public inbox for linux-omap@vger.kernel.org
 help / color / mirror / Atom feed
From: Mike Rapoport <mike@compulab.co.il>
To: Phaneendra Kumar Alapati <phani@embwise.com>
Cc: "linux-omap@vger.kernel.org" <linux-omap@vger.kernel.org>,
	Madhusudhan Chikkature <madhu.cr@ti.com>,
	"linux-mmc@vger.kernel.org" <linux-mmc@vger.kernel.org>,
	Adrian Hunter <adrian.hunter@nokia.com>,
	"Paasikivi Teemu.3 (EXT-Ixonos/Tampere)"
	<ext-teemu.3.paasikivi@nokia.com>
Subject: Re: [PATCH] OMAP35xx:SDIO IRQ Support for OMAP35xx
Date: Mon, 21 Dec 2009 18:46:36 +0200	[thread overview]
Message-ID: <4B2FA66C.7010902@compulab.co.il> (raw)
In-Reply-To: <1261400646-7641-1-git-send-email-phani@embwise.com>

Hi,

Phaneendra Kumar Alapati wrote:
> This patch adds SDIO IRQ support for OMAP35xx. Tested on OMAP3530EVM
> with Marvell 88W8686 card and below are the observed throughput results
> (ttcp utility): 13Mbps (Downlink), 10.5 Mbps(Uplink)
>
> Signed-off-by: Phaneendra Kumar <phani@embwise.com>
> ---
>  drivers/mmc/host/omap_hsmmc.c |   55 ++++++++++++++++++++++++++++++++++++----
>  1 files changed, 49 insertions(+), 6 deletions(-)

I've tried the patch on CM-T35 that has Marvell 88W8686 on-board and
surprisingly I get a lot of command timeouts from the libertas driver :(
---
libertas: requeueing command 0x0006 due to timeout (#1)
libertas: Received result 0 to command 6 after 1 retries
libertas: command 0x0006 timed out
---
I hope I'll find time to debug it in the next few days and provide more valuable
information...


> diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
> index 4b23225..fa94580 100644
> --- a/drivers/mmc/host/omap_hsmmc.c
> +++ b/drivers/mmc/host/omap_hsmmc.c
> @@ -100,6 +100,10 @@
>  #define SRD			(1 << 26)
>  #define SOFTRESET		(1 << 1)
>  #define RESETDONE		(1 << 0)
> +#define CIRQ		(1 << 8)
> +#define CIRQ_ENABLE	(1 << 8)
> +#define CTPL		(1 << 11)
> +#define CLKEXTFREE	(1 << 16)
>  
>  /*
>   * FIXME: Most likely all the data using these _DEVID defines should come
> @@ -171,6 +175,7 @@ struct omap_hsmmc_host {
>  	int			vdd;
>  	int			protect_card;
>  	int			reqs_blocked;
> +	int			sdio_int;
>  
>  	struct	omap_mmc_platform_data	*pdata;
>  };
> @@ -436,6 +441,13 @@ omap_hsmmc_start_command(struct omap_hsmmc_host *host, struct mmc_command *cmd,
>  	else
>  		OMAP_HSMMC_WRITE(host->base, IE, INT_EN_MASK);
>  
> +	if (host->sdio_int) {
> +		OMAP_HSMMC_WRITE(host->base, ISE,
> +			(OMAP_HSMMC_READ(host->base, ISE) | CIRQ_ENABLE));
> +		OMAP_HSMMC_WRITE(host->base, IE,
> +			(OMAP_HSMMC_READ(host->base, IE) | CIRQ_ENABLE));
> +	}
> +
>  	host->response_busy = 0;
>  	if (cmd->flags & MMC_RSP_PRESENT) {
>  		if (cmd->flags & MMC_RSP_136)
> @@ -640,6 +652,17 @@ static irqreturn_t omap_hsmmc_irq(int irq, void *dev_id)
>  
>  	spin_lock(&host->irq_lock);
>  
> +	data = host->data;
> +	status = OMAP_HSMMC_READ(host->base, STAT);
> +	dev_dbg(mmc_dev(host->mmc), "IRQ Status is %x\n", status);
> +
> +	if (host->mmc->caps & MMC_CAP_SDIO_IRQ) {
> +		if (status & CIRQ) {
> +			dev_dbg(mmc_dev(host->mmc), "SDIO Card Interrupt\n");
> +			mmc_signal_sdio_irq(host->mmc);
> +		}
> +	}
> +
>  	if (host->mrq == NULL) {
>  		OMAP_HSMMC_WRITE(host->base, STAT,
>  			OMAP_HSMMC_READ(host->base, STAT));
> @@ -649,10 +672,6 @@ static irqreturn_t omap_hsmmc_irq(int irq, void *dev_id)
>  		return IRQ_HANDLED;
>  	}
>  
> -	data = host->data;
> -	status = OMAP_HSMMC_READ(host->base, STAT);
> -	dev_dbg(mmc_dev(host->mmc), "IRQ Status is %x\n", status);
> -
>  	if (status & ERR) {
>  #ifdef CONFIG_MMC_DEBUG
>  		omap_hsmmc_report_irq(host, status);
> @@ -1254,6 +1273,25 @@ static int omap_hsmmc_get_ro(struct mmc_host *mmc)
>  	return mmc_slot(host).get_ro(host->dev, 0);
>  }
>  
> +static void omap_hsmmc_enable_sdio_irq(struct mmc_host *mmc, int enable)
> +{
> +	struct omap_hsmmc_host *host = mmc_priv(mmc);
> +
> +	host->sdio_int = enable;
> +	if (enable) {
> +		OMAP_HSMMC_WRITE(host->base, ISE,
> +			(OMAP_HSMMC_READ(host->base, ISE) | CIRQ_ENABLE));
> +		OMAP_HSMMC_WRITE(host->base, IE,
> +			(OMAP_HSMMC_READ(host->base, IE) | CIRQ_ENABLE));
> +	} else {
> +		OMAP_HSMMC_WRITE(host->base, IE,
> +			(OMAP_HSMMC_READ(host->base, IE) & (~CIRQ_ENABLE)));
> +		OMAP_HSMMC_WRITE(host->base, ISE,
> +			(OMAP_HSMMC_READ(host->base, ISE) & (~CIRQ_ENABLE)));
> +	}
> +
> +}
> +
>  static void omap_hsmmc_conf_bus_power(struct omap_hsmmc_host *host)
>  {
>  	u32 hctl, capa, value;
> @@ -1519,7 +1557,7 @@ static const struct mmc_host_ops omap_hsmmc_ops = {
>  	.set_ios = omap_hsmmc_set_ios,
>  	.get_cd = omap_hsmmc_get_cd,
>  	.get_ro = omap_hsmmc_get_ro,
> -	/* NYET -- enable_sdio_irq */
> +	.enable_sdio_irq = omap_hsmmc_enable_sdio_irq,
>  };
>  
>  static const struct mmc_host_ops omap_hsmmc_ps_ops = {
> @@ -1529,7 +1567,7 @@ static const struct mmc_host_ops omap_hsmmc_ps_ops = {
>  	.set_ios = omap_hsmmc_set_ios,
>  	.get_cd = omap_hsmmc_get_cd,
>  	.get_ro = omap_hsmmc_get_ro,
> -	/* NYET -- enable_sdio_irq */
> +	.enable_sdio_irq = omap_hsmmc_enable_sdio_irq,
>  };
>  
>  #ifdef CONFIG_DEBUG_FS
> @@ -1657,6 +1695,7 @@ static int __init omap_hsmmc_probe(struct platform_device *pdev)
>  	host->mapbase	= res->start;
>  	host->base	= ioremap(host->mapbase, SZ_4K);
>  	host->power_mode = -1;
> +	host->sdio_int = 0;
>  
>  	platform_set_drvdata(pdev, host);
>  	INIT_WORK(&host->mmc_carddetect_work, omap_hsmmc_detect);
> @@ -1744,6 +1783,10 @@ static int __init omap_hsmmc_probe(struct platform_device *pdev)
>  	if (mmc_slot(host).nonremovable)
>  		mmc->caps |= MMC_CAP_NONREMOVABLE;
>  
> +	mmc->caps |= MMC_CAP_SDIO_IRQ;
> +	OMAP_HSMMC_WRITE(host->base, CON,
> +			OMAP_HSMMC_READ(host->base, CON) | (CTPL | CLKEXTFREE));
> +
>  	omap_hsmmc_conf_bus_power(host);
>  
>  	/* Select DMA lines */

-- 
Sincerely yours,
Mike.


  reply	other threads:[~2009-12-21 16:46 UTC|newest]

Thread overview: 8+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2009-12-21 13:04 [PATCH] OMAP35xx:SDIO IRQ Support for OMAP35xx Phaneendra Kumar Alapati
2009-12-21 16:46 ` Mike Rapoport [this message]
2010-01-20 17:36   ` Dirk Behme
2010-01-21  6:36     ` Mike Rapoport
  -- strict thread matches above, loose matches on Subject: below --
2009-12-10  7:24 [PATCH]OMAP35xx:SDIO " Phaneedra Kumar Alapati
2009-12-10  9:20 ` Adrian Hunter
2009-12-10 17:32   ` Madhusudhan
2009-12-15 23:22     ` Madhusudhan

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=4B2FA66C.7010902@compulab.co.il \
    --to=mike@compulab.co.il \
    --cc=adrian.hunter@nokia.com \
    --cc=ext-teemu.3.paasikivi@nokia.com \
    --cc=linux-mmc@vger.kernel.org \
    --cc=linux-omap@vger.kernel.org \
    --cc=madhu.cr@ti.com \
    --cc=phani@embwise.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox