y +# CONFIG_BSD_DISKLABEL is not set +# CONFIG_MINIX_SUBPARTITION is not set +# CONFIG_SOLARIS_X86_PARTITION is not set +# CONFIG_UNIXWARE_DISKLABEL is not set +# CONFIG_LDM_PARTITION is not set +# CONFIG_SGI_PARTITION is not set +# CONFIG_ULTRIX_PARTITION is not set +# CONFIG_SUN_PARTITION is not set +# CONFIG_KARMA_PARTITION is not set +# CONFIG_EFI_PARTITION is not set +# CONFIG_SYSV68_PARTITION is not set +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +CONFIG_NLS_CODEPAGE_437=y +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +# CONFIG_NLS_CODEPAGE_850 is not set +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +CONFIG_NLS_ISO8859_1=y +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +# CONFIG_NLS_UTF8 is not set +# CONFIG_DLM is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y +CONFIG_ENABLE_MUST_CHECK=y +CONFIG_FRAME_WARN=1024 +CONFIG_MAGIC_SYSRQ=y +# CONFIG_STRIP_ASM_SYMS is not set +# CONFIG_UNUSED_SYMBOLS is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_HEADERS_CHECK is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_DEBUG_SHIRQ is not set +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set +CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 +CONFIG_DETECT_HUNG_TASK=y +# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set +CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0 +CONFIG_SCHED_DEBUG=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_OBJECTS is not set +# CONFIG_DEBUG_SLAB is not set +# CONFIG_DEBUG_KMEMLEAK is not set +# CONFIG_DEBUG_RT_MUTEXES is not set +# CONFIG_RT_MUTEX_TESTER is not set +# CONFIG_DEBUG_SPINLOCK is not set +CONFIG_DEBUG_MUTEXES=y +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set +# CONFIG_DEBUG_KOBJECT is not set +# CONFIG_DEBUG_BUGVERBOSE is not set +CONFIG_DEBUG_INFO=y +# CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_WRITECOUNT is not set +# CONFIG_DEBUG_MEMORY_INIT is not set +# CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set +# CONFIG_DEBUG_NOTIFIERS is not set +# CONFIG_DEBUG_CREDENTIALS is not set +# CONFIG_BOOT_PRINTK_DELAY is not set +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_RCU_CPU_STALL_DETECTOR is not set +# CONFIG_BACKTRACE_SELF_TEST is not set +# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set +# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set +# CONFIG_FAULT_INJECTION is not set +# CONFIG_LATENCYTOP is not set +# CONFIG_PAGE_POISONING is not set +CONFIG_HAVE_FUNCTION_TRACER=y +CONFIG_TRACING_SUPPORT=y +CONFIG_FTRACE=y +# CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set +# CONFIG_SCHED_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set +# CONFIG_BOOT_TRACER is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set +# CONFIG_STACK_TRACER is not set +# CONFIG_KMEMTRACE is not set +# CONFIG_WORKQUEUE_TRACER is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_SAMPLES is not set +CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_KGDB is not set +CONFIG_ARM_UNWIND=y +# CONFIG_DEBUG_USER is not set +# CONFIG_DEBUG_ERRORS is not set +# CONFIG_DEBUG_STACK_USAGE is not set +# CONFIG_DEBUG_LL is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set +CONFIG_CRYPTO=y + +# +# Crypto core or helper +# +CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_ALGAPI2=y +CONFIG_CRYPTO_AEAD2=y +CONFIG_CRYPTO_BLKCIPHER=y +CONFIG_CRYPTO_BLKCIPHER2=y +CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_HASH2=y +CONFIG_CRYPTO_RNG2=y +CONFIG_CRYPTO_PCOMP=y +CONFIG_CRYPTO_MANAGER=y +CONFIG_CRYPTO_MANAGER2=y +# CONFIG_CRYPTO_GF128MUL is not set +# CONFIG_CRYPTO_NULL is not set +CONFIG_CRYPTO_WORKQUEUE=y +# CONFIG_CRYPTO_CRYPTD is not set +# CONFIG_CRYPTO_AUTHENC is not set +# CONFIG_CRYPTO_TEST is not set + +# +# Authenticated Encryption with Associated Data +# +# CONFIG_CRYPTO_CCM is not set +# CONFIG_CRYPTO_GCM is not set +# CONFIG_CRYPTO_SEQIV is not set + +# +# Block modes +# +CONFIG_CRYPTO_CBC=y +# CONFIG_CRYPTO_CTR is not set +# CONFIG_CRYPTO_CTS is not set +CONFIG_CRYPTO_ECB=m +# CONFIG_CRYPTO_LRW is not set +CONFIG_CRYPTO_PCBC=m +# CONFIG_CRYPTO_XTS is not set + +# +# Hash modes +# +# CONFIG_CRYPTO_HMAC is not set +# CONFIG_CRYPTO_XCBC is not set +# CONFIG_CRYPTO_VMAC is not set + +# +# Digest +# +CONFIG_CRYPTO_CRC32C=y +# CONFIG_CRYPTO_GHASH is not set +# CONFIG_CRYPTO_MD4 is not set +CONFIG_CRYPTO_MD5=y +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_RMD128 is not set +# CONFIG_CRYPTO_RMD160 is not set +# CONFIG_CRYPTO_RMD256 is not set +# CONFIG_CRYPTO_RMD320 is not set +# CONFIG_CRYPTO_SHA1 is not set +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_TGR192 is not set +# CONFIG_CRYPTO_WP512 is not set + +# +# Ciphers +# +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +CONFIG_CRYPTO_DES=y +# CONFIG_CRYPTO_FCRYPT is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_SALSA20 is not set +# CONFIG_CRYPTO_SEED is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_TWOFISH is not set + +# +# Compression +# +# CONFIG_CRYPTO_DEFLATE is not set +# CONFIG_CRYPTO_ZLIB is not set +# CONFIG_CRYPTO_LZO is not set + +# +# Random Number Generation +# +# CONFIG_CRYPTO_ANSI_CPRNG is not set +CONFIG_CRYPTO_HW=y +# CONFIG_BINARY_PRINTF is not set + +# +# Library routines +# +CONFIG_BITREVERSE=y +CONFIG_GENERIC_FIND_LAST_BIT=y +CONFIG_CRC_CCITT=y +# CONFIG_CRC16 is not set +CONFIG_CRC_T10DIF=y +# CONFIG_CRC_ITU_T is not set +CONFIG_CRC32=y +# CONFIG_CRC7 is not set +CONFIG_LIBCRC32C=y +CONFIG_ZLIB_INFLATE=y +CONFIG_DECOMPRESS_GZIP=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y +CONFIG_NLATTR=y -- 1.6.5.1.69.g36942 ^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH 7/8] omap: 3630sdp: introduce 3630 sdp board support 2009-11-03 21:20 ` [PATCH 6/8] omap: zoom3: defconfig creation Vikram Pandita @ 2009-11-03 21:20 ` Vikram Pandita 2009-11-03 21:20 ` [PATCH 8/8] omap: 3630sdp: defconfig creation Vikram Pandita 2009-11-03 22:31 ` [PATCH 7/8] omap: 3630sdp: introduce 3630 sdp board support Nishanth Menon 0 siblings, 2 replies; 16+ messages in thread From: Vikram Pandita @ 2009-11-03 21:20 UTC (permalink / raw) To: linux-omap; +Cc: Vikram Pandita Add 3630SDP board support The board shares the same peripherals as a zoom2 main. So reuse the peripheral file of zoom platform. The RAM part is Hynix memory as as in zoom3. Signed-off-by: Vikram Pandita <vikram.pandita@ti.com> --- arch/arm/mach-omap2/Kconfig | 4 ++ arch/arm/mach-omap2/Makefile | 3 + arch/arm/mach-omap2/board-3630sdp.c | 96 +++++++++++++++++++++++++++++++++++ 3 files changed, 103 insertions(+), 0 deletions(-) create mode 100755 arch/arm/mach-omap2/board-3630sdp.c diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig index 9824775..83551a8 100644 --- a/arch/arm/mach-omap2/Kconfig +++ b/arch/arm/mach-omap2/Kconfig @@ -105,6 +105,10 @@ config MACH_OMAP_ZOOM3 bool "OMAP3630 Zoom3 board" depends on ARCH_OMAP3 && ARCH_OMAP34XX +config MACH_OMAP_3630SDP + bool "OMAP3630 SDP board" + depends on ARCH_OMAP3 && ARCH_OMAP34XX + config MACH_OMAP_4430SDP bool "OMAP 4430 SDP board" depends on ARCH_OMAP4 diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index 712e7fc..90cf2cc 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -79,6 +79,9 @@ obj-$(CONFIG_MACH_OMAP_ZOOM3) += board-zoom3.o \ board-zoom-peripherals.o \ mmc-twl4030.o \ board-zoom-debugboard.o +obj-$(CONFIG_MACH_OMAP_3630SDP) += board-3630sdp.o \ + board-zoom-peripherals.o \ + mmc-twl4030.o obj-$(CONFIG_MACH_CM_T35) += board-cm-t35.o \ mmc-twl4030.o diff --git a/arch/arm/mach-omap2/board-3630sdp.c b/arch/arm/mach-omap2/board-3630sdp.c new file mode 100755 index 0000000..450fcdd --- /dev/null +++ b/arch/arm/mach-omap2/board-3630sdp.c @@ -0,0 +1,96 @@ +/* + * Copyright (C) 2009 Texas Instruments Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/input.h> +#include <linux/gpio.h> + +#include <asm/mach-types.h> +#include <asm/mach/arch.h> + +#include <plat/common.h> +#include <plat/board.h> +#include <plat/gpmc-smc91x.h> +#include <plat/mux.h> +#include <plat/usb.h> + +#include "sdram-hynix-h8mbx00u0mer-0em.h" + +#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) +static struct omap_smc91x_platform_data board_smc91x_data = { + .cs = 3, + .flags = GPMC_MUX_ADD_DATA | IORESOURCE_IRQ_LOWLEVEL, +}; + +static void __init board_smc91x_init(void) +{ + board_smc91x_data.gpio_irq = 158; + gpmc_smc91x_init(&board_smc91x_data); +} +#else +static inline void board_smc91x_init(void) +{ +} +#endif + +static void enable_board_wakeup_source(void) +{ + omap_cfg_reg(AF26_34XX_SYS_NIRQ); /* T2 interrupt line (keypad) */ +} + +static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = { + + .port_mode[0] = EHCI_HCD_OMAP_MODE_PHY, + .port_mode[1] = EHCI_HCD_OMAP_MODE_PHY, + .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN, + + .phy_reset = true, + .reset_gpio_port[0] = 126, + .reset_gpio_port[1] = 61, + .reset_gpio_port[2] = -EINVAL +}; + +static void __init omap_sdp_map_io(void) +{ + omap2_set_globals_343x(); + omap2_map_common_io(); +} + +static struct omap_board_config_kernel sdp_config[] __initdata = { +}; +static void __init omap_sdp_init_irq(void) +{ + omap_board_config = sdp_config; + omap_board_config_size = ARRAY_SIZE(sdp_config); + omap2_init_common_hw(h8mbx00u0mer0em_sdrc_params, + h8mbx00u0mer0em_sdrc_params); + omap_init_irq(); + omap_gpio_init(); +} + +extern void __init zoom_peripherals_init(void); + +static void __init omap_sdp_init(void) +{ + zoom_peripherals_init(); + board_smc91x_init(); + enable_board_wakeup_source(); + usb_ehci_init(&ehci_pdata); +} + +MACHINE_START(OMAP_3630SDP, "OMAP 3630SDP board") + .phys_io = 0x48000000, + .io_pg_offst = ((0xfa000000) >> 18) & 0xfffc, + .boot_params = 0x80000100, + .map_io = omap_sdp_map_io, + .init_irq = omap_sdp_init_irq, + .init_machine = omap_sdp_init, + .timer = &omap_timer, +MACHINE_END -- 1.6.5.1.69.g36942 ^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH 8/8] omap: 3630sdp: defconfig creation 2009-11-03 21:20 ` [PATCH 7/8] omap: 3630sdp: introduce 3630 sdp board support Vikram Pandita @ 2009-11-03 21:20 ` Vikram Pandita 2009-11-03 22:31 ` [PATCH 7/8] omap: 3630sdp: introduce 3630 sdp board support Nishanth Menon 1 sibling, 0 replies; 16+ messages in thread From: Vikram Pandita @ 2009-11-03 21:20 UTC (permalink / raw) To: linux-omap; +Cc: Vikram Pandita Create 3630sdp defconfig file Signed-off-by: Vikram Pandita <vikram.pandita@ti.com> --- arch/arm/configs/omap_3630sdp_defconfig | 1606 +++++++++++++++++++++++++++++++ 1 files changed, 1606 insertions(+), 0 deletions(-) create mode 100644 arch/arm/configs/omap_3630sdp_defconfig diff --git a/arch/arm/configs/omap_3630sdp_defconfig b/arch/arm/configs/omap_3630sdp_defconfig new file mode 100644 index 0000000..eb96b1a --- /dev/null +++ b/arch/arm/configs/omap_3630sdp_defconfig @@ -0,0 +1,1606 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.32-rc5 +# Tue Nov 3 14:18:44 2009 +# +CONFIG_ARM=y +CONFIG_SYS_SUPPORTS_APM_EMULATION=y +CONFIG_GENERIC_GPIO=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_HARDIRQS=y +CONFIG_STACKTRACE_SUPPORT=y +CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_LOCKDEP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_ARCH_HAS_CPUFREQ=y +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y +CONFIG_VECTORS_BASE=0xffff0000 +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y + +# +# General setup +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +CONFIG_SWAP=y +CONFIG_SYSVIPC=y +CONFIG_SYSVIPC_SYSCTL=y +# CONFIG_POSIX_MQUEUE is not set +CONFIG_BSD_PROCESS_ACCT=y +# CONFIG_BSD_PROCESS_ACCT_V3 is not set +# CONFIG_TASKSTATS is not set +# CONFIG_AUDIT is not set + +# +# RCU Subsystem +# +CONFIG_TREE_RCU=y +# CONFIG_TREE_PREEMPT_RCU is not set +# CONFIG_RCU_TRACE is not set +CONFIG_RCU_FANOUT=32 +# CONFIG_RCU_FANOUT_EXACT is not set +# CONFIG_TREE_RCU_TRACE is not set +# CONFIG_IKCONFIG is not set +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_GROUP_SCHED=y +CONFIG_FAIR_GROUP_SCHED=y +# CONFIG_RT_GROUP_SCHED is not set +CONFIG_USER_SCHED=y +# CONFIG_CGROUP_SCHED is not set +# CONFIG_CGROUPS is not set +# CONFIG_SYSFS_DEPRECATED_V2 is not set +# CONFIG_RELAY is not set +# CONFIG_NAMESPACES is not set +CONFIG_BLK_DEV_INITRD=y +CONFIG_INITRAMFS_SOURCE="" +CONFIG_RD_GZIP=y +# CONFIG_RD_BZIP2 is not set +# CONFIG_RD_LZMA is not set +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +CONFIG_SYSCTL=y +CONFIG_ANON_INODES=y +CONFIG_EMBEDDED=y +CONFIG_UID16=y +# CONFIG_SYSCTL_SYSCALL is not set +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +CONFIG_KALLSYMS_EXTRA_PASS=y +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_TIMERFD=y +CONFIG_EVENTFD=y +CONFIG_SHMEM=y +CONFIG_AIO=y + +# +# Kernel Performance Events And Counters +# +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_COMPAT_BRK=y +CONFIG_SLAB=y +# CONFIG_SLUB is not set +# CONFIG_SLOB is not set +# CONFIG_PROFILING is not set +CONFIG_HAVE_OPROFILE=y +# CONFIG_KPROBES is not set +CONFIG_HAVE_KPROBES=y +CONFIG_HAVE_KRETPROBES=y +CONFIG_HAVE_CLK=y + +# +# GCOV-based kernel profiling +# +# CONFIG_SLOW_WORK is not set +CONFIG_HAVE_GENERIC_DMA_COHERENT=y +CONFIG_SLABINFO=y +CONFIG_RT_MUTEXES=y +CONFIG_BASE_SMALL=0 +CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +CONFIG_MODVERSIONS=y +CONFIG_MODULE_SRCVERSION_ALL=y +CONFIG_BLOCK=y +CONFIG_LBDAF=y +# CONFIG_BLK_DEV_BSG is not set +# CONFIG_BLK_DEV_INTEGRITY is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" +CONFIG_FREEZER=y + +# +# System Type +# +CONFIG_MMU=y +# CONFIG_ARCH_AAEC2000 is not set +# CONFIG_ARCH_INTEGRATOR is not set +# CONFIG_ARCH_REALVIEW is not set +# CONFIG_ARCH_VERSATILE is not set +# CONFIG_ARCH_AT91 is not set +# CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_GEMINI is not set +# CONFIG_ARCH_EBSA110 is not set +# CONFIG_ARCH_EP93XX is not set +# CONFIG_ARCH_FOOTBRIDGE is not set +# CONFIG_ARCH_MXC is not set +# CONFIG_ARCH_STMP3XXX is not set +# CONFIG_ARCH_NETX is not set +# CONFIG_ARCH_H720X is not set +# CONFIG_ARCH_NOMADIK is not set +# CONFIG_ARCH_IOP13XX is not set +# CONFIG_ARCH_IOP32X is not set +# CONFIG_ARCH_IOP33X is not set +# CONFIG_ARCH_IXP23XX is not set +# CONFIG_ARCH_IXP2000 is not set +# CONFIG_ARCH_IXP4XX is not set +# CONFIG_ARCH_L7200 is not set +# CONFIG_ARCH_KIRKWOOD is not set +# CONFIG_ARCH_LOKI is not set +# CONFIG_ARCH_MV78XX0 is not set +# CONFIG_ARCH_ORION5X is not set +# CONFIG_ARCH_MMP is not set +# CONFIG_ARCH_KS8695 is not set +# CONFIG_ARCH_NS9XXX is not set +# CONFIG_ARCH_W90X900 is not set +# CONFIG_ARCH_PNX4008 is not set +# CONFIG_ARCH_PXA is not set +# CONFIG_ARCH_MSM is not set +# CONFIG_ARCH_RPC is not set +# CONFIG_ARCH_SA1100 is not set +# CONFIG_ARCH_S3C2410 is not set +# CONFIG_ARCH_S3C64XX is not set +# CONFIG_ARCH_S5PC1XX is not set +# CONFIG_ARCH_SHARK is not set +# CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_U300 is not set +# CONFIG_ARCH_DAVINCI is not set +CONFIG_ARCH_OMAP=y +# CONFIG_ARCH_BCMRING is not set + +# +# TI OMAP Implementations +# +CONFIG_ARCH_OMAP_OTG=y +# CONFIG_ARCH_OMAP1 is not set +# CONFIG_ARCH_OMAP2 is not set +CONFIG_ARCH_OMAP3=y +# CONFIG_ARCH_OMAP4 is not set + +# +# OMAP Feature Selections +# +# CONFIG_OMAP_DEBUG_POWERDOMAIN is not set +# CONFIG_OMAP_DEBUG_CLOCKDOMAIN is not set +# CONFIG_OMAP_RESET_CLOCKS is not set +CONFIG_OMAP_MUX=y +CONFIG_OMAP_MUX_DEBUG=y +CONFIG_OMAP_MUX_WARNINGS=y +CONFIG_OMAP_MCBSP=y +# CONFIG_OMAP_MBOX_FWK is not set +# CONFIG_OMAP_MPU_TIMER is not set +CONFIG_OMAP_32K_TIMER=y +CONFIG_OMAP_32K_TIMER_HZ=128 +CONFIG_OMAP_DM_TIMER=y +CONFIG_OMAP_LL_DEBUG_UART1=y +# CONFIG_OMAP_LL_DEBUG_UART2 is not set +# CONFIG_OMAP_LL_DEBUG_UART3 is not set +# CONFIG_OMAP_LL_DEBUG_NONE is not set +# CONFIG_OMAP_PM_NONE is not set +CONFIG_OMAP_PM_NOOP=y +CONFIG_ARCH_OMAP34XX=y +CONFIG_ARCH_OMAP3430=y + +# +# OMAP Board Type +# +# CONFIG_MACH_OMAP3_BEAGLE is not set +# CONFIG_MACH_OMAP_LDP is not set +# CONFIG_MACH_OVERO is not set +# CONFIG_MACH_OMAP3EVM is not set +# CONFIG_MACH_OMAP3_PANDORA is not set +# CONFIG_MACH_OMAP_3430SDP is not set +# CONFIG_MACH_NOKIA_RX51 is not set +# CONFIG_MACH_OMAP_ZOOM2 is not set +# CONFIG_MACH_CM_T35 is not set +# CONFIG_MACH_OMAP_ZOOM3 is not set +CONFIG_MACH_OMAP_3630SDP=y + +# +# Processor Type +# +CONFIG_CPU_32=y +CONFIG_CPU_32v6K=y +CONFIG_CPU_V7=y +CONFIG_CPU_32v7=y +CONFIG_CPU_ABRT_EV7=y +CONFIG_CPU_PABRT_V7=y +CONFIG_CPU_CACHE_V7=y +CONFIG_CPU_CACHE_VIPT=y +CONFIG_CPU_COPY_V6=y +CONFIG_CPU_TLB_V7=y +CONFIG_CPU_HAS_ASID=y +CONFIG_CPU_CP15=y +CONFIG_CPU_CP15_MMU=y + +# +# Processor Features +# +CONFIG_ARM_THUMB=y +# CONFIG_ARM_THUMBEE is not set +# CONFIG_CPU_ICACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_DISABLE is not set +# CONFIG_CPU_BPREDICT_DISABLE is not set +CONFIG_HAS_TLS_REG=y +CONFIG_ARM_L1_CACHE_SHIFT=6 +# CONFIG_ARM_ERRATA_430973 is not set +# CONFIG_ARM_ERRATA_458693 is not set +# CONFIG_ARM_ERRATA_460075 is not set +CONFIG_COMMON_CLKDEV=y + +# +# Bus support +# +# CONFIG_PCI_SYSCALL is not set +# CONFIG_ARCH_SUPPORTS_MSI is not set +# CONFIG_PCCARD is not set + +# +# Kernel Features +# +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +CONFIG_VMSPLIT_3G=y +# CONFIG_VMSPLIT_2G is not set +# CONFIG_VMSPLIT_1G is not set +CONFIG_PAGE_OFFSET=0xC0000000 +CONFIG_PREEMPT_NONE=y +# CONFIG_PREEMPT_VOLUNTARY is not set +# CONFIG_PREEMPT is not set +CONFIG_HZ=128 +# CONFIG_THUMB2_KERNEL is not set +CONFIG_AEABI=y +CONFIG_OABI_COMPAT=y +# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set +# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set +# CONFIG_HIGHMEM is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +CONFIG_PAGEFLAGS_EXTENDED=y +CONFIG_SPLIT_PTLOCK_CPUS=4 +# CONFIG_PHYS_ADDR_T_64BIT is not set +CONFIG_ZONE_DMA_FLAG=0 +CONFIG_VIRT_TO_BUS=y +CONFIG_HAVE_MLOCK=y +CONFIG_HAVE_MLOCKED_PAGE_BIT=y +# CONFIG_KSM is not set +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 +# CONFIG_LEDS is not set +CONFIG_ALIGNMENT_TRAP=y +# CONFIG_UACCESS_WITH_MEMCPY is not set + +# +# Boot options +# +CONFIG_ZBOOT_ROM_TEXT=0x0 +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_CMDLINE="root=/dev/nfs nfsroot=192.168.0.1:/home/user/buildroot ip=192.168.0.2:192.168.0.1:192.168.0.1:255.255.255.0:tgt:eth0:off rw console=ttyS2,115200n8" +# CONFIG_XIP_KERNEL is not set +# CONFIG_KEXEC is not set + +# +# CPU Power Management +# +# CONFIG_CPU_FREQ is not set +# CONFIG_CPU_IDLE is not set + +# +# Floating point emulation +# + +# +# At least one emulation must be selected +# +CONFIG_FPE_NWFPE=y +# CONFIG_FPE_NWFPE_XP is not set +# CONFIG_FPE_FASTFPE is not set +CONFIG_VFP=y +CONFIG_VFPv3=y +# CONFIG_NEON is not set + +# +# Userspace binary formats +# +CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +CONFIG_HAVE_AOUT=y +# CONFIG_BINFMT_AOUT is not set +CONFIG_BINFMT_MISC=y + +# +# Power management options +# +CONFIG_PM=y +CONFIG_PM_DEBUG=y +CONFIG_PM_VERBOSE=y +CONFIG_CAN_PM_TRACE=y +CONFIG_PM_SLEEP=y +CONFIG_SUSPEND=y +# CONFIG_PM_TEST_SUSPEND is not set +CONFIG_SUSPEND_FREEZER=y +# CONFIG_APM_EMULATION is not set +# CONFIG_PM_RUNTIME is not set +CONFIG_ARCH_SUSPEND_POSSIBLE=y +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +CONFIG_XFRM=y +CONFIG_XFRM_USER=y +# CONFIG_XFRM_SUB_POLICY is not set +CONFIG_XFRM_MIGRATE=y +# CONFIG_XFRM_STATISTICS is not set +CONFIG_NET_KEY=y +CONFIG_NET_KEY_MIGRATE=y +CONFIG_INET=y +CONFIG_IP_MULTICAST=y +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +CONFIG_IP_PNP_RARP=y +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_IP_MROUTE is not set +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set +CONFIG_INET_XFRM_MODE_TRANSPORT=y +CONFIG_INET_XFRM_MODE_TUNNEL=y +CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +# CONFIG_IPV6 is not set +# CONFIG_NETWORK_SECMARK is not set +# CONFIG_NETFILTER is not set +# CONFIG_IP_DCCP is not set +# CONFIG_IP_SCTP is not set +# CONFIG_RDS is not set +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set +# CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set +# CONFIG_NET_SCHED is not set +# CONFIG_DCB is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_CAN is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_AF_RXRPC is not set +# CONFIG_WIRELESS is not set +# CONFIG_WIMAX is not set +# CONFIG_RFKILL is not set +# CONFIG_NET_9P is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +# CONFIG_DEVTMPFS is not set +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_FW_LOADER is not set +# CONFIG_DEBUG_DRIVER is not set +# CONFIG_DEBUG_DEVRES is not set +# CONFIG_SYS_HYPERVISOR is not set +CONFIG_CONNECTOR=y +CONFIG_PROC_EVENTS=y +# CONFIG_MTD is not set +# CONFIG_PARPORT is not set +CONFIG_BLK_DEV=y +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=y +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +# CONFIG_BLK_DEV_NBD is not set +# CONFIG_BLK_DEV_UB is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=16384 +# CONFIG_BLK_DEV_XIP is not set +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set +# CONFIG_MG_DISK is not set +CONFIG_MISC_DEVICES=y +# CONFIG_ICS932S401 is not set +# CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_ISL29003 is not set +# CONFIG_C2PORT is not set + +# +# EEPROM support +# +# CONFIG_EEPROM_AT24 is not set +# CONFIG_EEPROM_AT25 is not set +# CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set +# CONFIG_EEPROM_93CX6 is not set +CONFIG_HAVE_IDE=y +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +CONFIG_SCSI=y +CONFIG_SCSI_DMA=y +# CONFIG_SCSI_TGT is not set +# CONFIG_SCSI_NETLINK is not set +CONFIG_SCSI_PROC_FS=y + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=y +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set +# CONFIG_BLK_DEV_SR is not set +# CONFIG_CHR_DEV_SG is not set +# CONFIG_CHR_DEV_SCH is not set +# CONFIG_SCSI_MULTI_LUN is not set +# CONFIG_SCSI_CONSTANTS is not set +# CONFIG_SCSI_LOGGING is not set +# CONFIG_SCSI_SCAN_ASYNC is not set +CONFIG_SCSI_WAIT_SCAN=m + +# +# SCSI Transports +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set +CONFIG_SCSI_LOWLEVEL=y +# CONFIG_ISCSI_TCP is not set +# CONFIG_LIBFC is not set +# CONFIG_LIBFCOE is not set +# CONFIG_SCSI_DEBUG is not set +# CONFIG_SCSI_DH is not set +# CONFIG_SCSI_OSD_INITIATOR is not set +# CONFIG_ATA is not set +# CONFIG_MD is not set +CONFIG_NETDEVICES=y +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_MACVLAN is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set +# CONFIG_VETH is not set +CONFIG_PHYLIB=y + +# +# MII PHY device drivers +# +# CONFIG_MARVELL_PHY is not set +# CONFIG_DAVICOM_PHY is not set +# CONFIG_QSEMI_PHY is not set +# CONFIG_LXT_PHY is not set +# CONFIG_CICADA_PHY is not set +# CONFIG_VITESSE_PHY is not set +CONFIG_SMSC_PHY=y +# CONFIG_BROADCOM_PHY is not set +# CONFIG_ICPLUS_PHY is not set +# CONFIG_REALTEK_PHY is not set +# CONFIG_NATIONAL_PHY is not set +# CONFIG_STE10XP is not set +# CONFIG_LSI_ET1011C_PHY is not set +# CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +# CONFIG_AX88796 is not set +CONFIG_SMC91X=y +# CONFIG_DM9000 is not set +# CONFIG_ENC28J60 is not set +# CONFIG_ETHOC is not set +# CONFIG_SMC911X is not set +# CONFIG_SMSC911X is not set +# CONFIG_DNET is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set +# CONFIG_B44 is not set +# CONFIG_KS8842 is not set +# CONFIG_KS8851 is not set +# CONFIG_KS8851_MLL is not set +CONFIG_NETDEV_1000=y +CONFIG_NETDEV_10000=y +CONFIG_WLAN=y +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set + +# +# Enable WiMAX (Networking options) to see the WiMAX drivers +# + +# +# USB Network Adapters +# +# CONFIG_USB_CATC is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_RTL8150 is not set +# CONFIG_USB_USBNET is not set +# CONFIG_WAN is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set +# CONFIG_ISDN is not set +# CONFIG_PHONE is not set + +# +# Input device support +# +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set +# CONFIG_INPUT_POLLDEV is not set + +# +# Userland interfaces +# +# CONFIG_INPUT_MOUSEDEV is not set +# CONFIG_INPUT_JOYDEV is not set +CONFIG_INPUT_EVDEV=y +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TABLET is not set +CONFIG_INPUT_TOUCHSCREEN=y +CONFIG_TOUCHSCREEN_ADS7846=y +# CONFIG_TOUCHSCREEN_AD7877 is not set +# CONFIG_TOUCHSCREEN_AD7879_I2C is not set +# CONFIG_TOUCHSCREEN_AD7879_SPI is not set +# CONFIG_TOUCHSCREEN_AD7879 is not set +# CONFIG_TOUCHSCREEN_EETI is not set +# CONFIG_TOUCHSCREEN_FUJITSU is not set +# CONFIG_TOUCHSCREEN_GUNZE is not set +# CONFIG_TOUCHSCREEN_ELO is not set +# CONFIG_TOUCHSCREEN_WACOM_W8001 is not set +# CONFIG_TOUCHSCREEN_MCS5000 is not set +# CONFIG_TOUCHSCREEN_MTOUCH is not set +# CONFIG_TOUCHSCREEN_INEXIO is not set +# CONFIG_TOUCHSCREEN_MK712 is not set +# CONFIG_TOUCHSCREEN_PENMOUNT is not set +# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set +# CONFIG_TOUCHSCREEN_TOUCHWIN is not set +# CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set +# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set +# CONFIG_TOUCHSCREEN_TSC2007 is not set +# CONFIG_TOUCHSCREEN_W90X900 is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_CONSOLE_TRANSLATIONS=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_VT_HW_CONSOLE_BINDING is not set +CONFIG_DEVKMEM=y +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_NR_UARTS=32 +CONFIG_SERIAL_8250_RUNTIME_UARTS=4 +CONFIG_SERIAL_8250_EXTENDED=y +CONFIG_SERIAL_8250_MANY_PORTS=y +CONFIG_SERIAL_8250_SHARE_IRQ=y +CONFIG_SERIAL_8250_DETECT_IRQ=y +CONFIG_SERIAL_8250_RSA=y + +# +# Non-8250 serial port support +# +# CONFIG_SERIAL_MAX3100 is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_UNIX98_PTYS=y +# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set +# CONFIG_LEGACY_PTYS is not set +# CONFIG_IPMI_HANDLER is not set +CONFIG_HW_RANDOM=y +# CONFIG_HW_RANDOM_TIMERIOMEM is not set +# CONFIG_R3964 is not set +# CONFIG_RAW_DRIVER is not set +# CONFIG_TCG_TPM is not set +CONFIG_I2C=y +CONFIG_I2C_BOARDINFO=y +CONFIG_I2C_COMPAT=y +CONFIG_I2C_CHARDEV=y +CONFIG_I2C_HELPER_AUTO=y + +# +# I2C Hardware Bus support +# + +# +# I2C system bus drivers (mostly embedded / system-on-chip) +# +# CONFIG_I2C_DESIGNWARE is not set +# CONFIG_I2C_GPIO is not set +# CONFIG_I2C_OCORES is not set +CONFIG_I2C_OMAP=y +# CONFIG_I2C_SIMTEC is not set + +# +# External I2C/SMBus adapter drivers +# +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_TAOS_EVM is not set +# CONFIG_I2C_TINY_USB is not set + +# +# Other I2C/SMBus bus drivers +# +# CONFIG_I2C_PCA_PLATFORM is not set +# CONFIG_I2C_STUB is not set + +# +# Miscellaneous I2C Chip support +# +# CONFIG_DS1682 is not set +# CONFIG_SENSORS_TSL2550 is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set +CONFIG_SPI=y +# CONFIG_SPI_DEBUG is not set +CONFIG_SPI_MASTER=y + +# +# SPI Master Controller Drivers +# +# CONFIG_SPI_BITBANG is not set +# CONFIG_SPI_GPIO is not set +CONFIG_SPI_OMAP24XX=y + +# +# SPI Protocol Masters +# +# CONFIG_SPI_SPIDEV is not set +# CONFIG_SPI_TLE62X0 is not set + +# +# PPS support +# +# CONFIG_PPS is not set +CONFIG_ARCH_REQUIRE_GPIOLIB=y +CONFIG_GPIOLIB=y +# CONFIG_DEBUG_GPIO is not set +# CONFIG_GPIO_SYSFS is not set + +# +# Memory mapped GPIO expanders: +# + +# +# I2C GPIO expanders: +# +# CONFIG_GPIO_MAX732X is not set +# CONFIG_GPIO_PCA953X is not set +# CONFIG_GPIO_PCF857X is not set +CONFIG_GPIO_TWL4030=y + +# +# PCI GPIO expanders: +# + +# +# SPI GPIO expanders: +# +# CONFIG_GPIO_MAX7301 is not set +# CONFIG_GPIO_MCP23S08 is not set +# CONFIG_GPIO_MC33880 is not set + +# +# AC97 GPIO expanders: +# +CONFIG_W1=y +CONFIG_W1_CON=y + +# +# 1-wire Bus Masters +# +# CONFIG_W1_MASTER_DS2490 is not set +# CONFIG_W1_MASTER_DS2482 is not set +# CONFIG_W1_MASTER_DS1WM is not set +# CONFIG_W1_MASTER_GPIO is not set +# CONFIG_HDQ_MASTER_OMAP is not set + +# +# 1-wire Slaves +# +# CONFIG_W1_SLAVE_THERM is not set +# CONFIG_W1_SLAVE_SMEM is not set +# CONFIG_W1_SLAVE_DS2431 is not set +# CONFIG_W1_SLAVE_DS2433 is not set +# CONFIG_W1_SLAVE_DS2760 is not set +# CONFIG_W1_SLAVE_BQ27000 is not set +CONFIG_POWER_SUPPLY=y +# CONFIG_POWER_SUPPLY_DEBUG is not set +# CONFIG_PDA_POWER is not set +# CONFIG_BATTERY_DS2760 is not set +# CONFIG_BATTERY_DS2782 is not set +# CONFIG_BATTERY_BQ27x00 is not set +# CONFIG_BATTERY_MAX17040 is not set +# CONFIG_HWMON is not set +# CONFIG_THERMAL is not set +CONFIG_WATCHDOG=y +CONFIG_WATCHDOG_NOWAYOUT=y + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set +# CONFIG_OMAP_WATCHDOG is not set +# CONFIG_TWL4030_WATCHDOG is not set + +# +# USB-based Watchdog Cards +# +# CONFIG_USBPCWATCHDOG is not set +CONFIG_SSB_POSSIBLE=y + +# +# Sonics Silicon Backplane +# +# CONFIG_SSB is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_CORE is not set +# CONFIG_MFD_SM501 is not set +# CONFIG_MFD_ASIC3 is not set +# CONFIG_HTC_EGPIO is not set +# CONFIG_HTC_PASIC3 is not set +# CONFIG_TPS65010 is not set +CONFIG_TWL4030_CORE=y +# CONFIG_TWL4030_POWER is not set +# CONFIG_MFD_TMIO is not set +# CONFIG_MFD_T7L66XB is not set +# CONFIG_MFD_TC6387XB is not set +# CONFIG_MFD_TC6393XB is not set +# CONFIG_PMIC_DA903X is not set +# CONFIG_MFD_WM8400 is not set +# CONFIG_MFD_WM831X is not set +# CONFIG_MFD_WM8350_I2C is not set +# CONFIG_MFD_PCF50633 is not set +# CONFIG_MFD_MC13783 is not set +# CONFIG_AB3100_CORE is not set +# CONFIG_EZX_PCAP is not set +CONFIG_REGULATOR=y +# CONFIG_REGULATOR_DEBUG is not set +# CONFIG_REGULATOR_FIXED_VOLTAGE is not set +# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set +# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set +# CONFIG_REGULATOR_BQ24022 is not set +# CONFIG_REGULATOR_MAX1586 is not set +CONFIG_REGULATOR_TWL4030=y +# CONFIG_REGULATOR_LP3971 is not set +# CONFIG_REGULATOR_TPS65023 is not set +# CONFIG_REGULATOR_TPS6507X is not set +# CONFIG_MEDIA_SUPPORT is not set + +# +# Graphics support +# +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=m +# CONFIG_FB is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set + +# +# Console display driver support +# +# CONFIG_VGA_CONSOLE is not set +CONFIG_DUMMY_CONSOLE=y +CONFIG_SOUND=y +# CONFIG_SOUND_OSS_CORE is not set +CONFIG_SND=y +# CONFIG_SND_SEQUENCER is not set +# CONFIG_SND_MIXER_OSS is not set +# CONFIG_SND_PCM_OSS is not set +# CONFIG_SND_HRTIMER is not set +# CONFIG_SND_DYNAMIC_MINORS is not set +CONFIG_SND_SUPPORT_OLD_API=y +CONFIG_SND_VERBOSE_PROCFS=y +# CONFIG_SND_VERBOSE_PRINTK is not set +# CONFIG_SND_DEBUG is not set +# CONFIG_SND_RAWMIDI_SEQ is not set +# CONFIG_SND_OPL3_LIB_SEQ is not set +# CONFIG_SND_OPL4_LIB_SEQ is not set +# CONFIG_SND_SBAWE_SEQ is not set +# CONFIG_SND_EMU10K1_SEQ is not set +CONFIG_SND_DRIVERS=y +# CONFIG_SND_DUMMY is not set +# CONFIG_SND_MTPAV is not set +# CONFIG_SND_SERIAL_U16550 is not set +# CONFIG_SND_MPU401 is not set +CONFIG_SND_ARM=y +CONFIG_SND_SPI=y +CONFIG_SND_USB=y +# CONFIG_SND_USB_AUDIO is not set +# CONFIG_SND_USB_CAIAQ is not set +# CONFIG_SND_SOC is not set +# CONFIG_SOUND_PRIME is not set +CONFIG_HID_SUPPORT=y +CONFIG_HID=y +# CONFIG_HIDRAW is not set + +# +# USB Input Devices +# +CONFIG_USB_HID=y +# CONFIG_HID_PID is not set +# CONFIG_USB_HIDDEV is not set + +# +# Special HID drivers +# +# CONFIG_HID_A4TECH is not set +# CONFIG_HID_APPLE is not set +# CONFIG_HID_BELKIN is not set +# CONFIG_HID_CHERRY is not set +# CONFIG_HID_CHICONY is not set +# CONFIG_HID_CYPRESS is not set +# CONFIG_HID_DRAGONRISE is not set +# CONFIG_HID_EZKEY is not set +# CONFIG_HID_KYE is not set +# CONFIG_HID_GYRATION is not set +# CONFIG_HID_TWINHAN is not set +# CONFIG_HID_KENSINGTON is not set +# CONFIG_HID_LOGITECH is not set +# CONFIG_HID_MICROSOFT is not set +# CONFIG_HID_MONTEREY is not set +# CONFIG_HID_NTRIG is not set +# CONFIG_HID_PANTHERLORD is not set +# CONFIG_HID_PETALYNX is not set +# CONFIG_HID_SAMSUNG is not set +# CONFIG_HID_SONY is not set +# CONFIG_HID_SUNPLUS is not set +# CONFIG_HID_GREENASIA is not set +# CONFIG_HID_SMARTJOYPLUS is not set +# CONFIG_HID_TOPSEED is not set +# CONFIG_HID_THRUSTMASTER is not set +# CONFIG_HID_ZEROPLUS is not set +CONFIG_USB_SUPPORT=y +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y +CONFIG_USB=y +CONFIG_USB_DEBUG=y +CONFIG_USB_ANNOUNCE_NEW_DEVICES=y + +# +# Miscellaneous USB options +# +# CONFIG_USB_DEVICEFS is not set +CONFIG_USB_DEVICE_CLASS=y +# CONFIG_USB_DYNAMIC_MINORS is not set +CONFIG_USB_SUSPEND=y +CONFIG_USB_OTG=y +# CONFIG_USB_OTG_WHITELIST is not set +# CONFIG_USB_OTG_BLACKLIST_HUB is not set +CONFIG_USB_MON=y +# CONFIG_USB_WUSB is not set +# CONFIG_USB_WUSB_CBAF is not set + +# +# USB Host Controller Drivers +# +# CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_EHCI_HCD is not set +# CONFIG_USB_OXU210HP_HCD is not set +# CONFIG_USB_ISP116X_HCD is not set +# CONFIG_USB_ISP1760_HCD is not set +# CONFIG_USB_ISP1362_HCD is not set +# CONFIG_USB_OHCI_HCD is not set +# CONFIG_USB_SL811_HCD is not set +# CONFIG_USB_R8A66597_HCD is not set +# CONFIG_USB_HWA_HCD is not set +CONFIG_USB_MUSB_HDRC=y +CONFIG_USB_MUSB_SOC=y + +# +# OMAP 343x high speed USB support +# +# CONFIG_USB_MUSB_HOST is not set +# CONFIG_USB_MUSB_PERIPHERAL is not set +CONFIG_USB_MUSB_OTG=y +CONFIG_USB_GADGET_MUSB_HDRC=y +CONFIG_USB_MUSB_HDRC_HCD=y +# CONFIG_MUSB_PIO_ONLY is not set +CONFIG_USB_INVENTRA_DMA=y +# CONFIG_USB_TI_CPPI_DMA is not set +CONFIG_USB_MUSB_DEBUG=y + +# +# USB Device Class drivers +# +# CONFIG_USB_ACM is not set +# CONFIG_USB_PRINTER is not set +# CONFIG_USB_WDM is not set +# CONFIG_USB_TMC is not set + +# +# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may +# + +# +# also be needed; see USB_STORAGE Help for more info +# +CONFIG_USB_STORAGE=y +CONFIG_USB_STORAGE_DEBUG=y +# CONFIG_USB_STORAGE_DATAFAB is not set +# CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_ISD200 is not set +# CONFIG_USB_STORAGE_USBAT is not set +# CONFIG_USB_STORAGE_SDDR09 is not set +# CONFIG_USB_STORAGE_SDDR55 is not set +# CONFIG_USB_STORAGE_JUMPSHOT is not set +# CONFIG_USB_STORAGE_ALAUDA is not set +# CONFIG_USB_STORAGE_ONETOUCH is not set +# CONFIG_USB_STORAGE_KARMA is not set +# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set +# CONFIG_USB_LIBUSUAL is not set + +# +# USB Imaging devices +# +# CONFIG_USB_MDC800 is not set +# CONFIG_USB_MICROTEK is not set + +# +# USB port drivers +# +# CONFIG_USB_SERIAL is not set + +# +# USB Miscellaneous drivers +# +# CONFIG_USB_EMI62 is not set +# CONFIG_USB_EMI26 is not set +# CONFIG_USB_ADUTUX is not set +# CONFIG_USB_SEVSEG is not set +# CONFIG_USB_RIO500 is not set +# CONFIG_USB_LEGOTOWER is not set +# CONFIG_USB_LCD is not set +# CONFIG_USB_BERRY_CHARGE is not set +# CONFIG_USB_LED is not set +# CONFIG_USB_CYPRESS_CY7C63 is not set +# CONFIG_USB_CYTHERM is not set +# CONFIG_USB_IDMOUSE is not set +# CONFIG_USB_FTDI_ELAN is not set +# CONFIG_USB_APPLEDISPLAY is not set +# CONFIG_USB_SISUSBVGA is not set +# CONFIG_USB_LD is not set +# CONFIG_USB_TRANCEVIBRATOR is not set +# CONFIG_USB_IOWARRIOR is not set +# CONFIG_USB_TEST is not set +# CONFIG_USB_ISIGHTFW is not set +# CONFIG_USB_VST is not set +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_DEBUG=y +CONFIG_USB_GADGET_DEBUG_FILES=y +CONFIG_USB_GADGET_VBUS_DRAW=2 +CONFIG_USB_GADGET_SELECTED=y +# CONFIG_USB_GADGET_AT91 is not set +# CONFIG_USB_GADGET_ATMEL_USBA is not set +# CONFIG_USB_GADGET_FSL_USB2 is not set +# CONFIG_USB_GADGET_LH7A40X is not set +# CONFIG_USB_GADGET_OMAP is not set +# CONFIG_USB_GADGET_PXA25X is not set +# CONFIG_USB_GADGET_R8A66597 is not set +# CONFIG_USB_GADGET_PXA27X is not set +# CONFIG_USB_GADGET_S3C_HSOTG is not set +# CONFIG_USB_GADGET_IMX is not set +# CONFIG_USB_GADGET_S3C2410 is not set +# CONFIG_USB_GADGET_M66592 is not set +# CONFIG_USB_GADGET_AMD5536UDC is not set +# CONFIG_USB_GADGET_FSL_QE is not set +# CONFIG_USB_GADGET_CI13XXX is not set +# CONFIG_USB_GADGET_NET2280 is not set +# CONFIG_USB_GADGET_GOKU is not set +# CONFIG_USB_GADGET_LANGWELL is not set +# CONFIG_USB_GADGET_DUMMY_HCD is not set +CONFIG_USB_GADGET_DUALSPEED=y +CONFIG_USB_ZERO=y +# CONFIG_USB_ZERO_HNPTEST is not set +# CONFIG_USB_AUDIO is not set +# CONFIG_USB_ETH is not set +# CONFIG_USB_GADGETFS is not set +# CONFIG_USB_FILE_STORAGE is not set +# CONFIG_USB_G_SERIAL is not set +# CONFIG_USB_MIDI_GADGET is not set +# CONFIG_USB_G_PRINTER is not set +# CONFIG_USB_CDC_COMPOSITE is not set + +# +# OTG and related infrastructure +# +CONFIG_USB_OTG_UTILS=y +# CONFIG_USB_GPIO_VBUS is not set +# CONFIG_ISP1301_OMAP is not set +CONFIG_TWL4030_USB=y +# CONFIG_NOP_USB_XCEIV is not set +CONFIG_MMC=y +# CONFIG_MMC_DEBUG is not set +# CONFIG_MMC_UNSAFE_RESUME is not set + +# +# MMC/SD/SDIO Card Drivers +# +CONFIG_MMC_BLOCK=y +CONFIG_MMC_BLOCK_BOUNCE=y +# CONFIG_SDIO_UART is not set +# CONFIG_MMC_TEST is not set + +# +# MMC/SD/SDIO Host Controller Drivers +# +# CONFIG_MMC_SDHCI is not set +# CONFIG_MMC_OMAP is not set +CONFIG_MMC_OMAP_HS=y +# CONFIG_MMC_AT91 is not set +# CONFIG_MMC_ATMELMCI is not set +# CONFIG_MMC_SPI is not set +# CONFIG_MEMSTICK is not set +# CONFIG_NEW_LEDS is not set +# CONFIG_ACCESSIBILITY is not set +CONFIG_RTC_LIB=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_HCTOSYS=y +CONFIG_RTC_HCTOSYS_DEVICE="rtc0" +# CONFIG_RTC_DEBUG is not set + +# +# RTC interfaces +# +CONFIG_RTC_INTF_SYSFS=y +CONFIG_RTC_INTF_PROC=y +CONFIG_RTC_INTF_DEV=y +# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set +# CONFIG_RTC_DRV_TEST is not set + +# +# I2C RTC drivers +# +# CONFIG_RTC_DRV_DS1307 is not set +# CONFIG_RTC_DRV_DS1374 is not set +# CONFIG_RTC_DRV_DS1672 is not set +# CONFIG_RTC_DRV_MAX6900 is not set +# CONFIG_RTC_DRV_RS5C372 is not set +# CONFIG_RTC_DRV_ISL1208 is not set +# CONFIG_RTC_DRV_X1205 is not set +# CONFIG_RTC_DRV_PCF8563 is not set +# CONFIG_RTC_DRV_PCF8583 is not set +# CONFIG_RTC_DRV_M41T80 is not set +# CONFIG_RTC_DRV_TWL4030 is not set +# CONFIG_RTC_DRV_S35390A is not set +# CONFIG_RTC_DRV_FM3130 is not set +# CONFIG_RTC_DRV_RX8581 is not set +# CONFIG_RTC_DRV_RX8025 is not set + +# +# SPI RTC drivers +# +# CONFIG_RTC_DRV_M41T94 is not set +# CONFIG_RTC_DRV_DS1305 is not set +# CONFIG_RTC_DRV_DS1390 is not set +# CONFIG_RTC_DRV_MAX6902 is not set +# CONFIG_RTC_DRV_R9701 is not set +# CONFIG_RTC_DRV_RS5C348 is not set +# CONFIG_RTC_DRV_DS3234 is not set +# CONFIG_RTC_DRV_PCF2123 is not set + +# +# Platform RTC drivers +# +# CONFIG_RTC_DRV_CMOS is not set +# CONFIG_RTC_DRV_DS1286 is not set +# CONFIG_RTC_DRV_DS1511 is not set +# CONFIG_RTC_DRV_DS1553 is not set +# CONFIG_RTC_DRV_DS1742 is not set +# CONFIG_RTC_DRV_STK17TA8 is not set +# CONFIG_RTC_DRV_M48T86 is not set +# CONFIG_RTC_DRV_M48T35 is not set +# CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_BQ4802 is not set +# CONFIG_RTC_DRV_V3020 is not set + +# +# on-CPU RTC drivers +# +# CONFIG_DMADEVICES is not set +# CONFIG_AUXDISPLAY is not set +# CONFIG_UIO is not set + +# +# TI VLYNQ +# +# CONFIG_STAGING is not set + +# +# CBUS support +# +# CONFIG_CBUS is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +CONFIG_EXT3_FS=y +# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set +# CONFIG_EXT3_FS_XATTR is not set +# CONFIG_EXT4_FS is not set +CONFIG_JBD=y +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +CONFIG_FS_POSIX_ACL=y +# CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set +# CONFIG_OCFS2_FS is not set +# CONFIG_BTRFS_FS is not set +# CONFIG_NILFS2_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y +CONFIG_DNOTIFY=y +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +CONFIG_QUOTA=y +# CONFIG_QUOTA_NETLINK_INTERFACE is not set +CONFIG_PRINT_QUOTA_WARNING=y +CONFIG_QUOTA_TREE=y +# CONFIG_QFMT_V1 is not set +CONFIG_QFMT_V2=y +CONFIG_QUOTACTL=y +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# Caches +# +# CONFIG_FSCACHE is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +CONFIG_FAT_FS=y +CONFIG_MSDOS_FS=y +CONFIG_VFAT_FS=y +CONFIG_FAT_DEFAULT_CODEPAGE=437 +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +# CONFIG_CONFIGFS_FS is not set +CONFIG_MISC_FILESYSTEMS=y +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +# CONFIG_CRAMFS is not set +# CONFIG_SQUASHFS is not set +# CONFIG_VXFS_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_OMFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_ROMFS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set +CONFIG_NETWORK_FILESYSTEMS=y +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +CONFIG_NFS_V3_ACL=y +CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set +CONFIG_ROOT_NFS=y +# CONFIG_NFSD is not set +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_NFS_ACL_SUPPORT=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +CONFIG_SUNRPC_GSS=y +CONFIG_RPCSEC_GSS_KRB5=y +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set + +# +# Partition Types +# +CONFIG_PARTITION_ADVANCED=y +# CONFIG_ACORN_PARTITION is not set +# CONFIG_OSF_PARTITION is not set +# CONFIG_AMIGA_PARTITION is not set +# CONFIG_ATARI_PARTITION is not set +# CONFIG_MAC_PARTITION is not set +CONFIG_MSDOS_PARTITION=y +# CONFIG_BSD_DISKLABEL is not set +# CONFIG_MINIX_SUBPARTITION is not set +# CONFIG_SOLARIS_X86_PARTITION is not set +# CONFIG_UNIXWARE_DISKLABEL is not set +# CONFIG_LDM_PARTITION is not set +# CONFIG_SGI_PARTITION is not set +# CONFIG_ULTRIX_PARTITION is not set +# CONFIG_SUN_PARTITION is not set +# CONFIG_KARMA_PARTITION is not set +# CONFIG_EFI_PARTITION is not set +# CONFIG_SYSV68_PARTITION is not set +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +CONFIG_NLS_CODEPAGE_437=y +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +# CONFIG_NLS_CODEPAGE_850 is not set +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +CONFIG_NLS_ISO8859_1=y +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +# CONFIG_NLS_UTF8 is not set +# CONFIG_DLM is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y +CONFIG_ENABLE_MUST_CHECK=y +CONFIG_FRAME_WARN=1024 +CONFIG_MAGIC_SYSRQ=y +# CONFIG_STRIP_ASM_SYMS is not set +# CONFIG_UNUSED_SYMBOLS is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_HEADERS_CHECK is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_DEBUG_SHIRQ is not set +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set +CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 +CONFIG_DETECT_HUNG_TASK=y +# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set +CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0 +CONFIG_SCHED_DEBUG=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_OBJECTS is not set +# CONFIG_DEBUG_SLAB is not set +# CONFIG_DEBUG_KMEMLEAK is not set +# CONFIG_DEBUG_RT_MUTEXES is not set +# CONFIG_RT_MUTEX_TESTER is not set +# CONFIG_DEBUG_SPINLOCK is not set +CONFIG_DEBUG_MUTEXES=y +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set +# CONFIG_DEBUG_KOBJECT is not set +# CONFIG_DEBUG_BUGVERBOSE is not set +CONFIG_DEBUG_INFO=y +# CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_WRITECOUNT is not set +# CONFIG_DEBUG_MEMORY_INIT is not set +# CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set +# CONFIG_DEBUG_NOTIFIERS is not set +# CONFIG_DEBUG_CREDENTIALS is not set +# CONFIG_BOOT_PRINTK_DELAY is not set +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_RCU_CPU_STALL_DETECTOR is not set +# CONFIG_BACKTRACE_SELF_TEST is not set +# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set +# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set +# CONFIG_FAULT_INJECTION is not set +# CONFIG_LATENCYTOP is not set +# CONFIG_PAGE_POISONING is not set +CONFIG_HAVE_FUNCTION_TRACER=y +CONFIG_TRACING_SUPPORT=y +CONFIG_FTRACE=y +# CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set +# CONFIG_SCHED_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set +# CONFIG_BOOT_TRACER is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set +# CONFIG_STACK_TRACER is not set +# CONFIG_KMEMTRACE is not set +# CONFIG_WORKQUEUE_TRACER is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_SAMPLES is not set +CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_KGDB is not set +CONFIG_ARM_UNWIND=y +# CONFIG_DEBUG_USER is not set +# CONFIG_DEBUG_ERRORS is not set +# CONFIG_DEBUG_STACK_USAGE is not set +CONFIG_DEBUG_LL=y +# CONFIG_DEBUG_ICEDCC is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set +CONFIG_CRYPTO=y + +# +# Crypto core or helper +# +CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_ALGAPI2=y +CONFIG_CRYPTO_AEAD2=y +CONFIG_CRYPTO_BLKCIPHER=y +CONFIG_CRYPTO_BLKCIPHER2=y +CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_HASH2=y +CONFIG_CRYPTO_RNG2=y +CONFIG_CRYPTO_PCOMP=y +CONFIG_CRYPTO_MANAGER=y +CONFIG_CRYPTO_MANAGER2=y +# CONFIG_CRYPTO_GF128MUL is not set +# CONFIG_CRYPTO_NULL is not set +CONFIG_CRYPTO_WORKQUEUE=y +# CONFIG_CRYPTO_CRYPTD is not set +# CONFIG_CRYPTO_AUTHENC is not set +# CONFIG_CRYPTO_TEST is not set + +# +# Authenticated Encryption with Associated Data +# +# CONFIG_CRYPTO_CCM is not set +# CONFIG_CRYPTO_GCM is not set +# CONFIG_CRYPTO_SEQIV is not set + +# +# Block modes +# +CONFIG_CRYPTO_CBC=y +# CONFIG_CRYPTO_CTR is not set +# CONFIG_CRYPTO_CTS is not set +CONFIG_CRYPTO_ECB=m +# CONFIG_CRYPTO_LRW is not set +CONFIG_CRYPTO_PCBC=m +# CONFIG_CRYPTO_XTS is not set + +# +# Hash modes +# +# CONFIG_CRYPTO_HMAC is not set +# CONFIG_CRYPTO_XCBC is not set +# CONFIG_CRYPTO_VMAC is not set + +# +# Digest +# +CONFIG_CRYPTO_CRC32C=y +# CONFIG_CRYPTO_GHASH is not set +# CONFIG_CRYPTO_MD4 is not set +CONFIG_CRYPTO_MD5=y +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_RMD128 is not set +# CONFIG_CRYPTO_RMD160 is not set +# CONFIG_CRYPTO_RMD256 is not set +# CONFIG_CRYPTO_RMD320 is not set +# CONFIG_CRYPTO_SHA1 is not set +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_TGR192 is not set +# CONFIG_CRYPTO_WP512 is not set + +# +# Ciphers +# +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +CONFIG_CRYPTO_DES=y +# CONFIG_CRYPTO_FCRYPT is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_SALSA20 is not set +# CONFIG_CRYPTO_SEED is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_TWOFISH is not set + +# +# Compression +# +# CONFIG_CRYPTO_DEFLATE is not set +# CONFIG_CRYPTO_ZLIB is not set +# CONFIG_CRYPTO_LZO is not set + +# +# Random Number Generation +# +# CONFIG_CRYPTO_ANSI_CPRNG is not set +CONFIG_CRYPTO_HW=y +# CONFIG_BINARY_PRINTF is not set + +# +# Library routines +# +CONFIG_BITREVERSE=y +CONFIG_GENERIC_FIND_LAST_BIT=y +CONFIG_CRC_CCITT=y +# CONFIG_CRC16 is not set +CONFIG_CRC_T10DIF=y +# CONFIG_CRC_ITU_T is not set +CONFIG_CRC32=y +# CONFIG_CRC7 is not set +CONFIG_LIBCRC32C=y +CONFIG_ZLIB_INFLATE=y +CONFIG_DECOMPRESS_GZIP=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y +CONFIG_NLATTR=y -- 1.6.5.1.69.g36942 ^ permalink raw reply related [flat|nested] 16+ messages in thread
* Re: [PATCH 7/8] omap: 3630sdp: introduce 3630 sdp board support 2009-11-03 21:20 ` [PATCH 7/8] omap: 3630sdp: introduce 3630 sdp board support Vikram Pandita 2009-11-03 21:20 ` [PATCH 8/8] omap: 3630sdp: defconfig creation Vikram Pandita @ 2009-11-03 22:31 ` Nishanth Menon 1 sibling, 0 replies; 16+ messages in thread From: Nishanth Menon @ 2009-11-03 22:31 UTC (permalink / raw) To: Vikram Pandita; +Cc: linux-omap@vger.kernel.org Vikram Pandita had written, on 11/03/2009 03:20 PM, the following: > Add 3630SDP board support > > The board shares the same peripherals as a zoom2 main. > So reuse the peripheral file of zoom platform. > > The RAM part is Hynix memory as as in zoom3. would be great to add more details on this. > > Signed-off-by: Vikram Pandita <vikram.pandita@ti.com> > --- > arch/arm/mach-omap2/Kconfig | 4 ++ > arch/arm/mach-omap2/Makefile | 3 + > arch/arm/mach-omap2/board-3630sdp.c | 96 +++++++++++++++++++++++++++++++++++ > 3 files changed, 103 insertions(+), 0 deletions(-) > create mode 100755 arch/arm/mach-omap2/board-3630sdp.c > > diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig > index 9824775..83551a8 100644 > --- a/arch/arm/mach-omap2/Kconfig > +++ b/arch/arm/mach-omap2/Kconfig > @@ -105,6 +105,10 @@ config MACH_OMAP_ZOOM3 > bool "OMAP3630 Zoom3 board" > depends on ARCH_OMAP3 && ARCH_OMAP34XX > > +config MACH_OMAP_3630SDP > + bool "OMAP3630 SDP board" > + depends on ARCH_OMAP3 && ARCH_OMAP34XX > + > config MACH_OMAP_4430SDP > bool "OMAP 4430 SDP board" > depends on ARCH_OMAP4 > diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile > index 712e7fc..90cf2cc 100644 > --- a/arch/arm/mach-omap2/Makefile > +++ b/arch/arm/mach-omap2/Makefile > @@ -79,6 +79,9 @@ obj-$(CONFIG_MACH_OMAP_ZOOM3) += board-zoom3.o \ > board-zoom-peripherals.o \ > mmc-twl4030.o \ > board-zoom-debugboard.o > +obj-$(CONFIG_MACH_OMAP_3630SDP) += board-3630sdp.o \ > + board-zoom-peripherals.o \ > + mmc-twl4030.o > obj-$(CONFIG_MACH_CM_T35) += board-cm-t35.o \ > mmc-twl4030.o > > diff --git a/arch/arm/mach-omap2/board-3630sdp.c b/arch/arm/mach-omap2/board-3630sdp.c > new file mode 100755 > index 0000000..450fcdd > --- /dev/null > +++ b/arch/arm/mach-omap2/board-3630sdp.c > @@ -0,0 +1,96 @@ > +/* > + * Copyright (C) 2009 Texas Instruments Inc. > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + */ > + > +#include <linux/kernel.h> > +#include <linux/init.h> > +#include <linux/platform_device.h> > +#include <linux/input.h> > +#include <linux/gpio.h> > + > +#include <asm/mach-types.h> > +#include <asm/mach/arch.h> > + > +#include <plat/common.h> > +#include <plat/board.h> > +#include <plat/gpmc-smc91x.h> > +#include <plat/mux.h> > +#include <plat/usb.h> > + > +#include "sdram-hynix-h8mbx00u0mer-0em.h" > + > +#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) > +static struct omap_smc91x_platform_data board_smc91x_data = { > + .cs = 3, > + .flags = GPMC_MUX_ADD_DATA | IORESOURCE_IRQ_LOWLEVEL, > +}; > + > +static void __init board_smc91x_init(void) > +{ > + board_smc91x_data.gpio_irq = 158; > + gpmc_smc91x_init(&board_smc91x_data); > +} > +#else > +static inline void board_smc91x_init(void) > +{ > +} > +#endif > + > +static void enable_board_wakeup_source(void) > +{ > + omap_cfg_reg(AF26_34XX_SYS_NIRQ); /* T2 interrupt line (keypad) */ > +} > + > +static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = { > + > + .port_mode[0] = EHCI_HCD_OMAP_MODE_PHY, > + .port_mode[1] = EHCI_HCD_OMAP_MODE_PHY, > + .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN, > + > + .phy_reset = true, > + .reset_gpio_port[0] = 126, > + .reset_gpio_port[1] = 61, > + .reset_gpio_port[2] = -EINVAL > +}; > + > +static void __init omap_sdp_map_io(void) > +{ > + omap2_set_globals_343x(); > + omap2_map_common_io(); > +} > + > +static struct omap_board_config_kernel sdp_config[] __initdata = { > +}; EOL? > +static void __init omap_sdp_init_irq(void) > +{ > + omap_board_config = sdp_config; > + omap_board_config_size = ARRAY_SIZE(sdp_config); > + omap2_init_common_hw(h8mbx00u0mer0em_sdrc_params, > + h8mbx00u0mer0em_sdrc_params); > + omap_init_irq(); > + omap_gpio_init(); > +} > + > +extern void __init zoom_peripherals_init(void); > + > +static void __init omap_sdp_init(void) > +{ > + zoom_peripherals_init(); > + board_smc91x_init(); > + enable_board_wakeup_source(); > + usb_ehci_init(&ehci_pdata); > +} > + > +MACHINE_START(OMAP_3630SDP, "OMAP 3630SDP board") > + .phys_io = 0x48000000, > + .io_pg_offst = ((0xfa000000) >> 18) & 0xfffc, > + .boot_params = 0x80000100, > + .map_io = omap_sdp_map_io, > + .init_irq = omap_sdp_init_irq, > + .init_machine = omap_sdp_init, > + .timer = &omap_timer, > +MACHINE_END nice and simple :).. thanks.. -- Regards, Nishanth Menon ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH 5/8] omap: zoom3: introduce zoom3 board support 2009-11-03 21:20 ` [PATCH 5/8] omap: zoom3: introduce zoom3 board support Vikram Pandita 2009-11-03 21:20 ` [PATCH 6/8] omap: zoom3: defconfig creation Vikram Pandita @ 2009-11-03 22:28 ` Nishanth Menon 1 sibling, 0 replies; 16+ messages in thread From: Nishanth Menon @ 2009-11-03 22:28 UTC (permalink / raw) To: Pandita, Vikram; +Cc: linux-omap@vger.kernel.org, Vikram Pandita Pandita, Vikram had written, on 11/03/2009 03:20 PM, the following: > Zoom3 is the next versoin of Zoom2 board. > There has been a silicon update from zoom2 to zoom3. > Zoom2 has OMAP34xx > Zoom3 has OMAP3630 > Zoom3 = OMAP3630 SOM board + same zoom2 main board + same debugboard > > Zoom3 has a different SDRAM part from Hynix > Zoom2 had SDRAM part from micron > would have been great to get more details on zoom3. > Reuse the zoom2 files as much for zoom3, as at board level, > there is no change at all. > > Signed-off-by: Vikram Pandita <vikram.pandtia@ti.com> > --- > arch/arm/mach-omap2/Kconfig | 4 + > arch/arm/mach-omap2/Makefile | 4 + > arch/arm/mach-omap2/board-zoom3.c | 59 ++++++++++++++++++++ > arch/arm/mach-omap2/sdram-hynix-h8mbx00u0mer-0em.h | 54 ++++++++++++++++++ > 4 files changed, 121 insertions(+), 0 deletions(-) > create mode 100755 arch/arm/mach-omap2/board-zoom3.c > create mode 100644 arch/arm/mach-omap2/sdram-hynix-h8mbx00u0mer-0em.h > > diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig > index 8685df5..9824775 100644 > --- a/arch/arm/mach-omap2/Kconfig > +++ b/arch/arm/mach-omap2/Kconfig > @@ -101,6 +101,10 @@ config MACH_CM_T35 > bool "CompuLab CM-T35 module" > depends on ARCH_OMAP3 && ARCH_OMAP34XX > > +config MACH_OMAP_ZOOM3 > + bool "OMAP3630 Zoom3 board" > + depends on ARCH_OMAP3 && ARCH_OMAP34XX > + > config MACH_OMAP_4430SDP > bool "OMAP 4430 SDP board" > depends on ARCH_OMAP4 > diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile > index 4d66b42..712e7fc 100644 > --- a/arch/arm/mach-omap2/Makefile > +++ b/arch/arm/mach-omap2/Makefile > @@ -75,6 +75,10 @@ obj-$(CONFIG_MACH_OMAP_ZOOM2) += board-zoom2.o \ > board-zoom-peripherals.o \ > mmc-twl4030.o \ > board-zoom-debugboard.o > +obj-$(CONFIG_MACH_OMAP_ZOOM3) += board-zoom3.o \ > + board-zoom-peripherals.o \ > + mmc-twl4030.o \ > + board-zoom-debugboard.o > obj-$(CONFIG_MACH_CM_T35) += board-cm-t35.o \ > mmc-twl4030.o > > diff --git a/arch/arm/mach-omap2/board-zoom3.c b/arch/arm/mach-omap2/board-zoom3.c > new file mode 100755 > index 0000000..aebe7b8 > --- /dev/null > +++ b/arch/arm/mach-omap2/board-zoom3.c > @@ -0,0 +1,59 @@ > +/* > + * Copyright (C) 2009 Texas Instruments Inc. > + * > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + */ > + > +#include <linux/kernel.h> > +#include <linux/init.h> > +#include <linux/platform_device.h> > +#include <linux/input.h> > +#include <linux/gpio.h> > + > +#include <asm/mach-types.h> > +#include <asm/mach/arch.h> > + > +#include <plat/common.h> > +#include <plat/board.h> > + > +#include "sdram-hynix-h8mbx00u0mer-0em.h" > + > +static void __init omap_zoom_map_io(void) > +{ > + omap2_set_globals_343x(); > + omap2_map_common_io(); > +} > + > +static struct omap_board_config_kernel zoom_config[] __initdata = { > +}; EOL? > +static void __init omap_zoom_init_irq(void) > +{ > + omap_board_config = zoom_config; > + omap_board_config_size = ARRAY_SIZE(zoom_config); > + omap2_init_common_hw(h8mbx00u0mer0em_sdrc_params, > + h8mbx00u0mer0em_sdrc_params); > + omap_init_irq(); > + omap_gpio_init(); > +} > + > +extern int __init omap_zoom2_debugboard_init(void); > +extern void __init zoom_peripherals_init(void); > + > +static void __init omap_zoom_init(void) > +{ > + zoom_peripherals_init(); ^^^^^^^^ <- is that spaces here? could you checkpatch please? > + omap_zoom2_debugboard_init(); > +} > + > +MACHINE_START(OMAP_ZOOM3, "OMAP Zoom3 board") > + .phys_io = 0x48000000, > + .io_pg_offst = ((0xfa000000) >> 18) & 0xfffc, > + .boot_params = 0x80000100, > + .map_io = omap_zoom_map_io, > + .init_irq = omap_zoom_init_irq, > + .init_machine = omap_zoom_init, > + .timer = &omap_timer, > +MACHINE_END love a small board file such as this.. thanks.. > diff --git a/arch/arm/mach-omap2/sdram-hynix-h8mbx00u0mer-0em.h b/arch/arm/mach-omap2/sdram-hynix-h8mbx00u0mer-0em.h > new file mode 100644 > index 0000000..c469c48 > --- /dev/null > +++ b/arch/arm/mach-omap2/sdram-hynix-h8mbx00u0mer-0em.h > @@ -0,0 +1,54 @@ > +/* > + * SDRC register values for the Hynix H8MBX00U0MER-0EM > + * > + * Copyright (C) 2008-2009 Texas Instruments, Inc. > + * Copyright (C) 2008-2009 Nokia Corporation > + * > + * Nicole Chalhoub / Vincent Bour > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + */ > + > +#ifndef ARCH_ARM_MACH_OMAP2_SDRAM_HYNIX_H8MBX00U0MER0EM ^^^ maybe a prefix of __? -- Regards, Nishanth Menon ^ permalink raw reply [flat|nested] 16+ messages in thread
* RE: [PATCH 4/8] omap: zoom2: update defconfig 2009-11-03 21:20 ` [PATCH 4/8] omap: zoom2: update defconfig Vikram Pandita 2009-11-03 21:20 ` [PATCH 5/8] omap: zoom3: introduce zoom3 board support Vikram Pandita @ 2009-11-04 7:09 ` G, Manjunath Kondaiah 1 sibling, 0 replies; 16+ messages in thread From: G, Manjunath Kondaiah @ 2009-11-04 7:09 UTC (permalink / raw) To: Pandita, Vikram, linux-omap@vger.kernel.org > diff --git a/arch/arm/configs/omap_zoom2_defconfig > b/arch/arm/configs/omap_zoom2_defconfig > index f1739fa..db4fc1c 100644 > --- a/arch/arm/configs/omap_zoom2_defconfig > +++ b/arch/arm/configs/omap_zoom2_defconfig > @@ -1,15 +1,13 @@ > # > # Automatically generated make config: don't edit > -# Linux kernel version: 2.6.30-omap1 > -# Fri Jun 12 17:25:46 2009 > +# Linux kernel version: 2.6.32-rc5 > +# Tue Nov 3 12:00:13 2009 > # > +# CONFIG_PHONE is not set <...snip...> > > # > # Input device support Why not enable CONFIG_KEYBOARD_TWL4030? > @@ -619,21 +639,22 @@ CONFIG_TOUCHSCREEN_ADS7846=y > # CONFIG_TOUCHSCREEN_AD7879_I2C is not set > # CONFIG_TOUCHSCREEN_AD7879_SPI is not set > # CONFIG_TOUCHSCREEN_AD7879 is not set > +# CONFIG_TOUCHSCREEN_EETI is not set > # CONFIG_TOUCHSCREEN_FUJITSU is not set <...snip...> > # CONFIG_NEW_LEDS is not set > +# CONFIG_ACCESSIBILITY is not set > CONFIG_RTC_LIB=y > CONFIG_RTC_CLASS=y > CONFIG_RTC_HCTOSYS=y > @@ -1128,6 +1173,7 @@ CONFIG_RTC_INTF_DEV=y > # CONFIG_RTC_DRV_S35390A is not set > # CONFIG_RTC_DRV_FM3130 is not set > # CONFIG_RTC_DRV_RX8581 is not set > +# CONFIG_RTC_DRV_RX8025 is not set > And here - CONFIG_RTC_DRV_TWL4030 -Manjunath ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH 3/8] omap: zoom2: split baord file for reuse 2009-11-03 21:20 ` [PATCH 3/8] omap: zoom2: split baord file for reuse Vikram Pandita 2009-11-03 21:20 ` [PATCH 4/8] omap: zoom2: update defconfig Vikram Pandita @ 2009-11-03 22:17 ` Nishanth Menon 1 sibling, 0 replies; 16+ messages in thread From: Nishanth Menon @ 2009-11-03 22:17 UTC (permalink / raw) To: Pandita, Vikram; +Cc: linux-omap@vger.kernel.org, Vikram Pandita Pandita, Vikram had written, on 11/03/2009 03:20 PM, the following: Please fix subject typo: [PATCH 3/8] omap: zoom2: split baord file for reuse ^^^^ board [...] > diff --git a/arch/arm/mach-omap2/board-zoom-peripherals.c b/arch/arm/mach-omap2/board-zoom-peripherals.c > new file mode 100755 > index 0000000..c799eca > --- /dev/null > +++ b/arch/arm/mach-omap2/board-zoom-peripherals.c generic -> zoom Vs LDP.. Vs Zoom2 Vs Zoom3 naming conventions.. are we saying we dont care about LDP anymore? all zooms are zoom2 or zoom3? [...] > + > +//static struct twl4030_gpio_platform_data zoom_gpio_data = { > +// .gpio_base = OMAP_MAX_GPIO_LINES, > +// .irq_base = TWL4030_GPIO_IRQ_BASE, > +// .irq_end = TWL4030_GPIO_IRQ_END, > +// .pulldowns = BIT(0) | BIT(1) | BIT(2) | BIT(3) > +// | BIT(4) | BIT(5) > +// | BIT(8) | BIT(9) | BIT(10) | BIT(11) > +// | BIT(12) | BIT(13) | BIT(14) | BIT(15) > +// | BIT(16) | BIT(17) , > +// .setup = zoom_twlgpio_setup, > +//}; NAK to // > +static struct twl4030_gpio_platform_data zoom_gpio_data = { > + .gpio_base = OMAP_MAX_GPIO_LINES, > + .irq_base = TWL4030_GPIO_IRQ_BASE, > + .irq_end = TWL4030_GPIO_IRQ_END, > + .setup = zoom_twl_gpio_setup, > +}; > + > +static struct twl4030_usb_data zoom_usb_data = { > + .usb_mode = T2_USB_MODE_ULPI, > +}; > + > +/* TODO: enable T2 scripts */ > +#if 0 NAK to #if 0 - introduce seperately if not operational. [...] > diff --git a/arch/arm/mach-omap2/board-zoom2.c b/arch/arm/mach-omap2/board-zoom2.c > old mode 100644 > new mode 100755 > index 4ad9b94..abcc1ae > --- a/arch/arm/mach-omap2/board-zoom2.c > +++ b/arch/arm/mach-omap2/board-zoom2.c > @@ -1,8 +1,6 @@ > /* > * Copyright (C) 2009 Texas Instruments Inc. > - * Mikkel Christensen <mlc@ti.com> > * > - * Modified from mach-omap2/board-ldp.c [Should we loose the history?] [...] > -static void __init omap_zoom2_init_irq(void) > +static void __init omap_zoom_init_irq(void) Question on naming.. as raised above. [...] -- Regards, Nishanth Menon ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH 2/8] omap: DEBUG_LL: allow no omap uart configuration 2009-11-03 21:20 ` [PATCH 2/8] omap: DEBUG_LL: allow no omap uart configuration Vikram Pandita 2009-11-03 21:20 ` [PATCH 3/8] omap: zoom2: split baord file for reuse Vikram Pandita @ 2009-11-03 22:09 ` Nishanth Menon 1 sibling, 0 replies; 16+ messages in thread From: Nishanth Menon @ 2009-11-03 22:09 UTC (permalink / raw) To: Vikram Pandita; +Cc: linux-omap@vger.kernel.org Vikram Pandita had written, on 11/03/2009 03:20 PM, the following: [...] > diff --git a/arch/arm/plat-omap/include/plat/uncompress.h b/arch/arm/plat-omap/include/plat/uncompress.h > index e22f575..49b38f0 100644 > --- a/arch/arm/plat-omap/include/plat/uncompress.h > +++ b/arch/arm/plat-omap/include/plat/uncompress.h > @@ -44,8 +44,10 @@ static void putc(int c) > uart = (volatile u8 *)(OMAP_UART3_BASE); > #elif defined(CONFIG_OMAP_LL_DEBUG_UART2) > uart = (volatile u8 *)(OMAP_UART2_BASE); > -#else > +#elif defined(CONFIG_OMAP_LL_DEBUG_UART1) > uart = (volatile u8 *)(OMAP_UART1_BASE); > +#elif defined(CONFIG_OMAP_LL_DEBUG_NONE) > + return; what is the default? an #else missing? maybe, we might want to use: #else return; also I am not clear about #ifdef CONFIG_MACH_OMAP_PALMTE return #endif Vs this -> should'nt PALMTE also use this instead? unrelated.. purpose of #ifdef CONFIG_ARCH_OMAP in arch/arm/plat-omap/include/plat/uncompress.h is'nt it already OMAP? -- Regards, Nishanth Menon ^ permalink raw reply [flat|nested] 16+ messages in thread
* RE: [PATCH 0/8] RFC: introduce 3630 boards 2009-11-03 21:20 [PATCH 0/8] RFC: introduce 3630 boards Vikram Pandita 2009-11-03 21:20 ` [PATCH 1/8] omap: 3630: update is_chip variable Vikram Pandita @ 2009-11-03 21:23 ` Pandita, Vikram 2009-11-03 21:26 ` Pandita, Vikram 1 sibling, 1 reply; 16+ messages in thread From: Pandita, Vikram @ 2009-11-03 21:23 UTC (permalink / raw) To: linux-omap@vger.kernel.org >-----Original Message----- >From: Pandita, Vikram >Sent: Tuesday, November 03, 2009 3:20 PM >To: linux-omap@vger.kernel.org >Cc: Pandita, Vikram >Subject: [PATCH 0/8] RFC: introduce 3630 boards > >Introducing 3630 boards: zoom3 and sdp3630 These patches are in my git tree at: git://dev.omapzoom.org/pub/scm/integration/kernel-omap3.git zoom3 this is to help ease cloning in case required. > >The peripherals are very similar for the two bards as per this discussion: >http://marc.info/?l=linux-omap&m=125676595710748&w=2 > >So maximum reuse is done for the board files for zoom3 and sdp3630 > >Review comments incorporated: >http://marc.info/?l=linux-omap&m=125632676504364&w=2 >http://marc.info/?l=linux-omap&m=125632720804869&w=2 >http://marc.info/?l=linux-omap&m=125633994320138&w=2 > >Vikram Pandita (8): > omap: 3630: update is_chip variable > omap: DEBUG_LL: allow no omap uart configuration > omap: zoom2: split baord file for reuse > omap: zoom2: update defconfig > omap: zoom3: introduce zoom3 board support > omap: zoom3: defconfig creation > omap: 3630sdp: introduce 3630 sdp board support > omap: 3630sdp: defconfig creation > > arch/arm/configs/omap_3630sdp_defconfig | 1606 ++++++++++++++++++++ > arch/arm/configs/omap_zoom2_defconfig | 231 ++-- > arch/arm/configs/omap_zoom3_defconfig | 1605 +++++++++++++++++++ > arch/arm/mach-omap2/Kconfig | 8 + > arch/arm/mach-omap2/Makefile | 8 + > arch/arm/mach-omap2/board-3630sdp.c | 96 ++ > arch/arm/mach-omap2/board-zoom-peripherals.c | 414 +++++ > arch/arm/mach-omap2/board-zoom2.c | 261 +--- > arch/arm/mach-omap2/board-zoom3.c | 59 + > arch/arm/mach-omap2/id.c | 2 + > arch/arm/mach-omap2/sdram-hynix-h8mbx00u0mer-0em.h | 54 + > arch/arm/plat-omap/Kconfig | 3 + > arch/arm/plat-omap/include/plat/cpu.h | 7 +- > arch/arm/plat-omap/include/plat/uncompress.h | 4 +- > 14 files changed, 4018 insertions(+), 340 deletions(-) > create mode 100644 arch/arm/configs/omap_3630sdp_defconfig > create mode 100644 arch/arm/configs/omap_zoom3_defconfig > create mode 100755 arch/arm/mach-omap2/board-3630sdp.c > create mode 100755 arch/arm/mach-omap2/board-zoom-peripherals.c > mode change 100644 => 100755 arch/arm/mach-omap2/board-zoom2.c > create mode 100755 arch/arm/mach-omap2/board-zoom3.c > create mode 100644 arch/arm/mach-omap2/sdram-hynix-h8mbx00u0mer-0em.h ^ permalink raw reply [flat|nested] 16+ messages in thread
* RE: [PATCH 0/8] RFC: introduce 3630 boards 2009-11-03 21:23 ` [PATCH 0/8] RFC: introduce 3630 boards Pandita, Vikram @ 2009-11-03 21:26 ` Pandita, Vikram 0 siblings, 0 replies; 16+ messages in thread From: Pandita, Vikram @ 2009-11-03 21:26 UTC (permalink / raw) To: linux-omap@vger.kernel.org >-----Original Message----- >From: linux-omap-owner@vger.kernel.org [mailto:linux-omap-owner@vger.kernel.org] On Behalf Of >>Subject: [PATCH 0/8] RFC: introduce 3630 boards >> >>Introducing 3630 boards: zoom3 and sdp3630 > >These patches are in my git tree at: >git://dev.omapzoom.org/pub/scm/integration/kernel-omap3.git zoom3 Sorry for the wrong tree. This is the right one: git://dev.omapzoom.org/pub/scm/vikram/omap3.git zoom3 > >this is to help ease cloning in case required. > >> >>The peripherals are very similar for the two bards as per this discussion: >>http://marc.info/?l=linux-omap&m=125676595710748&w=2 >> >>So maximum reuse is done for the board files for zoom3 and sdp3630 >> >>Review comments incorporated: >>http://marc.info/?l=linux-omap&m=125632676504364&w=2 >>http://marc.info/?l=linux-omap&m=125632720804869&w=2 >>http://marc.info/?l=linux-omap&m=125633994320138&w=2 >> >>Vikram Pandita (8): >> omap: 3630: update is_chip variable >> omap: DEBUG_LL: allow no omap uart configuration >> omap: zoom2: split baord file for reuse >> omap: zoom2: update defconfig >> omap: zoom3: introduce zoom3 board support >> omap: zoom3: defconfig creation >> omap: 3630sdp: introduce 3630 sdp board support >> omap: 3630sdp: defconfig creation >> >> arch/arm/configs/omap_3630sdp_defconfig | 1606 ++++++++++++++++++++ >> arch/arm/configs/omap_zoom2_defconfig | 231 ++-- >> arch/arm/configs/omap_zoom3_defconfig | 1605 +++++++++++++++++++ >> arch/arm/mach-omap2/Kconfig | 8 + >> arch/arm/mach-omap2/Makefile | 8 + >> arch/arm/mach-omap2/board-3630sdp.c | 96 ++ >> arch/arm/mach-omap2/board-zoom-peripherals.c | 414 +++++ >> arch/arm/mach-omap2/board-zoom2.c | 261 +--- >> arch/arm/mach-omap2/board-zoom3.c | 59 + >> arch/arm/mach-omap2/id.c | 2 + >> arch/arm/mach-omap2/sdram-hynix-h8mbx00u0mer-0em.h | 54 + >> arch/arm/plat-omap/Kconfig | 3 + >> arch/arm/plat-omap/include/plat/cpu.h | 7 +- >> arch/arm/plat-omap/include/plat/uncompress.h | 4 +- >> 14 files changed, 4018 insertions(+), 340 deletions(-) >> create mode 100644 arch/arm/configs/omap_3630sdp_defconfig >> create mode 100644 arch/arm/configs/omap_zoom3_defconfig >> create mode 100755 arch/arm/mach-omap2/board-3630sdp.c >> create mode 100755 arch/arm/mach-omap2/board-zoom-peripherals.c >> mode change 100644 => 100755 arch/arm/mach-omap2/board-zoom2.c >> create mode 100755 arch/arm/mach-omap2/board-zoom3.c >> create mode 100644 arch/arm/mach-omap2/sdram-hynix-h8mbx00u0mer-0em.h > >-- >To unsubscribe from this list: send the line "unsubscribe linux-omap" in >the body of a message to majordomo@vger.kernel.org >More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 16+ messages in thread
end of thread, other threads:[~2009-11-04 7:09 UTC | newest] Thread overview: 16+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2009-11-03 21:20 [PATCH 0/8] RFC: introduce 3630 boards Vikram Pandita 2009-11-03 21:20 ` [PATCH 1/8] omap: 3630: update is_chip variable Vikram Pandita 2009-11-03 21:20 ` [PATCH 2/8] omap: DEBUG_LL: allow no omap uart configuration Vikram Pandita 2009-11-03 21:20 ` [PATCH 3/8] omap: zoom2: split baord file for reuse Vikram Pandita 2009-11-03 21:20 ` [PATCH 4/8] omap: zoom2: update defconfig Vikram Pandita 2009-11-03 21:20 ` [PATCH 5/8] omap: zoom3: introduce zoom3 board support Vikram Pandita 2009-11-03 21:20 ` [PATCH 6/8] omap: zoom3: defconfig creation Vikram Pandita 2009-11-03 21:20 ` [PATCH 7/8] omap: 3630sdp: introduce 3630 sdp board support Vikram Pandita 2009-11-03 21:20 ` [PATCH 8/8] omap: 3630sdp: defconfig creation Vikram Pandita 2009-11-03 22:31 ` [PATCH 7/8] omap: 3630sdp: introduce 3630 sdp board support Nishanth Menon 2009-11-03 22:28 ` [PATCH 5/8] omap: zoom3: introduce zoom3 " Nishanth Menon 2009-11-04 7:09 ` [PATCH 4/8] omap: zoom2: update defconfig G, Manjunath Kondaiah 2009-11-03 22:17 ` [PATCH 3/8] omap: zoom2: split baord file for reuse Nishanth Menon 2009-11-03 22:09 ` [PATCH 2/8] omap: DEBUG_LL: allow no omap uart configuration Nishanth Menon 2009-11-03 21:23 ` [PATCH 0/8] RFC: introduce 3630 boards Pandita, Vikram 2009-11-03 21:26 ` Pandita, Vikram
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox