From mboxrd@z Thu Jan 1 00:00:00 1970 From: Michael Trimarchi Subject: Re: ISP OMAP3 camera support ov7690 Date: Tue, 12 Jan 2010 18:32:49 +0100 Message-ID: <4B4CB241.6050603@panicking.kicks-ass.org> References: <4AC7DAAD.2020203@panicking.kicks-ass.org> <4AC8B764.2030101@gmail.com> <4AC93DC9.2080809@panicking.kicks-ass.org> <4B4C75F0.3060108@panicking.kicks-ass.org> Mime-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1; format=flowed Content-Transfer-Encoding: 7bit Return-path: Received: from ms01.sssup.it ([193.205.80.99]:56234 "EHLO sssup.it" rhost-flags-OK-OK-OK-FAIL) by vger.kernel.org with ESMTP id S1751083Ab0ALRcx (ORCPT ); Tue, 12 Jan 2010 12:32:53 -0500 In-Reply-To: Sender: linux-omap-owner@vger.kernel.org List-Id: linux-omap@vger.kernel.org To: "Aguirre, Sergio" Cc: Nishanth Menon , "linux-omap@vger.kernel.org" , "linux-media@vger.kernel.org" Hi all, Aguirre, Sergio wrote: > >> -----Original Message----- >> From: Michael Trimarchi [mailto:michael@panicking.kicks-ass.org] >> Sent: Tuesday, January 12, 2010 7:15 AM >> To: Aguirre, Sergio >> Cc: Nishanth Menon; linux-omap@vger.kernel.org; linux- >> media@vger.kernel.org >> Subject: Re: ISP OMAP3 camera support ov7690 >> >> Hi all, >> >> Now I have a good camera pcb and I can test again the driver. My board is >> an overo gumstix board. > > Excellent! > > Please let me know if you're having issues with it. > > Thanks for your interest! > > Regards, > Sergio > maybe I have done some mistake during writing the email, but I have asked few things inside the email. The camera part is ok because I have written a driver using the ov538 bridge but I have some problem in configuring the isp omap3 device. It opens correctly the camera, and set xclk frequency. Then seems that vsync and hsync are not routed to the engine because I don't receive any interrupt. >> Aguirre Rodriguez, Sergio Alberto wrote: >>> Hi Michael, >>> >>>> -----Original Message----- >>>> From: linux-omap-owner@vger.kernel.org >>>> [mailto:linux-omap-owner@vger.kernel.org] On Behalf Of michael >>>> Sent: Sunday, October 04, 2009 7:29 PM >>>> To: Nishanth Menon >>>> Cc: linux-omap@vger.kernel.org; linux-media@vger.kernel.org >>>> Subject: Re: ISP OMAP3 camera support ov7690 >>>> >>>> Hi, >>>> >>>> cc: linux-media >>>> >>>> Nishanth Menon wrote: >>>>> michael said the following on 10/03/2009 06:13 PM: >>>>>> I'm writing a driver to support the ov7690 camera and I have some >>>>>> question about the meaning of: >>>>>> >>>>>> - datalane configuration >>>>> CSI2 Data lanes - each CSI2 lane is a differential pair. >>>> And, at least 1 >>>>> clock and data lane is used in devices. >>>> Sorry can you explain a little bit more. I have the camera >>>> connected to the >>>> cam_hs and cam_vs and the data is 8Bit. I use the the isp init >>>> structure. The sccb bus works great and I can send >>>> configuration to it, >>>> but I don't receive any interrupt from the ics, seems that it >>>> doen't see >>>> the transaction: >>>> >>>> The ISPCCDC: ###CCDC SYN_MODE=0x31704 seems ok. >>>> >>>> >>>> static struct isp_interface_config ov7690_if_config = { >>>> .ccdc_par_ser = ISP_CSIA, >>>> .dataline_shift = 0x0, >>>> .hsvs_syncdetect = ISPCTRL_SYNC_DETECT_VSFALL, >>> Can you try with ISPCTRL_SYNC_DETECT_VSRISE ? >>> >>>> .strobe = 0x0, >>>> .prestrobe = 0x0, >>>> .shutter = 0x0, >>>> .wenlog = ISPCCDC_CFG_WENLOG_AND, >>>> .wait_hs_vs = 0x4, >>>> .raw_fmt_in = ISPCCDC_INPUT_FMT_GR_BG, >>>> .u.csi.crc = 0x0, >>>> .u.csi.mode = 0x0, >>>> .u.csi.edge = 0x0, >>>> .u.csi.signalling = 0x0, >>>> .u.csi.strobe_clock_inv = 0x0, >>>> .u.csi.vs_edge = 0x0, >>>> .u.csi.channel = 0x0, >>>> .u.csi.vpclk = 0x1, >>>> .u.csi.data_start = 0x0, >>>> .u.csi.data_size = 0x0, >>>> .u.csi.format = V4L2_PIX_FMT_YUYV, >>>> }; >>>> >>>> and I don't know the meaning of >>>> >>>> lanecfg.clk.pol = OV7690_CSI2_CLOCK_POLARITY; >>>> lanecfg.clk.pos = OV7690_CSI2_CLOCK_LANE; >>>> lanecfg.data[0].pol = OV7690_CSI2_DATA0_POLARITY; >>>> lanecfg.data[0].pos = OV7690_CSI2_DATA0_LANE; >>>> lanecfg.data[1].pol = OV7690_CSI2_DATA1_POLARITY; >>>> lanecfg.data[1].pos = OV7690_CSI2_DATA1_LANE; >>>> lanecfg.data[2].pol = 0; >>>> lanecfg.data[2].pos = 0; >>>> lanecfg.data[3].pol = 0; >>>> lanecfg.data[3].pos = 0; >>>> >>> This is the physical connection details: >>> >>> - The .pol field stands for the differntial pair polarity. >>> (i.e. the order in which the negative and positive connections >>> are pugged in to the CSI2 ComplexIO module) >> What exact the meaning of the pol, sorry? I have a signal that is >> connected >> to a pin. If the pos is avalaible can I use it? >> It's not important how to route the signal but don't route on the same >> lane. >> Is it right? >> >> This is the timing of the camera so I can check signal, but I don't >> receive interrupt >> of isp engine >> >> The camera is direct connected to the >> camera omap camera signal and using the oscilloscope I can see the hs/vs >> signal >> The hs is low and go up, like the vs signal. I have only one camera >> with that use D0 to D7 data bit. >> >> http://www.gumstix.net/Hardware/view/I/O-connectors-cabling/Gumstix-Overo- >> 27-pin-connector-J5-to-manage-camera-controls/112.html >> >> static struct isp_interface_config ov7690_if_config = { >> .ccdc_par_ser = ISP_CSIA, >> .dataline_shift = 0x0, >> .hsvs_syncdetect = ISPCTRL_SYNC_DETECT_VSRISE, >> .strobe = 0x0, >> .prestrobe = 0x0, >> .shutter = 0x0, >> .wenlog = ISPCCDC_CFG_WENLOG_AND, >> .wait_hs_vs = 0x4, >> .raw_fmt_in = ISPCCDC_INPUT_FMT_GR_BG, >> .u.csi.crc = 0x0, >> .u.csi.mode = 0x0, >> .u.csi.edge = 0x0, >> .u.csi.signalling = 0x0, >> .u.csi.strobe_clock_inv = 0x0, >> .u.csi.vs_edge = 0x0, >> .u.csi.channel = 0x0, >> .u.csi.vpclk = 0x1, >> .u.csi.data_start = 0x0, >> .u.csi.data_size = 0x0, >> .u.csi.format = V4L2_PIX_FMT_YUYV, >> }; >> >> This is my initial configuration >> #define OV7690_CSI2_CLOCK_POLARITY 0 /* +/- pin order */ >> #define OV7690_CSI2_DATA0_POLARITY 0 /* +/- pin order */ >> #define OV7690_CSI2_DATA1_POLARITY 0 /* +/- pin order */ >> #define OV7690_CSI2_CLOCK_LANE 1 /* Clock lane position: 1 >> */ >> #define OV7690_CSI2_DATA0_LANE 2 /* Data0 lane position: 2 >> */ >> #define OV7690_CSI2_DATA1_LANE 3 /* Data1 lane position: 3 >> */ >> tim#define OV7690_CSI2_PHY_THS_TERM 2 >> #define OV7690_CSI2_PHY_THS_SETTLE 23 >> #define OV7690_CSI2_PHY_TCLK_TERM 0 >> #define OV7690_CSI2_PHY_TCLK_MISS 1 >> #define OV7690_CSI2_PHY_TCLK_SETTLE 14 >> >> With this clock polarity >> >> lanecfg.clk.pol = OV7690_CSI2_CLOCK_POLARITY; >> lanecfg.clk.pos = OV7690_CSI2_CLOCK_LANE; >> lanecfg.data[0].pol = OV7690_CSI2_DATA0_POLARITY; >> lanecfg.data[0].pos = OV7690_CSI2_DATA0_LANE; >> lanecfg.data[1].pol = OV7690_CSI2_DATA1_POLARITY; >> lanecfg.data[1].pos = OV7690_CSI2_DATA1_LANE; >> lanecfg.data[2].pol = 0; >> lanecfg.data[2].pos = 0; >> lanecfg.data[3].pol = 0; >> lanecfg.data[3].pos = 0; >> isp_csi2_complexio_lanes_config(&isp->isp_csi2, &lanecfg); >> >> Michael > -- Regards Michael > To unsubscribe from this list: send the line "unsubscribe linux-media" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html >